SEARCH · Search NASA

Results for “Grinding Energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Impact of anatomical fractionation of corn stover on hammer mill throughput and energy consumption

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on loss of very wet stover that causes failures in the first stage grinder and that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbohydrate content (minimum total carbohydrate specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed stover not meeting the total carbohydrate specification to the conversion reactor. Laboratory data on the impacts of moisture content and tissue fraction on throughput and energy consumption in a stage 2 hammer mill were received from FCIC Subtask 5.1. Additional air classifier throughput, energy consumption and separation efficiency data were obtained from FCIC Subtask 5.1 for the new air classifier, which has three exit streams (lights, middle and heavies). These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents and particle sizes had not been analyzed in the laboratory at the time of the model runs, we assumed that the ash distributed proportionally with total mass into the lights and heavies in an air classifier having two exit streams (lights and heavies) and that the lights fraction from the air classifier was not removed. Key takeaways from this Case Study are that due to lower energy consumption, it is more cost effective to hammer mill fractionated corn stover tissues than whole stover. Reduction of grinding energy was significant and may possibly be connected to particle-particle interactions in the grinder that lead to increased residence time of leaves and husks, resulting in decreased throughput and higher generation of fines when milling whole stover. While we did not see significant impacts to throughput, this was due to moisture failures of the first stage grinder in each system dominating failures and downtime. The operating cost savings of reduced grinding energy savings in the second stage hammer mills alone was high enough to offset the added capital cost of the air classifier and extra grinding line.

09 BIOMASS FUELS↗

DOE OSTI2025

Enhanced grindability of bastnaesite ore by ex-situ CO 2 treatment under the partial pressure of 0-100 psi

High grinding energy consumption has long constrained the sustainable development of mineral processing. This study introduces an innovative technology that employs ex-situ CO 2 treatment to enhance the grindability of bastnaesite ore. The grinding aid effect was evaluated under CO 2 partial pressures ranging from 0 psi to 100 psi using particle size distribution and the Bond work index (BWI), while the underlying mechanism was elucidated with various characterization techniques including inductively coupled plasma (ICP), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET). The optimal grinding aid effect was achieved at 100 psi partial pressure, 50% slurry concentration, and 3 h reaction duration. Correspondingly, the P80 of the grinding product decreased from 81.76 μm to 72.73 μm and the BWI of bastnaesite ore decreased from 6.96 kW·h/t to 6.30 kW·h/t, a reduction of 9.48%. The grinding aid effect primarily resulted from the transformation of sparingly soluble carbonates like calcite and dolomite into more soluble bicarbonates, which created substantial cracks and pores, thereby reducing the ore's hardness and improving its grindability. By significantly saving grinding energy consumption while delivering environmental benefits, this technology exhibits great promise for further optimization and widespread adoption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Pulsed Electric Field Processing of Apples

Pulsed electric field (PEF) processing is a nonthermal technology that has the potential to improve the efficiency of apple processing, particularly for firm cultivars that are growing in popularity. This study evaluated the effects of PEF pretreatment on the processability and product quality of Cosmic Crisp apples, a modern cultivar known for its firmness. Apples were treated with PEF and assessed for tissue softening, mechanical energy requirements, particle size reduction, browning tendencies, and juice yield. PEF treatment significantly softened the apple tissue, as demonstrated by reduced compression forces in Instron testing, and this softening translated to decreased grinding energy during applesauce production. There were no changes to the particle size distribution of the resulting applesauce. PEF treatment also altered browning behavior and produced higher juice yields following mechanical disruption, suggesting enhanced membrane permeability and mass transfer. Together, these results show that PEF pretreatment can reduce mechanical energy demands and increase extractability without reducing product quality in firm apple varieties. These outcomes highlight the potential of PEF to increase the value recovered from processing-grade apples and to support more efficient and sustainable apple processing operations.

32 - ENERGY CONSERVATION, CONSUMPTION, AND UTILIZA↗

DOE OSTI2025

Investigating the Effect of Water on the Mechanical Properties of Cellulose from Multiscale Molecular Dynamics Simulations

