Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hot-streaks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Altitude Starting Characteristics of an Afterburner with Autoignition and Hot-streak Ignition

An investigation was conducted in an altitude test chamber at the NACA Lewis Laboratory to determine the altitude starting characteristics of an afterburner with autoignition and with hot-streak ignition. Transient afterburner ignition data were obtained over a range of altitudes from 30,000 to 50,000 feet at a flight Mach number of 0.60. Afterburner ignition with a torch igniter located axially at approximately the midpoint of the combustion chamber was possible over the entire range, but ignition ignition with a torch igniter located in the transition section 1 5/8 inches upstream of the turbine stators proved unsatisfactory at an altitude of 50,000 feet due to the inability to obtain flame through the turbine. Increasing the afterburner-inlet total pressure at a constant afterburner fuel-air ratio decreased the afterburner ignition time. Hot-streak ignition was possible within 2 seconds after the time required to obtain the preset, normal afterburner fuel pressure, whereas autoignition required 4 to 7 seconds for the range of altitudes investigated. Following the ignition there was a period of oscillatory operation existing in the engine-afterburner before steady-state operation was attained. The time required for steady-state stable operation decreased as afterburner inlet total pressure increased. The duration of oscillations also decreased with hot-streak ignition because the fuel-air mixture was ignited before a large volume of combustible mixture was accumulated in the afterburner.

Engines, Control - Turbojet↗
NASA NTRSDate not supplied

Combustor-Turbine Interactions By Using the Open National Combustion Code (OpenNCC) and the Glenn-HT Code

We develop the methodology of coupling two different computational fluid dynamic (CFD) codes, OpenNCC and Glenn-HT, in order to investigate the unsteady flow fields inside the combustor and around the first-stage stator of a high-pressure turbine (HPT) from the energy efficient engine (E 3 ) program. In our coupling strategy, OpenNCC, a time accurate unstructured mesh multi-phase combustion CFD code, is applied to the combustor region and Glenn-HT, a structured mesh CFD code designed for turbine applications, is utilized inside the HPT region. As a proof of concept, we first simulate the three-dimensional airflow over the backward facing step and compared the predicted pressure coefficient against experimental data. We then considered a Jet-A/Air combustor with the NASA single learn direct injector (LDI) as a reacting flow test case. Here, Glenn-HT is used in the downstream of the combustor and assumes that the working fluid is a single gas (i.e., air) where the properties of the gas are taken from time- and area-averaged values at the combustor exit. A fully coupled combustor-turbine simulation using both OpenNCC and Glenn-HT was conducted on the E 3 combustor and a detailed analysis done pertaining to how a realistic combustor outflow affects migration of hot-streaks and its impact on the aerodynamic behavior inside the HPT. It is found that the combustion dynamics (i.e., the switching main and pilot flame strength) significantly alters the aerodynamic behavior inside the HPT including hot-streak migration. Variations of the temperature and the velocity magnitude in the passage could be up to ±75 and ±15. These large variations are an important part of the combustor-turbine interactions, which are overlooked by a single component simulation of the HPT while imposing the steady inflow boundary condition at the HPT inlet. Finally, it is observed the strong density gradient associated with the hot-streaks and the pressure gradient at the passage significantly enhances the baroclinic torque, affecting the vorticity field.

CFD hot-streaks↗
NASA NTRS2017

Computational Study of Combustor-Turbine Interactions

The Open National Combustion Code (OpenNCC) is applied to the simulation of a realisticcombustor configuration [Energy Efficient Engine (E(exp. 3))] in order to investigate the unsteady flow fields inside the combustor and around the first stage stator of a high pressure turbine (HPT). We consider one-twelfth (24 degrees) of the full annular E(exp. 3) combustor with three different geometries of the combustor exit: one without the vane, and two others with the vane set at different relative positions in relation to the fuel nozzle (clocking). Although it is common to take the exit flow profiles obtained by separately simulating the combustor and then feed it as the inflow profile when modeling the HPT, our studies show that the unsteady flow fields are influenced by the presence of the vane as well as clocking. More importantly, the characteristics (e.g., distribution and strength) of the high temperature spots (i.e., hot-streaks) appearing on the vane significantly alters. This indicates the importance of simultaneously modeling both the combustor and the HPT to understand the mechanics of the unsteady formulation of hot-streaks.

