Search NASA⌕ Search

SEARCH · Search NASA

Results for “Finite Element Fuel Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

BISON: A Finite Element-Based Nuclear Fuel Performance Code

BISON is a finite element-based nuclear fuel performance code applicable to a variety of fuel forms including light water reactor fuel rods, TRISO particle fuel, and metallic rod and plate fuel. It is a multiphysics fuel analysis tool that solves fully-coupled thermomechanical problems. BISON is based on MOOSE and can efficiently solve problems using standard workstations or very large high-performance computers in a variety of different dimensions, including full 3D, 2D-RZ axisymmetric, layered axisymmetric 1D, and spherically symmetric 1D systems. It is developed by a team of scientists and engineers at Idaho National Laboratory and by collaborators. The development of BISON is supported by various funding agencies, principally the United States Department of Energy.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessment of buffer-IPyC thermomechanical debonding behavior using new experimental strength data in BISON

TRIstructural ISOtropic (TRISO) fuel is a nuclear fuel commonly used in High Temperature Gas-cooled Reactors (HTGRs). A single sub-millimeter-diameter TRISO fuel particle consists of a spherical fuel kernel surrounded by four coating layers: a low-density pyrocarbon buffer layer, an inner pyrolytic carbon (IPyC) layer, a silicon carbide (SiC) layer, and an outer pyrolytic carbon (OPyC) layer. The kernel is commonly made of UO2 or a mixture of uranium carbide and uranium oxide (UCO). During reactor operation, the TRISO coating layers are subjected to irradiation-induced dimensional changes and the associated thermomechanical behavior of each layer. One of the observed behaviors is gap formation between the buffer and IPyC layer due to the porous buffer’s irradiation-induced shrinkage exceeding that of the IPyC layer. Not all irradiated particles will experience buffer-IPyC gap formation. The debonding may be partial, or it may be nearly total. However, from post-irradiation examination of UCO TRISO fuels irradiated as part of the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program, it was concluded that partial buffer-IPyC debonding was the most common type of buffer-IPyC interaction. To predict TRISO thermomechanical performance, multi-physics models have been built that are being continually updated and refined. The BISON code is a finite element-based nuclear fuel performance code that may be used for 1D, 2D, and 3D TRISO particle simulations. This code is used to calculate fuel temperature, kernel swelling, buffer densification, thermal and irradiation creep, fracture, and fission gas production and release. One of the recent additions to the BISON code is the ability to model the process of layer debonding. This paper will focus on the simulation results of the improved BISON debonding model that will utilize updated strengths measured from irradiated AGR TRISO fuel particles. The new experimental strength data from micromechanical tests of irradiated TRISO fuel samples were exercised in the BISON simulations and compared to baseline strength data to assess their applicability in the models. This also includes updated buffer-IPyC bond strengths to simulate layer delamination. Based on current experimental observations it is noted that the buffer-IPyC separation occurs not exactly at the junction of these two layers, but more on the side of the buffer layer. That observation is also implemented in the TRISO interface debonding model. This improved modeling approach using experimental strength data to characterize buffer-IPyC debonding and its potential subsequent cracking will be presented in the paper along with comparisons to available experimental observations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessment of Buffer-IPyC Thermomechanical Debonding Behavior Using New Experiment Strength Data in BISON

TRIstructural ISOtropic (TRISO) single sub-millimeter-diameter nuclear fuel particle consists of a spherical fuel kernel surrounded by four coating layers. During reactor operation, the TRISO coating layers are subjected to irradiation-induced dimensional changes and the associated thermomechanical behavior of each layer. One of the observed behaviors is gap formation between the buffer and IPyC layer due to the porous buffer’s irradiation-induced shrinkage exceeding that of the IPyC layer. To predict TRISO thermomechanical performance, multi-physics models have been built that are continually updated and refined. The BISON code is a finite element-based nuclear fuel performance code that may be used for TRISO particle simulations. One of the recent additions to the BISON code is the ability to model the process of layer debonding. This paper will focus on the simulation results of the improved BISON debonding model that will utilize updated strengths measured from irradiated TRISO fuel particles. The new experimental strength data from micromechanical tests of irradiated TRISO fuel samples were exercised in the BISON simulations and compared to baseline strength data to assess their applicability in the models. This also includes updated buffer-IPyC bond strengths to simulate layer delamination. Based on current experimental observations it is noted that the buffer-IPyC separation occurs not exactly at the junction of these two layers, but more on the side of the buffer layer. This improved modeling approach using experimental strength data to characterize buffer-IPyC debonding and its potential subsequent cracking will be presented in the paper along with comparisons to available experimental observations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Advancing SiC clad fuel performance model: bridging micro- and macro-scale models and experimental validation

