Search NASA⌕ Search

SEARCH · Search NASA

Results for “GAS CYLINDERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Heavy Duty Natural Gas Single Cylinder Research Engine Installation, Commissioning, and Baseline Testing

Natural Gas (NG) Internal Combustion Engines (ICE) are a promising alternative to diesel engines for on-road heavy-duty applications to reduce greenhouse gas and harmful pollutant emissions. NG engines have not been widely adopted due to the lower thermal efficiency compared with diesel engine counterparts. To develop the base knowledge required to reach the desired efficiency, a Single Cylinder Engine (SCE) is the most effective platform to acquire reliable and repeatable data. A SCE test cell was developed using a Cummins 15-liter six-cylinder heavy-duty engine block modified to fire one cylinder (2.5-liter displacement). A Woodward Large Engine Control Module (LECM) is integrated to permit implementation of real-time advanced combustion control. Intake and exhaust characteristics, fuel composition, and exhaust gas recirculated substitution rate (EGR) are fully adjustable. A high-speed data acquisition system acquires in-cylinder, intake, and exhaust pressure for combustion analysis. The baseline testing shows reliable and consistent results for engine thermal efficiency, indicated mean effective pressure (IMEP), and coefficient of variance of the IMEP over a wide range of operating conditions while achieving effective control of all engine control and operation variables. This test cell will be used to conduct a research program to develop new and innovative control algorithms and CFD optimized combustion chamber designs, allowing ultra-high efficiency and low emissions for NG ICE heavy-duty on-road applications.

03 NATURAL GAS↗
DOE OSTI2024

Excerpt from Oxygen Monitor Clean Testing Report Performed in 2010

The Rosemount X-STREAM Series X2GP is a paramagnetic oxygen analyzer with a 0-25% oxygen measurement range. It claims a drift less than 2% of span (0.10% volume oxygen) per week, and a response time of less than 5 seconds (for the analyzer to report 90% of a step change). Our test equipment was set-up such that the same gas was running through each oxygen analyzer at the same time. This allowed Calibration Error, Calibration Drift, and Loss of Power Testing to be run on all monitors at the same time, eliminating any variability between the analyzers from tolerances in the gas cylinder, ambient temperature, ambient pressure, test duration, etc. An APTech pressure regulator was placed on the gas cylinder manifold and a 23 psia Paroscientific pressure transducer measured the regulator’s outlet pressure. This did not give the inlet pressure on any one analyzer but outlet pressure from the manifold before the stream was split. The APTech pressure regulator was used to keep operating conditions consistent. A DWYER rotameter was installed on each oxygen monitor’s outlet piping. With the exception of Variation of Flow Rate Testing, the rotameter was left fully open for all testing. The flow rate through each oxygen monitor was controlled by a Swagelok needle valve that was installed on each analyzer’s inlet piping. Additionally, a filter was installed in the each monitor’s inlet piping to keep particles from the measurement cells and a Swagelok ball valve was installed on each monitor’s outlet piping to isolate each monitor between tests. No pumps were installed. Each of the cylinders used was at a pressure greater than ambient room barometric pressure. This pressure differential was used to move gas through the testing equipment. The flow rate through each analyzer was controlled by the Swagelok needle valve installed on each analyzer’s inlet piping. Finally, for all tests, a Paroscientific Digiquartz Barometer was used to measure ambient room barometric pressure and a Fluke Thermo-hygrometer was used to measure ambient room temperature.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Next-Cycle Optimal Fuel Control for Cycle-to-Cycle Variability Reduction in EGR-Diluted Combustion

In this simulation study, cycle-to-cycle fuel control was used to reduce CCV by injecting additional fuel in operating conditions with sporadic misfires and partial burns. An optimal control policy was proposed that utilizes 1) a physics-based model that tracks in-cylinder gas composition and 2) a one-step-ahead prediction of the combustion efficiency based on a kernel density estimator. The optimal solution, however, presents a tradeoff between the reduction in combustion CCV and the increase in fuel injection quantity required to stabilize the charge. Such a tradeoff can be ad- just by a single parameter embedded in the cost function.

