Search NASA⌕ Search

SEARCH · Search NASA

Results for “Florida Tech”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Florida Tech CubeSat Experiment Feasibility Study

CubeSats are a relatively new type of satellite. Smaller than long-term (5+ year life expectancy) satellites, these pico-satellites are comparatively cheap, small (10x10x10 cm), and are very versatile. Universities world-wide are using CubeSats to conduct a variety of experiments in space without the need for a large experimental platform. Today CubeSats are considered to be one of the most effective ways to send a small payload into space and has attracted the attention of many educational and non-profit organizations. As this pico-satellite model continues to gain penetration into the satellite build and launch industry, it is expected that more governmental, educational, and commercial interests will emerge. As an example, more of the space-related items of high interest to the National Science Foundation may be tackled with a CubeSat platform resulting in lower life cycle costs than traditional satellite options. NASA LSP, in cooperation with the Florida Institute of Technology, has initiated a feasibility study to investigate the technical aspects of measuring and transferring vibration, acceleration, temperature, and video data from a CubeSat to NASA Hanger AE on Cape Canaveral Air Force Station (CCAFS) a.k.a. Kennedy Space Center (KSC). This report provides a technical feasibility analysis to determine whether-or-not a specific set of NASA/LSP requirements can be accomplished. Our approach has been to provide a "notional" component layout to determine the feasibility of the NASA/LSP stakeholder requirements. The notional layout is used to consider component level technical issues such as size, weight, & power (SWaP), bandwidth, and other critical technical parameters. Even though the notional components may satisfy the stated requirements and thereby demonstrate feasibility, the notional layout is NOT considered a design since no component optimization and design trade-off analysis has taken place. This activity should be accomplished in an appropriate design phase that is outside of the scope of this effort.

Arrasmith, William W.↗
NASA NTRS2009

NASA's Impact in Florida: A Tech Transfer Perspective

The Innovative Partnerships Program (IPP) Office at NASA's Kennedy Space Center is dedicated to forming partnerships that can positively contribute to -- and benefit from -- NASA's research and development (R&D) and technology innovations. This document discusses the IPP-driven impacts of NASA in Florida.

Dunn, Carol↗
NASA NTRS1994

JOVE NASA-FIT program: Microgravity and aeronomy projects

This semi-annual status report is divided into two sections: Scanning Tunneling Microscopy Lab and Aeronomy Lab. The Scanning Tunneling Microscopy (STM) research involves studying solar cell materials using the STM built at Florida Tech using a portion of our initial Jove equipment funding. One result of the participation in the FSEC project will be to design and build an STM system which is portable. This could serve as a prototype STM system which might be used on the Space Shuttle during a Spacelab mission, or onboard the proposed Space Station. The scanning tunneling microscope is only able to image the surface structure of electrically conductive crystals; by building an atomic force microscope (AFM) the surface structure of any sample, regardless of its conductivity, will be able to be imaged. With regards to the Aeronomy Lab, a total of four different mesospheric oxygen emission codes were created to calculate the intensity along the line of sight of the shuttle observations for 2972A, Herzberg I, Herzberg II, and Chamberlain bands. The thermosphere-ionosphere coupling project was completed with two major accomplishments: collection of 500 data points on modulation of neutral wind with geophysical variables, and establishment of constraints on behavior of the height of the ionosphere as a result of interaction between geophysical and geometrical factors. The magnetotail plasma project has been centered around familiarization with the subject in the form of a literature search and preprocessing of IMP-8 data.

Patterson, James D.↗
NASA NTRS2016

Crawler Solids Unknown Analysis

Crawler Transporter (CT) #2 has been undergoing refurbishment to carry the Space Launch System (SLS). After returning to normal operation, multiple filters of the gear box lubrication system failed/clogged and went on bypass during a test run to the launch pad. Analysis of the filters was done in large part with polarized light microscopy (PLM) to identify the filter contaminates and the source of origin.

