Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fusion reactors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Irradiation-induced gas production in REBCO-based magnet materials used for future compact fusion reactors

Nuclear fusion is an enticing alternative to current sources of energy, with multilayered Rare-Earth Barium Copper Oxide (REBCO) coated conductors deemed pivotal in the race toward fully realized, commercially viable, and magnetic confinement fusion reactors. In this study, we simulated the ion spectrum expected to evolve from REBCO's nickel-based Hastelloy C-276 substrate and copper stabilizer in an affordable robust compact-like reactor. We then emulated this gas production through helium implantation to investigate changes in materials and superconducting properties. Our results revealed that the substrate and stabilizer are capable of producing protons energetic enough to recoil throughout the tape thickness in appreciable doses, and alphas energetic enough to deposit 7.54 × 1014 ions/cm2 or 50.1 helium appm in the superconducting layer over a 30-year reactor lifetime. The superconducting layer of SuperPower® tapes exhibited at least double the swelling rate of the other major layers, and both SuperPower and Fujikura Ltd. tapes displayed microstructural changes in the REBCO layer not observed in isotropic metals. For the estimated lifetime fluence, the Fujikura tapes showed a ∼1 K reduction in critical temperature and a 32% degradation in critical current for compact reactor-relevant conditions (16 T, 20 K). Nuclear transmutation, low-temperature solder implantations, gas-ion evolution, the influence of gas production on vortex dynamics, and other related considerations are also discussed.

Reis, Chris↗
DOE OSTI2025

Demonstration of Super-X divertor exhaust control for transient heat load management in compact fusion reactors

Nuclear fusion could offer clean, abundant energy. However, managing the power exhausted from the core fusion plasma towards the reactor wall remains a major challenge. This is compounded in emerging compact reactor designs promising more cost-effective pathways towards commercial fusion energy. Alternative Divertor Configurations (ADCs) are a potential solution. In this work, we demonstrate exhaust control in ADCs, employing a novel method to diagnose the neutral gas buffer, which shields the target. Our work on the Mega Ampere Spherical Tokamak Upgrade shows that ADCs tackle key risks and uncertainties for fusion energy. Their highly reduced sensitivity to perturbations enables active exhaust control in otherwise unfeasible situations and facilitates an increased passive absorption of transients, which would otherwise damage the divertor. We observe a strong decoupling of each divertor from other reactor regions, enabling near-independent control of the divertors and core plasma. Our work showcases the real-world benefits of ADCs for effective heat load management in fusion power reactors.

Imaging techniques↗
DOE OSTI2025

History, present status, and future directions of vanadium alloys for fusion reactors

Since the need for low-activation fusion reactor materials was recognized in the mid-1980s, vanadium alloys have been researched and developed as promising candidates for blanket structural materials. Vanadium alloys are non-ferromagnetic and ductile materials and thus have advantages different from other candidates. However, since vanadium alloys are still at a premature industrial stage, research and development have been carried out not only on issues specific to fusion reactors but also on those related to industrial materials. Blankets using vanadium alloys as structural materials and liquid Li as a tritium breeder and coolant (self-cooled V/Li blankets) have unique characteristics, and research and development of issues specific to V/Li blankets have been conducted in conjunction with the development of vanadium alloys. In this paper, the progress of this research and development is reviewed, and the remaining issues are pointed out. As a result, the future direction of vanadium alloy research and development is discussed, considering recent changes in the environment surrounding fusion energy.

