Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hard magnetic properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Microstructural evolutions, phase transformations and hard magnetic properties in polycrystalline Ce–Co–Fe–Cu alloys

This work focuses on systematic studies of Ce–Co based 1:5 permanent magnet alloys of CeCo 4.4-x Fe x Cu 0.6 and CeCo 3.9-x Fe x Cu 1.2 (x = 0, 0.3, 0.6, 0.9, 1.2, 1.8) by varying Co:Fe. The overarching aim of this manuscript is to elucidate the hard-magnetic properties through a better understanding of phase formation by the structural, microstructural, and magnetic properties in these materials. Improved mutual solubility of Fe in the 1:5 phase has been observed with an extended homogeneity range by Cu substitution. For both composition series, Fe contents of x ≤ 0.6 show a homogeneous microstructure with a single 1:5 phase and good magnetic properties. The composition region 0.6 < x ≤ 0.9 appears to be near the boundary of solubility and evolution of other phases. At x = 1.8, it is found that the homogeneous 1:5 phase and magnetic hardness deteriorated due to the evolution of secondary phases such as 2:17, 2:7, and Fe–Co. Furthermore, the addition of Fe improved both the magnetization and Curie temperature via increased effective exchange interactions, while an increase in Cu content enhanced coercivity.

33 ADVANCED PROPULSION SYSTEMS↗

Intrinsic and hard magnetic properties of (Sm 1-x R x )-Fe-Co-V alloys (R = Gd, Zr, and Y)

SmFe 12 -based compounds with the ThMn 12 -type structure have a great potential as future rare-earth-lean permanent magnets. However, their reliance on stabilizing non-magnetic elements has impeded practical applications. Therefore, elements such as Gd, Y, and Zr have gained popularity as candidates to minimize the need for stabilizing elements by reducing the formation energy of the ThMn 12 (1:12) phase. Here, this study examines the effect of Gd, Y, and Zr on the intrinsic and hard magnetic properties in (Sm 1-x R x ) 1.2 Fe 8.4 Co 2.1 V 1.5 (or with nominal composition of (Sm 1-x R x ) 9.1 Fe 63.6 Co 15.9 V 11.4 ) with a single 1:12 phase for 0 ≤ x ≤ 0.3. Notably, samples substituted with Gd exhibit an enhanced temperature dependence of the magnetic properties.

36 MATERIALS SCIENCE↗

Effect of vanadium on phase composition and hard magnetic properties of as-solidified and heat-treated Sm–Fe–(Ti,V) alloys

Although the intrinsic magnetic properties of Ti-stabilized Sm(Fe,Co,Ti) 12 compounds exhibit potential of excellent rare-earth-lean permanent magnets, it has been much easier to realize large coercivities with the isostructural compounds stabilized by either V or by certain combinations of Ti and V. To elucidate the influence of V on the microstructure and magnetic properties, a series of Sm 8.1 Fe 78.4 (Ti 1-x V x ) 13.5 alloys was studied after arc-melting and annealing at 850–1000 °C. The alloys were found to fall into three groups. For x ≤ 0.2, solidification generates mostly the Sm(Fe,Ti,V) 12 phase, but annealing converts at least part of it into the non-magnetic Sm(Fe,Ti,V) 11 and the magnetically soft Sm 2 (Fe,Ti,V) 17 phases. For 0.2 < x < 0.6, the alloys solidify into a near-equilibrium mixture of the Sm(Fe,Ti,V) 12 , TiFe 2 and Sm-rich phases. For x ≥ 0.6, solidification generates large fractions of α-Fe solid solution and Sm-rich phases; an annealing step is necessary to complete the formation of Sm(Fe,Ti,V) 12 phase. Also, for x ≥ 0.6 the temperature below which the Sm(Fe,Ti,V) 12 phase is stable decreases with x, as does the fraction of this phase formed during solidification. Here, the differences between these three groups of alloys suggest different strategies for developing hard magnetic properties, with the likelihood of a success increasing with increasing x. For x ≥ 0.6, heat treatment alone is demonstrated to generate a microstructure of micron and submicron Sm(Fe,Ti 1-x V x ) 12 crystallites separated by a Sm-rich phase and exhibiting a coercivity with values up to 3.5 and 5.7 kOe for x = 0.8 and 1.0, respectively.

