SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Circuitry has been developed for digital control of the Canopus tracker. A feasibility and demonstration breadboard has been constructed using microelectronic integrated circuits. The breadboard contains the digital circuits necessary for closed-digital logic necessary for star acquisition, particle rejection, programmable gate selection, cone angle selection, and routing of the digital roll error signal.
An asynchronous binary divider formed of an array of identical logic cells is described. Each cell includes a single bit binary subtractor and a selection gate. The array is connected to divisor, dividend, quotient and remainder registers. Divisor and dividend numbers are read into the divisor and dividend registers, respectively. The array of identical logic cells performs the division in parallel asynchronously and places the results of the division in the quotient and remainder registers for subsequent readout.
Network channels elements of data array from memory ports to processor ports using a hardware-generated binary control work. Depending on control work selected, data may be shifted in increments or transposed in each of three levels to reach appropriate processing ports. A similar arrangement with reversed wiring is used to return data from processing ports to respective memory modules. Selection gate used in network incorporates two AND gates feeding an OR gate. In some logic families the OR gate may be fabricated as a "wired OR".
The results of fault injection experiments utilizing a gate-level emulation of the central processor unit of the Bendix BDX-930 digital computer are presented. The failure detection coverage of comparison-monitoring and a typical avionics CPU self-test program was determined. The specific tasks and experiments included: (1) inject randomly selected gate-level and pin-level faults and emulate six software programs using comparison-monitoring to detect the faults; (2) based upon the derived empirical data develop and validate a model of fault latency that will forecast a software program's detecting ability; (3) given a typical avionics self-test program, inject randomly selected faults at both the gate-level and pin-level and determine the proportion of faults detected; (4) determine why faults were undetected; (5) recommend how the emulation can be extended to multiprocessor systems such as SIFT; and (6) determine the proportion of faults detected by a uniprocessor BIT (built-in-test) irrespective of self-test.
Circuit-chip area used more efficiently. Proposed gate structure selectively allows and restricts access to blocks of memory in electronic neural-type network. By breaking memory into independent blocks, gate greatly simplifies problem of reading from and writing to memory. Since blocks not used simultaneously, share operational amplifiers that prompt and read information stored in memory cells. Fewer operational amplifiers needed, and chip area occupied reduced correspondingly. Cost per bit drops as result.
Different kinds of inteference may cause problems to the proper detection and analysis of the atmospheric signals, when using VHF and UHF radars. These are separated into passive and active contributions. Passive contributions are existent in the receiving system without the radar transmitter switched on. Active contributions are due to scatter and reflection of the own transmitted radar signal from unwanted targets, which are called clutter. Of major importance to radar systems are active interference contributions. Different methods can be applied for elimination or at least suppressing unwanted effects. These are; (1) Directional filtering, i.e., applying optimum suppression of antenna sidelobes, (2) Range filtering, i.e., suppressing unwanted signals only in affected range gates, (3) selection by amplitude distributions, (4) Temporal filtering, i.e., recognizing typical temporal variations of the clutter signals, through spectral characteristics, and applying matched filters.
The influence of the nature of the composite's surface on ultrasonic polar backscatter measurements for detecting and characterizing porosity in composite laminates is studied, focusing on the effects of bleeder cloth impressions noted by Bar-Cohen (1987). The results indicate that the presence of the bleeder cloth impressions substantially influences the degree of anisotropy. It is found that, for relatively thin samples in which selective time gating is not feasible, the state of the insonified surface and the state of the back surface both influence the received signal.
This paper discusses the establishment of a Supportability Technology Development Roadmap as a guide for developing capabilities intended to allow NASA's Constellation program to enable a supportable, sustainable and affordable exploration of the Moon and Mars. Presented is a discussion of "supportability", in terms of space facility maintenance, repair and related logistics and a comparison of how lunar outpost supportability differs from the International Space Station. Supportability lessons learned from NASA and Department of Defense experience and their impact on a future lunar outpost is discussed. A supportability concept for future missions to the Moon and Mars that involves a transition from a highly logistics dependent to a logistically independent operation is discussed. Lunar outpost supportability capability needs are summarized and a supportability technology development strategy is established. The resulting Lunar Surface Systems Supportability Strategy defines general criteria that will be used to select technologies that will enable future flight crews to act effectively to respond to problems and exploit opportunities in a environment of extreme resource scarcity and isolation. This strategy also introduces the concept of exploiting flight hardware as a supportability resource. The technology roadmap involves development of three mutually supporting technology categories, Diagnostics Test & Verification, Maintenance & Repair, and Scavenging & Recycling. The technology roadmap establishes two distinct technology types, "Embedded" and "Process" technologies, with different implementation and thus different criteria and development approaches. The supportability technology roadmap addresses the technology readiness level, and estimated development schedule for technology groups that includes down-selection decision gates that correlate with the lunar program milestones. The resulting supportability technology roadmap is intended to develop a set of technologies with widest possible capability and utility with a minimum impact on crew time and training and remain within the time and cost constraints of the Constellation program
