Search NASA⌕ Search

SEARCH · Search NASA

Results for “HgI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

STOVL Hot Gas Ingestion control technology

A comprehensive wind tunnel test program was conducted to evaluate control of Hot Gas Ingestion (HGI) on a 9.2 percent scale model of the McDonnell Aircraft Company model 279-3C advanced Short Takeoff and Vertical Landing (STOVL) configuration. The test was conducted in the NASA-Lewis Research Center 9 ft by 15 ft Low Speed Wind Tunnel during the summer of 1987. Initial tests defined baseline HGI levels as determined by engine face temperature rise and temperature distortion. Subsequent testing was conducted to evaluate HGI control parametrically using Lift Improvement Devices (LIDs), forward nozzle splay angle, a combination of LIDs and forward nozzle splay angle, and main inlet blocking. The results from this test program demonstrate that HGI can be effectively controlled and that HGI is not a barrier to STOVL aircraft development.

Amuedo, K. C.↗

Dynamic response of induced pressures, suckdown, and temperatures for two tandem jet STOVL configurations

NASA Ames Research Center has been conducting a program to improve the methods for predicting the jet-induced lift loss (suckdown) and hot gas ingestion on jet Short Takeoff and Vertical Landing (STOVL) aircraft during hover near the ground. As part of that program, small-scale hover tests were conducted to expand the current data base and to improve upon the current empirical methods for predicting jet-induced lift loss and hot gas ingestion (HGI) effects. This report is one of three data reports covering data obtained from hover tests conducted at Lockheed Aeronautical Systems, Rye Canyon Facility. It will include dynamic (time dependent) test data for both lift loss and HGI parameters (height, nozzle temperature, nozzle pressure ratio, and inlet location). The flat plate models tested were tandem jet configurations with three planform variations and variable position side-by-side sucking inlets mounted above the planform. Temperature time lags from 8-15 seconds were observed before the model temperatures stabilize. This was larger than the expected 1.5-second lag calculated from literature. Several possible explanations for the flow temperatures to stabilize may include some, or all, of the following: thermocouple lag, radiation to the model surface, and heat loss to the ground board. Further investigations are required to understand the reasons for this temperature lag.

Wardwell, Douglas A.↗

Progress Toward Generation of a Navier-Stokes Database for a Harrier in Ground Effect

The Harrier YAV-8B aircraft is capable of vertical and short-field take-off and landing (V/STOL) by directing its four exhaust nozzles toward the ground, or conventional flight by rotating its nozzles into a horizontal position. The British Royal Air Force and the United States Marine Corps have used this aircraft for more than 30 years to provide a quick reaction time for troop support, and reduce the need for long runways. The success of this powered-lift (PL) vehicle has also prompted the more recent design of the Joint Strike Fighter (JSF). However there are significant safety issues that must be addressed when operating a PL vehicle in close proximity to the ground. Hot Gas Ingestion (HGI) by the inlets can result in a rapid loss of powered lift; and high-speed jet flows along the ground plane can induce low pressures underneath the vehicle, causing a 'suck-down' effect. Under these conditions, departure from controlled flight may occur. Moreover, unsteady ground vortices and jet fountains can affect the aircraft,s controllability and its proximity to ground troops. The viscous, time-dependent flow fields of PL vehicles are difficult to accurately and efficiently predict using Computational Fluid Dynamics (CFD). A number of researchers have used the time-dependent Reynolds-averaged Navier-Stokes (RANS) equations to compute flows for single and multiple jets in a cross-flow. A few have added some geometric complexity to the problem by computing flows for jet-augmented delta wings near a ground plane. Smith et.al. computed for the first time a single RANS solution about a simplified Harrier. This geometry included a fuselage, wing, leading edge root extension (LERX), inlets, and exhaust nozzles. All of these investigations cite two practical problems with computing these flows: 1) the need for improved solution accuracy; and, 2) the need for faster solution methods. We view the need for faster solution methods as key to improving the solution accuracy and making this class of computation more routine. One can hardly refine grids, explore the use of advanced turbulence models, and generate databases when it takes weeks of dedicated computer time for a single solution. Chaderjian, Ahmad, Pandya, and Murman have focused on reducing the time-to-solution for this very difficult and complex problem through process automation and exploitation of parallel computing. They began with the Harrier geometry reported, and added a deflected wing flap and empennage for greater realism. To date more than 80 solutions have been carried out. This paper will describe this process and progress made in reducing the time required to generate a simple longitudinal force and moment database for a Harrier in ground effect. It shows a typical snap-shot from an unsteady streakline animation, where fluid particles are colored by temperature. The ground vortex and a jet-fountain vortex are highlighted. It also shows a similar streakline image, where HGI occurs due to the vehicle in close proximity to the ground. It is show the mean lift coefficient as a function of angle of attack and height. The angle of attack range was 4 deg less than or = alpha less than or = 10 deg with an increment of 1 degree, and the height range was 10 ft less than or = h less than or = 30ft with an increment of 5 feet. This 35 solution database was extended to over 2500 cases using a monotone cubic-spline interpolation procedure. The suck-down effect (reduction of lift near the ground) is highlighted in the figure. The "cushion effect," the conventional reduction of lift as the vehicle moves out of ground effect, is also indicated. All 35 RANS solutions were obtained using 952 Silicon Graphics Origin 2000 and 3000 processors in dedicated mode for one week. Typically, 112 processors were assigned to each case. Some other cases used fewer processors to utilize all available CPUS. The final paper will report on the automation of the solution process, including: grid generation, job monitoring, solution completion criteria, and post processing. Moreover, improvements in parallel efficiency for a dual time-step algorithm for the RANS equations will also be presented. Results will be discussed in detail using unsteady streakline flow visualization to correlate unsteady flow structures with dominant aerodynamic frequencies. The stability derivatives, CL, and CL, will also be presented.

