Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Cycle Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Linear quadratic stationkeeping on travelling ellipses

An automatic controller for Space Shuttle stationkeeping or formationkeeping is presented. The controller, which is a candidate for future on-orbit autopilot enhancement, uses a fuel 'optimized' limit cycle trajectory in a feedforward loop for precise control at nonequilibrium set points. Disturbance rejection is accomplished by a discrete time, linear quadratic regulator, which is employed for tracking of the feedforward model. Feedback gain selection is done to provide good limit cycling performance and low fuel consumption. Velocity correlations are carried out by use of a pseudo 6 degree-of-freedom jet selection scheme. Results indicate that 20 ft precision can be achieved using current sensors.

Adams, Neil J.↗

Modeling of High Speed Reacting Flows: Established Practices and Future Challenges

Computational fluid dynamics (CFD) has proven to be an invaluable tool for the design and analysis of high- speed propulsion devices. Massively parallel computing, together with the maturation of robust CFD codes, has made it possible to perform simulations of complete engine flowpaths. Steady-state Reynolds-Averaged Navier-Stokes simulations are now routinely used in the scramjet engine development cycle to determine optimal fuel injector arrangements, investigate trends noted during testing, and extract various measures of engine efficiency. Unfortunately, the turbulence and combustion models used in these codes have not changed significantly over the past decade. Hence, the CFD practitioner must often rely heavily on existing measurements (at similar flow conditions) to calibrate model coefficients on a case- by-case basis. This paper provides an overview of the modeled equations typically employed by commercial- quality CFD codes for high-speed combustion applications. Careful attention is given to the approximations employed for each of the unclosed terms in the averaged equation set. The salient features (and shortcomings) of common models used to close these terms are covered in detail, and several academic efforts aimed at addressing these shortcomings are discussed.

Baurle, R. A.↗

Performance potential of an advanced technology Mach 3 turbojet engine installed on a conceptual high-speed civil transport

The performance of an advanced technology conceptual turbojet optimized for a high-speed civil aircraft is presented. This information represents an estimate of performance of a Mach 3 Brayton (gas turbine) cycle engine optimized for minimum fuel burned at supersonic cruise. This conceptual engine had no noise or environmental constraints imposed upon it. The purpose of this data is to define an upper boundary on the propulsion performance for a conceptual commercial Mach 3 transport design. A comparison is presented demonstrating the impact of the technology proposed for this conceptual engine on the weight and other characteristics of a proposed high-speed civil transport. This comparison indicates that the advanced technology turbojet described could reduce the gross weight of a hypothetical Mach 3 high-speed civil transport design from about 714,000 pounds to about 545,000 pounds. The aircraft with the baseline engine and the aircraft with the advanced technology engine are described.

Morris, Shelby J., Jr.↗

Multipoint Design and Optimization of a Turboshaft Engine for a Tiltwing Turboelectric Vertical Takeoff Landing Air Taxi

This paper describes the design of a turboshaft engine for a tiltwing air taxi application. In this case, the tiltwing air taxi is intended to fly a 400 nm mission with up to fifteen passengers. Engine requirements for the concept engine are taken from aircraft system studies where thrust is produced by four propellers driven by electric motors and powered by a single gas turbine engine. The purpose of this paper is to perform a cycle design optimization that minimizes fuel consumption and weight while respecting current technology limitations to meet mission requirements. To achieve results, the engine overall pressure ratio and maximum temperature at the exit of the combustor are set as the design parameters. Several sensitivity studies are also performed to visualize optimization trends. Results of the optimization study show solutions are heavily dependent on engine cooling flow requirements and exact mission requirements. This engine is intended for use in large system optimization research.

gas turbine↗

Multi-Point Design and Optimization of a Turboshaft Engine for a Tiltwing Turboelectric VTOL Air Taxi

This paper describes the design of a turboshaft engine for a tiltwing air taxi application. In this case, the tiltwing air taxi is intended to fly a 400-nautical mile mission with up to fifteen passengers. Engine requirements for the concept engine are taken from aircraft system studies where thrust is produced by four propellers driven by electric motors and powered by a single gas turbine engine. The purpose of this paper is to perform a cycle design optimization that minimizes fuel consumption and weight while respecting current technology limitations to meet mission requirements. To achieve results, the engine overall pressure ratio and maximum temperature at the exit of the combustor are set as the design parameters. Several sensitivity studies are also performed to visualize optimization trends. Results of the optimization study show solutions are heavily dependent on engine cooling flow requirements and exact mission requirements. This engine is intended for use in large system optimization research.