This report presents a workflow for advancing fuel performance modeling of SiC composite cladding for light-water reactors by linking microscale, experimental data-informed finite element analysis with rod-scale fuel performance codes such as BISON. The workflow uses X-ray computed tomography (XCT) to capture the actual geometry and processing-induced defects of as-fabricated SiC composite tube specimens, particularly porosity and wall-thickness variations, and converts the segmented XCT volumes into image-based finite element meshes for high fidelity structural analysis.

Koyanagi, Takaaki [Oak Ridge National Laboratory (↗
DOE OSTI2025

Mechanistic Multiscale Uncertainty Propagation in Support of Accelerated Fuel Qualification

Taking a nuclear fuel concept through the research, development, and qualification stages has historically taken on the order of 20 to 25 years because of extensive irradiation tests required for a variety of conditions. The concept of accelerated fuel qualification (AFQ) has been proposed to increase the innovation pace for nuclear fuels. The goal of AFQ is not to replace the traditional qualification approach but rather to reduce the total number of experiments required to ensure approval from the regulatory authority. Of the many AFQ approaches being explored, advanced modeling—and, in particular, mechanistic modeling—is in a uniquely cross-cutting position to reduce the number of required integral tests through the inclusion of separate-effects testing, while helping to extrapolate reactor performance during rare events. We make the case that propagation of uncertainty through various computational length scales helps contextualize mechanistic modeling. We will utilize UO 2 fission gas diffusion predictions from the atomistically informed cluster dynamics code Centipede to inform fuel performance rodlet simulations using the BISON finite element code as the metric for showing how multiscale mechanistic uncertainty quantification can help reduce uncertainty in fuel performance. In conclusion, by quantifying uncertainty and its reduction through multiscale modeling, the qualification process may be accelerated through the reduction of costly irradiation experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Multiscale Modeling of the Mechanical Response of Silicon Carbide Composite Within the Accelerated Fuel Qualification Framework

The accelerated fuel qualification (AFQ) framework has been used for the initial development of multiscale modeling of silicon carbide (SiC) fiber reinforced composite (SiC-SiC). The AFQ framework provides a methodology to leverage physics-informed multiscale modeling along with a reduced set of empirical test data to reduce the time and cost of licensing and qualification of new nuclear fuel systems while maintaining the overall nuclear power plant safety case. SiC-SiC is being proposed for in-core applications, most notably fuel cladding, for current and next-generation nuclear reactors because of its high temperature stability, irradiation tolerance, and ability to withstand many accident conditions. As these composites exhibit multiscale architectures and complex microstructure-based fracture mechanics, it is an appealing use case for the AFQ methodology. While the end goal of this work is a single multiscale model that can be used for predictive in-core performance, current focus is on the individual various length scale models. Four individual models have been initially developed from microscale to engineering system level to capture key physics-based effects across different length scales. These models include a microscale homogenized tow model, a mesoscale fast Fourier transform–based weave model that integrates the homogenized tow model, a mesoscale finite element–based weave model, and a system-level BISON fuel performance model. Results of these models have undergone an initial comparison with separate-effects test data showing a good match to experimental results. By using the AFQ framework during model development, several near-term benefits have been secured including a reduction in development time for the SiC-SiC cladding, more targeted irradiation testing, and a better understanding of uncertainty.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessment of MiniFuel Subcapsule Design Recommendations on Previous Experiments