Chaderjian, Neal M.↗

Vapor Growth of Alloy-Type Semiconductor Crystals

The present effort is part of a continuing research program directed towards the investigation of basic vapor transport phenomena and of crystal growth properties of electronic materials. The primary purpose of ground-based studies is the development and definition of optimum experimental parameters for flight experiments. The ground-based effort includes the investigation of gravity-driven convection effects on mass transport rates and on crystal morphology for different orientations of the density gradient with respect to the gravity vector, and as a function of pressure and of temperature. In addition to the experimental tasks, theoretical efforts involve the quantitative thermodynamic analysis of the systems under investigation, the computation of fluid dynamic parameters, and the consideration of other possible effects on fluid flow under vertical, stabilizing and microgravity conditions. The specific experiments to be performed in a microgravity environment include the investigation of vapor transport and crystal growth phenomena of the GeSe-Xenon system and of the mass flux and growth of bulk and layer-type crystals of Hg sub (1-x) Cd sub x Te using HgI as a transport agent.

Wiedemeier, H.↗

Hot gas ingestion: From model results to full scale engine testing

An overview is presented of a joint NASA Lewis McDonnell Aircraft Co. Hot Gas Ingestion (HGI) test program in NASA Lewis' 9 x 15 foot Low Speed Wind Tunnel (LSWT). Advanced short takeoff vertical landing (ASTOVL) aircraft capable of operating from remote sites, damaged runways, aircraft carriers and small air-capable ships are being pursued for deployment around the turn of the century. To achieve this goal, it is important that technologies critical to this unique class of aircraft be developed. One of the ASTOVL concepts, the vectored thrust, has as its critical technology item, the potential of hot gas ingestion (which occurs during vertical flight operation while in ground effect) as a key development issue. Recognizing this need, NASA Lewis Powered Lift Section and McAir have defined a cooperative program for testing in the Lewis 9 x 15 foot LSWT. This program is described in detail.

Johns, Albert L.↗

Flow visualization studies of VTOL aircraft models during Hover in ground effect

A flow visualization study of several configurations of a jet-powered vertical takeoff and landing (VTOL) aircraft model during hover in ground effect was conducted. A surface oil flow technique was used to observe the flow patterns on the lower surfaces of the model. There were significant configuration effects. Wing height with respect to fuselage, the presence of an engine inlet duct beside the fuselage, and nozzle pressure ratio are seen to have strong effects on the surface flow angles on the lower surface of the wing. This test was part of a program to improve the methods for predicting the hot gas ingestion (HGI) for jet-powered vertical/short takeoff and landing (V/STOL) aircraft. The tests were performed at the Jet Calibration and Hover Test (JCAHT) Facility at Ames Research Center.

