Search NASA⌕ Search

SEARCH · Search NASA

Results for “HEAT TRANSMISSION - GASES AND SOLIDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Forced-convection Heat Transfer to Water at High Pressures and Temperatures in the Nonboiling Region

Forced-convection heat-transfer data have been obtained for water flowing in an electrically heated tube of circular cross section at water pressures of 200 and 2000 pounds per square inch, and temperatures in the nonboiling region, for water velocities ranging between 5 and 25 feet per second. The results indicate that conventional correlations can be used to predict heat-transfer coefficients for water at pressures up to 2000 pounds per square inch and temperatures in the nonboiling region.

HEAT TRANSFER THEORY AND EXPERIMENT↗

Friction and Wear

From the practical point of view, this analysis shows that each problem of friction or wear requires its particular solution. There is no universal solution; one or other of the factors predominates and defines the choice of the solution. In certain cases, copper alloys of great thermal conductivity are preferred; in others, plastics abundantly supplied with water. Sometimes, soft antifriction metals are desirable to distribute the load; at other times, hard metals with high resistance to abrasion or heat.

HEAT TRANSMISSION - FLUIDS AND SOLIDS↗

Advanced Vehicle system concepts

Various nonpetroleum vehicle system concepts for passenger vehicles in the 1990's are being considered as part of the Advanced Vehicle (AV) Assessment at the Jet Propulsion Laboratory. The vehicle system and subsystem performance requirements, the projected characteristics of mature subsystem candidates, and promising systems are presented. The system candidates include electric and hybrid vehicles powered by electricity with or without a nonpetroleum power source. The subsystem candidates include batteries (aqueous-mobile, flow, high-temperature, and metal-air), fuel cells (phosphoric acid, advanced acids, and solid polymer electrolyte), nonpetroleum heat engines, advanced dc and ac propulsion components, power-peaking devices, and transmissions.

Hardy, K. S.↗

Experimental results for the rapid determination of the freezing point of fuels

Two methods for the rapid determination of the freezing point of fuels were investigated: an optical method, which detected the change in light transmission from the disappearance of solid particles in the melted fuel; and a differential thermal analysis (DTA) method, which sensed the latent heat of fusion. A laboratory apparatus was fabricated to test the two methods. Cooling was done by thermoelectric modules using an ice-water bath as a heat sink. The DTA method was later modified to eliminate the reference fuel. The data from the sample were digitized and a point of inflection, which corresponds to the ASTM D-2386 freezing point (final melting point), was identified from the derivative. The apparatus was modifified to cool the fuel to -60 C and controls were added for maintaining constant cooling rate, rewarming rate, and hold time at minimum temperature. A parametric series of tests were run for twelve fuels with freezing points from -10 C to -50 C, varying cooling rate, rewarming rate, and hold time. Based on the results, an optimum test procedure was established. The results showed good agreement with ASTM D-2386 freezing point and differential scanning calorimetry results.

Mathiprakasam, B.↗

Solid state systems concepts

Two prototype solid state phased array systems concepts for potential use in the Solar Power Satellite are described; the end-mounted and the sandwich systems. In both concepts, the beam is centered on the rectenna by means of phase conjugation of a pilot signal emanating from the ground. In the end-mounted system 36-watt amplifiers are mounted on the ground-plane, whereas in the sandwich the amplifiers are elevated to the dipoles, and their waste heat is dissipated by beryllium oxide discs. The feed lines are underneath the ground-plane, and a coaxial transmission line is carried all the way to the amplifier input. Also discussed is solid state amplifier development.

Schroeder, I. K.↗

Uncooled IR Detector

Detector combines liquid crystal film with light-sensitive solid-state array. Liquid-crystal film acts as IR detector when maintained just below temperature of transition from opacity to transparancey. When IR radiation is absorbed by film, resultant heating changes visiblelight transmission, modulating uniform visible light beam as it passes through film.

