Search NASA⌕ Search

SEARCH · Search NASA

Results for “HULLS - RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Wind-Tunnel Tests of the 1/25-Scale Powered Model of the Martin JRM-1 Airplane. IV - Tests with Ground Board and with Modified Wing and Hull - TED No. NACA 232: Tests with Ground Board and with Modified Wing and Hull, TED No. NACA 232 - Part 4

Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity. The ground-board tests for evaluating the aerodynamic forces and moments on an airplane in a simulated cross wind indicate a high dihedral effect in the presence of the ground board and, consequently, during low-speed taxying and take-off, large overturning moments would result which would have to be overcome by the tip floats.

Lockwood, Vernard E.↗
NASA NTRS1947

Aerodynamic Characteristics of Three Deep-Stepped Planing-Tail Flying-Boat Hulls

An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of three deep-stepped planing-tail flying-boat hulls differing only in the amount of step fairing. The hulls were derived by increasing the unfaired step depth of a planing-tail hull of a previous aerodynamic investigation to a depth about 92 percent of the hull beam. Tests were also made on a transverse-stepped hull with an extended afterbody for the purpose of comparison and in order to extend and verify the results of a previous investigation. The investigation indicated that the extended afterbody hull had a minimum drag coefficient about the same as a conventional hull, 0.0066, and an angle-of-attack range for minimum drag coefficient of 0.0057 which was 14 percent less than the transverse stepped hull with extended afterbody; the hulls with step fairing had up to 44 percent less minimum drag coefficient than the transverse-stepped hull, or slightly more drag than a streamlined body having approximately the same length and volume. Longitudinal and lateral instability varied little with step fairing and was about the same as a conventional hull.

Riebe, John M.↗
DOE OSTI2022

A computationally efficient algorithm for computing convex hull prices

Electricity markets worldwide allow participants to bid non-convex production offers. While non-convex offers can more accurately reflect a resource's capabilities, they create challenges for market clearing processes. For example, system operators may be required to execute side payments to participants whose costs are not covered through energy sales as determined via traditional locational marginal pricing schemes. Convex hull pricing minimizes this and other types of side payments while providing uniform (i.e., locationally and temporally consistent) prices. Computing convex hull prices involves solving either a large-scale linear program or the Lagrangian dual of the corresponding non-convex scheduling problem. Further, the former approach requires explicit descriptions of market participants' convex hulls. While linear programs for computing convex hull prices are large, their structure is naturally decomposable by generators. Here, in this work, we propose and empirically analyze a Benders decomposition approach to computing convex hull prices that leverages recent advances in convex hull formulations for thermal generating units. We demonstrate across a large set of test instances that our decomposition approach only requires modest computational effort, obtaining solutions at least an order of magnitude faster than the equivalent large-scale linear programming approach. Overall, we provide a computationally feasible method for computing convex hull prices for industrial scale market clearing problems, enabling the possibility of practical adoption of this advanced pricing mechanism.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1978

Theoretical study of hull-rotor aerodynamic interference on semibuoyant vehicles

Analytical methods are developed to predict the pressure distribution and overall loads on the hulls of airships which have close coupled, relatively large and/or high disk loading propulsors for attitude control, station keeping, and partial support of total weight as well as provision of thrust in cruise. The methods comprise a surface-singularity, potential-flow model for the hull and lifting surfaces (such as tails) and a rotor model which calculates the velocity induced by the rotor and its wake at points adjacent to the wake. Use of these two models provides an inviscid pressure distribution on the hull with rotor interference. A boundary layer separation prediction method is used to locate separation on the hull, and a wake pressure is imposed on the separated region for purposes of calculating hull loads. Results of calculations are shown to illustrate various cases of rotor-hull interference and comparisons with small scale data are made to evaluate the method.