Classical molecular dynamics (MD) simulations provide insight into the structure and physicochemical properties of materials with atomic resolution. However, the length and time scales accessible to atomistic MD are orders of magnitude smaller than many relevant processes such as the response of a bulk material to experimentally accessible strain rates, which presents challenges when comparing models to experimental measurements. Bottom-up coarse-graining provides a means for systematically mapping atomistic information to lower resolution models to increase the length and time scales achievable by simulation. Cellulose is an abundant carbohydrate biopolymer with applications to many fields of research, such as materials science and renewable energy, due to its desirable mechanical properties and viability for conversion into biofuel. The effect of moisture content on the Young's modulus of cellulose is of special interest due to its native environment often being in the hydrated secondary plant cell wall and the grinding energy requirements for biomass feedstock preprocessing. The current work investigates the effects of water solvent on the Young's modulus of cellulose calculated from coarse-grained MD mechanical stress simulations. The coarse-grained model was parametrized from atomistic MD calculations of cellulose-cellulose potentials of mean force using umbrella sampling techniques under vacuum and solvated conditions. The Young's moduli of the coarse-grained cellulose assemblies parametrized from cellulose in vacuum or solvated in water were computed via mechanical stress simulations to highlight the importance of capturing solvent interactions for modeling the mechanical behavior of cellulose.

BASIC BIOLOGICAL SCIENCES,RADIATION PROTECTION AND↗

DOE OSTI2020

Grinding of additively manufactured silicon carbide surfaces for optical applications

Many of the properties of Silicon carbide (SiC) are advantageous for optical applications, such as telescope mirrors and industrial laser systems. However, the base shapes of complex components are costly and difficult to manufacture. Leveraging additive manufacturing, near net complex components are readily processed. In this work, we investigate the post processing of additively manufactured SiC (AM SiC) compared to chemical vapor deposited (CVD) SiC. The specific grinding energy for the AM SiC was lower than CVD, however the trends were the same. A specular finish was observed on both materials but the AM SiC finish was limited due to residual porosity.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Exploratory investigation on the use of low-cost alternative media for ultrafine grinding of coal

In this study, the energy efficiency of three alternative grinding media including, coarse silica beads, fine silica beads, and granular sand, were evaluated and compared against standard stainless steel. Stirred mill test results show that both silica beads and granular sand were more efficient than stainless steel in producing ultrafine particles following the order of coarse silica beads>granular sand>fine silica beads>stainless steel. The finest product size corresponding to a P 80 value of 2.33 μm was generated by coarse silica beads with a nominal size of 420×1190 μm, which also consumed the least amount of grinding energy. The specific energy input was reduced by almost 50% as opposed to that of stainless steel, while the operating work index was reduced by 87%. Overall, the test data indicate that grinding media density, media particle size and shape all play a role in determining the optimized grinding behavior of the coal material.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Improving bamboo’s fuel and storage properties with a net energy export through torrefaction paired with catalytic oxidation

Using torrefied char, or biocoal, as solid fuel provides an opportunity to introduce a sustainable feedstock into the energy market. The goals of this study were to investigate how torrefaction improves the energy content and the grindability of a Malaysian bamboo along with understanding the potential for integrated energy recovery from torrefaction gases. The feedstock was torrefied at 250–290 °C for 1 h and the combustion characteristics and grindability of the solid products along with the composition of torrefied gas species were measured. The results showed a beneficial increase in elemental carbon increased from 47 to 63 wt% at 290 °C torrefaction, reflecting an increase in higher heating value from 17.8 to 25.6 MJ/kg. The combustion behavior of all the products appeared to show three distinct combustion zones; however, torrefaction severity leading to higher combustion temperature and time as the fixed carbon augmented with the increase of torrefaction temperature. This increase in severity also lead to more friable and grindable material, and the 290 °C condition required a factor of 2.7 less hold-up time in the mill compared to the raw bamboo, and a factor of 8.5 less energy (938 and 111 kWh/tonne respectively). Through analysis of the gas and volatile formation, a case study showed that catalytic oxidation can convert nearly 100% of the embodied chemical energy into usable thermal energy. These experimental findings were scaled to a 100,000 tonne/y capacity torrefaction plant and in the moderate case of 270 °C operating temperature, the plant has 1.25 GJ/tonne excess energy beyond what the process needs.

09 BIOMASS FUELS↗

DOE OSTI2022

Corn Stover Fractions from Different Harvest Conditions

There is a lot of variability in biomass. This variability can make it difficult to process the biomass into a consistent format for handling and conversion. As a result, bioenergy feedstocks are often under- or over-converted. Corn stover in particular can be harvested in different ways, baled in different ways, and has significant intrinsic variability due to its very different anatomies. These factors could cause variability in the fractions of corn stover. The fractions of corn stover are leaf, husk, cob, and stalk.

