Search NASA⌕ Search

SEARCH · Search NASA

Results for “GRAIN REFINEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone

The microstructure of acicular ferrite and its formation for the grain refinement of coarse-grained region of heat-affected zone of high strength low-alloy bainite steels were studied using three-dimensional reconstruction technique. Crystallographic grain size was analyzed by means of electron backscatter diffraction. It was revealed that the microstructure in the coarse-grained region of the heat-affected zone consisted of predominantly bainite packets and a small proportion of acicular ferrite. Acicular ferrite was of lath or plate-like rather than needle or rod-like morphology. Tempering of the coarse-grained region of heat-affected zone showed that the acicular ferrite was more stable than the bainite, indicating that the acicular ferrite was formed prior to bainite. The acicular ferrite laths or plates divided the prior austenite grains into smaller and separate regions, and confining the bainite transformed at lower temperatures in the smaller regions and hence leading to the grain refinement in the coarse-grained region of the heat-affected zone.

36 MATERIALS SCIENCE↗

The grain refinement mechanisms of various phases in shot-peened Nickel-Aluminum bronze (NAB) alloy

Highlights: • There exist two grain refinement mechanisms at the same time in the α phase. • The refinement of β' phase is attributed to the formation of dense and ordered nano twins. • The brittle strip-shape κ{sub iii} phases are fragmented after large deformation. • The κ{sub iv} and κ{sub ii} phases exhibit the twinning and dislocation deformation modes, separately. • The microhardness increases significantly owing to work hardening effect and grain refinement. - Abstract: In this study, coarse-grained Nickel-Aluminum bronze (NAB) alloy is subjected to shot-peening (SP) treatment, and the grain refinement mechanisms of various phases in shot-peened NAB alloy are investigated separately. The results show that severe deformation layers are produced on the surface. Meanwhile, refined grains with the average size below 100 nm are induced through SP treatment indicated by the results of X-ray diffraction (XRD) patterns. Various phases in NAB alloy including α, β' and three intermetallic phases (κ{sub ii}, κ{sub iii} and κ{sub iv}) display different grain refinement mechanisms. The grain refinement in the α phase involves dislocation segmentation in the precipitation-free zone and the twinning intersection in the precipitation zone. The formation of nanotwins by emitting partial dislocations at the grain boundary is found to be responsible for the grain refinement in the β' phase. As for the κ phases, the strip-shaped κ{sub iii} phases are fragmented after severe deformation, and the κ{sub iv} and κ{sub ii} phases exhibit the twinning and dislocation deformation modes, respectively. Also, the microhardness is significantly enhanced after SP treatment, which is mainly attributed to the work hardening effect and grain refinement.

36 MATERIALS SCIENCE↗

A New Grain Refiner for Ferritic Steels

A new grain refiner, LaB{sub 6}, was identified for ferritic steels based on the crystallographic calculation using the edge-to-edge matching model. Addition of 0.5 wt pct LaB{sub 6} led to a reduction of the average grain size from 765 to 92 μm and the proportion of the columnar structure from 35 to 8 pct in an as-cast Fe-4Si ferritic alloy. Although LaB{sub 6} was supposed to act as an active inoculant for δ-ferrite, thermodynamic calculation indicated that LaB{sub 6} is not thermodynamically stable in the melt of the Fe-4Si alloy. It was subject to decompose into La and B solutes. Consequently, both La and B reacted with Fe, O and S, forming different compounds. Microstructural examination at room temperature observed La{sub 2}SO{sub 2} and La{sub 2}O{sub 3} particles within the ferrite grains and Fe{sub 2}B along the grain boundaries in the samples. Through EBSD analysis, a reproducible orientation relationship between ferrite and La{sub 2}SO{sub 2} was identified. In addition, the edge-to-edge matching calculation also predicted the high potency for La{sub 2}SO{sub 2} to be an effective nucleant for δ-ferrite. It was considered that the grain refinement of LaB{sub 6} was attributed to the enhanced heterogeneous nucleation of δ-ferrite by La{sub 2}SO{sub 2}, and the solute effect of B due to the high Q-value in ferrite.