36 MATERIALS SCIENCE↗

Effects of magnetic field annealing on the hard magnetic properties of milled Nd-Fe-B powders

In this study, we report the effect of magnetic field annealing (MA) in relieving the stress induced during the milling of Nd-Fe-B sintered magnets. The effect of MA processing parameters and particle size on the magnetic properties were investigated. Based on the results, magnetic field annealing is more effective in improving the magnetic properties of larger size particles, compared to finer particles. Our computational study on the role of particle surface defects in bi-modal particle distribution agrees with results obtained experimentally. In conclusion, magnetic field annealed powder has been successfully used to develop 4.6 g.cm -3 density bonded magnets with 75 vol% of magnetic powder and polyamide 12 (nylon 12) polymer binder resulting in 11.3 MGOe energy product.

36 MATERIALS SCIENCE↗

Coercivity of (Fe 0.7 Co 0.3 ) 2 B Nanowire and Its Bonded Magnet

(Fe 0.7 Co 0.3 ) 2 B are potential permanent magnets material due to its large saturation magnetization and high Curie temperature. However, it has moderate magnetocrystalline anisotropy (MCA) and low coercivity. One way to improve its coercivity is to combine the contributions from magnetocrystalline- and magnetic-shape anisotropy by preparing (Fe 0.7 Co 0.3 ) 2 B nanowires. We study the effects of size, morphology, and surface defects on the hard magnetic properties of nanowires using micromagnetic simulation. The hard magnetic properties of (Fe 0.7 Co 0.3 ) 2 B nanowire-bonded magnets are estimated, including the role of inter-wire magnetostatic interaction. By considering the existence of local reductions in MCA energy of up to 30% on the surface layer of nanowires, the anisotropic bonded magnet with a 65% vol. of (Fe 0.7 Co 0.3 ) 2 B nanowires would have typical remanence, B r = 7.6–8.4 kG, coercivity, H ci = 9.6–9.9 kOe, and maximum energy product, (BH) m = 14–17.8 MGOe. Developing effective technology for synthesizing nanowires and fabricating corresponding bonded magnets is promising for manufacturing practical magnets based on the magnetic phase with a relatively low or moderate MCA, such as (Fe 0.7 Co 0.3 ) 2 B.

36 MATERIALS SCIENCE↗

Semihard magnetic properties of TiFe 2.5 iron-rich Laves phase and the effect of 4d- and 5d-element-substitutions for Ti

Rare-earth-free compounds exhibiting modest intrinsic hard magnetic properties may still yield viable permanent magnets if their constituent elements are abundant and inexpensive, and the properties are at least comparable to those of the hard ferrites. In this study, one such compound, the off-stoichiometric TiFe 2.5 Laves phase with the hexagonal C14 crystal structure, was found to exhibit – in addition to the already known room-temperature ferromagnetism – a uniaxial, albeit weak, magnetic anisotropy. With a Curie temperature of 422 K, saturation magnetization of 55.3 Am 2 /kg and magnetic hardness parameter of 0.97 this semihard compound is just below the threshold for being of interest for the development into permanent magnets. Replacing a small fraction of Ti with the 4d Nb and Mo or with the 5d Ta or W increases the anisotropy field, but only below room temperature. Replacing Ti with Zr or Hf increases the Curie temperature and leads to a spin reorientation below 200 K. All these substitutions, as well as combined (Zr,W) and (Nb,W) substitutions, fail to improve the room-temperature intrinsic hard magnetic properties of the Fe-rich Laves phase. Furthermore, an attempt to develop a room-temperature coercivity through high-energy ball-milling yielded a value of 0.026 T, an unusually small 2.9% fraction of the anisotropy field. Here, defects inherent in the C14 crystal lattice may be responsible for the underperformance.