09 BIOMASS FUELS↗

DOE OSTI2021

Joint influence of γ–irradiation and high temperature shear grinding on the IR spectra and surface–energy properties of polyethylene

The optical and surface-energy properties of polyethylene (PE) subjected to γ-irradiation and post-radiation, high temperature, shear grinding are presented. Comparison of the IR spectra of the initial and γ-irradiated PE shows that oxygen-containing groups and unsaturated bonds in the polymer macromolecules are formed and accumulate during their radiolysis in air, increasing with γ-irradiation dose. A redistribution of the products of radiation-chemical conversion on the surface of the polymer granules throughout the entire volume of the powder occurs after high-temperature shear milling to a powder as observed in the IR spectrum. Polar functional groups due to oxidation reactions are observed on the surface layer of the sample after post-radiation grinding. Furthermore, the initial polymer surface is weakly basic with an acidity parameter of -0.34. The value of the acidity parameter of the sample made of ground irradiated PE has an acidic surface with an acidity parameter of 0.65. γ irradiation of the secondary processing of PE waste with high-temperature shear grinding is a promising approach to obtain a secondary PE powder with specified parameters and different degrees of functionalization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Modeling Analysis of Ball-Milling Process for Battery-Electrode Synthesis

The mechanical alloying process is a promising method for synthesizing electrode materials for batteries owing to its benefits such as the ability to produce nanostructured, high-performing electrode alloys, no adverse effects on the solid electrolyte for solid-state batteries, stable production of thick electrodes, simple processing steps, and low processing costs. It is gaining intensive attention in the battery industry as one of the best methods to replace the conventional wet-slurry-solvent method, and its application is rapidly increasing these days. However, the operation is currently conducted purely based on trial-and-error methods without fully utilizing the features of its functions. Here, this may be attributed to a lack of understanding of the effect of operating parameters on the alloying process and final products. Surprisingly, there is a scarcity of the literature conducting fundamental research to comprehend the underlying physics of the entire mechanical alloying process, resulting in a significant knowledge gap. To address this knowledge gap, extensive research was conducted. The existing literature on mechanical alloying was reviewed to comprehend the current state of understanding and to discuss the direction for future research. Mathematical expressions were developed to create physics-based models capable of capturing the entire mechanical alloying process, including milling kinetics and defect-enhanced phase evolution. These methods were then applied to investigate the impact of operating parameters such as milling frequency, initial mole ratio of the alloyed materials, density of grinding balls, and energy required for the powders to become amorphous (i.e., the amorphization energy threshold). This research aimed not only to comprehend the direct effects of these operating parameters but also to unveil the physics underlying the ball-milling process. The results of our study can serve as crucial information for the battery industry in designing or operating the ball-milling process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Particle scale impacts on deconstruction energy of pine residues

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on generation of fines that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbon content (minimum carbon specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed residue not meeting both specifications to the conversion reactor. Laboratory data on the impacts of input particle size and moisture content on the exit particle size were received from FCIC Subtask 5.2 from their single particle impact population balance modeling study. Additional throughput and energy consumption data were obtained from FCIC Subtask 5.2 for the same grinder with a 6 mm screen in place. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents in the separated fines had not been analyzed in the laboratory at the time of the model runs, we chose to assume that the ash distributed proportionally with total mass into the overs and unders in the disk screen following grinding. Key takeaways from this Case Study are that it is significantly more cost effective to hammer mill the residue prior to drying, even though the grinder throughput is lower and energy consumption is higher versus drying first before grinding. An effect of dry grinding versus high moisture grinding is the production of higher amounts of fines during dry grinding, leading to significantly more of the ground feedstock being rejected by conversion for being below a minimum particle size. With wet grinding the system is still able to produce more preprocessed feedstock meeting the minimum particle size specification even though the instantaneous throughput is lower than for the case of grinding dry feedstock. Additionally, even without the higher fines production from dry grinding, the status quo would still be more costly than wet grinding because the material is rejected after the drying energy has already been input for the dry grinding case. Finally, significant reductions in drying energy are obtained by drying after grinding, and those reductions are of far greater magnitude than the grinding energy increase.

09 BIOMASS FUELS↗

DOE OSTI2020

Fabrication of lignocellulosic biomass paper containing nanofibrillated biomass

Fibrillated cellulose has been frequently used for making nanopapers and thin films. However, limited work has been carried out in the construction of such materials using native lignocellulosic biomass. Making papers from fibrillated biomass allows complete utilization of whole plant material and may reduce chemical and energy consumption. Ultra-friction grinding was used to directly fibrillate knife-milled poplar into micro- to nano-sized biomass fibers. Papers were made using the fibrillated biomass containing nanofibrillated biomass and their mechanical properties were tested. Biomass papers made via press-drying had higher tensile strength than papers made by air-drying. A higher press-drying temperature of 180 °C produced stronger papers than at 150 °C. Guar gum substantially increased the strength of the press-dried papers in comparison to cationic starch. Press-drying increased the thermogravimetric peak decomposition temperature by 13 °C in comparison to air-drying.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Particle Scale Impacts on Deconstruction Energy of Pine Residues

energy consumption↗

DOE OSTI2022

Deformation mechanism in nanolaminate FeCrAl alloys by ,em>in situ micromechanical strain rate jump tests at elevated temperatures