36 MATERIALS SCIENCE↗

Influence of Alloy and Solidification Parameters on Grain Refinement in Aluminum Weld Metal due to Inoculation

The goals are: (1) Establish how much Ti/B grain refiner is need to completely refine aluminum weld metal for different alloys and different welding conditions; (2) Characterize how alloy composition and solidification parameters affect weld metal grain refinement; and (3) Apply relevant theory to understand observed behavior. Conclusions are: (1) additions of Ti/B grain refiner to weld metal in Alloys 1050, 5083, and 6082 resulted in significant grain refinement; (2) grain refinement was more effective in GTAW than LBW, resulting in finer grains at lower Ti content - reason is limited time available for equiaxed grain growth in LBW (inability to occlude columnar grain growth); (3) welding travel speed did not markedly affect grain size within GTAW and LBW clusters; and (4) application of Hunt CET analysis showed experimental G to be on the order of the critical G{sub CET}; G{sub CET} was consistently higher for GTAW than for LBW.

36 MATERIALS SCIENCE↗

Novel Fabrication of a TiB{sub 2} Grain Refiner and its Effect on Reducing Hot Tearing in AZ91D Magnesium Alloy

Despite the increased use of magnesium (Mg) alloys in diverse engineering applications in recent years, further incorporation of complex Mg alloy castings remains challenging due to the alloy’s relatively high susceptibility to hot tearing. A significant reduction in hot tearing via grain refinement was achieved in aluminum and ferrous alloys; however, an effective, long-lasting and inexpensive grain refiner for aluminum-containing Mg alloys remains elusive. In this work, a TiB{sub 2} grain refiner was fabricated via a novel spark plasma sintering (SPS) powder metallurgy process. Then, its effectiveness in grain refining an AZ91D magnesium alloy was compared to that of a commercially available TiB{sub 2} grain refiner produced by hot extrusion. Due to the homogeneous distribution of the TiAl{sub 3} and TiB{sub 2} particles in the grain refiner, as well as their effect on the alloy’s microstructure evolution and solidification behavior, the SPS-TiB{sub 2} grain refiner was observed to achieve a significant reduction in the grain size and hot tearing of the Al-containing AZ91D magnesium alloy.

36 MATERIALS SCIENCE↗

Grain refinement of a nickel and manganese free austenitic stainless steel produced by pressurized solution nitriding

Prolonged exposure at high temperatures during solution nitriding induces grain coarsening which deteriorates the mechanical properties of high nitrogen austenitic stainless steels. In this study, grain refinement of nickel and manganese free Fe–22.75Cr–2.42Mo–1.17N high nitrogen austenitic stainless steel plates was investigated via a two-stage heat treatment procedure. Initially, the coarse-grained austenitic stainless steel samples were subjected to an isothermal heating at 700 °C to be decomposed into the ferrite + Cr{sub 2}N eutectoid structure and then re-austenitized at 1200 °C followed by water quenching. Microstructure and hardness of samples were characterized using X-ray diffraction, optical and scanning electron microscopy, and micro-hardness testing. The results showed that the as-solution-nitrided steel decomposes non-uniformly to the colonies of ferrite and Cr{sub 2}N nitrides with strip like morphology after isothermal heat treatment at 700 °C. Additionally, the complete dissolution of the Cr{sub 2}N precipitates located in the sample edges during re-austenitizing requires longer times than 1 h. In order to avoid this problem an intermediate nitrogen homogenizing heat treatment cycle at 1200 °C for 10 h was applied before grain refinement process. As a result, the initial austenite was uniformly decomposed during the first stage, and a fine grained austenitic structure with average grain size of about 20 μm was successfully obtained by re-austenitizing for 10 min. - Highlights: • Successful grain refinement of Fe–22.75Cr–2.42Mo–1.17N steel by heat treatment • Using the γ → α + Cr{sub 2}N reaction for grain refinement of a Ni and Mn free HNASS • Obtaining a single phase austenitic structure with average grain size of ∼ 20 μm • Incomplete dissolution of Cr{sub 2}N during re-austenitizing at 1200 °C for long times • Reducing re-austenitizing time by homogenizing treatment before grain refinement.

