SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
High-energy-density primary battery achieves energy densities of up to 130 watt hrs./lb. The electrochemical couple consists of a lithium anode, a copper-fluoride cathode, and uses methyl formate/lithium hexafluoroarsenate for the electrolyte. Once achieved, battery life is approximately 30 hours.
Sodium-sulfur (Na-S) batteries hold promise as high-energy-density batteries for long-duration energy storage due to their high open circuit voltage and Earth-abundant active materials. However, low utilization of the sulfur active material limits the achievable specific capacity, especially when a liquid polysulfide catholyte is utilized. High-surface-area carbon materials demonstrate promise to increase sulfur utilization in a Na-S battery. To make the carbon host material applicable for a flow battery application, a binder is required to bind the carbon materials together and to a porous substrate. Here, we utilize a composite carbon paper electrode coated by polymer,carbon nanofibers (CNFs) and carbon black (CB). By varying the mass ratios of CNF to CB, we found that a 70/20/10 mass ratio of CNF/CB/binder provided the highest capacity (260 mAh g −1 compared to the baseline of 156 mAh g −1 ) and stable battery performance over 100 cycles. Analysis of the composite electrode and full cells reveals that the amount of CB in the composite electrode influences binder distribution, cell resistance, and full cell performance.
In the absence of viable high-energy-density battery alternatives, lithium-ion (Li-ion) batteries remain essential for enabling electric vertical take-off and landing (eVTOL) platforms in advanced air mobility. Unlike Li-ion batteries used in electric vehicles and portable electronics, eVTOL battery systems operate under distinct high-power demands, which necessitate an independent assessment of material degradation mechanisms. This study presents a case analysis of graphite anode evolution under high-power cycling conditions. The findings reveal lithium entrapment within graphite particles, potentially resulting from incomplete Li-ion de-intercalation during a high-rate discharge event that is characteristic of eVTOL take-off and landing. This phenomenon leads to a progressive reduction in graphite-specific capacity and, over time, promotes lithium metal plating on the anode. Notably, the Li-metal plating observed in this study differs from that associated with fast-charging conditions, as it is primarily governed by concentration polarization-induced overpotential in the latter case. In conclusion, these findings highlight the inherent challenges of utilizing graphite in high-power Li-ion battery applications and elucidate the unique degradation mechanisms that arise due to the sluggish reaction kinetics of Li-ion intercalation and de-intercalation within graphite.
Solid-state electrolytes, such as lithium lanthanum zirconium oxide (LLZO), show promise as technologies for next-generation high-energy-density batteries, but commercial development has been hindered by a lack of scalable processing methods. Current fabrication methods are costly or require long annealing steps to create dense films. We report an atmospheric pressure blown-arc nitrogen plasma jet process to rapidly form sub-micrometer-thick, dense amorphous LLZO (a-LLZO) films from sol-gel precursors. Films are processed in less than 2 min, an order of magnitude faster than what has previously been reported. We demonstrate 500-nm-thick a-LLZO films processed at 350°C with an ionic conductivity of 2 × 10 −6 S/cm at 30°C and 2 × 10 −3 S/cm at 100°C and a conductance of 19 S at 100°C, the highest conductance of any LLZO phase to date. Here, the films exhibit outstanding smooth surface morphology with low defectivity, advancing atmospheric plasma processing as a scalable processing method for solid-state electrolytes.
The development of high-energy-density Na-ion batteries places significant demands on single-crystal layered oxide cathodes, especially for further high-voltage, solid-state battery scenarios. In the O3-type structure, due to the original sluggish Na ion diffusion kinetics (approximately 1 order of magnitude lower than that of Li-ion), and further hindrance against diffusion kinetics caused by single-crystal architecture, these inherent defects lead to the decline in the electrochemical performance. Herein, we demonstrated that the single crystallization of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 cathode (d 50 = 5.04 μm) aggravates surface-to-bulk phase inhomogeneity distribution, which is attributed to the uneven Na ions extraction. Moreover, the Na-depletion of the surface/shell region not only aggravates Na ion diffusion resistance but also leads to a higher valence state of transition-metal elements (e.g., Ni/Fe) near the surface of the single-crystal particle, which further compromises the cathode-electrolyte interface stability. Furthermore, not limited to revealing the challenges, tuning the particle size and moderating quasi-single-crystal strategies have been proven to effectively mitigate the negative uneven distributions of Na ions, phases, and valence/oxidative states, resulting in efficient modification for single crystallization of Na-layered oxide cathodes.