Liquid Li blanket↗
DOE OSTI2025

STORM: Scrape-off layer turbulence in tokamak fusion reactors

The scrape-off layer of a tokamak fusion reactor carries the plasma exhaust from the hot core plasma to the material surfaces of the reactor vessel. The heat loads imposed by the exhaust are a critical limit on the performance of fusion power plants. Turbulent transport of the plasma regulates the width of the scrape-off layer plasma and must be modelled to understand the intensity of these heat loads. STORM is a plasma turbulence code capable of simulating three dimensional turbulence across the full scrape-off layer of a tokamak fusion reactor, using a drift reduced, collisional fluid model. STORM uses mostly finite difference schemes, with a staggered grid in the direction parallel to the magnetic field. We describe the model, geometry and initialisation options used by STORM, as well as the numerical methods, which are implemented using the BOUT++ plasma simulation framework. BOUT++ has been enhanced alongside the development of STORM, providing better support for staggered grid methods. We summarise these enhancements, including a detailed explanation of the parallel derivative methods, which underwent a major update for version 4 of BOUT++.

BOUT++↗
DOE OSTI2024

Description of FY25 Theory and Simulation Performance Target: Development of an integrated modeling framework for fusion reactor design and assessment

The urgency to deliver fusion power is growing now more than ever, with increasing pressure for both public programs and private companies to meet milestones timelines and overcome significant remaining technical challenges to ensure growth of a nascent fusion industry in time to meet rapidly growing clean energy demands. With incredible advancements in computation and years of investment in fusion model development and validation, integrated modeling is poised to fill a key role in accelerating the timeline to a fusion pilot plant (FPP). Future fusion pilot plants will operate in regimes far beyond current experience, and device design will rely on physics-based prediction and extrapolation. Many concepts will also rely on simulation to assess safety (shielding, tritium management, materials activation and lifetimes), economics and scalability before the decision to build. Importantly, integrated simulation can be used to reveal and solve the complexities of system integration that may otherwise not be apparent in physical components or models developed in isolation. New experimental test facilities that produce relevant conditions to validate and resolve key technical challenges for various subsystems (materials, blankets, fuel cycle, etc.) have been repeatedly called for by the fusion community but are not yet realized. Integrated modeling has an important role in identifying realistic load conditions (thermal, electromagnetic, plasma, neutron and photon loads, etc.) and defining the components and experiments for these test facilities in order to ensure meaningful validation that sufficiently reduces modeling uncertainties and technical risk for the full integrated reactor. The Fusion REactor Design and Assessment (FREDA) SciDAC project is building a component-based integrated modeling framework & data structure to enable self-consistent, multi-fidelity, iterative optimization workflows for the fusion reactor design process. FREDA aims to shorten the time to viable designs by providing a set of flexible workflows to support the various stages of the design process using an integrated model hierarchy, ranging from the simple analytic descriptions to the highest fidelity, theory-based plasma and engineering modeling developed by the fusion and fission communities. These tools are expected to be needed for timely support of FPP design in the milestone program and in the FIRE collaboratives. The plasma simulation backbone of FREDA is IPS-FASTRAN with newly developed coupled Core-Edge Pedestal-SOL (CESOL) workflows, which is being extended to the far-SOL region up to the plasma facing components. FREDA incorporates the FERMI engineering modeling suite and will enable self-consistent evaluation of the thermal shields, limiters, blanket, magnets, and other surrounding structures with predictions of temperatures, erosion, dpa, activation, tritium generation and transport, creep, corrosion, material degradation, etc. Parametric generation of 3D CAD enables rapid iteration of component geometry in response to plasma and loading specifications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulation of Helium Flow Visualization Apparatus for Studies of Blanket Cooling in Fusion Reactors

Flow visualization is essential to understanding helium cooling performance. This article investigates helium flow visualization in an apparatus to support the design of the blanket first wall for a fusion reactor. Helium’s safety advantages make it an attractive coolant, but effective cooling and flow visualization remain challenging. Sophisticated simulations are conducted in different test sections to address three key areas in the design of a test apparatus and cooling channel enhancements: the influence of viewing glass windows on flow patterns, the impact of increased heating, and the effectiveness of cooling structures like baffles. Viewing glass windows introduce flow recirculation region bifurcation and flow asymmetry, affecting flow patterns and necessitating careful analysis in future experiments. Increased heating results in helium flow detachment from the heated surface, leading to hot spots. Cooling structures, particularly baffles, prove effective in maintaining consistent attachment to the heated surface, improving the heat transfer performance. Further, this study also examines a tunable parameter in the turbulence model, highlighting the importance of accurate model tuning for future fusion reactor cooling designs. With an imminent helium flow visualization facility, these simulations will be used to optimize cooling structures on the heated wall to improve flow attachment and heat transfer efficiency. This work serves as a first investigation of the helium flow visualization apparatus for blanket cooling enhancement in fusion reactor design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Experimental Setup to Investigate Hydrogen Isotope Retention on Powder Samples as Slag/Dust Proxies for Advanced Fusion Reactors