Polarized Light Microscopy↗
NASA NTRS2015

NASA Work Experience

I have had the opportunity to support the analytical laboratories in chemical analysis of unknown samples, using Optical Microscopy (OM), Polarizing Light Microscopy (PLM), Fourier-Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy with Energy Dispersive Spectroscopy (SEMEDS), and X-ray Powder Diffraction (XPD). I have assisted in characterizing fibers pulled from a spacecraft, a white fibrous residue discovered in a jet refueler truck, brown residue from a plant habitat slated for delivery to the ISS (International Space Station), corrosion on a pipe from a sprinkler, and air filtration material brought back from the ISS. I also conducted my own fiber study in order to practice techniques and further my understanding of background concepts. Furthermore, I had the opportunity to participate in diverse work assignments, where I was assigned to work with other branches of the engineering department for 1-2 days each. The first was in the Materials Science branch where I participated in the construction of the plant habitat intended for use in research aboard the ISS. The second was in the Testing Design branch where I assisted with tensile and hardness testing of over 40 samples. In addition, I have had the privilege to attend multiple tours of the NASA KSC campus, including to the Astronaut Crew Quarters, the VAB (the main area, the Columbia room, and the catwalk), the Visitor Center housing the shuttle Atlantis, the Saturn-V exhibit, the Prototype laboratory, SWAMP WORKS, the Shuttle Landing Facility, the Crawler, and the Booster Fabrication Facility (BFF). Lastly, much of my coursework prepared me for this experience, including numerous laboratory courses with topics diverse as chemistry, physics, and biology.

Florida Tech↗
DOE OSTI2025

Surrogate Constructed Scalable Circuits ADAPT-VQE in the Schwinger model

Inspired by recent advancements of simulating periodic systems on quantum computers, we develop a new approach, (SC)$^2$-ADAPT-VQE, to further advance the simulation of these systems. Our approach extends the scalable circuits ADAPT-VQE framework, which builds an ansatz from a pool of coordinate-invariant operators defined for arbitrarily large, though not arbitrarily small, volumes. Our method uses a classically tractable ``Surrogate Constructed'' method to remove irrelevant operators from the pool, reducing the minimum size for which the scalable circuits are defined. Bringing together the scalable circuits and the surrogate constructed approaches forms the core of the (SC)$^2$ methodology. Our approach allows for a wider set of classical computations, on small volumes, which can be used for a more robust extrapolation protocol. While developed in the context of lattice models, the surrogate construction portion is applicable to a wide variety of problems where information about the relative importance of operators in the pool is available. As an example, we use it to compute properties of the Schwinger model - quantum electrodynamics for a single, massive fermion in $1+1$ dimensions - and show that our method can be used to accurately extrapolate to the continuum limit.

Gustafson, Erik [RIACS, Mtn. View] (ORCID:00000001↗
DOE OSTI2025

Real Time, In-line Monitoring of Hanford Tank Wastes - Year 1 Report

The team comprised of students, postdocs, early, mid and senior career scientists from Los Alamos National Laboratory, Savanah River National Laboratory, Georgia Tech and Florida International University, with the guidance of H2C, is developing a suite of in-line instruments for the Hanford high level waste (HLW) and low active waste (LAW) processes to provide near-real-time analysis of waste form physical properties and composition. The work builds on results from the recent DOE-ORP, EM Technology Development and other projects that demonstrated promise for the use of real-time in-line monitoring (RTIM) to measure chemical compositions of slurries of up to 20 weight % solids. The goal is for this instrument suite is to substantially reduce the need for sampling for process control. Sample waste, exposure associated with sample analysis, and the demand for an external laboratory facility would be greatly reduced. The throughput of waste treatment systems would be improved by elimination of the downtime caused by waiting for sample results. This translates into reduced process storage as process knowledge will be continuously updated in near-real-time. These breakthrough technologies would significantly reduce the life cycle cost and accelerate the schedule for the Hanford tank waste mission.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2016

