Search NASA⌕ Search

SEARCH · Search NASA

Results for “Freeze tape cast cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Freeze Tape Casting Electrode with Bilayered Architecture for High-Performance Lithium-Ion Batteries

A facile freeze tape casting (FTC) strategy is utilized to prepare bilayered 4 mAh cm –2 high-loading LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathodes. The bottom layer is a conventional nonaqueous electrode, which has a dense structure for high-energy purposes. Further, the top layer is prepared by the proposed FTC, exhibiting a porous feature for high-power requirement. With the assistance of FTC, the bilayered electrodes successfully deliver enhanced rate and cyclic performance due to the improved lithium-ion diffusion kinetics and pathways. Therefore, the proposed FTC strategy and its delivered electrodes are promising for energy- and power-density lithium-ion batteries, potentially enlightening the research and development of lithium-ion battery manufacturing.

25 ENERGY STORAGE↗
NASA NTRS2014

Method for Making a Fuel Cell from a Solid Oxide Monolithic Framework

The invention is a novel solid oxide fuel cell (SOFC) stack comprising individual bi-electrode supported fuel cells in which a thin electrolyte is supported between electrodes of essentially equal thickness. Individual cell units are made from graded pore ceramic tape that has been created by the freeze cast method followed by freeze drying. Each piece of graded pore tape later becomes a graded pore electrode scaffold that subsequent to sintering, is made into either an anode or a cathode by means of appropriate solution and thermal treatment means. Each cell unit is assembled by depositing of a thin coating of ion conducting ceramic material upon the side of each of two pieces of tape surface having the smallest pore openings, and then mating the coated surfaces to create an unsintered electrode scaffold pair sandwiching an electrolyte layer. The opposing major outer exposed surfaces of each cell unit is given a thin coating of electrically conductive ceramic, and multiple cell units are stacked, or built up by stacking of individual cell layers, to create an unsintered fuel cell stack. Ceramic or glass edge seals are installed to create flow channels for fuel and air. The cell stack with edge sealants is then sintered into a ceramic monolithic framework. Said solution and thermal treatments means convert the electrode scaffolds into anodes and cathodes. The thin layers of electrically conductive ceramic become the interconnects in the assembled stack.

Cable, Thomas L.↗
NASA NTRS2014

Method for Making a Fuel Cell

The invention is a novel solid oxide fuel cell (SOFC) stack comprising individual bi-electrode supported fuel cells in which an electrolyte layer is supported between porous electrodes. The porous electrodes may be made from graded pore ceramic tape that has been created by the freeze cast method followed by freeze-drying. Each piece of graded pore tape later becomes a graded pore electrode scaffold that, subsequent to sintering, is made into either an anode or a cathode. The electrode scaffold comprising the anode includes a layer of liquid metal. The pores of the electrode scaffolds gradually increase in diameter as the layer extends away from the electrolyte layer. As a result of this diameter increase, any forces that would tend to pull the liquid metal away from the electrolyte are reduced while maintaining a diffusion path for the fuel. Advantageously, the fuel cell of the invention may utilize a hydrocarbon fuel without pre-processing to remove sulfur.

Cable, Thomas L.↗
NASA NTRS2009

Symmetrical, bi-electrode supported solid oxide fuel cell

The present invention is a symmetrical bi-electrode supported solid oxide fuel cell comprising a sintered monolithic framework having graded pore electrode scaffolds that, upon treatment with metal solutions and heat subsequent to sintering, acquire respective anodic and cathodic catalytic activity. The invention is also a method for making such a solid oxide fuel cell. The graded pore structure of the graded pore electrode scaffolds in achieved by a novel freeze casting for YSZ tape.

Cable, Thomas L.↗
DOE OSTI2025

Optimization of catholyte for halide-based all-solid-state batteries

Halide solid electrolytes gain significant attention due to their high ionic conductivity, low processing temperature, dry air compatibility, and high-voltage stability. However, low cathode active material (CAM) loading in the composite cathode constrains the realization of high energy density for halide-based all-solid-state batteries. In this study, three halide materials, raw Li 3 YBrCl 5 (LYBC-R, <30μm), milled LYBC (LYBC-M, <5 μm) and freeze-dried Li 3 InCl 6 (LIC, <500 nm), were used as catholytes, combined with LYBC-M as the electrolyte and LiIn alloy as the anode. The CAM:catholyte ratio was investigated as well as stack pressure and operating temperature. Our study demonstrates that particle size of the catholyte plays an important role only for high CAM loading or high C-rate cycling. At moderate CAM loading (65 and 70wt% LiNi 0.83 Mn 0.06 Co 0.11 O 2 ) and 0.1 C-rate, all the three catholytes perform well, providing initial discharge capacities >177 mAh/g. At high CAM loading (85wt%) and 0.1 C-rate, a cathode with the nano-scale LIC catholyte provides discharge capacity of 175 mAh/g, while the larger particle size catholytes suffer significantly reduced capacity. Both LYBC and LIC catholytes provided capacity retention >80% after 200 cycles at 0.5C. These results imply that cathode particle size is critically important for performance at high CAM loading. Furthermore, both electrolyte and cathode were tape cast to scale up size and prepare realistic layer thicknesses. A small amount of binder was used in both layers, to balance the electrochemical performance and mechanical properties. Further, the discharge capacity of a tape cell was 152mA h/g at 0.1C with a capacity retention of 81.8% after 20 cycles at 0.5C. The results demonstrate the excellent performance of LYBC as an electrolyte, and provide guidance for halide-based cathode design.

25 ENERGY STORAGE↗