36 MATERIALS SCIENCE↗

Precipitation process in a Mg–Gd–Y alloy grain-refined by Al addition

The precipitation process in Mg–10Gd–3Y (wt.%) alloy grain-refined by 0.8 wt.% Al addition has been investigated by transmission electron microscopy. The alloy was given a solution treatment at 520 °C for 6 h plus 550 °C for 7 h before ageing at 250 °C. Plate-shaped intermetallic particles with the 18R-type long-period stacking ordered structure were observed in the solution-treated state. Upon isothermal ageing at 250 °C, the following precipitation sequence was identified for the α-Mg supersaturated solution: β″ (D0{sub 19}) → β′ (bco) → β{sub 1} (fcc) → β (fcc). The observed precipitation process and age hardening response in the Al grain-refined Mg–10Gd–3Y alloy are compared with those reported in the Zr grain-refined counterpart. - Highlights: • The precipitation process in Mg–10Gd–3Y–0.8Al (wt.%) alloy has been investigated. • Particles with the 18R-type LPSO structure were observed in the solution state. • Upon ageing at 250 °C, the precipitation sequence is: β″ → β′ → β1 (fcc) → β. • The Al grain-refined alloy has a lower hardness than the Zr refined counterpart.

36 MATERIALS SCIENCE↗

Grain refinement of cast zinc through magnesium inoculation: Characterisation and mechanism

It was previously found that peritectic-forming solutes are more favourable for the grain refinement of cast Al alloys than eutectic-forming solutes. In this work, we report that the eutectic-forming solute, Mg, can also significantly grain refine cast Zn. Differential thermal analysis (DTA) of a Zn–Mg alloy, in which efficient grain refinement occurred, evidenced an unexpected peak that appeared before the nucleation of η-Zn grains on the DTA spectrum. Based on extensive examination using X-ray diffraction, high resolution SEM and EDS, it was found that: (a) some faceted Zn–Mg intermetallic particles were reproducibly observed; (b) the particles were located at or near grain centres; (c) the atomic ratio of Mg to Zn in the intermetallic compound was determined to be around 1/2. Using tilting selected area diffraction (SAD) and convergent beam Kikuchi line diffraction pattern (CBKLDP) techniques, these faceted particles were identified as MgZn{sub 2} and an orientation relationship between such grain-centred MgZn{sub 2} particles and the η-Zn matrix was determined. Hence, the unexpected peak on the DTA spectrum is believed to correspond to the formation of MgZn{sub 2} particles, which act as effective heterogeneous nucleation sites in the alloy. Together with the effect of Mg solute on restricting grain growth, such heterogeneous nucleation is cooperatively responsible for the grain size reduction in Zn–Mg alloys. - Highlights: • A new eutectic-based grain refiner for the cast Zn was found. • The formation process of an intermetallic compound (MgZn{sub 2}) was characterised. • MgZn{sub 2} can act as potent heterogeneous nucleation sites above the liquidus. • A new OR between MgZn{sub 2} and η-Zn was determined using the CBKLDP technique.

36 MATERIALS SCIENCE↗

Dynamic Recrystallization and Grain Refinement of Fe-P-C-Si and Fe-P-C-Si-N Steels

Grain refinement is an effective technique to improve the mechanical properties of steels. In the present work, single-pass hot compression experiments have been conducted on two different compositions of high phosphorous steels to study the microstructural evolution and ferrite grain refinement at various strain rates and deformation temperatures, i.e., 0.01-10 s{sup −1} and 750-1050 °C, respectively. Optical metallography has been employed to understand the physical processes that take place during hot deformation process. The results indicate that when these compositions of high phosphorous steels are worked at relatively low temperatures in the intercritical regions, a ferrite grain size of 5-7 µm is obtained. It is observed that the grain size decreases with an increase in strain rate and with the decrease in deformation temperature. Based on the values of stress exponent (n) obtained in the present work, dislocation creep is identified as the deformation mechanism. The activation energies for deformation of these two types of high phosphorous steels have been calculated. The effect of the alloying elements on the stress–strain curve, microstructure, and grain refinement has been discussed.