Maldonado, BryanP. [Oak Ridge National Lab. (ORNL)↗
DOE OSTI2021

Effect of slip on vortex shedding from a circular cylinder in a gas flow

Most studies of vortex shedding from a circular cylinder in a gas flow have explicitly or implicitly assumed that the no-slip condition applies on the cylinder surface. To investigate the effect of slip, vortex shedding is simulated using molecular gas dynamics (the direct simulation Monte Carlo method) and computational fluid dynamics (the incompressible Navier-Stokes equations with a slip boundary condition). A Reynolds number of 100, a Mach number of 0.3, and a corresponding Knudsen number of 0.0048 are examined. For these conditions, compressibility effects are small, and periodic laminar vortex shedding is obtained. Slip on the cylinder is varied using combinations of diffuse and specular molecular reflections with accommodation coefficients from zero (maximum slip) to unity (minimum slip). Although unrealistic, bounce-back molecular reflections are also examined because they approximate the no-slip boundary condition (zero slip). The results from both methods are in reasonable agreement. The shedding frequency increases slightly as the accommodation coefficient is decreased, and shedding ceases at low accommodation coefficients (large slip). The streamwise and transverse forces decrease as the accommodation coefficient is decreased. Based on the good agreement between the two methods, computational fluid dynamics is used to determine the critical accommodation coefficient below which vortex shedding ceases for Reynolds numbers of 60–100 at a Mach number of 0.3. Finally, conditions to observe the effect of slip on vortex shedding appear to be experimentally realizable, although challenging.

42 ENGINEERING↗
DOE OSTI2025

Integration of CO 2 capture and microalgae cultivation: demonstration assessment of outdoor Scenedesmus acutus cultivation using gaseous ammonia as a nitrogen source

Towards the goal of integrating CO 2 capture using aqueous ammonia with its utilization for algae cultivation, Scenedesmus acutus (UTEX B72) was grown in 1100 L open raceway ponds using CO 2 and NH 3 supplied from gas cylinders. CO 2 /NH 3 mole ratios of 7 and 10 were employed, the gas mixture acting as a surrogate for the output from a CO 2 scrubbing system using aqueous ammonia. Compared to Scenedesmus acutus grown in open ponds using gaseous CO 2 and NaNO 3 as the N-source, the ponds supplied with gaseous CO 2 and NH 3 displayed higher productivity at both CO 2 /NH 3 ratios, with the higher ratio providing the best growth. Depending on the culturing conditions and CO 2 /NH 3 ratio, CO 2 utilization ranged up to 15.8% and NH 3 utilization to 23.0%. These rather low values reflect the fact the high CO 2 /NH 3 feed rate used, resulting in a substantial release of NH 3 from the ORPs (~45%). Finally, these findings demonstrate the suitability of gaseous NH 3 as a N-source for microalgae cultivation, while highlighting the need for a control strategy that closely balances the CO 2 /NH 3 supply with the algae growth rate. The produced algae biomass possessed a high protein and low ash content, rendering it particularly suitable for use as a bioplastic feedstock.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Mixed gases in compressed cylinders: some popular misconceptions and explanations

Many industrial applications and scientific investigations require gaseous premixes. These are generally available in compressed gas cylinders from commercial vendors. Despite many decades of working knowledge with compressed premixed gases, various individuals from the production plants have expressed concerns regarding the ability of the gases to remain mixed in storage and delivery. In this brief tutorial, we show the mathematics and physics that underwrite our confidence in the use of premixed gases as we explain the following: The conditions in which separation of gases due to gravity is of practical concern; The conditions for preferential extraction of lighter gases from premixed gas tank; The time length necessary for homogeneous mixing of gases by molecular kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Observation and Characterization of Vibrationally Active Surface Species Accessed with Nonthermal Nitrogen Plasmas

Polycrystalline Ni, Pd, Cu, Ag, and Au foils exposed to nonthermal plasma (NTP)-activated N 2 are found to exhibit a vibrational feature near 2200 cm –1 in polarization-modulation infrared reflection-absorption spectroscopy (PM-IRAS) observations that are not present in the same materials exposed to N 2 under nonplasma conditions. The feature is similar to that reported elsewhere and is typically assigned to chemisorbed N 2 . We employ a combination of temperature-dependent experiments, sequential dosing, X-ray photoelectron spectroscopy, isotopic labeling, and density functional theory calculations to characterize the feature. Results are most consistent with a triatomic species, likely NCO, with the C and O likely originating from ppm-level impurities in the ultrahigh-purity (UHP) Ar and/or N 2 gas cylinders. Here, this work highlights the potential for nonthermal plasmas to access adsorbates inaccessible thermally as well as the potential contributions of ppm-level impurities to corrupt the interpretation of plasma catalytic chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