Polarized Light Microscopy

Polarized light microscopy (PLM) is a technique which employs the use of polarizing filters to obtain substantial optical property information about the material which is being observed. This information can be combined with other microscopy techniques to confirm or elucidate the identity of an unknown material, determine whether a particular contaminant is present (as with asbestos analysis), or to provide important information that can be used to refine a manufacturing or chemical process. PLM was the major microscopy technique in use for identification of materials for nearly a century since its introduction in 1834 by William Fox Talbot, as other techniques such as SEM (Scanning Electron Microscopy), FTIR (Fourier Transform Infrared spectroscopy), XPD (X-ray Powder Diffraction), and TEM (Transmission Electron Microscopy) had not yet been developed. Today, it is still the only technique approved by the Environmental Protection Agency (EPA) for asbestos analysis, and is often the technique first applied for identification of unknown materials. PLM uses different configurations in order to determine different material properties. With each configuration additional clues can be gathered, leading to a conclusion of material identity. With no polarizing filter, the microscope can be used just as a stereo optical microscope, and view qualities such as morphology, size, and number of phases. With a single polarizing filter (single polars), additional properties can be established, such as pleochroism, individual refractive indices, and dispersion staining. With two polarizing filters (crossed polars), even more can be deduced: isotropy vs. anisotropy, extinction angle, birefringence/degree of birefringence, sign of elongation, and anomalous polarization colors, among others. With the use of PLM many of these properties can be determined in a matter of seconds, even for those who are not highly trained. McCrone, a leader in the field of polarized light microscopy, often advised, If you cant determine a specific optical property of a particle after two minutes, move onto another configuration. Since optical properties can be seen so very quickly and easily under polarized light, it is only necessary to spend a maximum of two minutes on a technique to determine a particular property, though often only a few seconds are required.

Engineering↗
NASA NTRS1999

An Acoustic Charge Transport Imager for High Definition Television

This project, over its term, included funding to a variety of companies and organizations. In addition to Georgia Tech these included Florida Atlantic University with Dr. William E. Glenn as the P.I., Kodak with Mr. Mike Richardson as the P.I. and M.I.T./Polaroid with Dr. Richard Solomon as the P.I. The focus of the work conducted by these organizations was the development of camera hardware for High Definition Television (HDTV). The focus of the research at Georgia Tech was the development of new semiconductor technology to achieve a next generation solid state imager chip that would operate at a high frame rate (I 70 frames per second), operate at low light levels (via the use of avalanche photodiodes as the detector element) and contain 2 million pixels. The actual cost required to create this new semiconductor technology was probably at least 5 or 6 times the investment made under this program and hence we fell short of achieving this rather grand goal. We did, however, produce a number of spin-off technologies as a result of our efforts. These include, among others, improved avalanche photodiode structures, significant advancement of the state of understanding of ZnO/GaAs structures and significant contributions to the analysis of general GaAs semiconductor devices and the design of Surface Acoustic Wave resonator filters for wireless communication. More of these will be described in the report. The work conducted at the partner sites resulted in the development of 4 prototype HDTV cameras. The HDTV camera developed by Kodak uses the Kodak KAI-2091M high- definition monochrome image sensor. This progressively-scanned charge-coupled device (CCD) can operate at video frame rates and has 9 gm square pixels. The photosensitive area has a 16:9 aspect ratio and is consistent with the "Common Image Format" (CIF). It features an active image area of 1928 horizontal by 1084 vertical pixels and has a 55% fill factor. The camera is designed to operate in continuous mode with an output data rate of 5MHz, which gives a maximum frame rate of 4 frames per second. The MIT/Polaroid group developed two cameras under this program. The cameras have effectively four times the current video spatial resolution and at 60 frames per second are double the normal video frame rate.