Slag/dust formation is one of the critical issues regarding tritium retention in advanced fusion reactors. We upgraded an ultrahigh vacuum device, the sample exposure station (SES), to perform temperature-programmed desorption (TPD), also known as thermal desorption spectroscopy, to investigate deuterium (D) retention in powder samples that are utilized as proxies for slag/dust particles formed in fusion reactors. TPD analysis, calibrated for the desorption rate, was successfully performed on commercially available crystalline/amorphous boron (B) powder after D 2 neutral gas or D + ion exposure. We calibrated the B powder temperature measurement for TPD analysis utilizing a D 2 desorption peak from B-D bonding known for its desorption temperature ~700 K. We introduce a separation procedure of observed D TPD signals, convoluted for corresponding D retention pathways, that was necessary for TPD analysis. This is the first report on the retention of D 2 neutral gas to B, and this observation was enabled by utilizing the B powder sample, which has a larger surface area than films commonly used in laboratory experiments. In conclusion, the upgraded SES system will enable us to investigate hydrogen isotope behaviors for powder/dust samples of various elemental compositions, including metals.

Plasma-facing component debris↗
DOE OSTI2024

Renewable low-Z wall for fusion reactors with built-in tritium recovery (Final Technical Report)

This project pursued development of a novel renewable plasma-facing wall technology for fusion reactors. The technology is based on a slurry which can be easily delivered by delivery tubes to the reactor wall. The slurry dries at the hot reactor wall into pebble rods which are extruded out into the hot plasma, where the pebbles break off and fall along the reactor wall and can be recovered by gravity and re-used. The falling pebbles carry away heat and tritium and also protect the wall against large scale erosion or redeposition of material. The research focused on carbon-based pebble rods and demonstrated that pebble rods could be produced from slurry with tolerable levels of outgassing on a reactor-relevant timescale (< 5 minutes). Steady-state handling of reactor relevant (up to 50 MW/m 2 ) normal-incidence heat loads was demonstrated. Pebble release velocities were found to be sufficiently small (< 1 m/s) to allow recovery below the vacuum chamber. Tunability of the pebble rod breaking rate was demonstrated by changing the fill fraction of the interpebble matrix which binds the pebbles together. This work could benefit the public by helping move forward the design of commercially viable fusion energy reactors. Designing a first wall for magnetic fusion reactors which can handle the huge heat loads present and also avoid buildup of tritium-containing deposits is extremely challenging and requires novel approaches like the one being investigated here.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Design-informed neutronics assessment of long-lived fission product transmutation in a tokamak fusion reactor blanket