36 MATERIALS SCIENCE↗

Influence of Aluminum Content on Grain Refinement and Strength of AZ31 Magnesium GTA Weld Metal

The goal is to characterize the effect of Al content on AZ31 weld metal, the grain size and strength, and examine role of Al on grain refinement. The approach is to systematically vary the aluminum content of AZ31 weld metal, Measure average grain size in weld metal, and Measure cross-weld tensile properties and hardness. Conclusions are that: (1) increased Al content in AZ31 weld metal results in grain refinement Reason: higher undercooling during solidification; (2) weld metal grain refinement resulted in increased strength & hardness Reason: grain boundary strengthening; and (3) weld metal strength can be raised to wrought base metal levels.

36 MATERIALS SCIENCE↗

Application of Al-2La-1B Grain Refiner to Al-10Si-0.3Mg Casting Alloy

This paper reports the application and microstructure refining effect of an Al-2La-1B grain refiner in Al-10Si-0.3Mg casting alloy. Compared with the traditional Al-5Ti-1B refiner, Al-2La-1B refiner shows better performances on the grain refinement of Al-10Si-0.3Mg alloy. Transmission electron microscopy analysis suggests that the crystallite structure features of LaB6 are beneficial to the heterogeneous nucleation of α-Al grains. Regarding the mechanical performances, tensile properties of Al-10Si-0.3Mg casting alloy are prominently improved, due to the refined microstructures.

36 MATERIALS SCIENCE↗

Grain Refinement Effect on the Hot-Tearing Resistance of Higher-Temperature Al–Cu–Mn–Zr Alloys

The hot-tearing resistance of Al-Cu-Mn-Zr (ACMZ) alloys was investigated as a step toward introducing these new cast alloys for severe duty, higher-temperature applications, such as cylinder heads for down-sized, turbocharged automotive engines. Alloy Cu compositions were varied from 5 to 8 wt.%. Targeted Ti levels were 0.02, 0.1, and 0.2 wt.% via additions of the Al–5Ti–1B master alloy. Hot-tearing resistance was assessed by visual examination and ranking of the cracking severity in a multi-arm permanent mold casting. It was found that at high impurity contents (Fe and Si of 0.2 wt.% each), the Al–Cu–Mn–Zr alloy with 4.95 wt.% Cu exhibited the poorest hot-tearing resistance, irrespective of the grain refining amount. Microstructural analysis indicated an effective reduction in the grain size, as the Ti additions were increased to 0.02 and 0.1 wt.% Ti via the Al–Ti–B grain refiner. The finest grain size was attained with a 0.1 wt.% Ti. Based on the hot-tearing evaluation, it was found that the additional grain refining via the Al–5Ti–1B master alloy at 0.1 wt.% Ti significantly reduces the hot-tearing susceptibility at Cu contents greater than 7.3 wt.% for ACMZ alloys with low Fe and Si. These findings indicate that the best hot-tearing resistance was observed at a grain refiner level of 0.1 wt.% Ti and high Cu content (greater than 7.3 wt.%). This study to indicates that these Al–Cu–Mn–Zr alloys, which possess excellent microstructural stability and mechanical properties at elevated temperatures, can also possess excellent hot-tearing resistance.

36 MATERIALS SCIENCE↗

Micromechanisms of grain refinement during extrusion of Mg–0.3 at.% Al at low homologous temperature