Sodium-sulfur batteries promise high-energy-density and sustainable electrochemical energy storage but suffer from uncontrolled polysulfides dissolution and high sodium reactivity. These challenges fundamentally originate from poor electrolyte-electrode compatibility. Current electrolyte research inadequately addresses the trade-off between minimal polysulfides solvation and stabilizing sodium interfaces. Here, we present a locally-confined polysulfide-reactive electrolyte strategy that mediates the polysulfide dissolution dynamics and sodium stability by leveraging an electrophilic solvating species with a localized high-concentration electrolyte. This design enables shuttle-free cell operation by synergistically restricting the global solvating power of the electrolyte through intermolecular interactions and locally scavenging sparingly dissolved polysulfides via electrolyte electrophilicity. The precisely confined surface reaction facilitates a protective cathode-electrolyte interface, realizing a quasi-solid-state sulfur conversion in our liquid ether-based electrolyte, which crucially avoids crossover-induced catastrophic sodium-metal degradation. The proposed electrolyte demonstrates long-term cycling of high-mass-loading sulfur cathodes (> 3 mg S cm −2 with commercial carbon host and 70 wt% sulfur content), which afford 710 mA h g −1 over 400 cycles in coin cells and steady pouch cell operation over 180 cycles. Furthermore, this work establishes a scalable electrolyte design protocol that regulates the reaction chemistry of highly reactive electrodes, offering a pathway toward sustainable renewable energy storage.
The pervasive use of Ni-rich cathode active materials, e.g., LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811), for high-energy-density Li-ion batteries (LIBs) has been hindered by rapid battery capacity decay when cycled with high charge cutoff voltages due to electrolyte decomposition in the conventional carbonate solvent-based electrolytes, oxidative parasitic side reactions at the electrolyte/cathode interface, and irreversible phase changes in the cathode active materials leading to dissolution of transition metals into the electrolytes. Various functional electrolyte solvents have been studied to tackle the above technical challenges, yet the roles of individual solvents in the performance of LIBs remain poorly understood. Here, in this study, we systematically investigate electrochemical performance mechanisms of fluorinated and organosilicon single solvents and cosolvents, for the first time, in high-voltage Li/NMC811 batteries, using electrochemical and analytical characterizations and density functional theory modeling. We observe that some unique combinations of the functional solvents can lead to exceptionally stable high-voltage cycle performance in the Ni-rich cathode-based LIBs. Our mechanistic study reveals that the synergistic effect of solvents plays a vital role in enabling electrochemical stability at both the Ni-rich cathode and the Li metal anode. Understanding the electrochemical performance mechanisms of functional solvents can greatly help in designing and formulating advanced electrolytes that enable the development of high-voltage, high-energy-density, long-cycle-life lithium batteries.
The advancement of high-energy-density lithium-metal batteries (LMBs) is hindered by the chemical instability of both lithium-metal anode and high-nickel layered oxide cathodes. While cathode-to-anode crossover is well-documented, the reverse process of anode-to-cathode crossover remains underexplored. Here, we systematically investigate such crossovers and the degradation pathway in pouch cells with a localized high-concentration electrolyte, comparing NMC622, NMC811, and NMC90 cathodes paired with lithium-metal and graphite anodes. Despite delivering higher initial capacities, LMBs exhibit faster capacity fade under long-term cycling at 45 °C. To isolate cathode-side degradation, galvanostatic electrochemical impedance spectroscopy (GEIS) measurements of cycled cathodes paired with delithiated lithium iron phosphate (LFP) counter electrodes reveal significantly higher charge-transfer resistance in cathodes cycled with lithium-metal. Surface characterization via X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) reveals greater electrolyte decomposition on cathodes cycled with lithium metal, leading to thicker, more organic-rich cathode–electrolyte interphases (CEIs), consistent with the elevated charge-transfer resistance observed in GEIS measurements. Notably, NMC90 shows the most pronounced CEI thickening, linking higher cathode surface reactivity to greater susceptibility to anode-to-cathode crossover. This work presents compelling evidence of crosstalk degradation originating from lithium-metal anodes and underscores the importance of cross-interface stability for the design of durable LMBs.