This study presents a neutronics-based assessment of the feasibility and viability of transmuting six major long-lived fission products (LLFPs) from light-water reactors, namely 99 Tc, 129 I, 79 Se, 93 Zr, 126 Sn, and 135 Cs, within the blanket region of a tokamak fusion reactor, using the MIT ARC design as a concrete fusion configuration. Monte Carlo neutronics simulations were performed to evaluate LLFP transmutation and to compare the results with a reference boiling water reactor (BWR). The results indicate that transmutation of all six LLFPs is neutronics-feasible in fusion reactors, with transmutation half-lives significantly shorter than their natural decay half-lives. For elemental targets, transmutation of 135 Cs, 126 Sn, and 93 Zr was found potentially viable, as the net mass transmuted exceeded that achievable in the reference BWR under identical target volume and irradiation time. When isotopically separated targets were considered, transmutation of 126 Sn and 93 Zr appeared potentially viable. A parametric study demonstrated that plasma geometry modifications can enhance local neutron flux, increasing the transmuted 93 Zr mass by approximately 33% and reducing the transmutation half-life from approximately 240 years to 180 years. Repositioning the target and adjusting material layer thickness reduced the transmutation half-life of 93 Zr to 67 years and increased the net mass transmuted by a factor of 50. Furthermore, these results demonstrate that fusion reactors can enable LLFP transmutation beyond the practical limits of thermal fission reactors and highlight the critical role of reactor and blanket design optimization. Engineering and fuel-cycle considerations required for deployment are beyond the scope of this neutronics-focused study.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Compatibility of Type 304H Stainless Steel in Static Molten FLiBe for Inertial Confinement Fusion Reactors: Role of Impurities and Redox Control

Molten fluoride salts, such as FLiBe (LiF-BeF2), are promising candidates for tritium breeding and heat transfer in fusion reactors, but corrosion of structural materials remains a major challenge. This study investigates the corrosion behavior of austenitic stainless steel 304H in purified and NiF2-containing FLiBe at 500°C and 600°C, focusing on the effects of impurities and redox control. Exposure to purified FLiBe resulted in the concurrent depletion of Cr, Mn, and Fe, with corrosion at 500 °C dominated by the combined oxide formation and elemental dissolution, while at 600°C elemental depletion was predominant. The addition of a controlled NiF2 impurity significantly accelerated corrosion at both temperatures, demonstrating the sensitivity of 304H to the salt redox state. Beryllium additions were effective in mitigating corrosion for both baseline and NiF2-containing FLiBe; minimal depletion of Cr, Mn, and Fe occurred with Be additions as low as 2.5 mg (147 wppm), and no NiBe intermetallics formed at 5 mg (294 wppm), indicating that small Be inventories can provide substantial protection without deleterious phase formation. Thermodynamic equilibrium and coupled thermodynamic-kinetic analyses at the salt-alloy interface suggested low corrosion rates in systems with limited hydrogen fluoride (HF) generation, highlighting the importance of salt redox control. Estimates for a Be addition rate were calculated for the HYLIFE-II fusion reactor that can mitigate corrosion-induced degradation, assuming complete conversion of tritium to tritium fluoride (TF). Overall, 304H shows reasonable compatibility with FLiBe under optimized redox conditions. These results provide quantitative guidance for material selection and salt management in fusion blanket and heat exchanger systems and motivate validation under flowing, nonisothermal, and irradiated conditions.

Pillai, Rishi [ORNL] (ORCID:0000000243688197)↗
DOE OSTI2026

A Streamlined, Open Source Neutronics Toolkit for Fusion Reactor Design (Final Report)

Final report for the DOE Fusion Energy Sciences project titled "A Streamlined, Open Source Neutronics Toolkit for Fusion Reactor Design". This project developed unstructured mesh tracking capabilities in OpenMC as well as two shutdown dose rate methodologies, and performed extensive performance improvements and validation of the open source Monte Carlo code, OpenMC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Suppression of irradiation hardening in tungsten-coated ferritic steel for fusion reactor blanket applications