36 MATERIALS SCIENCE↗

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗

Enhancement of hard magnetism and chemical order of synthetic L 1 0 -FeNi

An ordered tetragonal L 1 0 -FeNi, also known as meteoritic mineral tetrataenite – a promising rare-earth-free hard-magnetic compound – has been synthesized starting from a mechanochemically-activated disordered cubic A1-FeNi via formation of a chemically-ordered FeNiN intermediate and its subsequent denitrogenation and further purification of the product. The nature of a process control agent employed during the mechanochemical activation of A1-FeNi and ammonia flow velocity during the synthesis of the intermediate are two of the main factors controlling the nitrogenation. Denitrogenation with hydrogen at elevated pressures and at temperatures substantially below the order-disorder L 1 0 -FeNi → A1-FeNi transition preserves the chemical order established in the intermediate nitride. Further, post-synthesis refinement of the L 1 0 -FeNi product includes the removal of residual nitrides with a dilute acid to further improve hard-magnetic properties of the material. The L 1 0 -FeNi powders synthesized using this method exhibit a coercivity as high as 2.3 kOe and a maximum energy product reaching 6 MGOe – the highest values ever reported for a synthetic tetrataenite.

36 MATERIALS SCIENCE↗

Minimizing particle aggregation in Sm 2 Fe 17 N 3 powders: A CaO-assisted reduction-diffusion approach

We report a novel synthesis of Sm 2 Fe 17 N 3 powders using a CaO-assisted reduction-diffusion (RD) approach. CaO plays a crucial role during mechanochemical processing – acting both as a dispersant and a surface coating agent, which helps to prevent agglomeration due to sintering of Sm 2 Fe 17 particles during the RD step. Together with the added dispersant, the CaO by-product formed during RD can be easily removed in the washing step resulting in fewer aggregated Sm 2 Fe 17 N 3 particles and lower oxygen contamination in the final product. The impact of varying CaO amounts was examined, and synthesis conditions were optimized to achieve phase-pure Sm 2 Fe 17 N 3 powders with less aggregation of magnetic particles. The powders synthesized with addition of 1 wt% CaO as dispersant exhibited the highest hard-magnetic properties: a coercivity (H c ) of 10.7 kOe and a maximum energy product ((BH) max ) of 17.3 MGOe. By densifying the Sm 2 Fe 17 N 3 powders using high-pressure spark plasma sintering, a bulk magnet with a (BH) max of 21.1 MGOe with 88 % of theoretical density was produced. In conclusion, reducing aggregation of the Sm 2 Fe 17 N 3 increases coercivity and remanence of these magnets.

36 MATERIALS SCIENCE↗

Integrated ab initio modelling of atomic ordering and magnetic anisotropy for design of FeNi-based magnets

We describe an integrated modelling approach to accelerate the search for novel, single-phase, multicomponent materials with high magnetocrystalline anisotropy (MCA). For a given system we predict the nature of atomic ordering, its dependence on the magnetic state, and then proceed to describe the consequent MCA, magnetisation, and magnetic critical temperature (Curie temperature). Crucially, within our modelling framework, the same ab initio description of a material’s electronic structure determines all aspects. We demonstrate this holistic method by studying the effects of alloying additions in FeNi, examining systems with the general stoichiometries Fe 4 Ni 3 X and Fe 3 Ni 4 X, for additives including X = Pt, Pd, Al, and Co. The atomic ordering behaviour predicted on adding these elements, fundamental for determining a material’s MCA, is rich and varied. Equiatomic FeNi has been reported to require ferromagnetic order to establish the tetragonal L1 0 order suited for significant MCA. Our results show that when alloying additions are included in this material, annealing in an applied magnetic field and/or below a material’s Curie temperature may also promote tetragonal order, along with an appreciable effect on the predicted hard magnetic properties.