Li-rich layered oxides exhibit promising potential applications in high-energy-density solid-state lithium metal batteries. Nevertheless, the strong oxidative oxygen species generate at high voltage, which poses great challenges to positive electrode-side interface stability. Herein, a robust in-situ polymerization gel polymer electrolyte with bifunctional additives is designed for interface modification. These additives, include lithium difluoro(oxalate) borate and LiPO 2 F 2 , regulate the Li + chemical environment in gel polymer electrolyte to enhance crosslink density without residual oligomer, which reduce gas generation and suppress contact loss, thus avoiding interfacial impedance divergence. Concurrently, the designed gel polymer electrolyte enables a wide electrochemical stability window (up to 4.7 V) and a high Li + transference number (0.82). Additionally, the additives induced F- and B-rich inorganic cathode-electrolyte interphase inhibits side reactions and oxygen/transition metal loss effectively, stabilizing the chemical interface. The as-constructed Li-rich layered oxides-based ceramic solid-state lithium metal batteries with gel polymer electrolyte interface modification exert a high discharge capacity of 276.5 mAh g -1 at 30 °C without external pressure, delivering a retention of 81.7% after 100 cycles at 25 mA g -1 during 2.0-4.7 V. This work provides a guideline for developing high-voltage solid-state lithium metal batteries via interfacial design.
Lithium-carbon dioxide (Li-CO2) batteries hold great promise for high-energy-density storage applications. However, advancing this technology as a sustainable alternative to Li-ion systems requires a deeper understanding of the underlying reaction mechanisms, which remain elusive. A key challenge stems from the added complexity introduced by the presence of oxygen (O2) in CO2 environment. In this study, we employed a stable Cu3(VBi)0.5Se4 mid-entropy catalyst and conducted a comprehensive investigation to uncover the underlying reaction mechanisms in Li-CO2 batteries under varying CO2/O2 ratios. Under pure CO2 conditions, the battery exhibits excellent rechargeability, sustaining up to 1200 cycles. However, at high current densities, the discharge potential drops significantly (below 2.0 V), primarily due to sluggish reaction kinetics caused by solid carbon formation. Interestingly, introducing O2 mitigates this limitation, leading to a 58% increase of the discharge potential (from 1.7 V to 2.7 V) at the high current density of 0.8 mA/cm2, signifying a substantial boost in energy output. Our results reveal that the reactions follow distinct pathways, shifting from surface- to solution-based mechanism, and may even exhibit coexistence of both mechanisms, depending on the CO2/O2 ratio. These findings offer new insights for designing high-performance and sustainable Li-gas batteries utilizing CO2 and O2 mixtures.
This study evaluates novel electrolytes tailored for Si-containing anodes to promote calendar-life. Drawing inspiration from advancements in electrolytes for Li-metal cells, the work investigates correlations between predicted electrolyte properties and measured electrochemical performance using several machine-learning models. By leveraging machine learning and advanced modeling techniques, this study aims to establish predictive frameworks that accelerate calendar-aging experiments and inform rational electrolyte design for Si-containing cells. In the present study, fifteen different electrolytes are evaluated in a Si-containing cell using an accelerated calendar-life protocol. For each electrolyte considered, 87 properties (features) from the Advanced Electrolyte Model were produced to identify key property/performance relationships. In this study, the best performing electrolytes were generally those formulations that included non-coordinating fluoroether solvents, and the most predictive features for long-term calendar-life were features related to salt concentration and electrolyte viscosity as well as early capacity, ionic conductivity, and Coulombic efficiency measurements. The framework developed in this study correlating electrolyte properties to measured electrochemical performance is expected to accelerate electrolyte design for Si-containing anodes and ultimately enable high-energy-density, long-life Li-ion batteries.
Anionic oxygen redox chemistry in Li-rich Mn-based layer oxide cathodes represents a transformative approach for boosting the energy density of next-generation lithium-ion batteries. However, conventional oxygen redox reactions often induce oxygen dimerization at high voltages, leading to irreversible lattice oxygen loss and a rapid voltage fade. Herein, we achieve highly reversible oxygen redox chemistry through a new quasi-ordered structural design that incorporates both intra- and interlayer cation disorder configurations. This unique structure significantly enhances lattice oxygen stability, effectively stabilizes oxidized oxygen, and inhibits the formation of peroxo- or superoxol-like species, thereby enabling anionic redox reactions to proceed reversibly even at deep delithiation states. The quasi-ordered design mitigates irreversible phase transitions and preserves the structural integrity throughout extended cycling. Consequently, the proposed cathode demonstrates exceptional cyclability with negligible capacity and voltage fade, retaining 99% capacity and 98% average voltage after long-term cycling. Finally this work provides fresh insights into addressing issues related to lattice oxygen instabilities and reforming strategies for developing long-life, high-energy-density anionic redox cathode materials for advanced batteries.
