Search NASA⌕ Search

SEARCH · Search NASA

Results for “Gelation Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Trichloroethylene replacements for the cleaning of silicone oil used in the internal gelation process

Silicone oil continues to be used as a gelation medium for internal gelation process. Typically, the silicone oil has been removed from the gel spheres using trichloroethylene (TCE) washes. However, TCE is no longer a viable option for large-scale operations because of environmental issues, health concerns, and disposal costs. Furthermore, during the development of a large gelation system at the Y-12 National Security Complex, two new TCE wash replacements were identified. NuSolv SOR-C and FluoSolv WS were used in a number of uranium runs and found to effectively remove silicone oil. NuSolv SOR-C was determined to be the best option.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Key properties of mixed cerium and zirconium microspheres prepared by the internal gelation process with previously boiled HMTA and urea

The internal gelation process using previously boiled hexamethylenetetramine-urea was used in exploratory study to produce CeO 2 –ZrO 2 microspheres, which can serve as a simulant for ceramic transuranic fuel particles and as a viable three-way catalyst. The calcined CeO 2 and ZrO 2 microspheres with Barrett–Joyner–Halenda (BJH) pore size and volumes of 8–10 nm and 0.19–0.20 mL/g, respectively, had many more surface cracks than their relatively smooth CeO 2 –ZrO 2 counterparts even though the BJH pore sizes and volumes of mixed oxide spheres were lower at 3 nm and 0.11–0.12 mL/g, respectively. The Brunauer–Emmett–Teller (BET) surface areas for the CeO 2 and ZrO 2 microspheres were 74 and 93 m2/g, respectively, and the BET surface areas for the mixed oxides were much greater at 155–158 m 2 /g, which should improve catalytic performance. Overall, the catalytic activity of each microsphere composition was confirmed through the oxidation of carbon monoxide.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Applying colloidal silica suspensions injection and sequential gelation to block vertical water flow in well annulus: laboratory testing on rheology, gelation, and injection

We evaluated the application of silica suspension injection and sequential gelation to block vertical water flow in the annuli of long-screened wells. First, we studied the viscosity, rheological behavior, and gelation performance of colloidal silica suspensions in batch tests. Then, we tested the injection of silica suspensions and the water flow blocking efficiency of the later formed silica gel in column and bench-scale sandbox experiments. Micron-sized fumed powder silica suspensions and nanosized silica suspensions recovered from geothermal fluids were tested in this work. Fumed silica suspensions showed shear thinning, while nanosized silica suspensions exhibited Newtonian flow behavior. During the gelation process, the nanosized silica suspension changed from a Newtonian fluid to a shear thinning fluid while increasing its overall viscosity. At comparable concentrations, the nanosized silica suspensions have much lower viscosity than that of the fumed silica suspensions. Increases in the Na + concentration and silica particle concentration in these suspensions shortened the gelation time. Silica suspension gelation in sand columns completely blocked the water flow and sustained the injection pressure up to 50 psig (344.7 kPa). A silica suspension was successfully injected into the target zone in the annulus of a bench-scale sandbox mimicking long-screened wells in the field. The silica gel formed in the annulus effectively blocked chemical transport through the gelled zone. Our research reveals that a process using silica suspension injection and sequential gelation technology is promising for blocking the vertical water flow and chemical transport through the filter pack in targeted zones within the annulus of long-screened well systems.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2009

Carbon XANES Data from Six Aerogel Picokeystones Cut from the Top and Bottom Sides of the Stardust Comet Sample Tray