Hunt, William D.↗
NASA NTRS1996

Observations and Analysis of Atmospheric Hydroxyl

Ground-based measurements of sunlight absorption at the OH P(sub 1)(l) resonance line at 308 nm have been made on a continuous basis at Fritz Peak, Colorado. The derived OH vertical column abundances show the persistence of a new seasonal regime which began in 1991. The fall minimum has been consistently depressed about 10-15% below the 1980-1990 average fall values. While the initial onset of depressed fall abundances occurred a few months after the Pinatubo eruption, there has been no fall OH recovery correlating with decreased amounts of volcanic aerosol found since spring 1993. The Colorado data also continues to exhibit an AM-PM asymmetry which varies seasonally, approximately in phase with local total ozone. These observations were presented at the Front Range AGU meeting in February 1996 and were published in Geophysical Research Letters in July 1996 (preprint enclosed). An update through the fall of 1996, when morning abundances were found to be extremely low, was presented at the Fall 1996 AGU meeting (abstract attached). A PEPSIOS instrument of identical design is currently operational and has been used since April 1996 for OH column measurements at New Mexico Tech, Socorro, NM. Title for both instruments was transferred from Florida Atlantic University to New Mexico Tech in February of 1996. Comparative measurements from the two instruments for April-July 1996 indicate small differences in OH column abundances, with New Mexico (34 deg N) abundances about 10% above Colorado (40 deg N) values for comparable solar zenith angles. A more detailed comparison will require at least one full year of data from both locations. New Mexico measurements were obtained on June 10, 1996, concurrently with a balloon launch of the NASA STRAT mission from Fort Sumner, New Mexico. We hope to make use of STRAT measurements H2O, CH4, and O3 which are particularly relevant to OH photochemistry. Additional work at New Mexico Tech involves a comparison of P(sub 1)(1) and Q(sub 1)(3) absorption by the method of Doppler shift of solar limb spectra. These are being used to infer path weighted temperatures and for validations studies on the standard method of analysis using the single P(sub 1)(1) line. Results were presented at the Fall 1996 AGU meeting (abstract attached). A graduate student in the Physics Department at New Mexico Tech has been supported since August 1996. The student is investigating column OH behavior using the NCAR 2-D model of the middle atmosphere. Graduate student support was not available until the start of the second year (Nov. 15, 1996), therefore funds have been transferred from the allocation for the research associate, who resigned from the project July 1, 1996.

Minschwaner, Ken R.↗
NASA NTRS2011

Camp Blanding Lightning Mapping Array

A seven station, short base-line Lightning Mapping Array was installed at the Camp Blanding International Center for Lightning Research and Testing (ICLRT) during April 2011. This network will support science investigations of Terrestrial Gamma-Ray Flashes (TGFs) and lightning initiation using rocket triggered lightning at the ICLRT. The network operations and data processing will be carried out through a close collaboration between several organizations, including the NASA Marshall Space Flight Center, University of Alabama in Huntsville, University of Florida, and New Mexico Tech. The deployment was sponsored by the Defense Advanced Research Projects Agency (DARPA). The network does not have real-time data dissemination. Description, status and plans will be discussed.

Blakeslee,Richard↗
DOE OSTI2026

Strain-Driven Evolution of Structural and Carrier Recombination Dynamics in Germanium