MiniFuel describes the class of separate effects nuclear fuels irradiation experiments that have been conducted in the High Flux Isotope Reactor (HFIR) since 2018. These experiments comprise a stack of six fuel-bearing subcapsules contained in a stainless steel target housing that is in contact with HFIR coolant on its exterior. All MiniFuel targets have a near-standardized architecture, and the primary design variables that change between experiments are the radial gap size between the subcapsule and housing and the target fill gas composition. Finite element heat transfer models are used to determine the optimum gas composition and gap sizes, and recent studies were performed to identify model parameters that contribute the most uncertainty to fuel specimen temperature predictions. That work, which is referenced herein, also recommended a set of design modifications to the subcapsule internal architecture and assembly process. These modifications are intended to reduce fuel temperature uncertainty in future experiments. In this report, the subcapsule design modifications were retroactively applied to a previously conducted MiniFuel experiment to determine how these changes affect the established safety and performance envelope of the experimental capability. These effects were determined in two steps. First, the modifications were applied to the subcapsule design without any other changes to determine their isolated effect on the predicted fuel specimen temperatures. This portion of the analysis showed that fuel temperatures were modestly reduced because the implemented changes improved heat transfer efficacy. Next, traditional MiniFuel design activities (i.e., sizing the gas gaps and determining the fill gas composition) were reperformed, and they confirmed that the original desired fuel temperatures could be achieved while remaining within established safety limits. Therefore, this report demonstrates improved performance resulting from the subcapsule modifications, which mitigate uncertainty while meeting the objectives of past experiments. An additional benefit of the design changes is reduced sensitivity of the fuel temperature to the evolving flux spectrum in HFIR, leading to more stable temperatures and enhanced utility of MiniFuel as a separate effects irradiation platform.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Development and preliminary validation of a mechanistic multiscale model for fuel-cladding chemical interaction in metallic nuclear fuels

Despite decades of fuel rod material and design improvements, fuel-cladding chemical interaction (FCCI) remains the single-most lifetime-limiting behavior for modern metallic fuel rods. Constraining fuel lifetime increases operating costs, limiting the economic viability of commercializing metallic nuclear fuel technology. A mechanistic multiscale model utilizing the finite element method-based MARMOT and BISON codes was developed to more confidently predict cladding-side FCCI and its impact on fuel performance. The new BISON model incorporates mesoscale models for the effects of fuel microstructure evolution on the transport of wastage-inducing lanthanides through the fuel and for the kinetics of cladding wastage layer growth. The mesoscale models, in turn, build on lanthanide transport property data obtained from the atomistic scale. Preliminary validation studies using wastage thickness and cladding profilometry data from four fuel rods irradiated in Experimental Breeder Reactor II experiment X447 and one fuel rod from Fast Flux Test Facility experiment IFR1 show that the new model predicts cladding wastage and its effects on cladding deformation as well as existing empirical FCCI correlations. The new model is expected to aid in the design of new metallic fuel concepts, including fuel additives, cladding liners, and sodium-free annular fuel geometries. In conclusion, future work will focus on broader validation and refinement of the model’s treatment of different fuel alloys and cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

AGR-5/6/7 Thermal Model with Non-uniform Gas Gaps

Fuel compact temperatures are a crucial factor in assessing the irradiation performance of tri-structural isotropic fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a three-dimensional finite element thermal model, which is subject to simulation uncertainty. The most dominant factor in the uncertainty of calculated fuel temperatures is the gas gap uncertainty due to the nub-to-shell clearance caused by a design error of AGR-5/6/7 capsules. The thermal model was revised to examine the most probable graphite offset position for six different days during the irradiation for Capsules 1 and 2. The analysis varied the offset distance and azimuthal direction at both the top and bottom of the holder. The best-fit offset was estimated based on the minimum root mean square error of the residuals (measured minus calculated) for the operational thermocouples (TCs). From these results, the following conclusions were made: (1) The holder offsets led to slightly lower average temperatures but wider temperature variations (lower minimum and higher peak fuel temperatures) for both Capsule 1 and Capsule 2. (2) During earlier cycles (162A–164B), when numerous TCs were still operational, the best-fit offset distance varied over a specific range for both the top and bottom ([0.002–0.0035 in.] for Capsule 1 and [0.003-0.004 in] for Capsule 2). In contrast, the offset azimuthal direction varied widely, especially for the offset at the bottom of the Capsule 1 holder. This is because holder movement was somewhat constrained at the top of Capsule 1 by the TC leads running through the capsule head and into the holder and by the through tubes in Capsule 2, but the Capsule 1 bottom did not have this type of constraint. (3) During later cycles, when all TCs failed, applying the maximum possible offset of 0.006 in. to the northwest direction for both the top and bottom resulted in a calculated peak fuel temperature of 1557? in Capsule 1 (i.e., a 135? increase from 1422? with zero offset on September 20, 2019 (166A)); the maximum offset of 0.0068 in. to the south for both top and bottom resulted in a calculated peak fuel temperature of 1110°C in Capsule 2 on April 20, 2020 (i.e., a 116? increase from 994? with zero offset (168A)). High peak fuel temperatures in Capsule 1 during Cycle 166A could be the cause of massive particle failure near the end of this cycle. (4) Even though the highest temperature at the tip of Type-N TCs, such as TC-1-7, slightly exceeded 1000?, the temperature along the TC wire reached as high as 1335? assuming an offset of 0.006 in. in the northwest of Capsule 1 holder near the end of Cycle 166A. This temperature significantly exceeds the temperature threshold at which TC degradation is expected to occur, ultimately contributing to considerable particle failures in Capsule 1. For eight Type-N TCs in Capsule 2, the peak TC line temperature was much lower (i.e., 1029°C for TC-2-5), assuming maximum offset of 00068 in. to the south during cycle 168A.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Estimation of Fission Product Transport Parameters for Cesium in the AGR-3/4 TRISO Fuel Experiment