Great care and a large effort was made to minimize the amount of organic matter contained within the flight aerogel used to collect Comet 81P/Wild 2 samples. Even so, by the very nature of the production process and silica aerogel s affinity for volatile organics keeping silica aerogel free from organics is a monumental task. Silica aerogel from three production batches was flown on the Stardust sample return mission. All 3 types had layered densities varying from 5mg/ml to 50 mg/ml where the densest aerogel was farthest away from the collection area. A 2 step gelation process was used to make the flight aerogel and organics used in this process were tetraethylorthosilicate, ethanol and acetonitrile. Both ammonium hydroxide and nitric acid were also used in the aerogel production process. The flight aerogel was baked at JPL at 300 C for 72 hours, most of the baking was done at atmosphere but twice a day the oven was pumped to 10 torr for hour [1]. After the aerogel was baked it was stored in a nitrogen purged cabinet until flight time. One aerogel cell was located in the SRC away from any sample collection area as a witness to possible contamination from out gassing of the space craft, re-entry gases and any other organic encounter. This aerogel was aerogel used in the interstellar collection sample tray and is the least dense of the 3 batches of aerogel flown. Organics found in the witness tile include organics containing Si-CH3 bonds, amines and PAHS. Besides organic contamination, hot spots of calcium were reported in the flight aerogel. Carbonates have been detected in comet 81P/Wild2 samples . During preflight analyses, no technique was used to analyze for carbonates in aerogel. To determine if the carbonates found in 81P/Wild2 samples were from the comet, it is necessary to analyze the flight aerogel for carbonate as well as for organics.

Wirick, S.↗
DOE OSTI2022

Three-step colloidal gelation revealed by time-resolved x-ray photon correlation spectroscopy

The gelation of PEGylated gold nanoparticles dispersed in a glycerol–water mixture is probed in situ by x-ray photon correlation spectroscopy. Following the evolution of structure and dynamics over 10 4 s, a three-step gelation process is found. First, a simultaneous increase of the Ornstein–Zernike length ξ and slowdown of dynamics is characterized by an anomalous q-dependence of the relaxation times of τ ∝q -6 and strongly stretched intermediate scattering functions. After the structure of the gel network has been established, evidenced by a constant ξ, the dynamics show aging during the second gelation step accompanied by a change toward ballistic dynamics with τ ∝ q -1 and compressed correlation functions. In the third step, aging continues after the arrest of particle motion. Our observations further suggest that gelation is characterized by stress release as evidenced by anisotropic dynamics once gelation sets in.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1997

Surface Plasmon Resonance Evaluation of Colloidal Metal Aerogel Filters

Surface plasmon resonance imaging has in the past been applied to the characterization of thin films. In this study we apply the surface plasmon technique not to determine macroscopic spatial variations but rather to determine average microscopic information. Specifically, we deduce the dielectric properties of the surrounding gel matrix and information concerning the dynamics of the gelation process from the visible absorption characteristics of colloidal metal nanoparticles contained in aerogel pores. We have fabricated aerogels containing gold and silver nanoparticles. Because the dielectric constant of the metal particles is linked to that of the host matrix at the surface plasmon resonance, any change 'in the dielectric constant of the material surrounding the metal nanoparticles results in a shift in the surface plasmon wavelength. During gelation the surface plasmon resonance shifts to the red as the average or effective dielectric constant of the matrix increases. Conversely, formation of an aerogel or xerogel through supercritical extraction or evaporation of the solvent produces a blue shift in the resonance indicating a decrease in the dielectric constant of the matrix. From the magnitude of this shift we deduce the average fraction of air and of silica in contact with the metal particles. The surface area of metal available for catalytic gas reaction may thus be determined.

Smith, David D.↗
DOE OSTI2021

Microstructural and crystallographic effects of sol-gel synthesized Ti-doped UO 2 sintered under reducing conditions

Titanium (Ti)-doped UO 2 microspheres of three different Ti concentrations (1000, 2000, and 4000 wppm) were synthesized using an internal gelation process. The microspheres were pressed into pellets, and a two-step heat treatment was applied to form monolithic cylindrical pellets with high densities (≥95%TD). Microstructure of these samples consisted of equiaxed grains with >300% increase in average grain size compared to the undoped UO 2 pellets. Secondary Ti-rich chemical phases corresponding to a liquid eutectic formed during sintering were observed at grain boundaries of UO 2 for samples doped with 4000 wppm Ti. Furthermore, these Ti-rich chemical phases were not observed in 1000 or 2000 wppm Ti samples at microscale using electron microscopy investigations. The 0.02–0.04% lower lattice parameter values for the Ti-doped UO 2 samples compared to the undoped UO 2 confirms the incorporation of Ti into the UO 2 lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2005