W-coated reduced activation ferritic steels have been developed for use as plasma facing components in fusion reactor blankets, offering excellent sputtering resistance and structural strength. Previous high-temperature coating methods, such as diffusion bonding and brazing, caused interfacial deterioration due to thermal stress from mismatched thermal expansion between W and reduced activation ferritic steel. To address this, underwater explosive welding was introduced as a high-velocity cold process that joins dissimilar materials while maintaining a strong, thin interface without the thermal issues associated with traditional methods. In this study, the effects of neutron irradiation on the hardness and microstructure in W-coated F82H reduced activation ferritic steel (W/F82H) joined by underwater explosive welding are investigated. Following neutron irradiation at 290 °C, irradiation hardening is suppressed in W, F82H, and their interface within the W/F82H material. Furthermore, microstructural observations indicate that the recovery of work hardening and relaxation of elastic strain introduced during coating significantly contribute to the suppression of irradiation hardening in W/F82H. In conclusion, W/F82H exhibits significantly suppressed irradiation hardening compared with those in stand-alone materials. This suppression is explained by residual stress from thermal expansion mismatch and the unique microstructure at the interface. These results provide valuable insights for the development of more durable materials in nuclear fusion applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Overview of the KSTAR experiments toward fusion reactor

The Korean Superconducting Tokamak Advanced Research has been focused on exploring the key physics and engineering issues for future fusion reactors by demonstrating the long pulse operation of high beta steady-state discharge. Advanced scenarios are being developed with the goal for steady-state operation, and significant progress has been made in high ℓ i , hybrid and high beta scenarios with β N of 3. In the new operation scenario called fast ion regulated enhanced (FIRE), fast ions play an essential role in confinement enhancement. GK simulations show a significant reduction of the thermal energy flux when the thermal ion fraction decreases and the main ion density gradient is reversed by the fast ions in FIRE mode. Optimization of 3D magnetic field techniques, including adaptive control and real-time machine learning control algorithm, enabled long-pulse operation and high-performance ELM-suppressed discharge. Symmetric multiple shattered pellet injections (SPIs) and real-time disruption event characterization and forecasting are being performed to mitigate and avoid the disruptions associated with high-performance, long-pulse ITER-like scenarios. Finally, the near-term research plan will be addressed with the actively cooled tungsten divertor, a major upgrade of the NBI and helicon current drive heating, and transition to a full metallic wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Thermal Gradient and Neutron Irradiation Experiment Design for Fusion Reactor Materials in the Advanced Test Reactor

This work outlines a hypothetical coupled thermal gradient and neutron irradiation experiment in the Advanced Test Reactor (ATR) at the Idaho National Laboratory. Although the ATR is a thermal spectrum test reactor and doesn’t inherently produce a flux spectrum dominated by the high-energy neutrons typical in a fusion reactor, it’s multitude of experiment positions and dynamic flux environment make it a suitable platform for investigating fusion related issues.

36 MATERIALS SCIENCE↗
DOE OSTI2025

FY25 Theory and Simulation Performance Target: Development of an integrated modeling framework for fusion reactor design and assessment (Final Report)

This report documents the FY25 Theory and Simulation Performance Target (TSPT) of developing an integrated modeling framework for fusion reactor design and assessment (FREDA). Over Q1-Q4, new capabilities were developed across both plasma and engineering domains and demonstrated on an example representation of a Compact Advanced Tokamak with a Dual Cooled Lead Lithium blanket. This represents a first-of-a-kind demonstration of coupled core-to-wall-to-engineering for a reactor. Self-consistent CESOL workflows were applied to provide core, pedestal, and SOL prediction; new modules were developed for energetic particle stability (FAR3D) and transport (TGLF-EP) analysis; and boundary plasma modeling (SOLPS-ITER, BOUT++/Hermes-3) was expanded to evaluate wall and divertor heat fluxes and interface with engineering thermal analysis. A parameterized CAD tool, TRACER, was expanded to generate medium-fidelity divertor, blanket, and coil geometries; OpenFOAM and Diablo workflows were applied for first-wall and divertor thermal analyses with helium cooling; and reduced-order models were created for high-mass-flux divertor cooling. Magnet multiphysics capabilities were verified between Elmer, Diablo, and a new MFEM-based solver, and workflows enable stress, thermal, and neutron-fluence analysis of TF coils with neutronics-driven heating. Nuclear and blanket analysis workflows were demonstrated, including tritium breeding, transport, and CFD-informed thermo-mechanical assessment. Preliminary multi-fidelity uncertainty quantification workflows were applied to boundary modeling codes and shown to achieve variance reductions with fewer high-fidelity boundary simulations. Key findings highlight the challenges of resolving the ITEP gap to find suitable balance between wall and divertor loads, neutron heating, and practical limits of PFC cooling. Next step priorities are to develop automated workflows to check boundary code convergence and detachment, implement tighter physics-engineering CAD provenance tracking, and inclusion of plasma-material interface models for SLAG and tungsten cracking behavior. Collectively, these developments establish sophisticated capabilities for predictive, multi-fidelity, whole-device modeling that integrates plasma physics, materials, magnets, and nuclear engineering to guide pathways to viable Fusion Pilot Plant design points.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Comprehensive new insights on the potential use of SiC as plasma-facing materials in future fusion reactors