Strain engineering in group-IV semiconductors, in particular germanium (Ge), offers a promising route for advancing next-generation optoelectronic device performance. High minority carrier lifetime serves as a direct indicator of superior material quality and device efficiency. Several factors govern the minority carrier lifetime in both strained Ge and strained GeSn, such as strain level, epilayer thickness, defects, surface roughness, and Sn alloying. In this study, the impact of biaxial strain on effective minority carrier lifetimes of tensile-strained Ge (0% ..epsilon..-Ge/Al?As, 0.78% ..epsilon..-Ge/In0.115?Ga0.885?As, and 0.93% ..epsilon..-Ge/In0.16?Ga0.84?As) and compressively strained GeSn (-0.53% c-Ge0.97?Sn0.03/Al?As) epilayers, grown by molecular beam epitaxy, was experimentally investigated via the microwave-reflection photoconductive decay (..mu..-PCD) technique as a simultaneous function of thickness and strain. The structural and strain-relaxation properties were analyzed by high-resolution x-ray diffraction and Raman spectroscopy, while surface morphology analysis using atomic force microscopy provided insights into the surface roughness of strained Ge-based epilayers. Defect characterization by cross-section transmission electron microscopy revealed superior crystalline quality of ..epsilon..-Ge in one epilayer, while twin boundary formation was observed in the other. We investigated the carrier recombination dynamics in epitaxially strained Ge by extracting the bulk recombination lifetime and surface recombination velocity using the thickness-dependent minority carrier lifetime. High effective minority carrier lifetimes of approximately 60-340 ns were achieved at high strain levels with minimal dependence on the thickness of the strained Ge-based epilayers by means of the ..mu..-PCD technique. Minority carrier lifetimes in Ge-based epilayers exhibit a quadratic dependence on the biaxial strain, ranging from -0.88% (compressive) to +1.6% (tensile). The analysis of the carrier recombination dynamics in strained Ge-based heterostructures offers a pathway to designing group-IV based optoelectronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Home Insulation With the Stroke of a Brush

Hy-Tech Thermal Solutions, LLC, of Melbourne, Florida, is producing a very complex blend of ceramic vacuum-filled refractory products designed to minimize the path of hot air transfer through ceilings, walls, and roofs. The insulating ceramic technology blocks the transfer of heat outward when applied to paint on interior walls and ceilings, and prevents the transfer of heat inward when used to paint exterior walls and roofs, effectively providing year-round comfort in the home. As a manufacturer and marketer of thermal solutions for residential, commercial, and industrial applications, Hy-Tech Thermal Solutions attributes its success to the high performance insulating ceramic microsphere originally developed from NASA thermal research at Ames Research Center. Shaped like a hollow ball so small that it looks as if it is a single grain of flour to the naked eye (slightly thicker than a human hair), the microsphere is noncombustible and fairly chemical-resistant, and has a wall thickness about 1/10 of the sphere diameter, a compressive strength of about 4,000 pounds per square inch, and a softening point of about 1,800 C. Hy-Tech Thermal Solutions improved upon these properties by removing all of the gas inside and creating a vacuum. In effect, a 'mini thermos bottle' is produced, acting as a barrier to heat by reflecting it away from the protected surface. When these microspheres are combined with other materials, they enhance the thermal resistance of those materials. In bulk, the tiny ceramic 'beads' have the appearance of a fine talcum powder. Their inert, nontoxic properties allow them to mix easily into any type of paint, coating, adhesive, masonry, or drywall finish. Additionally, their roundness causes them to behave like ball bearings, rolling upon each other, and letting the coatings flow smoothly. When applied like paint to a wall or roof, the microsphere coating shrinks down tight and creates a dense film of the vacuum cells. The resulting ceramic layer improves fire resistance, protects from ultraviolet rays, repels insects such as termites, and shields from the destructive forces of nature.

Source record↗
NASA NTRS2025

Converter Compressor Building, SWMU 089 Monitoring Well 21 Area Implementation Work Plan Kennedy Space Center, Florida

This Implementation Work Plan (IWP) was prepared by Tetra Tech, Inc., for the National Aeronautics and Space Administration (NASA) under Indefinite Delivery Indefinite Quantity (IDIQ) Contract 80KSC019D0011/80KSC019F0070, for the implementation of a bioremediation Interim Measure (IM) at the Converter Compressor Building (CCB) site located at Kennedy Space Center (KSC), Florida. The location of CCB within KSC is shown on Figure A-1. CCB has been designated as Solid Waste Management Unit (SWMU) 089 under KSC’s Resource Conservation and Recovery Act (RCRA) Corrective Action Program. The overall Corrective Action Objective (CAO) for CCB is to reduce concentrations of trichloroethene (TCE), cis-1,2-dichloroethene (cDCE), trans-1,2-dichloroethene (tDCE), and vinyl chloride (VC) to less than State of Florida Groundwater Cleanup Target Levels (GCTLs). The objective for the IM associated with this IM is to reduce groundwater concentrations for the contaminants of concern (COCs) to less than their Natural Default Attenuation Concentrations (NADCs) within the Monitoring Well 21 Area (herein referred to as MW21 Area) via bioremediation injections to support transition to long term monitoring (LTM). This IWP describes the activities that will be performed for the treatment of the MW21 Area. The Revision 1 CCB MW21 Area Interim Measure Work Plan (IMWP; NASA, 2024), which was approved by the Florida Department of Environmental Protection (FDEP) on December 26, 2024, was used as the design basis for this IWP.