Aerogel Insulation Systems for Space Launch Applications

New developments in materials science in the areas of solution gelation processes and nanotechnology have led to the recent commercial production of aerogels. Concurrent with these advancements has been the development of new approaches to cryogenic thermal insulation systems. For example, thermal and physical characterizations of aerogel beads under cryogenic-vacuum conditions have been performed at the Cryogenics Test Laboratory of the NASA Kennedy Space Center. Aerogel-based insulation system demonstrations have also been conducted to improve performance for space launch applications. Subscale cryopumping experiments show the thermal insulating ability of these fully breathable nanoporous materials. For a properly executed thermal insulation system, these breathable aerogel systems are shown to not cryopump beyond the initial cooldown and thermal stabilization phase. New applications are being developed to augment the thermal protection systems of space launch vehicles, including the Space Shuttle External Tank. These applications include a cold-boundary temperature of 90 K with an ambient air environment in which both weather and flight aerodynamics are important considerations. Another application is a nitrogen-purged environment with a cold-boundary temperature of 20 K where both initial cooldown and launch ascent profiles must be considered. Experimental results and considerations for these flight system applications are discussed.

Fesmire, James E.↗
DOE OSTI2022

Modelling Development in Radical (Co)Polymerization of Multivinyl Monomers

Radical polymerization (RP) of multivinyl monomers (MVMs) provides a facile solution for manipulating polymer topology and has received increasing attention due to their industrial and academic significance. Continuous efforts have been made to understand their mechanism, which is the key to regulating materials structure. Modelling techniques have become a powerful tool that can provide detailed information on polymerization kinetics which is inaccessible by experiments. Many publications have reported the combination of experiments and modelling for free radical polymerization (FRP) and reversible-deactivation radical polymerizations (RDRP) of MVMs. Herein, a minireview is presented for the most important modelling techniques and their applications in FRP/RDRP of MVMs. This review hopes to illustrate that the combination of modelling and wet experiments can be a great asset to polymer researchers and inspire new thinking for the future MVMs experiment optimization and product design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2006

Aerogel/Particle Composites for Thermoelectric Devices

Optimizing solution chemistry and the addition of titania and fumed silica powder reduces shrinkage. These materials would serve to increase thermal efficiency by providing thermal insulation to suppress lateral heat leaks. They would also serve to prolong operational lifetime by suppressing sublimation of certain constituents of thermoelectric materials (e.g., sublimation of Sb from CoSb3) at typical high operating temperatures. [The use of pure silica aerogels as cast-in-place thermal-insulation and sublimation-suppression materials was described in "Aerogels for Thermal Insulation of Thermoelectric Devices" (NPO-40630), NASA Tech Briefs, Vol. 30, No. 7 (July 2006), page 50.] A silica aerogel is synthesized in a solgel process that includes preparation of a silica sol, gelation of the sol, and drying of the gel in a solvent at a supercritical temperature and pressure. The utility of pure silica aerogel is diminished by a tendency to shrink (and, therefore, also to crack) during the gelation and supercritical-drying stages. Moreover, to increase suppression of sublimation, it is advantageous to make an aerogel having greater density, but shrinkage and cracking tend to increase with density. A composite material of the type under investigation consists mostly of titania oxide powder particles and a small addition of fumed silica powder, which are mixed into the sol along with other ingredients prior to the gelation stage of processing. The silica aerogel and fumed silica act as a binder, gluing the titania particles together. It is believed that the addition of fumed silica stiffens the aerogel network and reduces shrinkage during the supercritical-drying stage. Minimization of shrinkage enables establishment of intimate contact between thermoelectric legs and the composite material, thereby maximizing the effectiveness of the material for thermal insulation and suppression of sublimation. To some extent, the properties of the composite can be tailored via the proportions of titania and other ingredients. In particular (see figure), the addition of a suitably large proportion of titania (e.g., 0.6 g/cu cm) along with a 10-percent increase in the amount of tetraethylorthosilicate [TEOS (an ingredient of the sol)] to an aerogel component having a density 40 mg/cm3makes it possible to cast a high-average-density (>0.1 g/cm3) aerogel/particle composite having low shrinkage (2.3 percent).