ECAR-1943 AGC-1 INDIVIDUAL SPECIMEN FLUENCE, TEMPERATURE, AND LOAD CALCULATION AND TABULATION

This ECAR calculates the fluence and temperature of the AGC-1 specimens as they change elevation through the course of the experiment. The specimen elevation varies as the specimen stack shrinks due to irradiation and load induced creep. The compressed specimen stacks (S-1 thru S-6) have a graphite pushrod that applies a gas cylinder load. The top of the pushrod position is measured and recorded in the NGNP Data Management and Analysis System (NDMAS). The bottom of each of these compressed stacks is supported by the lower specimen holder which also shrinks as a result of irradiation and load. The specimen holder post-irradiation length was recorded during post-irradiation examination (PIE). Assuming the specimen holder shrinkage is linear with respect to the fluence received, the position of the top of the specimen holder can be calculated with respect to reactor integrated power. Assuming that individual specimen shrinkage is proportional to the fluence received, and that the shrinkage behavior is similar in all the specimens, the individual specimen position can be calculated.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Design and Development of a High-Efficiency Single Cylinder Natural Gas-Fueled Jet Ignition Engine

The current energy climate has created a push toward reducing consumption of fossil fuels and lowering emissions output in power generation applications. Combined with the desire for a more distributed energy grid, there is currently a need for small displacement, high efficiency engines for use in stationary power generation. An enabling technology for achieving high efficiencies with spark ignited engines for such applications is the use of jet ignition which enables ultra-lean (λ > ~1.6) combustion via air dilution.This paper provides a comprehensive review of the development of a 390cc, high efficiency single cylinder natural gas-fueled jet ignition engine operating ultra-lean. The engine was developed as part of the Department of Energy’s Advanced Research Projects Agency–Energy (DOE ARPA-E) GENSETS program. Design choices for minimizing friction are highlighted as well as test results showing further friction reduction through downspeeding. Extensive hardware optimization of the combustion system has been performed and results are presented for air-flow path optimization and the jet igniter. The efficiency benefits related to enleanment and downspeeding are analyzed using an efficiency loss breakdown based on the First Law of Thermodynamics. Through optimization efforts a peak brake thermal efficiency in excess of 34% was achieved, representing an increase of greater than 20% over the current state-of-the-industry for comparably sized CNG engines.

Peters, Nathan↗
DOE OSTI2021

Crankcase ventilation systems

An internal combustion engine may be used to compress natural gas for vehicle fuel. The engine may contain a plurality of gas compression cylinders, at least one standard combustion cylinder to drive the compression cylinders, and a common crankshaft in a crankcase coupling the compression cylinders and the at least one standard combustion cylinder. Some combustible gas being compressed may leak past the piston rings of the compression cylinders into the engine crankcase posing a safety concern. This invention eliminates this concern by actively flushing the crankcase at a higher rate than normal.

Babbitt, Guy Robert↗
DOE OSTI2025

Summary of UMI Chemical Work

Our initial work for the Urban Modeling Integration (UMI) project was to validate the QUIC model dense gas dispersion of chlorine advection up a ramp. The validation task was to use QUIC to model an experiment done in a wind tunnel. Naturally the QUIC model uses a slumping cylindrical model where inside the cylinder the gas is treated as dense but outside ideal. In trying to validate using the wind tunnel experiment, due to the scale of the wind tunnel experiment and ramp, The model formed a very clear, discrete, concentration barrier at the edge of the cylinder that likely doesn’t line up well with the real dense gas advection/diffusion. This effect is much less noticeable at a larger scale such as an instantaneous release of a 25 ton tank.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI1991

Pressure Safety Training (Rev. 8)

This is the workbook for the Pressure Safety Training Course. It is intended as a reference manual and guide for all work with pressurized liquids or gases. This workbook contains basic references to make work with pressure safer. It is intended to supplement classroom instruction, rather than serve as a definitive text on pressure. Earlier versions of the manual were intended specifically for training at Lawrence Livermore National Laboratory. This revision is a generic version intended for training at all DOE facilities. The information in the Standards chapter is from the LLNL Health and Safety Manual. It is included here as a convenient reference and guide for developing similar standards at your own facility.

