SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thermodynamic calculations show that hydrogen, recently detected in Io's ionosphere by the Galileo spacecraft, can degas from high-temperature silicate magmas on Io in the form of H2O, H2S, HS, NaOH, H2, KOH, and HCl in order of decreasing abundance.
Negative muon depolarization in muonic atoms in C, Mg, water, toluene, paraffin and polyethylene determined from precession measurement of muon electron decay asymmetry
Carbon compounds (CO and CO2) and methane are added to an existing computer program (Shimazaki and Laird, 1970, 1972), which calculates diurnal variations in density distributions of pure oxygen compounds, hydrogen compounds, and nitrogen compounds. For the present model calculations, the original program was modified to calculate the steady-state profiles for all constituents, and then these solutions were used as the initial condition for solving the time-dependent equations. The effects of chemical reactions and vertical eddy diffusion transport on the CH4 and CO concentrations above 40 km, where one-dimensional treatment may not be too inappropriate, are discussed. Some of the 15 constituents included in the computer program interact with CO and CH4 chemically, and CH4 is more sensitive to the eddy diffusion coefficient than any other constituent. Therefore it is easier to determine the most appropriate profile of the eddy diffusion coefficient by comparing the model profile with the observations for CH4.
Fluorocarbon-based rubber (FKM) compounds are typically utilized in the aeronautical industry due to its exceptional chemical and thermal resistance and recently has drawn significant interest from the hydrogen community for various hydrogen applications, but there exists little data evaluating its hydrogen compatibility. In this paper, a formulated FKM compound was exposed to ultrahigh hydrogen pressure (90 MPa) and analyzed by attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy and crosslinking densities by solvent swelling measurement. ATR-FTIR spectroscopic data demonstrated that high-pressure hydrogen not only caused cleavages in polymer backbone and cross linkages, but also induced additional degradation of FKM compounds by breaking intermolecular hydrogen bonding between carboxylic acids, which were produced during rubber molding and post curing processes. This hydrogen pressure-driven degradation was significantly higher towards the core of the material than at the surface due to its weaker bonding between polymers and fillers.
Weld quality relationship to aluminum surface contamination by hydrogen-containing compounds
The use of Hydrogen (H) isotopes in understanding oil and gas resource plays is in its infancy. Described here is a technique for H isotope analysis of organic compounds pyrolyzed from oil and gas shale-derived kerogen. Application of this technique will progress our understanding. This work complements that of Pernia et al. (2013, this meeting) by providing a novel method for the H isotope analysis of specific compounds in the characterization of kerogen extracted by analytically diverse techniques. Hydrogen isotope analyses were carried out entirely "on-line" utilizing a CDS 5000 Pyroprobe connected to a Thermo Trace GC Ultra interfaced with a Thermo MAT 253 IRMS. Also, a split of GC-separated products was sent to a DSQ II quadrupole MS to make semi-quantitative compositional measurements of the extracted compounds. Kerogen samples from five different basins (type II and III) were dehydrated (heated to 80 C overnight in vacuum) and analyzed for their H isotope compositions by Pyrolysis-GC-MS-TC-IRMS. This technique takes pyrolysis products separated via GC and reacts them in a high temperature conversion furnace (1450 C) which quantitatively forms H2, following a modified method of Burgoyne and Hayes, (1998, Anal. Chem., 70, 5136-5141). Samples ranging from approximately 0.5 to 1.0mg in size, were pyrolyzed at 800 C for 30s. Compounds were separated on a Poraplot Q GC column. Hydrogen isotope data from all kerogen samples typically show enrichment in D from low to high molecular weight compounds. Water (H2O) average deltaD = -215.2 (V-SMOW), ranging from -271.8 for the Marcellus Shale to -51.9 for the Polish Shale. Higher molecular weight compounds like toluene (C7H8) have an average deltaD of -89.7 0/00, ranging from -156.0 for the Barnett Shale to -50.0 for the Monterey Shale. We interpret these data as representative of potential H isotope exchange between hydrocarbons and sediment pore water during formation within each basin. Since hydrocarbon H isotopes readily exchange with water, these data may provide some useful information on gas-water or oil-water interaction in resource plays, and further as a possible indicator of paleo-environmental conditions. Alternatively, our data may be an indication of H isotope exchange with water and/or acid during the kerogen isolation process. Either of these interpretations will prove useful when deciphering H isotope data derived from kerogen analysis. More experiments are planned to discern these two or other possible scenarios.
The major chemical effluents of either solid- or liquid-fueled rockets that can potentially perturb stratospheric ozone include chlorine compounds (HCl), nitrogen compounds (NO(x)), and hydrogen compounds (H2 and H2O). Radicals (Cl, ClO, H, OH, HO2, NO, and NO2) formed directly or indirectly from rocket exhaust can cause the catalytic destruction of ozone. Other exhaust compounds that could presumably lead to ozone destruction either by direct reaction with ozone or by providing a surface for heterogeneous processes include the particulates Al2O3, ice, and soot. These topics are discussed in terms of the possible effects of rocket exhausts on stratospheric ozone.
Explore the source record for details and available documents.
The stability of various atmospheres on Titan and the Galilean satellites is examined relative to escape. One method consists of the comparison of exospheric temperature and a blow-off temperature defined for the various constituents. Another method consists of the evaluation of outflow based on a polytropic model. Hydrogen, methane, nitrogen, and neon atmospheres are examined. It is found that the Jovian satellites require heavier gases if they are to have any but very tenuous atmospheres, since all constituents examined are unstable. Nitrogen is stable on Titan, but methane and neon are marginally stable. Hydrogen is extremely unstable as a major constituent. As a minor constituent it is rapidly lost from Titan's thermosphere and must be replenished by outgassing or dissociation of a hydrogen compound, if the presently observed hydrogen content on Titan is not a transient occurrence. The rate of loss may be limited by diffusion, but could be augmented by vertical convection.