Paik, Jong-Ah↗
DOE OSTI2020

Use of a Pressurized Water Treatment to Prevent Cracking of Internal Gelation Sol-Gel Microspheres

Pressurized water treatments were investigated as a means to prevent cracking of internal gelation sol-gel microspheres upon drying and heating. A batch of gelled cerium oxide microspheres was prepared, split into two samples that were processed with and without a pressurized water treatment, and dried in air at room temperature. Thermal gravimetric analysis was used to compare the mass loss profiles between the two samples and to understand volatile emissions from cerium oxide microspheres during heat treatments up to 600 °C. Microspheres that were processed without a pressurized water treatment lost approximately 4.6 times more mass upon heating than microspheres that were subjected to a pressurized water treatment. Comparison of the cracking behavior of microspheres prepared with and without a pressurized water treatment indicated that microspheres subjected to a pressurized water treatment were virtually crack-free after heat treatments. Conversely, microspheres processed without a pressurized water treatment, which is typical of traditional washing processes, exhibited extensive cracking. Analysis of residues dried from pressurized water treatment effluents indicated that hexamethylenetetramine and urea, which are excess reactants from the internal gelation process, were removed from gelled microspheres during the pressurized water treatment step. Traditional processing methods for preparing internal gelation microspheres use specific feed solution and gelation parameters to reduce subsequent cracking upon drying and heating. Results from this study indicate that more aggressive gel-forming conditions may be used to produce crack-free microspheres, if a pressurized water treatment step is included after washing and before air-drying.

cerium oxide, internal gelation, microsphere, TRIS↗
DOE OSTI2023

Orthogonal Gelations to Synthesize Core–Shell Hydrogels Loaded with Nanoemulsion‐Templated Drug Nanoparticles for Versatile Oral Drug Delivery

Hydrophobic active pharmaceutical ingredients (APIs) are ubiquitous in the drug development pipeline, but their poor bioavailability often prevents their translation into drug products. Industrial processes to formulate hydrophobic APIs are expensive, difficult to optimize, and not flexible enough to incorporate customizable drug release profiles into drug products. Here, a novel, dual-responsive gelation process that exploits orthogonal thermo-responsive and ion-responsive gelations is introduced. This one-step “dual gelation” synthesizes core–shell (methylcellulose-alginate) hydrogel particles and encapsulates drug-laden nanoemulsions in the hydrogel matrices. In situ crystallization templates drug nanocrystals inside the polymeric core, while a kinetically stable amorphous solid dispersion is templated in the shell. Drug release is explored as a function of particle geometry, and programmable release is demonstrated for various therapeutic applications including delayed pulsatile release and sequential release of a model fixed-dose combination drug product of ibuprofen and fenofibrate. Independent control over drug loading between the shell and the core is demonstrated. This formulation approach is shown to be a flexible process to develop drug products with biocompatible materials, facile synthesis, and precise drug release performance. This work suggests and applies a novel method to leverage orthogonal gel chemistries to generate functional core–shell hydrogel particles.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Microfluidic Uranium Microspheres Production for TRISO and Advanced Fuel Concepts