Gel polymers are regarded as a promising candidate electrolyte for lithium-metal quasi-solid-state batteries, primarily due to their high ionic conductivity and solid-liquid synergistic properties. However, challenges such as interfacial side reactions, limitations in Li + transport caused by interfacial issues, and leaching of transition metals from the cathode have yet to be effectively solved. Herein, a novel gel electrolyte modulation strategy based on electrostatic filler assembly is proposed to address the issues of ineffective capacity utilization and inadequate cycling stability of high-energy-density cathode materials in solid-state lithium-ion batteries. It constructs a 3D interpenetrating charge-bridge network that effectively tackles the phase-separation challenge between fillers and electrolytes at the molecular level. Meanwhile, the molecular interlocking structure effectively inhibits the electrolyte erosion. More critically, it optimizes and stabilizes the cathode-electrolyte interface film, which facilitates the conduction of Li + -ions through a size-sieving mechanism. Consequently, this strategy enables effective adaptation across diverse high-energy-density cathode materials with satisfactory capacity performance (170.4 mAh g −1 at 4.5 V/1 C for LiNi 0.6 Co 0.2 Mn 0.2 O 2 and 194.0 mAh g −1 at 4.3 V/1 C for LiNi 0.9 Co 0.08 Mn 0.02 O 2 ). In conclusion, this investigation offers a straightforward and effective reference for addressing the critical challenges of ionic transport and interface stabilization in the design of gel electrolytes.
Nonaqueous magnesium redox flow batteries (Mg RFBs) are attractive for low-cost, high-energy-density and long-cycle-life stationary energy storage applications. However, state-of-the-art cathode redox-active molecules suffer from low solubility and low redox potential. Herein, we screened a range of cathode redox-active molecules and identified amine molecules as optimal to couple with the Mg anode. The properties of amine derivatives and their performances were collected to establish the correlation between molecular structures and electrochemical performances. The redox potential and solubility of these amine molecules were influenced by the π-conjugated and non-conjugated structures of amine derivatives. Density functional theory (DFT) simulations and the inverse aromatic fluctuation index (FLU −1 ) verified that conjugation had an important role in stabilizing the molecule and increasing its redox potential. Notably, tris[4-(diethylamino)phenyl]amine (TDPA) achieved the highest theoretical energy density (∼120 Wh L −1 ) due to its high solubility (∼0.9 M) and voltage (∼2.5 V vs. Mg/Mg 2+ ). We also demonstrated that ether solvents were crucial for stable, high-solubility catholytes, while bulk anions did not affect the redox potential of these p-type molecules. In a Mg-amine RFB configuration, the battery delivered 2.50 V, a specific discharge capacity of 106.5 mAh g −1 , an initial coulombic efficiency of 90.74%, and a capacity retention of 93.88% after 150 cycles.
Single crystallization remains a debated strategy for advancing Ni-rich cathode materials. While it mitigates particle cracking and improves tap density by eliminating particle boundaries, extended diffusion pathways introduce volumetric and lattice distortions, compromising electrochemical and structural stability. These challenges hinder the commercialization of high-Ni single-crystal cathodes, calling for a reassessment of their viability. Here, in this study, we report a structural design: intralattice-bonded phase single-crystal LiNi 0.92 Co 0.03 Mn 0.05 O 2 (IBP-SC92). This architecture maintains structural integrity while shortening diffusion pathways, resulting in almost zero electrochemical degradation during cycling. The robust structure and fast ion transport mitigate lattice strain, as confirmed by multiscale high-resolution diffraction and imaging techniques, preventing intragranular cracks and irreversible phase transitions. As a result, IBP-SC92 shows outstanding cycling stability, with nearly 100% capacity retention after 100 cycles in half cells and 94.5% retention after 1,000 cycles in full cells. This redefined single-crystal cathode represents a significant step towards the industrial adoption of high-energy-density materials.