Spangler, S. B.↗
DOE OSTI2021

A Computationally Efficient Algorithm for Computing Convex Hull Prices

Electricity markets worldwide allow participants to bid non-convex production offers. While non-convex offers can more accurately reflect a resource's capabilities, they create challenges for market clearing processes. For example, system operators may execute side payments when a participant’s cost is not covered through energy sale settlements from locational marginal pricing schemes, or when a participant incurs lost opportunity costs to follow the dispatch signal. Convex hull pricing minimizes these and other types of side payments while providing uniform (i.e., locationally and temporally consistent) prices. However, computing convex hull prices involves solving either a large-scale linear program - which in turn requires explicit descriptions of market participants’ convex hulls -or the Lagrangian dual of the corresponding non-convex scheduling problem. Here, we propose a computationally feasible and industrially scalable Benders decomposition approach to computing convex hull prices at least an order of magnitude faster than the current state-of-the-art while leveraging recent advances in convex hull formulations for thermal generating units.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2024

Fast, Nondestructive and Precise Biomass Measurements Are Possible Using Lidar-Based Convex Hull and Voxelization Algorithms

Light detection and ranging (lidar) scanning tools are available that can make rapid digital estimations of biomass. Voxelization and convex hull are two algorithms used to calculate the volume of the scanned plant canopy, which is correlated with biomass, often the primary trait of interest. Voxelization splits the scans into regular-sized cubes, or voxels, whereas the convex hull algorithm creates a polygon mesh around the outermost points of the point cloud and calculates the volume within that mesh. In this study, digital estimates of biomass were correlated against hand-harvested biomass for field-grown corn, broom corn, and energy sorghum. Voxelization (r = 0.92) and convex hull (r = 0.95) both correlated well with plant dry biomass. Lidar data were also collected in a large breeding trial with nearly 900 genotypes of energy sorghum. In contrast to the manual harvest studies, digital biomass estimations correlated poorly with yield collected from a forage harvester for both voxel count (r = 0.32) and convex hull volume (r = 0.39). However, further analysis showed that the coefficient of variation (CV, a measure of variability) for harvester-based estimates of biomass was greater than the CV of the voxel and convex-hull-based biomass estimates, indicating that poor correlation was due to harvester imprecision, not digital estimations. Overall, results indicate that the lidar-based digital biomass estimates presented here are comparable or more precise than current approaches.

Environmental Sciences & Ecology↗
NASA NTRS1977

Theoretical study of hull-rotor aerodynamic interference on semibuoyant vehicles

Theoretical methods are being developed to predict the mutual interference between rotor wakes and the hull for semibuoyant vehicles. The objective of the investigation is to predict the pressure distribution and overall loads on the hull in the presence of rotors whose locations, tilt angles, and disk loading are arbitrarily specified. The methods involve development of potential flow models for the hull alone in a nonuniform onset flow, a rotor wake which has the proper features to predict induced flow outside the wake, and a wake centerline specification technique which accounts for the reactions of the wake to a nonuniform crossflow. The flow models are used in sequence to solve for the mutual influence of the hull and rotor(s) on each other and the resulting loads. A flow separation model is included to estimate the influence of separation on hull loads at high sideslip angles. Only limited results have been obtained to date. These were obtained on a configuration which was tested in the Ames Research Center 7- by 10-Foot Low Speed Tunnel under Goodyear Aircraft Corporation sponsorship and indicate the nature of the interference pressure distribution on a configuration in hover.

Spangler, S. B.↗
NASA NTRS1937

Hydrodynamic Tests in the N.A.C.A. Tank of a Model of the Hull of the Short Calcutta Flying Boat

The hydrodynamic characteristics of a model of the hull of the Short Calcutta (N.A.C.A. Model 47) are presented in non-dimensional form. This model represents one of a series of hulls of successful foreign and domestic flying boats the characteristics of which are being obtained under similar test conditions in the N.A.C.A. tank. The take-off distance and time for a flying boat having the hull of the Calcutta are compared at two values of the gross load with the corresponding distances and times for the same flying boat having hulls of two representative American types, the Sikorsky S-40 and the N.A.C.A. 11-A. This comparison indicates that for hulls of the widely different forms compared, the differences in take-off time and distance are negligible.