Coarse grained Mg–0.3 at.% Al (0.33 in wt.%) alloy was processed by direct extrusion with a reduction ratio of 25:1 at a temperature of ∼ 433 K. The extrusion remainder was removed from the die and analysed in three distinct zones: the cast billet, the conical zone of extrusion die, and the as-extruded rod. The zones were characterized by electron backscatter diffraction (EBSD) and light microscopy techniques to identify the processes responsible for grain refinement. Complex networks of (10–12) twins in practically all grains produced a noticeable microstructural fragmentation even before the material reached the conical zone of the die. Deformation twinning extended up to the entrance zone of the conical die where it was followed by a continuous dynamic recrystallization (CDRX) that gradually changed low angle boundaries to high angle boundaries. It is apparent that geometrically necessary dislocations play a crucial role in the formation of new grain boundaries. CDRX results in a bimodal structure with grain diameters ∼ 3 and ∼ 30 μm. As a material flows through the conical zone, the ratio of large to small grains is progressively decreased by CDRX in favour of fine grains. The as-extruded microstructure (a rod 8 mm in diameter), with an average grain diameter of ∼ 2.1 μm, shows a strong texture where the vast majority of grains (99.99%) have the c-axis oriented at least 30° from the extrusion direction. - Highlights: • Coarse grained Mg–0.3 at.% Al alloy was extruded at temperature of ∼ 433 K. • Processes responsible for grain refinement were analysed in extrusion remainder. • In the first stage, complex (10–12) twinning produced a noticeable fragmentation. • Deformation twinning was followed by continuous dynamic recrystallization. • 99.99% of grains in extruded rod have c-axis oriented > 30° from extrusion direction.

36 MATERIALS SCIENCE↗

Effect of Grain Refining on Properties of a Cast Superaustenitic Stainless Steel

The goal of this study was to evaluate the industrial performance of cast high-alloy superaustenitic 19Cr-17Ni-6Mo stainless steel by refining the as-cast structure. A grain-refined, as-cast structure was achieved by the in situ inoculation with titanium nitrides (TiN) co-precipitated on previously formed spinel (MgAl{sub 2}O{sub 4}) inclusions, thus promoting heterogeneous nucleation of austenite during solidification. A homogenization heat treatment of the casting did not provide significant changes of the as-cast grain macrostructure in either the base or grain-refined steels. However, it was found that a combination of inoculation with heat treatment is an effective way of reducing interdendritic segregation. The industrial performance which includes the mechanical properties, corrosion resistance, and machinability was evaluated in the heat-treated condition for both base and inoculated steels. Tensile testing revealed improvements in ultimate tensile strength, ductility, and yield strength of the inoculated steel. The room-temperature impact properties exhibited a slight decrease in average impact energy but showed reduced variability in the inoculated steel compared to the base steel. The machining results showed that the inoculated steel had a slight improvement in machinability. The inoculated steel exhibited a lower corrosion rate but showed an increase in mass loss due to pitting. The changes in steel performance were linked to microstructure and nonmetallic inclusion families obtained by automated ASPEX SEM/EDX analysis.

36 MATERIALS SCIENCE↗

Corrosion Behavior of B and Ti Grain-Refined Sr-Modified A356

Corrosion behavior of A356 aluminum alloy with different grain refiners was evaluated. For this purpose, the Sr-modified A356 alloy was grain refined with Al5Ti1B and Al3B, and then, the corrosion characteristics were determined. For the mechanical properties, impact and Vickers hardness tests were carried out. To determine the corrosion behavior, both the electrochemical impedance spectroscopy technique and by potentiodynamic polarization plots were carried out in a 3.5 wt.% NaCl solution at 25 °C. The corrosion resistance of A356 alloy was dramatically improved in sequence with the following modifications compared to the unmodified castings: Sr, Ti and B additions. This situation applies to both different cooling rates, namely die and sand casting. The increase in corrosion rate was more than 80% for all alterations of the microstructure. Additionally, charge transfer resistance was increased ten times in die cast samples, while this value was 2.5 for sand cast samples compared to the unmodified alloy. It is important to note that sand casting of the unmodified alloy was improved four times with regard to the die cast unmodified A356.