Mourtos, Nikos J.↗

Parametric Time-Dependent Navier-Stokes Computations for a YAV-8B Harrier in Ground Effect

The Harrier Jump Jet has the distinction of being the only powered-lift aircraft in the free world to achieve operational status and to have flown in combat. This V/STOL aircraft can take-off and land vertically or utilize very short runways by directing its four exhaust nozzles towards the ground. Transition to forward flight is achieved by rotating these nozzles into a horizontal position. Powered-lift vehicles have certain advantages over conventional strike fighters. Their V/STOL capabilities allow for safer carrier operations, smaller carrier size, and quick reaction time for troop support. Moreover, they are not dependent on vulnerable land-based runways. The AV-8A Harrier first entered service in the British Royal Air Force (RAF) during 1969, and the U.S. Marine Corps (USMC) in 1971. The AV-8B was a redesign to achieve improved payload capacity, range, and accuracy. This modified design first entered service with the USMC and RAF in 1985. The success and unique capabilities of the Harrier has prompted the design of a powered-lift version of the Joint Strike Fighter (JSF). The flowfield for the Harrier near the ground during low-speed or hover flight operations is very complex and time-dependent. A sketch of this flowfield is shown. Warm air from the fan is exhausted from the front nozzles, while a hot air/fuel mixture from the engine is exhausted from the rear nozzles. These jets strike the ground and move out radially forming a ground jet-flow. The ambient freestream, due to low-speed forward flight or - headwind during hover, opposes the jet-flow. This interaction causes the flow to separate and form a ground vortex. The multiple jets also interact with each other near the ground and form an upwash or jet fountain, which strikes the underside of the fuselage. If the aircraft is sufficiently close to the ground, the inlet can ingest ground debris and hot gases from the fountain and ground vortex. This Hot Gas Ingestion (HGI) can cause a sudden loss of thrust (powered lift), and the vehicle may crash. The high-speed jet flow along the ground can also entrain the ambient flow, resulting in a low pressure region underneath the vehicle. The accompanied loss of lift is referred to as the suckdown effect. The ground vortex may also be highly unsteady, dramatically changing its size and position with time at low frequencies, e.g., 1 Hz.

Chaderjian, Neal M.↗

Evaluation of the Minifilament-Eruption Scenario for Solar Coronal Jets in Polar Coronal Holes

Solar coronal jets are suspected to result from magnetic reconnection low in the Sun's atmosphere. Sterling et al. (2015) looked as 20 jets in polar coronal holes, using X-ray images from the Hinode/X-Ray Telescope (XRT) and EUV images from the Solar Dynamics Observatory (SDO) Atmospheric Imaging Assembly (AIA). They suggested that each jet was driven by the eruption of twisted closed magnetic field carrying a small-scale filament, which they call a 'minifilament', and that the jet was produced by reconnection of the erupting field with surrounding open field. In this study, we carry out a more extensive examination of polar coronal jets. From 180 hours of XRT polar coronal hole observations spread over two years (2014-2016), we identified 130 clearly-identifiable X-ray jet events and thus determined an event rate of over 17 jets per day per in the Hinode/XRT field of view. From the broader set, we selected 25 of the largest and brightest events for further study in AIA 171, 193, 211, and 304 Angstrom images. We find that at least the majority of the jets follow the minifilament-eruption scenario, although for some cases the evolution of the minifilament in the onset of its eruption is more complex than presented in the simplified schematic of Sterling et al. (2015). For all cases in which we could make a clear determination, the spire of the X-ray jet drifted laterally away from the jet-base-edge bright point; this spire drift away from the bright point is consistent with expectations of the minifilament-eruption scenario for coronal-jet production. This work was supported with funding from the NASA/MSFC Hinode Project Office, and from the NASA HGI program.

holes↗

Magnetic Flux Cancelation as the Buildup and Trigger Mechanism for CME-Producing Eruptions in Two Small Active Regions