Optimization↗

Performance Optimization of the Gasdynamic Mirror Propulsion System

Nuclear fusion appears to be a most promising concept for producing extremely high specific impulse rocket engines. Engines such as these would effectively open up the solar system to human exploration and would virtually eliminate launch window restrictions. A preliminary vehicle sizing and mission study was performed based on the conceptual design of a Gasdynamic Mirror (GDM) fusion propulsion system. This study indicated that the potential specific impulse for this engine is approximately 142,000 sec. with about 22,100 N of thrust using a deuterium-tritium fuel cycle. The engine weight inclusive of the power conversion system was optimized around an allowable engine mass of 1500 Mg assuming advanced superconducting magnets and a Field Reversed Configuration (FRC) end plug at the mirrors. The vehicle habitat, lander, and structural weights are based on a NASA Mars mission study which assumes the use of nuclear thermal propulsion' Several manned missions to various planets were analyzed to determine fuel requirements and launch windows. For all fusion propulsion cases studied, the fuel weight remained a minor component of the total system weight regardless of when the missions commenced. In other words, the use of fusion propulsion virtually eliminates all mission window constraints and effectively allows unlimited manned exploration of the entire solar system. It also mitigates the need to have a large space infrastructure which would be required to support the transfer of massive amounts of fuel and supplies to lower a performing spacecraft.

Emrich, William J., Jr.↗

Multidisciplinary Optimization of A Transonic Truss-Braced Wing Aircraft Using Aviary

The continuous push to decrease fuel burn of single-aisle commercial aircraft has led to interest in a Transonic Truss-Braced Wing (TTBW) concept vehicle. Sporting high-slung wings that are long and slender to increase aerodynamic efficiency, a TTBW can also accommodate higher-bypass turbine engines. The combination of these two changes potentially leads to an overall decrease in fuel consumption. In this paper, a TTBW concept vehicle is assembled in the Aviary open-source tool for conceptual aircraft design. The conceptual-level aerodynamics and propulsion systems that come prepackaged with Aviary are replaced with higher-fidelity vortex lattice method for aerodynamics (VSPAERO) and a one-dimensional cycle analysis tool for propulsion (pyCycle). The vehicle is then optimized to minimize fuel burn for a representative commercial mission. Design parameters for the vehicle include the electrified turbine size, the size of the electric motors which are used for takeoff and climb assist, and battery capacity. The TTBW concept vehicle presented in this paper represents the first application of Aviary to an aircraft design problem.

Optimization↗

Evaluation of innovative rocket engines for single-stage earth-to-orbit vehicles

Computer models of rocket engines and single-stage-to-orbit vehicles that were developed by the authors at DFVLR and NASA have been combined. The resulting code consists of engine mass, performance, trajectory and vehicle sizing models. The engine mass model includes equations for each subsystem and describes their dependences on various propulsion parameters. The engine performance model consists of multidimensional sets of theoretical propulsion properties and a complete thermodynamic analysis of the engine cycle. The vehicle analyses include an optimized trajectory analysis, mass estimation, and vehicle sizing. A vertical-takeoff, horizontal-landing, single-stage, winged, manned, fully reusable vehicle with a payload capability of 13.6 Mg (30,000 lb) to low earth orbit was selected. Hydrogen, methane, propane, and dual-fuel engines were studied with staged-combustion, gas-generator, dual bell, and the dual-expander cycles. Mixture ratio, chamber pressure, nozzle exit pressure liftoff acceleration, and dual fuel propulsive parameters were optimized.

