Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Density Interconnect (HDI) technology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

5 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Power Actuation and Switching Module Development

The Deep Space Avionics (DSA) Project is developing a Power Actuation and Switching Module (PASM). This component enables a modular and scalable design approach for power switching applications, which can result in a wide variety of power switching architectures using this simple building block. The PASM is designed to provide most of the necessary power switching functions of spacecraft for various Deep Space missions including future missions to Mars, comets, Jupiter and its moons. It is fabricated using an A SIC process that is tolerant of high radiation. The development includes two application specific integrated circuits (ASICs) and support circuitry all packaged using High Density Interconnect (HDI) technology. It can be operated in series or parallel with other PASMs, It can be used as a high-side or low-side switch and it can drive thruster valves, pyrotechnic devices such as NASA standard initiators, bus shunt resistors, and regular spacecraft component loads. Each PASM contains two independent switches with internal current limiting and over-current trip-off functions to protect the power subsystem from load faults. During turnon and turnoff each switch can limit the rate of current change (di/dt) to a value determined by the user. Threeway majority-voted On/Off commandability and full switch status telemetry (both analog and digital) are built into the module. This paper describes the development process used to design, model, fabricate, and test these compact and versatile power switches. Preliminary test results from prototype HDI PASM hardware are also discussed.

Power Actuation and Switching Module (PASM)↗
NASA NTRS2006

Power Actuation and Switching Module Test Results

The X2000 Power System Electronics (PSE) is a Jet Propulsion Laboratory (JPL) task to develop a new generation of power system building blocks for use on future deep-space missions. The effort includes the development of electronic components and modules that can be used as building blocks in the design of generic spacecraft power systems. All X2000 avionics components and modules are designed for use in centralized or distributed spacecraft architectures. The Power Actuation and Switching Module (PASM) has been developed under the X2000 program. This component enables a modular and scalable design approach for power switching applications, which can result in a wide variety of power switching architectures using this simple building block. The PASM is designed to provide most of the necessary power switching functions of spacecraft for various Deep Space missions including future missions to Mars, comets, Jupiter and its moons. It is fabricated using an ASIC process that is tolerant of high radiation. The development included two application specific integrated circuits (ASICs) and support circuitry all packaged using High Density Interconnect (HDI) technology. It can be operated in series or parallel with other PASMs. It can be used as a high-side or low-side switch and it can drive thruster valves, pyrotechnic devices such as NASA standard initiators, bus shunt resistors, and regular spacecraft component loads. Each PASM contains two independent switches with internal current limiting and over-current trip-off functions to protect the power subsystem from load faults. During turnon and turnoff each switch can limit the rate of current change (di/dt) to a value determined by the user. Three-way majority-voted On/Off commandability and full switch status telemetry (both analog and digital) are built into the module. This paper is a follow up to the one presented at he IECEC 2004 conference that will include the lessons learned and test results from the development.

X2000↗
NASA NTRS1993

Advanced microfabrication technologies for microspacecraft

Advanced microfabrication technologies offer the prospect of reducing the weight and size of spacecraft through the use of lighter and stronger materials in conjunction with new mechanical/structural design concepts and design optimization methods. At the same time, electronic components have been scaled down while increasing functional utility. A two-fold benefit is derived for space applications through the use of less expensive components and the lower launch costs associated with lighter components. GE-CRD is actively pursuing research in these key technologies for a wide range of applications including satellites. These key technologies will be reviewed and an update on GE progress will be given. The need to reduce weight and lower cost, while maintaining product quality and reliability are primary drivers in the design of satellites, in general, and microsatellites in particular. For the structural subsystem, these requirements pose a complex design problem unless new mechanical design concepts and computer-aided design optimization methods are employed. Several new concepts, such as battery packs doubling as panel reinforcements and fuel tanks as integral structural members, need to utilized. In addition, new viscoelastic material damping concepts for spacecraft components provide for lighter weight/lower cost designs, while satisfying the structural dynamics requirements. High density interconnect (HDI) technology permits the use of bare IC's on a ceramic substrate with 90 percent active area utilization. A copper/polyimide multilayer structure is the backbone of the technology, which has demonstrated a size/weight reduction of greater than 10x compared to printed circuit board with performance up to the GHz level. HDI modules have exceptional mechanical robustness as evidenced by survival of 180 kg rapid acceleration tests. Microelectromechanical systems (MEMS) are redefining sensors and actuators by miniaturization through micromachining techniques. Sharing many fabrication steps with HDI, we have developed a new technique for surface micromachining of copper/polyimide structures using computer-aided laser patterning.

Ghezzo, M.↗
NASA NTRS2010

Disruptive Technologies in Workmanship: pH-neutral Flux, CDM ESD Events, HDI PCBs

This slide presentation describes what it calls "disruptive technologies", i.e., "Low-end disruption" occurs when the rate at which products improve exceeds the rate at which customers can adopt the new performance. Therefore, at some point the performance of the product overshoots the needs of certain customer segments. At this point, a disruptive technology may enter the market and provide a product which has lower performance than the incumbent but which exceeds the requirements of certain segments, thereby gaining a foothold in the market. This concept is viewed in impacting incumbent technologies Rosin Flux, with a pH-neutral water soluble Flux; electrostatic discharge models being disrupted by the charge device model (CDM) concept; and High Density Interconnect Printed Circuit Boards (HDI PCB).

Plante, Jeannette F.↗
NASA NTRS2014

Reliability of CGA/LGA/HDI Package Board/Assembly (Final Report)

Package manufacturers are now offering commercial-off-the-shelf column grid array (COTS CGA) packaging technologies in high-reliability versions. Understanding the process and quality assurance (QA) indicators for reliability are important for low-risk insertion of these advanced electronics packages. The previous reports, released in January of 2012 and January of 2013, presented package test data, assembly information, and reliability evaluation by thermal cycling for CGA packages with 1752, 1517, 1509, and 1272 inputs/outputs (I/Os) and 1-mm pitch. It presented the thermal cycling (-55C either 100C or 125C) test results for up to 200 cycles. This report presents up to 500 thermal cycles with quality assurance and failure analysis evaluation represented by optical photomicrographs, 2D real time X-ray images, dye-and-pry photomicrographs, and optical/scanning electron Microscopy (SEM) cross-sectional images. The report also presents assembly challenge using reflowing by either vapor phase or rework station of CGA and land grid array (LGA) versions of three high I/O packages both ceramic and plastic configuration. A new test vehicle was designed having high density interconnect (HDI) printed circuit board (PCB) with microvia-in-pad to accommodate both LGA packages as well as a large number of fine pitch ball grid arrays (BGAs). The LGAs either were assembled onto HDI PCB as an LGA or were solder paste print and reflow first to form solder dome on pads before assembly. Both plastic BGAs with 1156 I/O and ceramic LGAs were assembled. It also presented the X-ray inspection results as well as failures due to 200 thermal cycles. Lessons learned on assembly of ceramic LGAs are also presented.

Ghaffaroam. Reza↗