Shlichta, P. J.↗

Category 5: Sound Generation in Viscous Problems

Two problems are considered. Problem 1: Aeolian tones, sound generation by flow over cylinders, are relevant to airframe and power plant noise (heat exchanger, power transmission lines and chimneys). The purpose of this problem is to test the ability of a CFD/CAA code to accurately predict sound generation by viscous flows and sound propagation through interactions between acoustic wave & solid wall and between acoustic waves & shear layers. Problem 2: Sound generation by flow over a cavity.Air flows over the cavity shown below with a mean approach flow velocity of 50 m/s. The boundary layer that develops over the flat plate is turbulent with a thickness of 14 mm at the entrance to the cavity. Calculate the power spectra at the center of each cavit wall and the center of the cavity floor. Experimental data will be available for comparison.

Lee, Soogab↗

Experimental Studies on the Effect of Impact Processes on the Formation and Evolution of Amino Acids

Introduction: A critical step in the emergence of life on Earth was the synthesis of larger organic molecules from simple building blocks such as NH3, CO2, H2O, and CH3OH. The presence of amino acids and other complex organics in comets and meteorites demonstrates that widespread organic synthesis likely occurred across the early solar system. Building on previous work [e.g., 1-3], we systematically explore impact-driven chemical evolution of exogenous organics and their precursors. Collisional processes may also have provided a source of energy for the formation of more complex organics from endogenous building blocks. The high flux of impactors to Earth immediately prior to and during the origins of life suggests that impacts could have played a critical role. Key Questions: 1. How are the formation and evolution of amino acids affected by the presence of a mineral matrix during cometary and asteroidal impacts onto the early Earth? 2. Do some minerals (e.g., phyllosilicates) provide a more robust protective framework or reactive surface site for amino-acid formation and/or polymerization? 3. Does the abundance of ices and/or amino acids relative to that of the mineral matrix affect the formation and evolution of amino acids? 4. Are there impact velocities/shock pressures at which formation or polymerization of amino acids is favored or precluded? Experimental Approach: This study systematically examines the conditions under which amino acids and other organic molecules can form, be polymerized, and/or be destroyed during impact events into particulate regolith simulants. Variable parameters include the modal composition of this regolith (silicate matrices, ratios of ices, silicates, and amino acids) and impact velocities/shock pressures. Impacts experiments were performed using the two-stage light-gas gun (LGG), vertical gun (VG), and flat-plate accelerator (FPA) in the Experimental Impact Lab at JSC. FPA experiments were performed over a range of shock pressures (11.3-31.5 GPa) using CM chondrite simulant mixed with amino acids at ratios of 0:10, 1:10, 1:103, and 1:106 (amino acid:host). Techniques for mixing cometary ices have been optimized and test runs have been performed using the LGG (see figure below). Analysis: Post-impact, samples are heated in water to extract amino acids and peptides. Extracts are characterized via liquid chromatography-mass spectrometry (LC-MS) and the mineralogies of solid residues are characterized using X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Additional LC-MS and mineralogical analyses are underway.

Eve L Berger↗

Solar-pumped solid state Nd lasers

Solid state neodymium lasers are considered candidates for space-based polar-pumped laser for continuous power transmission. Laser performance for three different slab laser configurations has been computed to show the excellent power capability of such systems if heat problems can be solved. Ideas involving geometries and materials are offered as potential solutions to the heat problem.

Williams, M. D.↗

Light transmission and reflection in perennially ice-covered Lake Hoare, Antarctica

We have investigated the transmission and albedo of the perennial ice cover on Lake Hoare, Antarctica. Our database consists of year-round measurements of the photosynthetically active radiation (400-700 nm) under the ice, measurements of the spatial variation of the under-ice light in midsummer, and spectrally resolved measurements from 400 to 700 nm of the albedo and transmission of the ice cover in early (November) and in midsummer (January). Our results show that the transmission decreases in the first part of summer, dropping by a factor of approximately 4 from November to January. We suggest that this is due to heating in the upper layers of the ice cover and the formation of Tyndall figures. Later in the summer when a significant liquid water fraction occurs within the ice cover, the transmission increases. In the fall when the ice cover freezes solid the transmission drops markedly. The spectrally resolved measurements from 400 to 700 nm show that approximately 2-5% of the incident light in this spectral region penetrates the 3.5-m thick ice cover. We have analyzed the spectral data using a two-stream scattering solution to the radiative transfer equation with three vertical layers in the ice cover. A surficial glaze of scattering ice 1 cm thick overlies a layer of sandy, bubbly ice about a meter thick, and below this is a thick layer of sand-free ice with bubbles. We find that the ice cover is virtually opaque at wavelengths longer than 800 nm. The net transmission of solar energy is approximately 2%. Significant changes in the thickness of the ice cover have been reported at Lake Hoare. These are due primarily to changes in the thickness of the bottom layer only. Because this layer is relatively clear, the effect on the transmission through the ice cover from these changes is less than would be predicted assuming a homogeneous ice cover.