turbines↗
NASA NTRS2017

Computational Study of Combustor-Turbine Interactions

The Open National Combustion Code (OpenNCC) is applied to the simulation of a realisticcombustor configuration (Energy Efficient Engine (E3)) in order to investigate the unsteady flow fields inside the combustor and around the first stage stator of a high pressure turbine (HPT). We consider one-twelfth (24 degrees) of the full annular E3 combustor with three different geometries of the combustor exit: one without the vane, and two others with the vane set at different relative positions in relation to the fuel nozzle (clocking). Although it is common to take the exit flow profiles obtained by separately simulating the combustor and then feed it as the inflow profile when modeling the HPT, our studies show that the unsteady flow fields are influenced by the presence of the vane as well as clocking. More importantly, the characteristics (e.g., distribution and strength) of the high temperature spots (i.e., hot-streaks) appearing on the vane significantly alters. This indicates the importance of simultaneously modeling both the combustor and the HPT to understand the mechanics of the unsteady formulation of hot-streaks.

turbines↗
NASA NTRSDate not supplied

Numerical Study of Combustor-Turbine Interactions Considering a Two-Stage High-Pressure Turbine

In this study, preliminary results are presented from the Open National Combustion Code (OpenNCC) applied to the two-stage high-pressure turbine (HTP) from the energy efficient engine (E3) program. Although the combustor is designed for efficient fuel–air mixing and a relatively uniform exit temperature profile, temporal and spatial variation in combustor exit conditions inevitably lead to hot-streaks in the HPT. These hot streaks can cause local hot spots on the HPT blade surfaces that reduce blade life. To improve understanding of these effects and the overall design of combustor and HPT, we are developing a fully-coupled combustor-turbine computational fluid dynamics (CFD) capability. Previous work has simulated the E^3 combustor at the simulated Sea-Level Take-off (SLTO) condition (P(41) = 2.4 [atm]) with and without the first-stage HPT stator included. This work addresses HPT simulations using inflow conditions based on previous simulation results of the E^3 combustor, as well as investigating the effects of spatial and temporal temperature non-uniformity of the combustor-exit flow on the HPT performance for a more realistic SLTO (P(41) = 27.4 [atm])). First, we analyze existing results from the combustor and the HPT 1st-stage stator simulation, where the unsteady hot gas coming out of the combustor exit travels between the stationary stators and then directly exits the computational domain (i.e., no effect from the rotors). Second, we simulate the HPT including the 1st and 2nd stage stators and rotors with the time-averaged, spatially-nonuniform inflow to the HPT taken from the combustor (with HPT 1st-stage stators) solution. Differences in simulations results for the flow field in the 1st-stage stator region are presented. The results of these two simulations (combustor and HPT simulated in a sequential manner) will be compared to a fully-coupled EEE combustor/HPT simulation to understand the impacts of fully-coupled simulations on combustor and HPT performance for two different operating conditions.

LES↗
NASA NTRSDate not supplied

Numerical Study of Combustor-Turbine Interactions Considering a Two-Stage High-Pressure Turbine

In this study, preliminary results are presented from the Open National Combustion Code (OpenNCC) applied to the two-stage high-pressure turbine (HTP) from the energy efficient engine (E3) program. Although the combustor is designed for efficient fuel–air mixing and a relatively uniform exit temperature profile, temporal and spatial variation in combustor exit conditions inevitably lead to hot-streaks in the HPT. These hot streaks can cause local hot spots on the HPT blade surfaces that reduce blade life. To improve understanding of these effects and the overall design of combustor and HPT, we are developing a fully-coupled combustor-turbine computational fluid dynamics (CFD) capability. Previous work has simulated the E3 combustor at the simulated Sea-Level Take-off (SLTO) condition (P41 = 2.4 [atm]) with and without the first-stage HPT stator included. This work addresses HPT simulations using inflow conditions based on previous simulation results of the E3 combustor, as well as investigating the effects of spatial and temporal temperature non-uniformity of the combustor-exit flow on the HPT performance for a more realistic SLTO (P41 = 27.4 [atm])). First, we analyze existing results from the combustor and the HPT 1st-stage stator simulation, where the unsteady hot gas coming out of the combustor exit travels between the stationary stators and then directly exits the computational domain (i.e., no effect from the rotors). Second, we simulate the HPT including the 1st and 2nd stage stators and rotors with the time-averaged, spatially-nonuniform inflow to the HPT taken from the combustor (with HPT 1st-stage stators) solution. Differences in simulations results for the flow field in the 1st-stage stator region are presented. The results of these two simulations (combustor and HPT simulated in a sequential manner) will be compared to a fully-coupled EEE combustor/HPT simulation to understand the impacts of fully-coupled simulations on combustor and HPT performance for two different operating conditions.