Ward, Kenneth E↗
NASA NTRS1953

Aerodynamic Characteristics of a Refined Deep-Step Planing-Tail Flying-Boat Hull with Various Forebody and Afterbody Shapes

An investigation was made in the Langley 300 mph 7-by 10-foot tunnel to determine the aerodynamic characteristics of a refined deep-step planing-tail hull with various forebody and afterbody shapes. For comparison, tests were made on a streamline body simulating the fuselage of a modern transport airplane. The results of the tests, which include the interference effects of a 21-percent-thick support wing, indicated that for corresponding configurations the hull models incorporating a forebody with a length-beam ratio of 7 had lower minimum drag coefficients than the hull models incorporating a forebody with a length-beam ratio of 5. Longitudinal and lateral stability was generally about the same for all hull models tested and about the same as that of a conventional hull.

Riebe, John M↗
NASA NTRS1924

Calculation of the hull and of the car-suspension systems of airships

Differential and integral curves are presented and well as numerous calculations relating to hulls. Some of the calculations include those relating to hulls, those relating to the invariability of the shape of the hulls, and those relating to the suspension of the hull.

AIRSHIP CARS↗
DOE OSTI2021

Reliability-based hull geometry optimisation of a point-absorber wave energy converter with power take-off structural reliability objectives

Recent studies have focused on optimising wave energy converter (WEC) designs, maximising their power performance and techno-economic feasibility. Reliability has yet to be fully considered in these formulations, despite its impact on cost and performance. In this study, this gap is addressed by developing a reliability-based design optimisation framework for WEC hull geometries to explore the trade-off between power performance and power take-off (PTO) system damage equivalent loading (DEL). Optimised hull geometries for two sites are considered (from the centre of the North Sea and off the west coast of Norway), and two directions of motions (heave and surge). Results indicate that site characteristics affect the potential power production and DEL for an optimal WEC design. These are also affected by the direction of motion for power extraction, which also significantly changes optimal hull shape characteristics. Optimal surging WEC designs have edges facing oncoming wave directions, while heaving WECs have pointed bottoms, both to streamline movement. Larger, more convex WECs result in greater power production and DEL, while smaller, more concave WECs result in lesser power production and DEL. These findings underline the importance of considering WEC hull geometry in early design processes to optimise cost, power production, and reliability.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

FOCAL Campaign IV: Integrated System Control: Turbine + Hull

Campaign IV of the Floating Offshore-wind Controls Advanced Laboratory Experimental Program (FOCAL) aimed to generate a dataset enabling the validation of a floating offshore wind turbine with turbine and hull controls. The turbine considered in this campaign is the scaled IEA 15MW Reference Wind Turbine similar to the setup considered in FOCAL Campaign I. This turbine is mounted on the VolturnUS platform with integrated hull controls similar to the hull considered in FOCAL Campaign II/III. This system is deployed for a fully-coupled wind and wave testing campaign at the University of Maine's Harold Alfond Wind and Wave (W2) facility. System dynamics and turbine characteristics are measured to determine global performance and assess the effect of the control strategies employed. NREL's reference open-source controller (ROSCO) is used for active blade pitch control and hull structural control is examined through the use of tuned mass dampers (TMD's) tuned to the systems pitch and tower-bending natural frequency. The naming convention of the load cases considered are described in the data details section. Detailed properties on the modeled system are found in the following reference: Lenfest E., Floating Offshore-wind Controls Advanced Laboratory (FOCAL) Experimental Program - Campaign IV: 1:70 Model-scale Testing of the IEA-Wind 15MW Reference Turbine and the VolturnUS-S Platform. UMaine ASCC Report Number 23-57-1183.

17 WIND ENERGY↗
NASA NTRS1946

Tank Tests of an Alternate Hull Form for the Consolidated Vultee PB2Y-3 Airplane

Tests have been made in Langley tank no. I of a dynamic model of the Consolidated Vultee PB2Y-3 airplane. These tests were made using an alternate hull form, the purpose of which was to reduce the bow spray and eliminate the landing instability which are objectionable features of the production design. The major differences from the PB2Y-3 hull included a deeper step to improve the landing stability , and a lengthened forebody and increased beam to reduce the sway in the propellers and on the flaps. The tests showed that the spray characteristics of the revised hull form were much better than that ot the production design. In addition the take-off and landing stability of the model with the alternate hull were satisfactory.