Mckay, C. P.↗

Thermochemical Stability of Ca2Yb8(SiO4)6O2 Apatite in Presence of Molten Calcium-Magnesium-AluminoSilicate (CMAS)

Thermochemical stability of ytterbium silicon oxyapatite Ca 2 Yb 8 (SiO 4 ) 6 O 2 (CYbS) in the presence of molten calcium-magnesium aluminosilicate (CMAS) has been investigated at elevated temperatures. CYbS apatite powder was synthesized from the constituent oxides via solid state reaction method. Hot pressed apatite substrates were exposed to molten CMAS at 1200, 1300, and 1400 °C for 1, 10, and 50 h. Development of phases in the interaction region of the heat-treated specimens was monitored using scanning electron microscopy, transmission electron microscopy, high angle annular dark field imaging, selected area electron diffraction and energy dispersive X-ray spectroscopy. Monoclinic cyclosilicate Ca 3 Yb 2 (Si 3 O 9 ) 2 formed from interaction of CYbS apatite with CaO in the CMAS melt at the apatite-CMAS reaction front and continued to nucleate and grow within the residual CMAS in diffusion couples annealed for 1-50 h at 1200 °C and those heat treated at 1300 °C for 1 h. Residual CMAS was Ca-depleted when cyclosilicate was present. Dendritic wollastonite CaSiO 3 was observed within the residual CMAS in couples annealed at 1200 and 1300 °C. Ingress of molten CMAS, because of its exponential decrease in viscosity, occurred through open pores and along the grain boundaries of the apatite substrates without any detectable chemical reaction at 1300 and 1400 °C. Results of this study indicate that Ca 2 Yb 8 (SiO 4 ) 6 O 2 apatite has the potential to mitigate the CMAS corrosion up to about 1200 °C but not at higher temperatures.

X-ray diffraction↗

Solid propellant combustion response to oscillatory radiant heat flux

A progress report is given on a research project to use the microwave Doppler velocimeter technique to measure the combustion response to an oscillating thermal radiation source (CO2 laser). The test technique and supporting analyses are described, and the results are presented for an initial test series on the nonmetallized, composite propellant, Naval Weapons Center formulation A-13. It is concluded that in-depth transmission of radiant heat flux is not a factor at the CO2 laser wave length.

Strand, L. D.↗

Thermochemical Stability of Ca2Yb8(SiO4)6O2 Apatite in Presence of Molten Calcium-Magnesium-Aluminosilicate (CMAS)

Thermochemical stability of ytterbium silicon oxyapatite Ca 2 Yb 8 (SiO 4 ) 6 O 2 (CYbS) in the presence of molten calcium-magnesium aluminosilicate (CMAS) has been investigated at elevated temperatures for consideration as a thermal and environmental barrier coating (T/EBC) material. CYbS apatite powder was synthesized from the constituent oxides via a solid-state reaction method. Hot-pressed apatite substrates were exposed to molten CMAS at 1200, 1300, and 1400 °C for 1, 10, and 50 h. Development of phases in the interaction region of the heat-treated specimens was monitored using scanning electron microscopy, transmission electron microscopy, high-angle annular dark-field imaging, selected area electron diffraction, and energy dispersive x-ray spectroscopy. Monoclinic cyclosilicate Ca 3 Yb 2 (Si 3 O 9 ) 2 formed from interaction of CYbS apatite with CaO in the CMAS melt at the apatite-CMAS reaction front and continued to nucleate and grow within the residual CMAS in diffusion couples annealed for 1 to 50 h at 1200 °C as well as in those heat treated at 1300 °C for 1 h. Residual CMAS was depleted of Ca when cyclosilicate was present. Dendritic wollastonite (CaSiO3) was observed within the residual CMAS in couples annealed at 1200 and 1300 °C. Ingress of molten CMAS, because of its exponential decrease in viscosity, occurred through open pores and along the grain boundaries of the apatite substrates without any detectable chemical reaction at 1300 and 1400 °C. Results of this study indicate that Ca 2 Yb 8 (SiO 4 ) 6 O 2 apatite has the potential to mitigate the CMAS corrosion up to about 1200 °C but not at higher temperatures.