Electrocatalytic hydrogenation is increasingly studied as an alternative to integrate the utilization of recycled carbon feedstocks with renewable energy sources. However, the abundant empiric observations available have not been correlated with fundamental properties of substrates and catalysts. In this paper, we investigated the electrocatalytic hydrogenation of homologues series of carboxylic acids, ketones, phenolics, and aldehydes on a variety of metals (Pd, Rh, Ru, Cu, Ni, Zn, and Co). We found that the rates of carbonyl reduction in aldehydes correlate with the corresponding binding energies between the aldehydes and the metals according to the Sabatier principle. That is, the highest rates are obtained at intermediate binding energies. The rates of H 2 evolution, occurring in parallel to hydrogenation, also correlate with the H-metal binding energies, following the same Volcano-type behavior. Within the boundaries of this model (e.g., compounds reactive at room temperature and without important steric effects over the carbonyl group), the reported correlations help to explain the complex trends derived from the experimental observations, allowing for the correlation of rates with binding energies and the differentiation of mechanistic routes.
Hydrogen, and hydrogen compounds with oxygen, carbon, nitrogen, and phosphorus in construction of living systems
Electrocatalytic hydrogenation is a particularly attractive approach for converting the most unstable compounds in biogenic feedstocks at ambient conditions without external hydrogen. Here, we synthesized a variety of carbon-supported transition metal catalysts and characterized their activity for the electrocatalytic hydrogenation of a series of model compounds and pyrolysis oil. Carbonyl compounds, especially aromatic aldehydes, such as furfural and benzaldehyde, are particularly inclined to hydrogenation driven by an applied current. This was verified with pure solutions of the model compounds and with pyrolysis oil, where we achieved stable and steady continuous operation on Pd. By choosing the optimal catalyst composition, the conversion of benzaldehyde shifted from alcohol production (e.g., on Pd and Cu) to dimerization (e.g., on Co, Ni, and Zn). Pd and Cu were shown to offer the best compromise between reaction rates and efficiency although, in general, base metals offer similar conversions but better efficiencies that noble metals. Thus, the present work offers foundational results and guidelines for choosing the optimal metal catalyst and the applied potential for processing organic feedstocks as a function of its composition.
A hydrogenation catalyst including a base material coated with a catalytic metal is made using mechanical milling techniques. The hydrogenation catalysts are used as an excellent catalyst for the dehalogenation of contaminated compounds and the remediation of other industrial compounds. Preferably, the hydrogenation catalyst is a bimetallic particle including zero-valent metal particles coated with a catalytic material. The mechanical milling technique is simpler and cheaper than previously used methods for producing hydrogenation catalysts.
A hydrogenation catalyst including a base material coated with a catalytic metal is made using mechanical milling techniques. The hydrogenation catalysts are used as an excellent catalyst for the dehalogenation of contaminated compounds and the remediation of other industrial compounds. Preferably, the hydrogenation catalyst is a bimetallic particle including zero-valent metal particles coated with a catalytic material. The mechanical milling technique is simpler and cheaper than previously used methods for producing hydrogenation catalysts.
Synthesis and characterization of chemical analogues of TATB, where specific atoms in the structure have been isotopically substituted, are reported. 15 N, 2 H, and 18 O have replaced the naturally occurring isotope distributions in the amino and/or the nitro attendant sites and 13 C has replaced the carbon in the ring structure. A modified wet-amination method was used to produce the analogues, and the isotopic replacements were performed by selective choice of labeled precursors. Four 15 N-labeled compounds (N replaced in the amino and nitro positions), two deuterium-labeled compounds (hydrogens replaced on the amino groups), and one 13 C-labeled compound (C in the ring substituted) were synthesized of high isotopic and chemical purity. One partially labeled 18 O-labeled compound (O in the nitro position) was a result of incomplete labeling due to exchange reactions during synthesis. The compounds were characterized by various spectroscopic methods – mass spectrometry (MS), solid-state nuclear magnetic resonance (SS-NMR), infrared (FTIR), powder x-ray diffraction (PXRD), and differential scanning calorimetry (DSC), depending upon the substitution. In conclusion, these compounds have been critical to the efforts in understanding the decomposition pathways of TATB when exposed to abnormal thermal environments.
In an earlier paper, Khare and Sagan reported the production of a brownish polymeric material from the near-ultraviolet irradiation of simulated jovian atmospheres with a low hydrogen abundance. Examination of this product indicates that hydrogen sulfide is the initial photon acceptor; the powder resulting after extraction with benzene is 84 percent sulfur, largely S8. In results reported here, the remaining 16 percent was pyrolyzed and then examined by gas chromatography-mass spectrometry. Pyrolysis at 450 C yielded a series of alkanes, alkenes, C3-alkylbenzenes, aromatics, thiophenes, alkylthiophenes, alkylmercaptans, alkyldisulfides, together with the nitrogenous compounds hydrogen cyanide, methyl cyanide, alkylisothiocyanates, acrylonitrile, and allylisothiocyanates. Some of these compounds might be sought on Jupiter and Saturn and their satellites by remote infrared and ultraviolet spectroscopy and directly by entry probes.
The hydrogen photoelectrolytic conversion activity investigated the practicability of semiconductor electrolytic devises that use solar energy to decompose water into hydrogen and oxygen in an apparent single step process. The photocatalytic decomposition of inorganic hydrogen compounds; i.e., hydrobromic and hydriodic acids using rhodium organic bridge complexes were also studied. The feasibility of direct high temperature thermal decompositions of water with diffusion processes for separation of the equilibrium mixture of hydrogen and oxygen into usable energy sources was examined.