This paper discusses the establishment of a Supportability Technology Development Roadmap as a guide for developing capabilities intended to allow NASA s Constellation program to enable a supportable, sustainable and affordable exploration of the Moon and Mars. Presented is a discussion of supportability, in terms of space facility maintenance, repair and related logistics and a comparison of how lunar outpost supportability differs from the International Space Station. Supportability lessons learned from NASA and Department of Defense experience and their impact on a future lunar outpost is discussed. A supportability concept for future missions to the Moon and Mars that involves a transition from a highly logistics dependent to a logistically independent operation is discussed. Lunar outpost supportability capability needs are summarized and a supportability technology development strategy is established. The resulting Lunar Surface Systems Supportability Strategy defines general criteria that will be used to select technologies that will enable future flight crews to act effectively to respond to problems and exploit opportunities in an environment of extreme resource scarcity and isolation. This strategy also introduces the concept of exploiting flight hardware as a supportability resource. The technology roadmap involves development of three mutually supporting technology categories, Diagnostics Test and Verification, Maintenance and Repair, and Scavenging and Recycling. The technology roadmap establishes two distinct technology types, "Embedded" and "Process" technologies, with different implementation and thus different criteria and development approaches. The supportability technology roadmap addresses the technology readiness level, and estimated development schedule for technology groups that includes down-selection decision gates that correlate with the lunar program milestones. The resulting supportability technology roadmap is intended to develop a set of technologies with widest possible capability and utility with a minimum impact on crew time and training and remain within the time and cost constraints of the Constellation program.
The Lunar Surface Systems Supportability Technology Development Roadmap is a guide for developing the technologies needed to enable the supportable, sustainable, and affordable exploration of the Moon and other destinations beyond Earth. Supportability is defined in terms of space maintenance, repair, and related logistics. This report considers the supportability lessons learned from NASA and the Department of Defense. Lunar Outpost supportability needs are summarized, and a supportability technology strategy is established to make the transition from high logistics dependence to logistics independence. This strategy will enable flight crews to act effectively to respond to problems and exploit opportunities in an environment of extreme resource scarcity and isolation. The supportability roadmap defines the general technology selection criteria. Technologies are organized into three categories: diagnostics, test, and verification; maintenance and repair; and scavenge and recycle. Furthermore, "embedded technologies" and "process technologies" are used to designate distinct technology types with different development cycles. The roadmap examines the current technology readiness level and lays out a four-phase incremental development schedule with selection decision gates. The supportability technology roadmap is intended to develop technologies with the widest possible capability and utility while minimizing the impact on crew time and training and remaining within the time and cost constraints of the program.
The statistical distribution of the magnitude of the vector wind change over 0.25, 0.5, 1 and 2-h periods based on data from November 1999 through August 2001 is presented. The distributions of the 2-h u and v component wind changes are also presented for comparison. The wind changes at altitudes from 500 to 3000 m were measured using the Eastern Range network of five 915 MHz Doppler radar wind profilers. Quality controlled profiles were produced every 15 minutes for up to sixty gates, each representing 101 m in altitude over the range from 130 m to 6089 m. Five levels, each constituting three consecutive gates, were selected for analysis because of their significance to aerodynamic loads during the Space Shuttle ascent roll maneuver. The distribution of the magnitude of the vector wind change is found to be lognormal consistent with earlier work in the mid-troposphere. The parameters of the distribution vary with time lag, season and altitude. The component wind changes are symmetrically distributed with near-zero means, but the kurtosis coefficient is larger than that of a Gaussian distribution.
The spatial correlation and coherence of winds over separation distances from 8.5 to 31 km based on central Florida data from November 1999 through August 2001 are presented. The winds at altitudes from 500 to 3000 m were measured using a network of five radar wind profilers. The goal was to determine the extent to which the profilers may be considered independent data sources. Quality controlled profiles were produced every 15 minutes for up to sixty gates, each representing 101 m in altitude over the range from 130 m to 6089 m. Five levels, each containing three consecutive gates, were selected for analysis. These levels covered the range from 433 to 3059 m. The results show that the profilers are independent for features having time scales of less than one hour in the winter or two hours in the summer. This does not depend significantly on height. Because the size of the network coincides with the "spectral gap" in the boundary layer, the result also does not depend on the spacing of the profilers within the network.
A volume is scanned with a raster scan about a center of rotation using a transmitter/receiver at a selected range while gating a range window on the receiver with a selected range differential. The received signals are then demodulated to obtain signals representative of a property within the volume being scanned such as the density of a tumor. The range is varied until the entire volume has been scanned at all ranges to be displayed. An imaging display is synchronously scanned together with the raster scan to display variations of the property on the display. A second transmitter/receiver with associated equipment may be offset from the first and variations displayed from each of the transmitter/receivers on its separate display. The displays may then be combined stereoscopically to provide a three-dimensional image representative of variations of the property.
