Search NASA⌕ Search

SEARCH · Search NASA

Results for “HIGH-LIFT DEVICES - COMPLETE WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

Resume of air-load data on slats and flaps

A resume of the generally available test data regarding air loads on slats and flaps is presented and data attained up to the fall of 1938 are included. The data are given in the form of N.A.C.A. standard coefficients of air forces and moments on the lift-increasing device and, when available, the aerodynamic characteristics of the combined wing and high-lift device are included. Slats of the Handley Page type, fixed auxiliary airfoils, and flaps of several different types are covered.

Wenzinger, Carl J↗
NASA NTRS1943

Wind-Tunnel Tests of an NACA 44R-Series Tapered Wing with a Straight Trailing Edge and a Constant-Chord Center Section

As part of a general investigation in the NACA 19-foot pressure tunnel to determine stall characteristics and effectiveness of high-lift devices on wings of various sections, tests were made of a tapered. wing having NACA 44R-series airfoil sections. Lift, drag, pitching-moment, and stall characteristics were determined at a Reynolds number of 4,850,000 for the plain wing and for the wing with partial-and with full-span split flaps. The stall progressed slowly over The plain wing; a gradual loss of lift for angles of attack up to and beyond that for the maximum lift coefficient resulted. As Compared with the stall of the plain wing, the initial stall of the wing with either partial-span or full-span flaps deflected occurred at a higher angle of attack and the stall progressed much more rapidly. The maximum lift coefficients at a Reynolds number of 4,850,000 were 1.35 for the plain wing, 2.25 for the wing with partial-span flaps at 60 deg, and 2.67 for the wing with full-span flaps at 60 deg. The positions of the aerodynamic center, in terms of mean chords back of the leading edge of the root section, were approximately 0.458 with no flaps, 0.483 with partial-span flaps at 60 deg, and 0.498 with full-span flaps at 60 deg.

Neely, Robert H.↗
NASA NTRS1957

Perforated Sheets as the Porous Material for a Suction-flap Application

Two-dimensional tests were made of an NACA 0006 airfoil with area suction applied to a porous region on a 0.3-chord trailing-edge flap deflected 50 degrees. The lift with suction approached the value computed from thin-airfoil theory. The lift gains and suction quantity requirements were unaffected by the perforation patterns of the surface over a wide range of hole sizes and spacings.

MATERIALS - TYPES↗
NASA NTRS1948

An Investigation of the Wing and the Wing-Fuselage Combination of a Full-Scale Model of the Republic XP-91 Airplane in the Ames 40-by 80-Foot Wing Tunnel

Wind-tunnel tests of a full-scale model of the Republic XP-91 airplane were conducted to determine the longitudinal and lateral characteristics of the wing alone and the wing-fuselage combination, the characteristics of the aileron, and the damping in roll af the wing alone. Various high-lift devices were investigated including trailing-edge split flaps and partial- and full-span leading-edge slats and Krueger-type nose flaps. Results of this investigation showed that a very significant gain in maximum lift could be achieved through use of the proper leading-edge device, The maximum lift coefficient of the model with split flaps and the original partial-span straight slats was only 1.2; whereas a value of approximately 1.8 was obtained by drooping the slat and extending it full span, Improvement in maximum lift of approximately the same amount resulted when a full-span nose flap was substituted for the original partial-span slat.

Hunton, Lynn W.↗
NASA NTRS1948

Wind-tunnel Investigation of High-lift and Stall-control Devices on a 37 Degree Sweptback Wing of Aspect Ratio 6 at High Reynolds Numbers

Results are presented of an investigation in the Langley 19-foot pressure tunnel of the longitudinal characteristics of a semispan model wing having 37 degrees sweepback of the leading edge, an aspect ratio of 6, and NACA 641-212 airfoil section perpendicular to the 27-percent-chord line. Several types of stall-control devices including extensible round-nose leading-edge flaps, a leading-edge slat, and a drooped leading edge were investigated; partial- and full-span trailing-edge split and double slotted flaps were also tested. In addition, various combinations of the aforementioned leading- and trailing-edge flaps were investigated. The tests covered a range of Reynolds numbers between 2.00 x 10(6) and 9.35 x 10(6). The wing with or without trailing-edge splity of double slotted flap was longitudinally unstable near maximum lift due to tip stalling. The addition of an outboard half-span leading-edge flap or a leading-edge slat to the plain wing or wing with inboard half-span split flaps eliminated tip stalling and resulted in stable moment variations at the stall. The drooped leading edge, on the other hand, was only effective when used in conjunction with an upper-surface fence. The combination of an outboard leading-edge device and inboard half-span double slotted flap resulted in an undesirable loop in the pitching-moment curve near maximum lift in spite of an inboard stall. The loop is attributed to the section characteristics of the double slotted flap. Air-flow surveys behind the wing indicated that a suitably placed horizontal tail would eliminate the loop in the moment curve.

Koven, William↗
NASA NTRS1941

Notes on the Stability and Control of Tailless Airplanes

Problems involved in the stability and control of tailless airplanes are discussed. Such factors as the location of the aerodynamic center and its effect on the longitudinal stability, longitudinal trim with high-lift devices, the effects of various changes in the shape of the wing on lateral stability, and the effects of nacelles are covered. It appears that sufficient stability and controllability can be secured without sweepback. With sweepback, a flap over the center section of the wing may be used to serve the dual purpose of elevator control and high-lift device. Sweepback introduces undesirable stalling characteristics, however, and may require auxiliary devices to prevent stalling of the tips.