We follow two small, magnetically isolated CME (Coronal Mass Ejection)-producing solar active regions (ARs) from the time of their emergence until several days later, when their core regions erupt to produce the CMEs. In both cases, magnetograms show: (a) following an initial period where the poles of the emerging regions separate from each other, the poles then reverse direction and start to retract inward; (b) during the retraction period, flux cancelation occurs along the main neutral line of the regions, (c) this cancelation builds the sheared core field/flux rope that eventually erupts to make the CME. In the two cases, respectively 30 percent and 50 percent of the maximum flux of the region cancels prior to the eruption. Recent studies indicate that solar coronal jets frequently result from small-scale filaments eruptions (Sterling et al. 2015), with those “minifilament” eruptions also being built up and triggered by cancelation of magnetic flux (Panesar et al. 2016). Together, the small-AR eruptions here and the coronal jet results suggest that isolated bipolar regions tend to erupt when some threshold fraction, perhaps in the range of 50 percent, of the region’s maximum flux has canceled. Our observed erupting filaments/flux ropes form at sites of flux cancelation, in agreement with previous observations. Thus, the recent finding that minifilaments that erupt to form jets also form via flux cancelation is further evidence that minifilaments are small-scale versions of the long-studied full-sized filaments. (Details are in Sterling et al. 2018, ApJ, 864, 68.) Supported by NASA's Heliophysics Guest Investigators (HGI) Program and the MSFC (Marshall Space Flight Center)/Hinode project.

Sterling, Alphonse C.↗

Hinode and SDO Observations of a Two-Sided-Loop Coronal Jet: Toward a General Picture for Jets

Most of the commonly discussed solar coronal jets are of the type consisting of a single spire extending approximately vertically from near the solar surface into the corona. Recent research of a substantial number of events shows that eruption of a miniature filament (minifilament) drives at least many such single-spire jets, and concurrently generates a miniflare at the eruption site. A different type of coronal jet, identified in X-ray images during the Yohkoh era, are two-sided-loop jets, which extend from a central excitation location in opposite directions, along two opposite low-lying coronal loops that are more-or-less horizontal to the surface. We observe such a two-sided-loop jet from the edge of active region (AR) 12473, using data from Hinode XRT and EIS, and SDO AIA and HMI. Similar to single-spire jets, this two-sided-loop jet results from eruption of a minifilament, which accelerates to over 140 km/s before abruptly stopping upon striking overlying nearly horizontal magnetic field at ∼30,000 km altitude and producing the two-sided-loop jet via interchange reconnection. Analysis of EIS raster scans show that a hot brightening, consistent with a small flare, develops in the aftermath of the eruption, and that Doppler motions (∼40 km/s) occur near the jet-formation region. As with many single-spire jets, the trigger of the eruption here is apparently magnetic flux cancelation, which occurs at a rate of ∼4×10^18 Mx/hr, comparable to the rate observed in some single-spire AR jets. This example of a two-sided jet, along with numerous examples of single-spire jets, supports that essentially all coronal jets result from eruptions of minifilaments, and frequently the eruption of the minifilament is triggered by magnetic flux cancelation. This work was supported by the NASA HGI program, and the MSFC Hinode project. (Details are in Sterling et al. 2019, ApJ, 871, 220.)

Sterling, Alphonse C.↗

A Hinode-IRIS HOP for Searching for Possible Solar Jet Sources for Switchbacks Observed in the Near-Sun Solar Wind by the Parker Solar Probe (PSP)

The Parker Solar Probe (PSP) detects “switchback” magnetic structures in the near-Sun solar wind. A candidate for the source of these is solar coronal jets. Recent studies show that coronal jets are frequently made by eruptions of small-filament-carrying flux ropes, or mini filament flux-rope eruptions, that can inject a magnetic twist wave onto high-reaching ambient magnetic field(Sterling et al. 2015; Moore et al 2015).That is, many coronal jets evidently result from the eruption of a small-scale flux rope of twisted field that holds a mini filament of chromospheric-temperature plasma. The erupting flux rope reconnects with ambient far-reaching field, ejecting both reconnection-heated plasma and cool filament plasma (forming the multi-temperature jet spire), and transferring its twist onto the far-reaching field via a mechanism proposed by Shibata & Uchida(1986).If the far-reaching field opens into the heliosphere, it is plausible that the twist propagates out into the solar wind, possibly appearing as a switchback in the magnetic field in the solar wind (Sterling & Moore 2020).As part of the "Connecting Heliophysics Observatories and Models with PSP" (CHOMP)investigation led by Pete Riley and funded by NASA’s Heliophysics System Observatory Connect (HSOC) Program, we are currently We are currently running a joint Hinode-IRIS HOP, HOP 410, for coordinated observations of the Sun during times of PSP perihelia. An output from this study is a series of soft X-ray movies from Hinode/XRT. If PSP sees a strong switchback during any of its front-side or partly-front-side perihelia, we will examine the corresponding XRT movies to see whether exceptional jet activity occurred at the expected time and location of the potential source of the switchback on the Sun. This work is supported by the NASA HSOC and HGI programs, and by the MSFC Hinode project.