The purpose of this project was to expand existing internal gelation sol-gel capabilities at PNNL to explore producing uranium dioxide spheres for potential use as fuel kernels in next generation Tri-isotropic (TRISO) particle fuel. This project expands on previous sol-gel efforts at PNNL by (1) increasing the size regime of sphere production from the micro-fluidic range to the milli-fluidic range, and (2) producing uranium spheres. The approach involved first scaling up the channel size of the fluidic system to the millimeter range, with radiation safety considerations in mind; testing and demonstration on non-radioactive surrogate material, cerium oxide; then transitioning to uranium production and finally optimizing system parameters. Commercially available fluidic chips in the desired size range were could not be found, therefore the project designed and fabricated a T-junction with 1mm channels for droplet production. Because the production process is temperature sensitive, prior efforts have involved performing droplet production in a lab freezer. To reduce radiological waste and footprint, two alternative chilling methods were explored using aluminum thermal beads as a chill bath and a custom aluminum block fit to reagent reservoir sizes. Both were successful in the cerium tests, however the aluminum block design outperformed the thermal bead bath and was further adapted for the radiological test and production run in the Radiochemical Processing Laboratory (RPL). Gelation trials were performed to determine an acceptable range of feed solution parameters for the uranium dioxide gels, characterized by R-values, which is determined by the ratio of uranium nitrate to Hexamethylenetetramine (HMTA)/urea in the feed solution. R-values ranging from 1.6-2 were examined in the gelation trials, with only the 1.8 condition being tested in production. The project was successful in demonstrating a proof of concept design for producing uranium dioxide spheres, however further optimization is needed to dial in production parameters and improve sphere quality and homogeneity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Time–connectivity superposition and the gel/glass duality of weak colloidal gels

Colloidal gels result from the aggregation of Brownian particles suspended in a solvent. Gelation is induced by attractive interactions between individual particles that drive the formation of clusters, which in turn aggregate to form a space-spanning structure. We study this process in aluminosilicate colloidal gels through time-resolved structural and mechanical spectroscopy. Using the time–connectivity superposition principle a series of rapidly acquired linear viscoelastic spectra, measured throughout the gelation process by applying an exponential chirp protocol, are rescaled onto a universal master curve that spans over eight orders of magnitude in reduced frequency. This analysis reveals that the underlying relaxation time spectrum of the colloidal gel is symmetric in time with power-law tails characterized by a single exponent that is set at the gel point. The microstructural mechanical network has a dual character; at short length scales and fast times it appears glassy, whereas at longer times and larger scales it is gel-like. These results can be captured by a simple three-parameter constitutive model and demonstrate that the microstructure of a mature colloidal gel bears the residual skeleton of the original sample-spanning network that is created at the gel point. Our conclusions are confirmed by applying the same technique to another well-known colloidal gel system composed of attractive silica nanoparticles. The results illustrate the power of the time–connectivity superposition principle for this class of soft glassy materials and provide a compact description for the dichotomous viscoelastic nature of weak colloidal gels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Impurity Levels in Cerium Oxide Microspheres Prepared by Internal Gelation Sol-Gel Methods

Impurity levels were measured in cerium oxide microspheres fabricated by modified internal gelation sol-gel methods. A combination of glow discharge mass spectrometry, electron impact mass spectrometry, combustion gas analysis and instrumental gas analysis were used to assess a wide range of potential elemental impurities. Low concentrations of carbon, nitrogen, and hydrogen impurities in microspheres showed a dependence on how microspheres were washed. Silicon impurities are believed to derive from silicone oil used during sol-gel processing. Spheres washed by the preferred approach had impurity levels below 100 ppm for all elements tested. For applications such as nuclear fuels, sol-gel methods could meet purity specifications as long as metal nitrate feed solutions of sufficient purity are used and microspheres are washed appropriately. In this study, cerium was used as a surrogate for plutonium-238, which is used in radioisotope power systems as a heat source, to determine whether carbon or other impurities were concentrated during internal gelation processing and remained after heat treatments. Analyses indicated low concentrations of impurities in cerium oxide microspheres after sintering steps that were well below documented limits for plutonium-238 oxide fuels. Modified washing methods, combined with a pressurized water treatment, resulted in sintered cerium oxide sol-gel microspheres with low impurity levels.