Manski, Detlef↗

Optimization of wave rotors for use as gas turbine engine topping cycles

Use of a wave rotor as a topping cycle for a gas turbine engine can improve specific power and reduce specific fuel consumption. Maximum improvement requires the wave rotor to be optimized for best performance at the mass flow of the engine. The optimization is a trade-off between losses due to friction and passage opening time, and rotational effects. An experimentally validated, one-dimensional CFD code, which includes these effects, has been used to calculate wave rotor performance, and find the optimum configuration. The technique is described, and results given for wave rotors sized for engines with sea level mass flows of 4, 26, and 400 lb/sec.

Wilson, Jack↗

Conceptual design of reduced energy transports

This paper reports the results of a conceptual design study of new, near-term fuel-conservative aircraft. A parametric study was made to determine the effects of cruise Mach number and fuel cost on the 'optimum' configuration characteristics and on economic performance. Supercritical wing technology and advanced engine cycles were assumed. For each design, the wing geometry was optimized to give maximum return on investment at a particular fuel cost. Based on the results of the parametric study, a reduced energy configuration was selected. Compared with existing transport designs, the reduced energy design has a higher aspect ratio wing with lower sweep, and cruises at a lower Mach number. It yields about 30% more seat-miles/gal than current wide-body aircraft. At the higher fuel costs anticipated in the future, the reduced energy design has about the same economic performance as existing designs.

Ardema, M. D.↗

Advanced 2030 Single Aisle Aircraft Modeling for the Electrified Powertrain Flight Demonstration Program

The NASA Electrified Powertrain Flight Demonstration Program is aimed at advancing electrified powertrains for future aircraft platforms through flight demonstrations for various passenger classes and power levels. The objective of this paper is to establish non-electrified reference models for 2030 aircraft with advanced technologies for the large single aisle (150 passenger) and small single aisle (100 passenger) vehicle classes. Current state-of-art aircraft are first identified and modeled using a proprietary design tool called Environmental Design Space. Next, through a comprehensive literature review, engine, airframe and composite material technologies that are expected to be available by 2030 are identified, and their respective benefits are applied to the 2030 vehicles. The engine cycle and the aircraft design are then optimized to provide the maximum fuel burn benefit while meeting all the specified aircraft requirements. While the large single aisle aircraft range requirement is kept the same as the current state-of-art aircraft, the small single aisle aircraft is optimized for a reduced range of 1000 nmi. Expected fuel burn benefit from these technologies along with any propulsive, aerodynamic and weight benefit will be summarized in this paper.

single aisle aircraft↗

Computerized systems analysis and optimization of aircraft engine performance, weight, and life cycle costs

The computational techniques are described which are utilized at Lewis Research Center to determine the optimum propulsion systems for future aircraft applications and to identify system tradeoffs and technology requirements. Cycle performance, and engine weight can be calculated along with costs and installation effects as opposed to fuel consumption alone. Almost any conceivable turbine engine cycle can be studied. These computer codes are: NNEP, WATE, LIFCYC, INSTAL, and POD DRG. Examples are given to illustrate how these computer techniques can be applied to analyze and optimize propulsion system fuel consumption, weight and cost for representative types of aircraft and missions.

Fishbach, L. H.↗

On variable hydrostatic transmission for road vehicles, powered by supply of fluid at constant pressure

Various hydrostatic power transmission systems for automotive applications with power supply at constant pressure and unrestricted flow and with a Volvo Flygmotor variable displacement motor as the principal unit were investigated. Two most promising concepts were analyzed in detail and their main components optimized for minimum power loss at the EPA Urban Driving Cycle. The best fuel consumption is less than 10 lit. per 100 kM for a 1542 kG vehicle with a hydrostatic motor and a two speed gear box in series (braking power not recovered). Realistic system pressure affects the fuel consumption just slightly, but the package volume/weight drastically. Back pressure increases losses significantly. Special attention was paid to description of the behavior and modeling of the losses of variable displacement hydrostatic machines.