Jones, Robert↗
NASA NTRS1934

The effects of equal-pressure fixed slots on the characteristics of a Clark Y Airfoil

A type of fixed open slot so arranged that no flow would pass through it at a lift coefficient corresponding to high-speed flight was investigated in the N.A.C.A. 7 by 10 foot wind tunnel to determine the possibilities of such a high-lift device for increasing the speed-range ratio of a wing. The condition of no through flow was achieved by locating the slot openings at points of equal static pressure at the design lift coefficient as determined from the pressure distribution about the plain wing. Two models of Clark Y wings with such equal-pressure slots were tested and the smoke-flow patterns about them observed. The results of this investigation show that the condition of no air flow through the slot at the desired lift coefficient is attainable. The surface discontinuities produced by the slot openings have, however, such a large effect on the drag that such slots show little promise. An appreciable increase is produced in the maximum lift and the speed-range can be as high as for the plain wing.

Harris, Thomas A↗
NASA NTRS1945

Summary of Airfoil Data

Recent airfoil data for both flight and wind-tunnel tests have been collected and correlated insofar as possible. The flight data consist largely of drag measurements made by the wake-survey method. Most of the data on airfoil section characteristics were obtained in the Langley two-dimensional low-turbulence pressure tunnel. Detail data necessary for the application of NACA 6-serles airfoils to wing design are presented in supplementary figures, together with recent data for the NACA 24-, 44-, and 230-series airfoils. The general methods used to derive the basic thickness forms for NACA 6- and 7-series airfoils and their corresponding pressure distributions are presented. Data and methods are given for rapidly obtaining the approximate pressure distributions for NACA four-digit, five-digit, 6-, and 7-series airfoils. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed. The data indicate that the effects of surface condition on the lift and drag characteristics are at least as large as the effects of the airfoil shape and must be considered in airfoil selection and the prediction of wing characteristics. Airfoils permitting extensive laminar flow, such as the NACA 6-series airfoils, have much lower drag coefficients at high speed and cruising lift coefficients than earlier types-of airfoils if, and only if, the wing surfaces are sufficiently smooth and fair. The NACA 6-series airfoils also have favorable critical-speed characteristics and do not appear to present unusual problems associated with the application of high-lift and lateral-control devices. Much of the data given in the NACA Advance Confidential Report entitled "Preliminary Low-Drag-Airfoil and Flap Data from Tests at Large Reynolds Number and Low Turbulence," by Eastman N. Jacobs, Ira R. Abbott, and Milton Davidson, March 1942 has been corrected and included in the present paper, which supersedes the previously published paper.

LOW-DRAG↗
NASA NTRS1936

Aerodynamic characteristics of wings with cambered external airfoil flaps, including lateral control, with a full-span flap

The results of a wind-tunnel investigation of the NACA 23012, the NACA 23021, and the Clark Y airfoils, each equipped with a cambered external-airfoil flap, are presented in this report. The purpose of the research was to determine the relative merit of the various airfoils in combination with the cambered flap and to investigate the use of the flap as a combined lateral-control and high-lift device.

Platt, Robert C↗
NASA NTRS1933

Wind-tunnel tests on model wing with Fowler flap and specially developed leading-edge slot

An investigation was made in the NACA 7 by 10 foot wind tunnel to find the increase in maximum lift coefficient which could be obtained by providing a model wing with both a Fowler trailing-edge extension flap and a Handley Page type leading-edge slot. A conventional Handley page slot proportioned to operate on the plain wing without a flap gave but a slight increase with the flap; so a special form of slot was developed to work more effectively with the flap. With the best combined arrangement the maximum lift coefficient based on the original area was increased from 3.17, for the Fowler wing, to 3.62. The minimum drag coefficient with both devices retracted was increased in approximately the same proportion. Tests were also made with the special-type slot on the plain wing without the flap. The special slot, used either with or without the Fowler flap, gave definitely higher values of the maximum lift coefficient than the slots of conventional form, with an increase of the same order in the minimum drag coefficient.

WING SLOTS & FLAPS, FOWLER↗
NASA NTRS1941

Wind-tunnel investigation of an NACA 23012 airfoil with several arrangements of slotted flaps with extended lips

An investigation was made in the NACA 7- by 10-foot wind tunnel to determine the effect of slot-lip location on the aerodynamic section characteristics of an NACA 23012 airfoil with a 30-percent-chord slotted flap. Tests were made with slot lips located at 90 and 100 percent of the airfoil chord and with two different flap shapes. The results are compared with a slotted flap previously developed by the National advisory Committee for Aeronautics with a slot lip located at 83 percent of the airfoil chord. The extension of the slot lip to the rear increased the section lift and pitching-moment coefficients. Comparisons made on a basis of pitching moment for a given tail length show that the Fowler type flap, lip extended to trailing edge of the airfoil, has the greatest section lift coefficient. For moderate tail lengths, 2 to 3 chord lengths, there was only a slight difference between the previously developed slotted flap and the slotted flap with slot lip extended to 90 percent of the airfoil chord. Of the three flaps tested, the Fowler flap had the lowest drag coefficient at high lift coefficients. The extension of the lower surface at the leading edge of the slot had a negligible effect on the profile drag of the airfoil-flap arrangement with the flap deflected when the lip terminated at 90 percent of the airfoil chord.

WING FLAPS, SLOTTED - FULL-SPAN(30%-CHORD)↗
NASA NTRS1945

Summary of Airfoil Data

The historical development of NACA airfoils is briefly reviewed. New data are presented that permit the rapid calculation of the approximate pressure distributions for the older NACA four-digit and five-digit airfoils by the same methods used for the NACA 6-series airfoils. The general methods used to derive the basic thickness forms for NACA 6 and 7-series airfoils together with their corresponding pressure distributions are presented. Detail data necessary for the application of the airfoils to wing design are presented in supplementary figures placed at the end of the paper. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed, together with aerodynamic problems of application. (author)

Abbott, Ira H↗