cerium oxide, sol-gel, internal gelation, microsph↗
DOE OSTI2025

Internal-Gelation Production of Uranium Oxide Sol-Gel Particles for Forensic Applications

The purpose of this project was to develop and demonstrate a novel method for the production of uranium oxide microsphere particles with tunable chemical compositions via a sol-gel process using a 3D-printer setup. These particles can serve several purposes in research and development as a forensic training tool or as standard reference materials. A key component of the project was to demonstrate the ability to control physical and chemical parameters of the particles created. First, we demonstrated the ability to employ an internal gelation sol-gel process to create individual uranium oxide particles. The particles were successfully dispensed using a unique 3D-printing setup onto a substrate to react and then were collected and thermally processed. A series of temperatures for the annealing process was tested on individual samples to investigate the effect on the sol-gel chemical composition and physical integrity. Next, we demonstrated the ability to control matrix composition of the particles by separately incorporating fission product isotopes as well as Np-237 into the sol-gel solution. It was shown by gamma-ray spectroscopy that these matrix elements were successfully retained during the gelation process. We studied the retention of the elements across a series of annealing temperatures. Additionally, we demonstrated the ability to quantitatively control the isotopic composition of the particles by altering the U-237/U-238 ratio to a controlled value. Finally, X-ray diffraction analysis (XRD) was used to investigate the oxidation state of the sol-gel after annealing at different temperatures.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗
DOE OSTI2026

Foundational insights into the mechanical and molecular evolution of porcine skin gelatin during gelation

Gelatin is a widely used material in biomedical fields, particularly in regenerative medicine and tissue engineering, due to its biocompatibility and versatile properties. While prior research has explored methods to enhance gelatin's mechanical strength and stability, fundamental studies on gelatin, specifically its curing process, mechanical stiffness, and chemical evolution during gelation, remain limited. This study uses ultrasonic testing and Fourier Transform Infrared Spectroscopy (FTIR) to examine gelatin's stiffness and molecular changes during gelation. Samples of 175 and 300 Porcine Skin Bloom Strength Gelatin at concentrations of 2% and 6% (w/v) were analyzed. Through transmission ultrasonic testing helped identify key transition points in gelation, with higher concentrations exhibiting delayed transitions. FTIR revealed that C-N bond formation peaks early while N-H bond deformation persists. A correlation emerged between sound speed and peak absorbance, suggesting that changes in molecular mobility may contribute to the observed sound speed behavior during periods of active bond formation. However, as gelation continues, fewer bonding components may be available, potentially decreasing molecular movement and contributing to the observed increase in sound speed. These findings provide insights into gelatin's mechanical and chemical evolution, offering a framework for improved control over its gelation kinetics. Swept-Frequency Acoustic Interferometry (SFAI) was performed at the end of the curing process to measure the sound speed, enabling the calculation of the bulk moduli of the gelatin samples. The combined use of ultrasonic and FTIR testing provides a non-destructive method for characterizing gelatin and other biomaterials. This approach advances understanding of gelatin curing behavior and supports the development of safer biomaterials with tailored mechanical properties for various applications such as tissue engineering and regenerative medicine.

Biomaterials↗
NASA NTRS1971

Irradiation of linear polyethylene - Partitioning between sol and gel.

Molecular weight fractions of linear polyethylene were irradiated at 133 C, in the completely molten and highly crystalline states, for the purpose of assessing the importance of chain-scission processes and establishing the critical conditions for gelation. The partitioning between sol and gel in either state was found to adhere to the theory for the intermolecular cross-linking of monodisperse species for dosages just beyond the gel point. Deviations from theory occurred as the dosage was increased further. It was concluded that main-chain scission, at these temperatures, is not a significant process. High molecular weight samples in the completely molten state obeyed the Flory-Stockmayer condition for critical gelation.

Rijke, A. M.↗