LES↗
NASA NTRSDate not supplied

Computational Study of Modeling Fully-Coupled Combustor-Turbine Interactions by the Open National Combustion Code (OpenNCC)

In this study, preliminary results are presented from the Open National Combustion Code (OpenNCC) applied to the two-stage high-pressure turbine (HTP) from the energy efficient engine (E3) program. Although the combustor is designed for efficient fuel–air mixing and a relatively uniform exit temperature profile, temporal and spatial variation in combustor exit conditions inevitably lead to hot-streaks in the HPT. These hot streaks can cause local hot spots on the HPT blade surfaces that reduce blade life. To improve understanding of these effects and the overall design of combustor and HPT, we proposed a sequential approach: Step 1 (combustor _ 1st stage stator), Step 2 (HPT) and Step 3 (fully-coupled EEE combustor/HPT). In this presentation, we would like to discuss the recent numerical results at two different operating conditions: the simulated Sea-Level Take-off (SLTO) condition (P41 = 2.4 [atm]) and a more realistic SLTO (P41 = 27.4 [atm])).

LES↗
NASA NTRS1997

Impact of Periodic Unsteadiness on Performance and Heat Load in Axial Flow Turbomachines

Results of an analytical and experimental investigation, directed at the understanding of the impact of periodic unsteadiness on the time-averaged flows in axial flow turbomachines, are presented. Analysis of available experimental data, from a large-scale rotating rig (LSRR) (low speed rig), shows that in the time-averaged axisymmetric equations the magnitude of the terms representing the effect of periodic unsteadiness (deterministic stresses) are as large or larger than those due to random unsteadiness (turbulence). Numerical experiments, conducted to highlight physical mechanisms associated with the migration of combustor generated hot-streaks in turbine rotors, indicated that the effect can be simulated by accounting for deterministic stress like terms in the time-averaged mass and energy conservation equations. The experimental portion of this program shows that the aerodynamic loss for the second stator in a 1-1/2 stage turbine are influenced by the axial spacing between the second stator leading edge and the rotor trailing edge. However, the axial spacing has little impact on the heat transfer coefficient. These performance changes are believed to be associated with the change in deterministic stress at the inlet to the second stator. Data were also acquired to quantify the impact of indexing the first stator relative to the second stator. For the range of parameters examined, this effect was found to be of the same order as the effect of axial spacing.

Sharma, Om P.↗
NASA NTRS2003

Advanced Signal Processing for Integrated LES-RANS Simulations: Anti-aliasing Filters

Currently, a wide variety of flow phenomena are addressed with numerical simulations. Many flow solvers are optimized to simulate a limited spectrum of flow effects effectively, such as single parts of a flow system, but are either inadequate or too expensive to be applied to a very complex problem. As an example, the flow through a gas turbine can be considered. In the compressor and the turbine section, the flow solver has to be able to handle the moving blades, model the wall turbulence, and predict the pressure and density distribution properly. This can be done by a flow solver based on the Reynolds-Averaged Navier-Stokes (RANS) approach. On the other hand, the flow in the combustion chamber is governed by large scale turbulence, chemical reactions, and the presence of fuel spray. Experience shows that these phenomena require an unsteady approach. Hence, for the combustor, the use of a Large Eddy Simulation (LES) flow solver is desirable. While many design problems of a single flow passage can be addressed by separate computations, only the simultaneous computation of all parts can guarantee the proper prediction of multi-component phenomena, such as compressor/combustor instability and combustor/turbine hot-streak migration. Therefore, a promising strategy to perform full aero-thermal simulations of gas-turbine engines is the use of a RANS flow solver for the compressor sections, an LES flow solver for the combustor, and again a RANS flow solver for the turbine section.

Schlueter, J. U.↗
NASA NTRS2005

Modeling of a Sequential Two-Stage Combustor

A sequential two-stage, natural gas fueled power generation combustion system is modeled to examine the fundamental aerodynamic and combustion characteristics of the system. The modeling methodology includes CAD-based geometry definition, and combustion computational fluid dynamics analysis. Graphical analysis is used to examine the complex vortical patterns in each component, identifying sources of pressure loss. The simulations demonstrate the importance of including the rotating high-pressure turbine blades in the computation, as this results in direct computation of combustion within the first turbine stage, and accurate simulation of the flow in the second combustion stage. The direct computation of hot-streaks through the rotating high-pressure turbine stage leads to improved understanding of the aerodynamic relationships between the primary and secondary combustors and the turbomachinery.