A one-dimensional (1D) finite-element model of fission product transport in the AGR-3/4 experiment has been developed using the Multiphysics Object Oriented Simulation Environment (MOOSE) framework and implemented in the fuel performance code, BISON. The model resolves capsule-specific geometries, materials, and temperature histories and simulates radial migration of fission products from the fuel compact through the inner ring, outer ring, and into the sink ring. Model parameters governing diffusion and sorption were estimated for key fission products – cesium (Cs), and europium (Eu) – by simultaneously fitting modeled isotopic concentration profiles and total ring inventories to a post-irradiation experimental measurement. These data include gamma scanning, liquid scintillation for Sr-90, radial deconsolidation leach-burn-leach analysis, tomographic reconstructions, and destructive physical sampling. A mortar-based interfacial sorption framework was implemented to enforce physically consistent mass transfer and flux conservation across gas gaps. Two classes of parameter sets were derived: a least-squares best-fit, and a safety-oriented conservative-fit, what applies strong penalties for underprediction of sink inventories. Across all twelve capsules, the model successfully reproduces the dominant radial transport trends for Cs, Sr, with decreasing concentrations from the compact outward through successive rings. Cs behavior is captured most consistently, while strontium predictions reveal systematic trade-offs between compact accuracy and conservative sink-ring bounding. The results demonstrate that sink ring weighted calibration provides conservative, safety relevant bounds on low temperature fission product transport, but at the cost of underpredicting compact inventories for Sr isotopes. These discrepancies highlight the need for additional physics, including fast-slow diffusion model, incorporating trapping mechanism in the transport behavior. Overall, this work establishes a robust, capsule-specific modeling framework for AGR-3/4 fission product transport and provides a defensible basis for parameter selection in source-term and fuel performance analyses for high temperature gas-cooled reactors.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Uncertainty Quantification of Fatigue Behavior of Rough AM Surfaces and Microstructures to Enable Hydrogen Gas Turbine

Modifying fossil-fueled industrial gas turbines to utilize low or zero-carbon fuels, such as hydrogen or hydrogen-natural gas blends, is a complex endeavor. The successful implementation of this technology hinges on three key design criteria: (1) developing new fuel injectors capable of efficiently burning alternative fuels, (2) ensuring manufacturability to meet cost and time-to-market goals, and (3) achieving component durability in the demanding environment of an operating gas turbine. Additive manufacturing (AM) accelerates product development, yet concerns persist regarding the durability of parts with rough AM surfaces. A fully experimental approach to quantify the fatigue performance of rough AM microstructures is both costly and labor-intensive. To address this, ORNL and Solar Turbines Incorporated (Solar) employed a crystal plasticity finite element (CPFE) model to identify the factors influencing AM surface fatigue behavior. These CPFE findings, combined with targeted experimental data, were used to develop a computationally efficient surrogate model suitable for assessing the lifespan of gas turbine engine components.