Land, Norman S.↗
DOE OSTI2023

The transcriptional activator ClrB is crucial for the degradation of soybean hulls and guar gum in Aspergillus niger

Low-cost plant substrates, such as soybean hulls, are used for various industrial applications. Filamentous fungi are important producers of Carbohydrate Active enZymes (CAZymes) required for the degradation of these plant biomass substrates. CAZyme production is tightly regulated by several transcriptional activators and repressors. One such transcriptional activator is CLR-2/ClrB/ManR, which has been identified as a regulator of cellulase and mannanase production in several fungi. However, the regulatory network governing the expression of cellulase and mannanase encoding genes has been reported to differ between fungal species. Previous studies showed that Aspergillus niger ClrB is involved in the regulation of (hemi-)cellulose degradation, although its regulon has not yet been identified. To reveal its regulon, we cultivated an A. niger ΔclrB mutant and control strain on guar gum (a galactomannan-rich substrate) and soybean hulls (containing galactomannan, xylan, xyloglucan, pectin and cellulose) to identify the genes that are regulated by ClrB. Gene expression data and growth profiling showed that ClrB is indispensable for growth on cellulose and galactomannan and highly contributes to growth on xyloglucan in this fungus. Therefore, we show that A. niger ClrB is crucial for the utilization of guar gum and the agricultural substrate, soybean hulls. Moreover, we show that mannobiose is most likely the physiological inducer of ClrB in A. niger and not cellobiose, which is considered to be the inducer of N. crassa CLR-2 and A. nidulans ClrB.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1925

Hulls for Large Seaplanes

In reality, the principle of similitude is not applicable to the hulls, the designing of which increases in difficulty with increasing size of the seaplanes. In order to formulate, at least in a general way, the basic principles of calculation, we must first summarize the essential characteristics of a hull with reference to its gradual enlargement. In this study, we will disregard hulls with wing stubs, as being inapplicable to large seaplanes.

HULLS - DESIGN↗
DOE OSTI2026

FOCAL Campaign II/III: Applying Active Hull Controls Using Tuned-mass Dampers/Hull Flexibility and Internal Loads

Campaign II and III of the Floating Offshore-wind Controls Advanced Laboratory Experimental Program (FOCAL) aimed to generate a dataset enabling the validation of the performance and loads of a scaled hull, with and without structural hull control. The floating platform was subjected to a variety of wave environments and controlled using tuned-mass dampers (TMDs) tuned to two of the systems natural frequencies (Platform Pitch and Tower-bending). The floating platform is fully instrumented to record a variety of parameters in real time such as platform dynamics, accelerations, and loads at different points in the structure. The test data considered was generated at the University of Maine's Harold Alfond Wind and Wave (W2) testing facility. This testing was focused only on validation of wave loading, and wind conditions were not considered. As such the platform does not support a working turbine, and instead supports a structure designed to have the same mass properties as the 1:70 IEA 15MW Reference turbine. The Load Cases (LC) considered in this testing campaign are as follows: LC 1.X - Platform Static Offset (TMD off); LC 2.X - Platform Free-decays (TMD off); LC 3.X - Wave Cases (Regular Wave, Irregular Wave, Pink Noise Wave) with and without TMDs active. Detailed properties on the model system are found in the following reference: Lenfest E., Floating Offshore-wind Controls Advanced Laboratory (FOCAL) Experimental Program - Campaigns 2 and 3: 1:70 Model-scale Testing of the IEA-Wind 15MW Reference Turbine and the VolturnUS-S Hull. UMaine ASCC Report Number 23-56-1183.

17 WIND ENERGY↗
NASA NTRS1984

Walnut Hulls Clean Aluminum

Hulls inflict minimal substrate damage. Walnut hulls found to be best abrasive for cleaning aluminum surfaces prior to painting. Samples blasted with walnut hulls showed no compressive stress of surface.

Colberg, W. R.↗