36 MATERIALS SCIENCE↗

Bi-modal particle size distribution for high energy product hybrid Nd–Fe–B—Sm–Fe–N bonded magnets

In this work, we have demonstrated high energy product bonded magnet by leveraging the variation in sizes between Nd-Fe-B and Sm-Fe-N, as well as their hard magnetic properties. The hybrid anisotropic bonded magnets contain 70 vol% of magnet powder (Dy-free Nd-Fe-B and Sm-Fe-N) and 30 vol% of nylon. The objective of the work was to create bi-modal and bi-compositional bonded magnets in which the fine (3μm) particles of Sm-Fe-N would be used to fill the voids between the bigger Nd-Fe-B (105μm) particles, thus improve packing density. The magnetic hysteresis loop did not show significant signs of decoupled interactions between the magnetic phases. It was also found that the performance of the bonded magnet was most enhanced at 1:4 ratio of Nd-Fe-B and Sm-Fe-N. At that ratio, maximum density of 5 g/cm 3 and the highest (BH) max value of 18.5 MGOe were obtained, although the intrinsic coercivity decreased, relative to the trend seen for other ratios. This work advances the opportunity to expand the use of Sm-Fe-N in bonded magnet applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical bond and phase stability of Ga-doped Sm2Fe17Cx magnet

Sm2Fe17C3 phase (2:17) is metastable and exhibits excellent intrinsic hard magnetic properties. Doping elements such as Ga facilitate the formation of a single-phase 2:17 structure in arc-melted Sm2Fe17Cx alloys, which opens a promising route for fabricating fully dense bulk Sm2Fe17Cx magnets via high-temperature techniques such as melting and sintering. First-principles electronic structure calculation indicates that Ga prefers to partially replace Fe at the 9d and 18h crystallographic sites in Sm2Fe17C3 and Sm2Fe17, respectively. This difference in site preference is attributed to the distinct chemical environments surrounding the Fe atoms in the two compounds. Ga substitution favors the Sm–Ga bonding formation while avoiding Ga–C interactions. Doped Ga atoms result in more negative formation energy in Sm2(Fe, Ga)17C3, indicating improved structural stability. Crystal Orbital Hamilton Population analysis reveals that carbon insertion weakens the bonding of Sm-Fe (18h) and Sm-Fe (18f) in Sm2Fe17C3. Ga doping facilitates electron redistribution across chemical bonds, thereby reinforcing Fe(18h)–Sm and Fe(18f)–Sm interactions and stabilizing the carbon-centered octahedral local structure. This synergistic effect contributes significantly to the observed enhancement in phase stability of Sm2(Fe, Ga)17Cx. These findings suggest that chemical bond engineering through the selective doping of Ga can enhance phase stability and facilitate the synthesis of Sm2Fe17C3, providing a viable strategy for developing advanced magnets.

Liu, Xubo [Critical Materials Innovation Hub, Divi↗

Data for "Integrated ab initio modelling of atomic order and magnetic anisotropy for rare-earth-free magnet design: effects of alloying additions in L1 0 FeNi."

We describe an integrated modelling approach to accelerate the search for novel, single-phase, multicomponent materials with high magnetocrystalline anisotropy (MCA). For a given system we predict the nature of atomic ordering, its dependence on the magnetic state, and then proceed to describe the consequent MCA, magnetisation, and magnetic critical temperature (Curie temperature). Crucially, within our modelling framework, the same ab initio description of a material’s electronic structure determines all aspects. We demonstrate this holistic method by studying the effects of alloying additions in FeNi, examining systems with the general stoichiometries Fe 4 Ni 3 X and Fe 3 Ni 4 X, for additives including X = Pt, Pd, Al, and Co. The atomic ordering behaviour predicted on adding these elements, fundamental for determining a material’s MCA, is rich and varied. Equiatomic FeNi has been reported to require ferromagnetic order to establish the tetragonal L1 0 order suited for significant MCA. Our results show that when alloying additions are included in this material, annealing in an applied magnetic field and/or below a material’s Curie temperature may also promote tetragonal order, along with an appreciable effect on the predicted hard magnetic properties.