08 HYDROGEN↗
DOE OSTI2024

Nanoscopic Imaging of Self-Propelled Ultrasmall Catalytic Nanomotors

Ultrasmall nanomotors (<100 nm) are highly desirable nanomachines for their size-specific advantages over their larger counterparts in applications spanning nanomedicine, directed assembly, active sensing, and environmental remediation. While there are extensive studies on motors larger than 100 nm, the design and understanding of ultrasmall nanomotors have been scant due to the lack of high-resolution imaging of their propelled motions with orientation and shape details resolved. Here, we report the imaging of the propelled motions of catalytically powered ultrasmall nanomotors─hundreds of them─at the nanometer resolution using liquid-phase transmission electron microscopy. These nanomotors are Pt nanoparticles of asymmetric shapes (“tadpoles” and “boomerangs”), which are colloidally synthesized and observed to be fueled by the catalyzed decomposition of NaBH4 in solution. Statistical analysis of the orientation and position trajectories of fueled and unfueled motors, coupled with finite element simulation, reveals that the shape asymmetry alone is sufficient to induce local chemical concentration gradient and self-diffusiophoresis to act against random Brownian motion. Our work elucidates the colloidal design and fundamental forces involved in the motions of ultrasmall nanomotors, which hold promise as active nanomachines to perform tasks in confined environments such as drug delivery and chemical sensing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Sensitivity analysis of thermal contact conductance modeling to inform MiniFuel irradiation capsule designs

The MiniFuel irradiation platform has been developed by Oak Ridge National Laboratory as a flexible, high-throughput separate effects testing capability within the High Flux Isotope Reactor (HFIR). Finite element thermal models are relied upon to design MiniFuel experiments to achieve a specific time-averaged irradiation temperature for experimental objectives. A previous study identified that uncertainty in the component heat generation rates and thermal contact conductance (TCC) model are the most significant contributors to predicted fuel temperature variance. To address both sources of uncertainty, this work performs sensitivity analysis on the TCC model to identify high-impact, high-uncertainty parameters that contribute to fuel temperature variance. The TCC model is analyzed in increasing detail, first using a standalone Python code, then again after coupling Python to the BISON fuel performance code. Furthermore, the parameters with the largest contributions to fuel temperature variance which can be reduced through design changes are identified as the initial subcapsule gas pressure, contact pressure between the fuel and dish, and the effective surface roughness of the interface. A set of design recommendations for future capsule designs has been established and applied to reduce the previously quantified average fuel temperature uncertainty ranges of ± 40 °C in the HFIR vertical experiment facilities (VXF) and ± 80 °C in the removable beryllium (RB) reflector to approximately ± 32 °C and ± 53 °C, respectively. This equates to a 21 % and 33 % reduction in the uncertainty range of the average fuel temperature for VXF and RB, respectively.

BISON↗
DOE OSTI2026

A Scaling Study for Incompressible Multispecies Solver in Vertex-CFD

Multispecies incompressible flows occur widely in engineering and environmental applications, such as chemical reactors, fuel cells, ocean mixing, and biomedical systems. However, accurately resolving the complex transport and mixing phenomena associated with multiple interacting species remains computationally challenging, especially for large-scale problems. In this study, we present a robust, high-performance computing--enabled multispecies incompressible Navier–Stokes solver integrated within the Vertex-CFD framework. Our solver employs a fully coupled, implicit, finite element--based formulation that accurately captures the advection, diffusion, and interaction of multiple species in incompressible flows by leveraging the Kokkos library for parallel computing to achieve high computational efficiency. For pressure coupling, the entropically damped artificial compressibility method is utilized. We validated the solver against canonical test cases, including multispecies advection, diffusion, and Bateman systems; the results demonstrate second- and third-order spatial accuracy and consistent convergence. Additionally, we demonstrated the strong and weak scaling study results obtained on the leadership-class high-performance computing system, Frontier at Oak Ridge National Laboratory.

Oz, Furkan [ORNL] (ORCID:0000000265831724)↗
DOE OSTI2025

Study of hydride reorientation and ductility of SRA ZIRLO and PRXA ZIRLO using ring compression testing (RCT)

Before dry storage, spent nuclear fuel is dried at high temperatures, which induces hydride dissolution. Radial hydride particles precipitate when cooled under a stress above a threshold stress. This process can severely degrade the ductility of cladding tubes. Zirconium alloys with different microstructures, such as grain boundary density, were quantified and studied to examine their effect on hydride reorientation. The ring compression loading mode creates a range of stress states depending on the location within the ring with respect to the applied load, producing various hydride morphologies that can be used to study the effects of microstructures on hydride reorientation. Finite element modeling was performed to calculate the hoop stress, which is the dominant stress, during hydride reorientation. These results were coupled with hydride morphology to determine the threshold stress for hydride reorientation, depending on the microstructure. In conclusion, the samples were then mechanically tested using ring compression to evaluate the ductility of zirconium alloys as a function of different hydride morphologies.