All-solid-state Li–sulfur batteries (ASSLSBs) are considered promising candidates for next-generation energy storage owing to their inherent safety, high energy density, and abundant sulfur resources. However, slow redox kinetics greatly limit sulfur utilization during solid-solid sulfur reactions, leading to significant challenges to achieve efficient performance in high-mass-loading ASSLSBs. Here, operando neutron image is employed to directly visualize, for the first time, that sluggish Li + transport kinetics and the uneven distribution of Li + during cathodic reactions are critical factors limiting sulfur conversion. To address this issue, gradient cathode architectures comprising three and five layers are designed, in which catholyte concentrations are strategically varied to optimize Li-ion flux and enhance ionic conductivity of the whole composite cathode electrode. Operando neutron imaging distinctly visualizes and confirms that three-layer gradient approach significantly enhances Li-ion mobility, resulting in more uniform redox reactions and greatly improved sulfur utilization compared to traditional non-gradient structures. Consequently, the three-layer gradient cathode achieves superior rate performance and reduced electrode polarization at high sulfur mass loadings of 4.5 and 6.0 mg cm −2 . Furthermore, the applicability and scalability of this design are demonstrated in a five-layer gradient cathode architecture, achieving an impressive discharge specific capacity increase from 656 mAh g −1 (three-layer gradient) to 1232 mAh g −1 at 1/20 C for ultra-high sulfur loading of 7.5 mg cm −2 . In conclusion, this innovative gradient cathode design offers substantial advancements in understanding and overcoming Li-ion transport limitations, paving the way toward practical, high-energy-density ASSLSBs.
To address the demand for next-generation cathode materials with high energy density, upcycling LiFePO 4 into LiFe 0.75 Mn 0.25 PO 4 has attracted considerable attention. Nevertheless, existing strategies have yet to achieve both morphology and full elemental recovery under mild ambient conditions. Here, we report an upcycling route that can address this issue by combining leaching and a high-temperature treatment process. The upcycled LiFe 0.75 Mn 0.25 PO 4 exhibits enlarged lattice spacing and a high discharge plateau, and it delivers an energy density of 563.7 Wh/kg, 40.3 Wh/kg higher than recycled LiFePO 4 , which indicates the high value of the proposed upcycling strategy. At 1 C, LiFe 0.75 Mn 0.25 PO 4 also exhibits excellent cycling stability of 91% over 700 cycles. Techno-economic analysis also indicates impressive economic and environmental benefits, including 10.4% less raw materials usage and 12.2% less energy consumption and wastewater generation. This work demonstrates a scalable and economic upcycling strategy and provides a promising pathway for sustainable battery upcycling compatible with industrial conditions.
Manganese dioxide (MnO 2 ) is widely recognized as a promising material for high-energy-density energy storage systems due to its broad applicability and facile electrodeposition. However, achieving uniform, thin, and high-mass-loading MnO 2 coatings on high-surface-area electrodes remains a significant challenge. Conventional electrodeposition methods typically yield nonuniform, thick layers with poor conductivity and limited material utilization, restricting their practical use. Here, we uncover a thermodynamically engineered vanadyl/pervanadyl (VO 2+ /VO 2 + ) interface that fundamentally reshapes MnO 2 electrodeposition chemistry, enabling highly uniform and dense coatings. Here, combining in situ AFM measurement, Classical Nucleation Theory, and Johnson–Mehl–Avrami–Kolmogorov modeling, we show that this interface reduces early-stage detectable MnO 2 island size by 35-fold and shifts the MnO 2 growth from diffusion-limited to reaction-limited progressive nucleation. This thermodynamically controlled interface yields highly dense and conformal MnO 2 films with record-high mass loading of 241 mg cm –2 (1607 mg cm –3 ) on 3D-printed graphene aerogels, without compromising porosity or inducing thickness gradient. As a prototype demonstration, the resulting MnO 2 electrodes deliver record-setting volumetric performance in both capacitors (106 F cm –3 ) and Zn//MnO 2 pouch cells (162 mAh cm –3 ). Beyond energy storage, our findings demonstrate the significance of thermodynamic interface control in MnO 2 nucleation chemistry for achieving dense and uniform coatings on various substrates, with implications for electrocatalysis, semiconductor processing, and advanced materials manufacturing.