Alphonse C Sterling↗

Another Look at Erupting Minifilaments at the Base of Solar X-Ray Polar Coronal “Standard” and “Blowout” Jets

We examine 21 solar polar coronal jets that we identify in soft X-ray images obtained from the Hinode/X-ray telescope (XRT). We identify 11 of these jets as blowout jets and four as standard jets (with six uncertain), based on their X-ray-spire widths being respectively wide or narrow (compared to the jet’s base) in the XRT images. From corresponding Extreme Ultraviolet (EUV) images from the Solar Dynamics Observatory’s (SDO) Atmospheric Imaging Assembly (AIA), essentially all (at least 20 of 21) of the jets are made by minifilament eruptions,consistent with other recent studies. Here, we examine the detailed nature of the erupting minifilaments (EMFs) in the jet bases. Wide-spire (“blowout”) jets often have ejective EMFs, but sometimes they instead have an EMF that is mostly confined to the jet’s base rather than ejected. We also demonstrate that narrow-spire (“standard”) jets can have either a confined EMF, or a partially confined EMF where some of the cool minifilament leaks into the jet’s spire. Regarding EMF visibility: we find that in some cases the minifilament is apparent in as few as one of the four EUV channels we examined, being essentially invisible in the other channels; thus it is necessary to examine images from multiple EUV channels before concluding that a jet does not have an EMF at its base. The size of the EMFs, measured projected against the sky and early in their eruption, is 14′′ ± 7′′, which is within a factor of two of other measured sizes of coronal-jet EMFs. A full report on these results will be published in the Astrophysical Journal. This work was supported by NASA's HGI, HSR, and HSOC programs, and by the NASA/MSFC Hinode Project.

Alphonse C Sterling↗

Another Look at Erupting Minifilaments at the Base of Solar X-Ray Polar Coronal “Standard” and “Blowout” Jets

We examine 21 solar polar coronal jets that we identify in soft X-ray images obtained fromthe Hinode/X-ray telescope (XRT). We identify 11 of these jets as blowout jets and four asstandard jets (with six uncertain), based on their X-ray-spire widths being respectively wide or narrow (compared to the jet’s base) in the XRT images. From corresponding Extreme Ultraviolet (EUV) images from the Solar Dynamics Observatory’s (SDO) Atmospheric Imaging Assembly (AIA), essentially all (at least 20 of 21) of the jets are made by minifilament eruptions, consistent with other recent studies. Here, we examine the detailed nature of the erupting minifilaments (EMFs) in the jet bases. Wide-spire (“blowout”) jets often have ejective EMFs, but sometimes they instead have an EMF that is mostly confined to the jet’s base rather than ejected. We also demonstrate that narrow-spire (“standard”) jets can have either a confined EMF, or a partially confined EMF where some of the cool minifilament leaks into the jet’s spire. Regarding EMF visibility: we find that in some cases the minifilament is apparent in as few as one of the four EUV channels we examined, being essentially invisible in the other channels; thus it is necessary to examine images from multiple EUV channels before concluding that a jet does not have an EMF at its base. The size of the EMFs, measured projected against the sky and early in their eruption, is 14′′ ± 7′′, which is within a factor of two of other measured sizes of coronal-jet EMFs. A full report on these results are available in Sterling et al. (2022, ApJ, 927, 127).This work was supported by NASA’s HGI and HSR programs, and by the MSFC HinodeProject.

Alphonse C Sterling↗

Expansion of Existing Research and Analysis Programs

Small-grants programs play a vital role in Heliophysics research. They are a modest investment with a huge scientific payoff. Frequently, it is individuals and small research groups funded by small grants that make the high-innovation breakthroughs that have such a transformative impact on a field. Small grants also give most early-career researchers their first experience as principal investigator – experience they need to eventually become leaders in their field. We therefore recommend that existing NASA programs like Heliophysics Supporting Research (HSR), Heliophysics Guest Investigator (HGI), and Heliophysics Technology and Instrument Development for Science (HTIDeS) be greatly expanded. We also recommend that funding opportunities be created for mid-size grants, $500-1000K/yr, either as part of existing programs or with new programs dedicated to this size.

James A. Klimchuk↗