36 MATERIALS SCIENCE↗

Robustness of magnetocrystalline anisotropy and coercivity in Fe–Co–B

As a potential candidate for critical chemical element free permanent magnet, (Fe 0.7 Co 0.3 ) 2 B, shows promising intrinsic magnetic properties, including large magnetization, high Curie temperature and moderate magnetocrystalline anisotropy (MCA). Still, the coercivity that has been achieved is relatively low. To understand and improve coercivity, here we study the robustness of MCA related to the fluctuation of chemical composition and the structural distortion and its effect on coercivity in (Fe 0.7 Co 0.3 ) 2 B from first principles DFT (density functional theory) calculation and micromagnetic simulation. A fluctuation of cobalt content of 10%, or 1% isotropic lattice strain, or 2% tetragonal distortion reduces MCA energy up to 30%. By considering randomly distributed local MCA energy reduction up to 30%, the calculated coercivity of anisotropic bulk magnets reduced from 3.6 kOe to 2.2 kOe. Rational microstructure design, such as grain size refinement and development of strong crystal texture of MCA easy-axis (i.e., degree of alignment for (Fe 0.7 Co 0.3 ) 2 B grains), can enhance coercivity and mitigate the effect of local MCA reduction. In addition to acceptable intrinsic magnetic properties, the promising hard magnetic phase needs good MCA robustness to facilitate the development of practical magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Soil Analysis Micro-Mission Concepts Derived from the MSP 2001 Mars Environmental Compatibility Assessment (MECA)

The Mars Environmental Compatibility Assessment (MECA) will evaluate the Martian environment for soil and dust-related hazards to human exploration as part of the Mars Surveyor Program 2001 Lander. The integrated MECA payload contains a wet-chemistry laboratory, a microscopy station, an electrometer to characterize the electrostatic environment, and arrays of material patches to study abrasion and adhesion. Heritage will be all-important for low cost micro-missions, and adaptations of instruments developed for the Pathfinder, '98 and '01 Landers should be strong contenders for '03 flights. This talk has three objectives: (1) Familiarize the audience with MECA instrument capabilities; (2) present concepts for stand-alone and/or mobile versions of MECA instruments; and (3) broaden the context of the MECA instruments from human exploration to a comprehensive scientific survey of Mars. Due to time limitations, emphasis will be on the chemistry and microscopy experiments. Ion-selective electrodes and related sensors in MECA's wet-chemistry laboratory will evaluate total dissolved solids, redox potential, pH, and the concentration of many soluble ions and gases in wet Martian soil. These electrodes can detect potentially dangerous heavy-metal ions, emitted pathogenic gases, and the soil's corrosive potential, and experiments will include cyclic voltammetry and anodic stripping. For experiments beyond 2001, enhancements could allow multiple use of the cells (for mobile experiments) and reagent addition (for quantitative mineralogical and exobiological analysis). MECA's microscopy station combines optical and atomic-force microscopy (AFM) in an actively focused, controlled illumination environment to image particles from millimeters to nanometers in size. Careful selection of substrates allows controlled experiments in adhesion, abrasion, hardness, aggregation, magnetic and other properties. Special tools allow primitive manipulation (brushing and scraping) of samples. Soil particle properties including size, shape, color, hardness, adhesive potential (electrostatic and magnetic), will be determined using an array of sample receptacles and collection substrates. The simple, rugged atomic-force microscope will image in the submicron size range and has the capability of performing a particle-by-particle analysis of the dust and soil. Future implementations might enhance the optical microscopy with spectroscopy, or incorporate advanced AFM techniques for thermogravimetric and chemical analysis.