Mark Jonnet↗
DOE OSTI2024

Upper Limit on the Photoproduction Cross Section of the Spin-Exotic $π$ 1 (1600)

Here, the spin-exotic hybrid meson π 1 (1600) is predicted to have a large decay rate to the ωππ final state. Using 76.6 pb -1 of data collected with the GlueX detector, we measure the cross sections for the reactions γp → ωπ + π - p, γp → ωπ 0 π 0 p, and γp → ωπ - π 0 Δ ++ in the range E γ = 8 - 10 GeV. Using isospin conservation, we set the first upper limits on the photoproduction cross sections of the π$^0_1$(1600) and $π^-_1$(1600). We combine these limits with lattice calculations of decay widths and find that photoproduction of η' π is the most sensitive two-body system to search for the π 1 (1600).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Fossil Energy in the Hydrogen Economy – A Carbon-Water-Energy Nexus Adaptive Evaluation Platform

This project develops tools to evaluate fossil energy within the hydrogen economy. In particular, the project seeks to explore the Carbon-Water-Energy Nexus and develop adaptive evaluation tools. The primary goal of this project was to evaluate fossil-based hydrogen production methods with an emphasis on their sustainability, particularly with respect to carbon emissions and water use. The overall technical objectives that guided this evaluation consisted of 1) technology assessment, which sought to establish a comprehensive baseline of existing and emerging technologies for the generation, transportation, storage, and end use of hydrogen derived from fossil fuels, 2) carbon footprint analysis through quantification and analysis of carbon emissions associated with these hydrogen technologies, and identification of novel strategies and technologies that can effectively mitigate the carbon footprint, 3) water intensity assessment by evaluating the water needs (water-energy nexus) associated with different fossil fuel-based hydrogen technologies and proposing strategies to reduce water use, thus ensuring sustainable resource management, and 4) review of regulatory, policy and economic trends were examined to provide an overview of the factors influencing the adoption and integration of fossil fuel-derived hydrogen technologies into current energy markets. Beyond the technical outcomes, this project contributed to 5) education and workforce development through targeted training and educational opportunities for engineering students, preparing the next generation of professionals with technical, economic, and regulatory expertise in the hydrogen economy. Ultimately, this effort was intended to train the future workforce to provide useful insights to policymakers, industry stakeholders, and the broader energy community to facilitate informed decisions and responsible development within the hydrogen economy.

08 HYDROGEN↗
NASA NTRS2016

Hypergol Maintenance Facility Hazardous Waste South Staging Areas, SWMU 070 Corrective Measures Implementation

This document presents the Corrective Measures Implementation (CMI) Year 10 Annual Report for implementation of corrective measures at the Hypergol Maintenance Facility (HMF) Hazardous Waste South Staging Areas at Kennedy Space Center, Florida. The work is being performed by Tetra Tech, Inc., for the National Aeronautics and Space Administration (NASA) under Indefinite Delivery Indefinite Quantity (IDIQ) NNK12CA15B, Task Order (TO) 07. Mr. Harry Plaza, P.E., of NASA's Environmental Assurance Branch is the Remediation Project Manager for John F. Kennedy Space Center. The Tetra Tech Program Manager is Mr. Mark Speranza, P.E., and the Tetra Tech Project Manager is Robert Simcik, P.E.

CMI↗