Abstract The performance of silicon carbide as an alternative plasma facing material (PFM) was studied at various irradiation conditions relevant to ion energies and fluxes of a fusion reactor. This analysis involves detailed modeling of subsurface plasma/material interactions, sputtered particle transport above the surface and redeposition, and related changes in material composition and microstructure induced by steady-state and Edge Localized Mode ion fluxes. Transition of a crystalline SiC surface to semi-crystalline and amorphous phases was analyzed based on advanced modeling of DIII-D tokamak experiments where SiC was irradiated in single- and multiple- L-mode and H-mode discharges. This analysis shows that displacement damage, particle deposition/redeposition, and D accumulation on the SiC divertor surface can lead to significant microstructural changes that result in enhanced sputtering erosion in comparison with the original crystalline material. However, the resulting total net erosion rate for a full-coverage, advanced tokamak, SiC coated divertor may well be acceptably low. Moreover, the C sputtering yield from the evolved SiC surface can be seven times lower than from a pure graphite surface; this would imply significantly reduced tritium co-deposition rates in a D-T tokamak reactor, compared with a pure carbon surface. It was also determined that chemical sputtering of both C and Si should not result in any noticeable effect on the net erosion, for attached plasma regimes. Our results thus show encouraging results overall for use of SiC as a PFM in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Efficient ECCD non-inductive plasma current start-up, ramp-up, and sustainment for an ST fusion reactor

The elimination of the need for an Ohmic heating solenoid may be the most impactful design driver for the realization of economical compact fusion tokamak reactor systems. However, this would require fully non-inductive start-up and current ramp-up from zero plasma current and low electron temperature of sub-keV to the full plasma current of ~10–15 MA at 20–30 keV electron temperature. To address this challenge, an efficient solenoid-free start-up and ramp-up scenario utilizing a low-field-side-launched extraordinary mode at the fundamental electron cyclotron harmonic frequency (X–I) is proposed, which has more than two orders of magnitude higher electron cyclotron current drive (ECCD) efficiency than the conventional ECCD for the sub-keV start-up regime. A time dependent model was developed to simulate the start-up scenarios. For the Spherical Tokamak Advanced Reactor (STAR) (Menard et al 2023 Next-Step Low-Aspect-Ratio Tokamak Design Studies (IAEA)), it was found that to fully non-inductively ramp-up to 15 MA, it would take about 25 MW of EC power at 170 GHz. Because of the relatively large plasma volume of STAR, radiation losses must be considered. It is important to make sure that high Z impurities are kept sufficiently low during the early current start-up phase where the temperature is sub-keV range. Since the initial current ramp up takes place at a factor of ten lower density compared to the sustained regimes, it is important to transition into a higher bootstrap fraction discharge at lower density to minimize the ECCD power requirement during the densification. For the sustainment phase an array of eight gyrotron launchers with a total of about 60 MW of fundamental O-mode was found to be sufficient to provide the required axis-peaked external current drive. High efficiencies between 19–57 kA MW –1 were found with optimal aiming, and these were resilient to small changes in aiming angles and density and temperature profiles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