Magi, M.↗

Rapid near-optimal aerospace plane trajectory generation and guidance

Problems associated with onboard trajectory optimization, propulsion system cycle selection, and the synthesis of guidance laws are addressed for ascent to low earth orbit of an airbreathing, single-stage-to-orbit vehicle. A multicycle propulsion system is assumed that incorporates turbojet, ramjet, scramjet, and rocket engines. An energy state approximation is applied to a singularly perturbed, four-state dynamic model for flight of a point mass over a spherical nonrotating earth. An algorithm is then derived for generating both the fuel-optimal climb profile and the guidance commands required to follow that profile. In particular, analytic switching conditions are derived that, under appropriate assumptions, efficiently govern optimal transition from one propulsion cycle to another. The algorithm proves to be computationally efficient and suitable for real-time implementation. The paper concludes with the presentation of representative numerical results that illustrate the nature of the fuel-optimal climb paths and the tracking performance of the guidance algorithm.

Corban, J. E.↗

Conceptual design study of an improved gas turbine powertrain

The conceptual design for an improved gas turbine (IGT) powertrain and vehicle was investigated. Cycle parameters, rotor systems, and component technology were reviewed and a dual rotor gas turbine concept was selected and optimized for best vehicle fuel economy. The engine had a two stage centrifugal compressor with a design pressure ratio of 5.28, two axial turbine stages with advanced high temperature alloy integral wheels, variable power turbine nozzle for turbine temperature and output torque control, catalytic combustor, and annular ceramic recuperator. The engine was rated at 54.81 kW, using water injection on hot days to maintain vehicle acceleration. The estimated vehicle fuel economy was 11.9 km/l in the combined driving cycle, 43 percent over the 1976 compact automobile. The estimated IGT production vehicle selling price was 10 percent over the comparable piston engine vehicle, but the improved fuel economy and reduced maintenance and repair resulted in a 9 percent reduction in life cycle cost.

Chapman, W. I.↗

Nonlinear Control of a Reusable Rocket Engine for Life Extension

This paper presents the conceptual development of a life-extending control system where the objective is to achieve high performance and structural durability of the plant. A life-extending controller is designed for a reusable rocket engine via damage mitigation in both the fuel (H2) and oxidizer (O2) turbines while achieving high performance for transient responses of the combustion chamber pressure and the O2/H2 mixture ratio. The design procedure makes use of a combination of linear and nonlinear controller synthesis techniques and also allows adaptation of the life-extending controller module to augment a conventional performance controller of the rocket engine. The nonlinear aspect of the design is achieved using non-linear parameter optimization of a prescribed control structure. Fatigue damage in fuel and oxidizer turbine blades is primarily caused by stress cycling during start-up, shutdown, and transient operations of a rocket engine. Fatigue damage in the turbine blades is one of the most serious causes for engine failure.

Lorenzo, Carl F.↗

Time Resolved Visualization of Liquid Jet Interaction With H2-Air Rotating Detonations Using MHz Rate Diesel PLIF

The characterization of the dynamic response of liquid jets to transient detonation wave passage is critical for optimization and modeling of liquid fueled rotating detonation combustors. In this work, a rotating detonation combustor (RDC) is operated on hydrogen and air to sustain stable detonation waves that acts as a detonation driver and interact in a one-way coupled manner with a single liquid fuel jet that propagates into the combustion chamber with cycle periods of ~ 250 μs. Diesel is utilized as a realistic fuel surrogate with higher aromatic compounds to enable fluorescence excitation, using the 355 nm thirdharmonic output of a burst-mode Nd:YAG laser, imaged at rates up to 1 MHz. By optimizing the technique to accommodate orders of magnitude variations in the fuel density throughout the injection process, the PLIF data enable quantitative measurements including the refill time, the relative recovery between liquid and gaseous jets and jet trajectory across various momentum flux ratio. As the passage of the detonation wave imparts significant changes in the momentum flux ratio, the qualitative liquid break-up process and spatial distribution varies significantly in time. As the injection system recovers ~ 70% of the cycle period and return to a quasi-steady position and allow comparisons with theoretical jet trajectories. These data, enabled by ultra-high-speed PLIF imaging, represent some of the first detailed measurements for quantifying the dynamic response and recovery of liquid jets exposed to periodic detonations in an operating RDC.

Propulsion↗