This work discusses mitigation selection and qualification techniques for Xilinx reconfigurable field programmable gate arrays (FPGAs). The aim of the paper is to provide readers with a better understanding of the engineering/reliability/project cost relationship that occurs when developing a mitigation strategy for static random access memory (SRAM)-based FPGAs.
Gating of associations of mechanosensitive Ca(2+)-selective cation co-channels in the plasmalemma of onion epidermis has a strong and unusual temperature dependence. Tension-dependent activity rises steeply as temperature is lowered from 25 degrees C to about 6 degrees C, but drops to a low level at about 5 degrees C. Under the conditions tested (with Mg2+ and K+ at the cytosolic face of outside-out membrane patches), promotion results both from more bursting at all observed linkage levels and from longer duration of bursts of co-channels linked as quadruplets and quintuplets. Co-channel conductance decreases linearly, but only modestly, with declining temperature. It is proposed that these and related mechanosensitive channels may participate in a variety of responses to temperature, including thermonasty, thermotropism, hydrotropism, and both cold damage and cold acclimation.
Integral membrane proteins perform such essential cellular functions as transport of ions, nutrients and waste products across cell walls, transduction of environmental signals, regulation of cell fusion, recognition of other cells, energy capture and its conversion into high-energy compounds. In fact, 30-40% of genes in modem organisms codes for membrane proteins. Although contemporary membrane proteins or their functional assemblies can be quite complex, their transmembrane fragments are usually remarkably simple. The most common structural motif for these fragments is a bundle of alpha-helices, but occasionally it could be a beta-barrel. In a series of molecular dynamics computer simulations we investigated self-organizing properties of simple membrane proteins based on these structural motifs. Specifically, we studied folding and insertion into membranes of short, nonpolar or amphiphatic peptides. We also investigated glycophorin A, a peptide that forms sequence-specific dimers, and a transmembrane aggregate of four identical alpha-helices that forms an efficient and selective voltage-gated proton channel was investigated. Many peptides are attracted to water-membrane interfaces. Once at the interface, nonpolar peptides spontaneously fold to a-helices. Whenever the sequence permits, peptides that contain both polar and nonpolar amino also adopt helical structures, in which polar and nonpolar amino acid side chains are immersed in water and membrane, respectively. Specific identity of side chains is less important. Helical peptides at the interface could insert into the membrane and adopt a transmembrane conformation. However, insertion of a single helix is unfavorable because polar groups in the peptide become completely dehydrated upon insertion. The unfavorable free energy of insertion can be regained by spontaneous association of peptides in the membrane. The first step in this process is the formation of dimers, although the most common are aggregates of 4-7 helices. The helices could arrange themselves such that they formed pores capable of transporting ions and small molecules across membranes. Stability of transmembrane aggregates of simple proteins is often only marginal and, therefore, it can be regulated by environmental signals or small sequence modifications in the region of interhelical interactions. A key step in the earliest evolution of membrane proteins was the emergence of selectivity for specific substrates. Many channels could become selective if one or only a few properly chosen amino acids are properly placed along the channel, acting as filters or gates. This is a convenient evolutionary solution because it does not require imposing conditions on the whole sequence.
The Hybrid Automated Reliability Predictor (HARP) integrated Reliability (HiRel) tool system for reliability/availability prediction offers a toolbox of integrated reliability/availability programs that can be used to customize the user's application in a workstation or nonworkstation environment. HiRel consists of interactive graphical input/output programs and four reliability/availability modeling engines that provide analytical and simulative solutions to a wide host of highly reliable fault-tolerant system architectures and is also applicable to electronic systems in general. The tool system was designed at the outset to be compatible with most computing platforms and operating systems, and some programs have been beta tested within the aerospace community for over 8 years. This document is a user's guide for the HiRel graphical preprocessor Graphics Oriented (GO) program. GO is a graphical user interface for the HARP engine that enables the drawing of reliability/availability models on a monitor. A mouse is used to select fault tree gates or Markov graphical symbols from a menu for drawing.
A callosotomy patient was tested in two dual-task experiments requiring successive speeded responses to lateralized stimuli. In accord with the recent findings of Pashler, O'Brien, Luck, Hillyard, Mangun, and Gazzaniga (in press), the patient showed a robust psychological refractory period effect (PRP) responses on Task 2 were inversely related to the stimulus-onset asynchrony (SOA). However, three aspects of our data indicated that the processing limitations for the patient were different than those observed with control subjects. First, the split-brain patient did not show an increase in reaction time when the two tasks required responses from a common output system (i.e., both manual responses) in comparison to when different output systems were used (i.e., manual-vocal). Second, inconsistent stimulus-response mappings for the two tasks greatly inflated response latencies for the control subjects, but had minimal effect on the performance of the split-brain patient. Third, the consistency manipulation was underadditive with SOA for only the patient, suggesting a later bottleneck in processing following callosotomy than was observed for the control subjects. It is proposed that sectioning the corpus callosum eliminates interference resulting from competing stimulus response codes. Nonetheless, dual-task interference persists for the split-brain subject because a subcortical gate constrains when selected responses can be implemented.