36 MATERIALS SCIENCE↗

Effect of the strain-induced melt activation (SIMA) process on the tensile properties of a new developed super high strength aluminum alloy modified by Al-5Ti-1B grain refiner

In this study, the effect of Al-5Ti-1B grain refiners and modified strain-induced melt activation process on an Al-Zn-Mg-Cu alloy was studied. The optimum level of Ti was found to be 0.1 wt.%. The specimens subjected to deformation ratio of 40% (at 300 Degree-Sign C) and various heat treatment times (10-40 min) and temperature (550-600 Degree-Sign C) regimes were characterized in this study. Reheating condition to obtain a fine globular microstructure was optimized. Microstructural examinations were conducted by optical and scanning electron microscopy coupled with an energy dispersive spectrometry. The optimum temperature and time in strain-induced melt activation process are 575 Degree-Sign C and 20 min, respectively. T6 heat treatment including quenching to room temperature and aging at 120 Degree-Sign C for 24 h was employed to reach to the maximum strength. Significant improvements in mechanical properties were obtained with the addition of grain refiner combined with T6 heat treatment. After the T6 heat treatment, the average tensile strength increased from 283 MPa to 587 and 332 MPa to 617 for samples refined with 2 wt.% Al-5Ti-1B before and after strain-induced melt activation process and extrusion process, respectively. Ultimate strength of Ti-refined specimens without SIMA process has a lower value than globular microstructure specimens after SIMA and extrusion process. - Highlights: Black-Right-Pointing-Pointer The effect of Al-5Ti-1B on the aluminum alloy produced by SIMA process was studied. Black-Right-Pointing-Pointer Al-5Ti-1B is an effective in reducing the grain and reagent fine microstructure. Black-Right-Pointing-Pointer Reheating condition to obtain a fine globular microstructure was optimized. Black-Right-Pointing-Pointer The optimum temperature and time in SIMA process are 575 Degree-Sign C and 20 min respectively. Black-Right-Pointing-Pointer UTS of globular structure specimens have a more value than Ti-refined specimens.

36 MATERIALS SCIENCE↗

Ferrite grain refinement in low carbon Cu–P–Cr–Ni–Mo weathering steel at various temperatures in the (α + γ) region

Self-designed Cu–P–Cr–Ni–Mo weathering steel was subjected to compression test to determine the mechanism of ferrite grain refinement from 750 °C to 925 °C. Optical microscopic images showed that ferrite grain size declined, whereas the ferrite volume fraction increased with increasing compression temperature. Electron backscatter diffraction patterns revealed that several low-angle boundaries shifted to high-angle boundaries, thereby generating fine ferrite grains surrounded by high-angle boundaries. Numerous low-angle boundaries were observed within ferrite grains at 750 °C, which indicated the existence of pre-eutectoid ferrite. Results showed that ferrite grain refinement could be due to continuous dynamic recrystallization at 750 °C and 775 °C, and deformation-induced ferrite transformation could be the main mechanism at 800 °C and 850 °C. Fine equiaxed ferrite grains with size ranging from 1.77 μm to 2.69 μm were produced in the (α + γ) dual-phase region. - Graphical abstract: There is a close relationship between the microstructure evolution and flow curves during deformation. Fine equiaxed ferrite grains with size ranging from 1.77 μm to 2.69 μm were achieved in the (α + γ) dual-phase region. Ferrite grain refinement could be due to continuous dynamic recrystallization at 750 °C and 775 °C, and deformation-induced ferrite transformation at 800 °C and 850 °C. The occurrence of deformation-induced ferrite transformation and continuous dynamic recrystallization can be monitored by analysis of flow curves and microstructures. Deformation-induced ferrite transformation leads to the dynamic softening in flow curve when temperature just below A{sub r3}, while the dynamic softening in flow curve is ferrite continuous dynamic recrystallization (Special Fig. 5b). - Highlights: • Compression deformation was operated at temperatures from 750 °C to 925 °C at a strain rate of 0.1 s–1, and a strain of 1.2. • Fine equiaxed ferrite grains of ~1.77–2.19 μm were obtained at 750 °C and 775 °C via continuous dynamic recrystallization. • Ferrite grain size of ~2.31–2.69 μm at 800 °C and 850 °C can be obtained by deformation-induced ferrite transformation. • With decreasing deformation temperature the average grain size of ferrite decreased while volume fraction increased. • Ferrite refinement was from deformation-induced ferrite to continuous dynamic recrystallization as temperature reduced.

36 MATERIALS SCIENCE↗