Hydride embrittlement↗
DOE OSTI2024

Review of recent activities with MOOSE, an open-source finite element & finite volume multi-fidelity simulation framework

Modeling and simulation are an increasing part of engineering. This is undoubtedly driven by the high costs of constructing experimental facilities, but also enabled by the exponential increase in computing powers over the last decades, which allows computational models to be closer than ever to reality. One of the main drivers for the development of MOOSE is supporting advanced nuclear reactor simulations. A challenging aspect of modeling advanced nuclear reactors is the plurality of physics involved, including neutronics, thermal hydraulics and fuel performance. These physics are all coupled to some extent and are generally solved in a sequential but iterative fashion. The United States (U.S.) national laboratories have been developing MOOSE, an open source multiphysics framework since its inception at the Idaho National Laboratory (INL) in 2008. This framework enables seamless coupling of multiphysics simulations and facilitates the implementation of new physics and material governing laws. It is continuously expanded with novel numerical methods and new pre-implemented physics module. Numerous applications, developed within the Department of Energy (DOE) laboratories, academia, and industry, including outside of nuclear engineering, have been developed to study specialized physics problems. International collaborations are welcome on this open-source modeling and simulation project.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Finite-element-based simulations of electrodes for CO 2 cascade reduction reactions

The multielectron reduction of CO 2 to liquid fuels could be a path to scalable energy storage, but reaching this goal requires major advances in catalysis and systems engineering. Cascade catalysis, which couples sequential reactions without isolating intermediates, has emerged as a promising route to enhance selectivity and efficiency in CO 2 reduction (CO 2 R). In this review, we examine how finite-element-based simulations of continuum model [finite element method (FEM)] approaches are being used to analyze and guide CO 2 R cascade systems. We first outline the fundamentals of cascade catalysis and recent advances in catalytic materials (metallic, molecular, and hybrid architectures). We then focus on FEM developments at the electrode and device scales, emphasizing how these models capture transport phenomena, local microenvironments, and geometry-dependent effects. To clarify design principles, we present case studies of cascade electrodes organized in systems without and with integrated semiconductors. We further emphasize the integration of FEM with multiscale frameworks (density functional theory, molecular dynamics, kinetic Monte Carlo) and its role in bridging atomic-level insights with device-level performance. Finally, we identify current limitations and future prospects, including improved boundary conditions, coupling with operando experiments, and machine learning-accelerated model development. Together, these insights provide design principles for next-generation CO 2 R cascade systems for efficient solar fuel production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Irradiation of Advanced Cladding Specimens in the High Flux Isotope Reactor: Capsule Designs and Test Matrix

The Advanced Fuels Campaign (AFC) has initiated the Advanced Reactor Cladding (ARC) irradiation campaign to generate irradiation performance data for candidate fuel cladding concepts. The campaign includes a diverse set of ferritic/martensitic steels, oxide dispersion strengthened (ODS) alloys, FeCrAlbased alloys, coated materials, and welded cladding specimens produced through multiple US Department of Energy (DOE) programs and international collaborations. Three complementary experimental thrusts comprise the campaign: tensile testing (ARC Tensile) to rapidly screen candidate alloys, fracture toughness testing (ARC Fracture) to evaluate irradiation effects on crack resistance, and tubular weld testing (ARC Weld) to quantify irradiation-induced changes in the mechanical performance of end cap welds. This report documents the irradiation campaign design, including the selected materials, specimen types, irradiation matrix, and capsule designs for irradiation within the High Flux Isotope Reactor (HFIR). A total of 14 irradiation capsules were developed to achieve target irradiation temperatures between 300°C and 600°C and doses up to 30 dpa. Thermal analyses were performed using finite element methods to establish capsule geometries capable of achieving the desired specimen temperatures while accommodating differences in specimen geometry and material properties. The resulting capsule designs provide the basis for irradiation of the AFC-ARC experimental matrix and subsequent post-irradiation examination to assess the effects of neutron irradiation on advanced cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