Hecht, M. H.↗

The MSP 2001 Mars Environmental Compatibility Assessment (MECA)

The Mars Environmental Compatibility Assessment (MECA) will evaluate the Martian environment for soil and dust-related hazards to human exploration as part of the Mars Surveyor Program 2001 Lander. Sponsored by the Human Exploration and Development of Space (HEDS) enterprise, MECA's goal is to evaluate potential geochemical and environmental hazards that may confront future Martian explorers, and to guide HEDS scientists in the development of high fidelity Mars soil simulants. The integrated MECA payload contains a wet-chemistry laboratory, a microscopy station, an electrometer to characterize the electrostatics of the soil and its environment, and arrays of material patches to study the abrasive and adhesive properties of soil grains. The instrument will acquire soil samples with a robotic arm equipped with a camera. MECA will examine surface and subsurface soil and dust in order to characterize particle size, shape, hardness, and also physical characteristics that may provide clues to mineralogy. MECA will characterize soil/water mixtures with respect to pH, redox potential, total dissolved ions, and trace toxins. MECA will determine the nature of electrostatic charging associated with excavation of soil, and the influence of ionizing radiation on material properties. It will also observe natural dust accumulation on engineering materials. To accomplish these objectives, MECA is allocated a mass of 10 kg within an enclosure of 35 x 25 x 15 cm. The Wet Chemistry Laboratory (WCL) consists of four identical cells that will accept samples from surface and subsurface regions accessible to the Lander's robotic arm, mix them with water, and perform extensive analysis of the solution. Ion-selective electrodes and related sensors will evaluate total dissolved solids, redox potential, pH, and the concentration of many soluble ions and gases in wet Martian soil. These electrodes can detect potentially dangerous heavy-metal ions, emitted pathogenic gases, and the soil's corrosive potential. Experiments will include cyclic voltammetry and anodic stripping voltammetry. Complementary to the Viking experiments, the chemical laboratory will characterize the water-soil solution rather than emitted gases. Nonetheless, through analysis of dissolved gases it will be able to replicate many of the Viking observations related to oxidants. MECA's microscopy station combines optical and atomic-force microscopy (AFM) in an actively focused, controlled illumination environment to image particles from millimeters to nanometers in size. Careful selection of substrates allows controlled experiments in adhesion, abrasion, hardness, aggregation, magnetic and other properties. Special tools allow primitive manipulation (brushing and scraping) of samples. Soil particle properties including size, shape, color, hardness, adhesive potential (electrostatic and magnetic), will be determined using an array of sample receptacles and collection substrates. The simple, rugged atomic-force microscope will image in the submicron size range and has the capability of performing a particle-by-particle analysis of the dust and soil. On Earth, the earliest forms of life are preserved as microfossils. The atomic-force microscope will have the required resolution to image down to the scale of terrestrial microfossils and beyond. Mounted on the end of the robot arm, MECA's electrometer actually consists of four types of sensors: an electric field meter, several triboelectricity monitors, an ion gauge, and a thermometer. Tempered only by ultraviolet-light-induced ions and a low-voltage breakdown threshold, the dry, cold, dusty martian environment presents an imposing electrostatic hazard to both robots and humans. The field meter will measure the ambient field on nearby objects while the triboelectric sensors, using identical circuitry, will measure the charge accumulated on test substances as they are dragged through the soil by the arm. The ion chamber, open to the environment, will sense both charged dust and free ions in the air. Over and above the potential threat to electronics, the electrostatic environment holds one of the keys to transport of dust and, consequently, Martian meteorology. Viewed with the robot arm camera, the abrasion and adhesion plates are strategically placed to allow direct observation of the interaction between materials and soils on a macroscopic scale. Materials of graded hardness are placed directly under the robot arm scoop to sense wear and soil hardness. A second array, placed on the lander deck, is deployed after the dust plume of landing has settled. It can be manipulated in a primitive fashion by the arm, first having dirt deposited on it from the scoop and subsequently shaken clean. A third array will passively collect dust from the atmosphere. In addition to objectives related to human exploration, the MECA data set will be rich in information relevant to basic geology, paleoclimate, and exobiology issues. To understand both contemporaneous and ancient processes on Mars, the mineralogy, petrology, and reactivity of Martian surface materials should be constrained. The MECA experiment will shed light on these quantities through its combination of chemistry and microscopy. MECA will be capable of measuring the composition of ancient surface water environments, observing microscopic evidence of geological (and biological?) processes, inferring soil and dust transport, comminution and weathering mechanisms, and characterizing soil horizons that might be encountered during excavation.

Hecht, M. H.↗