FeCrAl alloys have attracted extensive attention as one of the potential cladding materials for the commercial light water reactors. Although the creep behaviors of coarse-grain FeCrAl alloys have been investigated at elevated temperatures, little is known on the deformation mechanism of fine-grain FeCrAl alloys. We performed surface mechanical grinding treatment to fabricate nanolaminated ferritic FeCrAl alloys. In situ micropillar compression tests were applied to determine the underlying deformation mechanism of nanolaminated FeCrAl alloys at elevated temperatures. The strain rate sensitivity and activation energy for the dominant deformation mechanism were estimated considering the presence of a threshold stress.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Reactive Grinding of Coal Ash For Enhanced Rare Earth Extraction

Monazite and coal ash contain varying trace amounts of Rare Earth Elements (REE). Rare earth elements are considered to be the elements in the lanthanide series. These elements be categorized into two separate groups, light and heavy rare earth groups. Rare Earth Elements play an essential role to society and industry and can be found in a spectrum of applications such as Capacitors, Power Generation, and Catalysts for Petroleum Refining. Due to the abundance of Coal Ash and ongoing production, there is an increasing interest from the scientific community to develop renewable source of energy by extracting rare earth elements from within its contents. Commercial and experimental reactive grinding and leaching procedures have been created to help to maximize the recovery of Rare Earth Elements from Coal Ash.

Keller, Murphy↗

DOE OSTI2025

Developing tools and process controls to manufacture energy-efficient powders for additive manufacturing feedstocks

Traditionally, metal powders have been produced through methods such as grinding, atomization, and electrolysis. In contrast to these techniques, Metal Powder Works, Inc. has pioneered a methodology based on metal cutting. This innovative approach utilizes a vibrating cutting tool to machine metal particles, in the form of chips, from a workpiece. This technique allows for control of powder particle size, morphology, and avoids any thermally induced material changes. This collaboration aims to elucidate metal cutting characteristics and assess performance on tough materials like Inconel alloys. Computational models, using FEA and SPH techniques, will be developed initially, focusing on aluminum alloy (Al 7075- T6) for studying mesh sensitivity, cutting forces, and chip morphology.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Wind turbine blade material in the United States: Quantities, costs, and end-of-life options

Wind energy has experienced enormous growth in the past few decades; as a result, there are thousands of wind turbines around the world that will reach the end of their design lifetimes in the coming years. Much of the material in those turbines can be recycled using conventional processes, but the composite material that is the main component of the blades is more challenging to recycle. In the United States, turbine blades may be disposed of in landfills, adding a new solid waste stream to the material already being landfilled. This paper presents a spatially resolved estimate of the mass and volume of wind turbine blade waste in each state by 2050 and compares these amounts to estimates of the remaining landfill capacity by state. In this work, we estimate costs for each stage of the disposal process to indicate cost levels for alternatives. Assuming a 20-year turbine lifetime, the cumulative blade waste in 2050 is approximately 2.2 million tons. This value represents approximately 1% of remaining landfill capacity by volume, or 0.2% by mass. We also find that the current cost of disposing of blades in large segments or through grinding is relatively low in comparison to the overall life-cycle cost of energy. Based on these findings, landfill space constraints and disposal costs appear unlikely to motivate a change in waste handling strategies under current policy conditions. Instead, more profound shifts in recycling technologies, blade materials, or policy may be needed to move towards a circular economy for wind turbine blades.

17 WIND ENERGY↗

DOE OSTI2024

Toolpath generation for automated wind turbine blade finishing operations

Incorporating automation into wind turbine blade manufacturing is important for reducing costs to meet current offshore wind energy production goals in the United States. This work proposes a process for automating three operations in wind blade manufacturing: trimming to remove flashing left over after bonding two blade skins together, grinding to produce a desired leading-edge shape, and sanding to prepare the blade for bonding overlamination or adding paint to the surface. The majority of this work focuses on the toolpath generation. The algorithms were tested on a 5-m blade section, and the results were analyzed in terms of operation speed and accuracy. Finally, future work is discussed to improve the performance of the system.

17 WIND ENERGY↗