Narottam P Bansal↗

TOI-3757 b: A Low-density Gas Giant Orbiting a Solar-metallicity M Dwarf

We present the discovery of a new Jovian-sized planet, TOI-3757 b, the lowest-density transiting planet known to orbit an M dwarf (M0V). This planet was discovered around a solar-metallicity M dwarf, using Transiting Exoplanet Survey Satellite photometry and confirmed with precise radial velocities from the Habitable-zone Planet Finder (HPF) and NEID. With a planetary radius of 12.0 (+0.4 -0.5) R ⊕ and mass of 85.3 (+8.8 -8.7)M ⊕ , not only does this object add to the small sample of gas giants (∼10) around M dwarfs, but also its low density (ρ=0.27 +0.05 -0.04 g) provides an opportunity to test theories of planet formation. We present two hypotheses to explain its low density; first, we posit that the low metallicity of its stellar host (∼0.3 dex lower than the median metallicity of M dwarfs hosting gas giants) could have played a role in the delayed formation of a solid core massive enough to initiate runaway accretion. Second, using the eccentricity estimate of 0.14 ± 0.06, we determine it is also plausible for tidal heating to at least partially be responsible for inflating the radius of TOI-3757b b. The low density and large scale height of TOI-3757 b makes it an excellent target for transmission spectroscopy studies of atmospheric escape and composition (transmission spectroscopy measurement of ∼ 190). We use HPF to perform transmission spectroscopy of TOI-3757 b using the helium 10830 Å line. Doing this, we place an upper limit of 6.9% (with 90% confidence) on the maximum depth of the absorption from the metastable transition of He at ∼10830 Å, which can help constraint the atmospheric mass-loss rate in this energy-limited regime.

Exoplanet astronomy↗

Solid state SPS microwave generation and transmission study. Volume 2, phase 2: Appendices

The solid state sandwich concept for SPS was further defined. The design effort concentrated on the spacetenna, but did include some system analysis for parametric comparison reasons. Basic solid state microwave devices were defined and modeled. An initial conceptual subsystems and system design was performed as well as sidelobe control and system selection. The selected system concept and parametric solid state microwave power transmission system data were assessed relevant to the SPS concept. Although device efficiency was not a goal, the sensitivities to design of this efficiency were parametrically treated. Sidelobe control consisted of various single step tapers, multistep tapers and Gaussian tapers. A hybrid concept using tubes and solid state was evaluated. Thermal analyses are included with emphasis on sensitivities to waste heat radiator form factor, emissivity, absorptivity, amplifier efficiency, material and junction temperature.

Maynard, O. E.↗

Solid state SPS microwave generation and transmission study. Volume 1: Phase 2

The solid state sandwich concept for Solar Power Station (SPS) was investigated. The design effort concentrated on the spacetenna, but did include some system analysis for parametric comparison reasons. The study specifically included definition and math modeling of basic solid state microwave devices, an initial conceptual subsystems and system design, sidelobe control and system selection, an assessment of selected system concept and parametric solid state microwave power transmission system data relevant to the SPS concept. Although device efficiency was not a goal, the sensitivities to design of this efficiency were parametrically treated. Sidelobe control consisted of various single step tapers, multistep tapers, and Gaussian tapers. A preliminary assessment of a hybrid concept using tubes and solid state is also included. There is a considerable amount of thermal analysis provided with emphasis on sensitivities to waste heat radiator form factor, emissivity, absorptivity, amplifier efficiency, material and junction temperature.

Maynard, O. E.↗