42 ENGINEERING↗
DOE OSTI2025

New helium recapture and reliquefier system for Dynamic Nuclear Polarization at UNH.

A new helium recapture and reliquefaction system, consisting of a gas bag, recapture manifold, cooling chiller, cryogenic purifier and, a gas storage cylinder banks, has been installed in the dynamic nuclear polarized target lab at the University of New Hampshire. This new system has the capability to improve the efficiency of our capacity to do target polarization runs by recycling our cryogenic helium which would otherwise be lost during polarization operations. Our helium liquefier is rated upto 40 L/Day under normal full-capacity operations, and is rated for a capacity of 500 liquid liters of helium. I explain the initial installation process followed by a discussion of the challenges with installation, including issues of impurities which appeared during the initial operation of the system. Then I discuss how we overcame these difficulties. Finally, I discuss the function of the system during normal operation and the present situation of the helium recapture and reliquefaction processing in the UNH Lab.

Lama, Chhetra [Univ. of New Hampshire, Durham, NH ↗
DOE OSTI2023

Physically-based control-oriented modeling for turbocharged stoichiometric spark-ignited engine with cooled EGR and flexible VVT systems

Accurate estimation and prediction of engine gas exchange system and in-cylinder conditions are critical for spark-ignited engine control and diagnostic algorithm development. In this paper, a physically-based, control-oriented model for a 2.8 l turbocharged, variable valve timing (VVT) and low pressure (LP) exhaust gas recirculation (EGR)-utilizing SI engine was developed. The model includes the impact of modulation to any combination of 10 actuators, including the throttle valve, compressor bypass valve, fueling rate, waste-gate, LP EGR valve, number of deactivated cylinders, intake valve open (IVO) timing, intake valve close (IVC) timing, exhaust valve open (EVO) timing and exhaust valve close (EVC) timing. The accuracy of the model in capturing engine dynamics was demonstrated by validating it against high-fidelity engine GT-Power simulation results for various drive cycles, particularly emphasizing elevated loads. In comparison to the open literature, novel contributions of the effort described in this paper includes in-cylinder gas composition modeling and turbine-out pressure estimation.

Zhang, Xu↗
DOE OSTI2020

A Conceptual Design for a Mobile Application to Support Infield Inventory Activities

This paper introduces an inventory assistant being developed at Oak Ridge National Laboratory (ORNL) that we believe will empower users to perform inventory activities at nuclear facilities more accurately, reliably, and quickly. Inventory activities at nuclear facilities are often conducted using pen and paper, which can be time-consuming, tedious, and susceptible to reading or transcription errors. The proposed inventory assistant would replace the paper-based process used by International Atomic Energy Agency (IAEA) inspectors, nuclear facility operators, or verification monitors to complete an inventory of nuclear and non-nuclear items. In general, the inventory assistant would ingest an inventory list, distribute assigned items from the inventory list to one or more mobile devices, enable inventory teams to record their observations in the field, and then enable an inventory lead to integrate and reconcile the observations to produce a final report. The assistant consists of two software components—one for the inventory teams to record observations in the field (In-Field Observations App [IFOA]) and one for the inventory lead to reconcile the inventory list with observations (Distribution, Integration, and Reconciliation Application [DIRA]). This paper introduces the overall workflow of the inventory assistant and describes the IFOA user experience in more detail. To demonstrate the concept, the authors present a use case of IAEA inspectors conducting item counting and tag checking activities of UF6 cylinders at a gas centrifuge enrichment plant with a large number of UF6 cylinders (e.g., thousands). These activities can currently require 30–40 person-days of inspection to complete. Based on experiences during an exercised performed at the IAEA by the ORNL team in 2016, we believe an inventory assistant could allow the IAEA to complete item counting and tag checking using the global identifier or the operator’s barcode in 8–10 person-days of inspection. We would expect other users (e.g., facility operators or verification monitors) to also benefit from significant time savings.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