Hendricks, R. C.↗
NASA NTRS2005

Modeling of a Sequential Two-Stage Combustor, Supplement

A sequential two-stage, natural gas fueled power generation combustion system is modeled to examine the fundamental aerodynamic and combustion characteristics of the system. The modeling methodology includes CAD-based geometry definition, and combustion computational fluid dynamics analysis. Graphical analysis is used to examine the complex vortical patterns in each component, identifying sources of pressure loss. The simulations demonstrate the importance of including the rotating high-pressure turbine blades in the computation, as this results in direct computation of combustion within the first turbine stage, and accurate simulation of the flow in the second combustion stage. The direct computation of hot-streaks through the rotating high-pressure turbine stage leads to improved understanding of the aerodynamic relationships between the primary and secondary combustors and the turbomachinery.

Hendricks, R. C.↗
NASA NTRSDate not supplied

Numerical Investigation of Combustor-Turbine Interactions with a Two-Stage High-Pressure Turbine Including Cooling Airflows

Combustor–turbine interactions (CTIs) are investigated by performing three-dimensional unsteady simulations using a realistic combustor and high-pressure turbine (HPT) configurations from the Energy Efficient Engine (E3) program. To understand CTIs, we compare the numerically predicted flow fields from single-component simulations (Step 1: the combustor + the first-stage stator of turbine; Step 2: the two-stage HPT imposing the time-averaged flow solution from Step 1 as the inflow boundary condition) and a fully coupled combustor–turbine simulation (Step 3) at the sea-level takeoff (SLTO) condition. In addition to three previous simulations where the cooling airflows inside the HPT had been neglected for all Step 1, Step 2, and Step 3, two new simulations of Step 2 and Step 3 take into account the cooling airflows using the source team approach. In this approach, to mimic the cooling airflows, we impose the source term at a specific area of a cooling airflow hole at the solid surfaces without making a mesh of each hole. The objective of this study is twofold. One is to investigate the effect of the presence of the cooling airflows on the aerodynamics of the combustor and HPT as well as the HPT performance. The second is to perform a detailed comparison among the calculated flowfields by two different numerical schemes, the central-difference with the standard Jameson–Schmidt–Turkel (CD-JST) scheme and the AUSM scheme. There is a noticeable difference in the hot-streak distributions at the first-stage stator. In addition, depending on the choice of the numerical scheme and the presence of the cooling airflows, an occurrence of shock waves appearing at the first-stage stator is greatly influenced. Thus, this has a noticeable impact on the HPT performance. It is shown that the estimated turbine efficiencies from Step 3 are about 7 % less than the ones from Step 2.

Combustor-turbine interaction↗
NASA NTRSDate not supplied

Computational Study of Modeling Fully-coupled Combustor-Turbine Interactions by the Open National Combustion Code (OpenNCC)

We investigate the flow fields inside the combustor and the high-pressure turbine including the stator and moving rotors, from the Energy Efficient Engine (E3) program. We then compare the fully-coupled simulations results with the prior results from the sequential approach, where key performance metrics for the combustor and HPT are compared. The results will provide one example of the impact of performing fully-coupled combustor/HPT simulations relative to sequential (one-way coupled) combustor and HPT simulations.

CFD↗
NASA NTRSDate not supplied

Computational Study of Modeling Fully-coupled Combustor-Turbine Interactions by the Open National Combustion Code (OpenNCC)

We investigate the flow fields inside the combustor and the high-pressure turbine including the stator and moving rotors, from the Energy Efficient Engine (E3) program. We then compare the fully-coupled simulations results with the prior results from the sequential approach, where key performance metrics for the combustor and HPT are compared. The results will provide one example of the impact of performing fully-coupled combustor/HPT simulations relative to sequential (one-way coupled) combustor and HPT simulations.

CFD↗
NASA NTRSDate not supplied

Numerical Study of Combustor-Turbine Interactions Using Open-National Combustion Code (OpenNCC)

We investigate the flow fields inside the combustor and the high-pressure turbine including the stator and moving rotors, from the Energy Efficient Engine (E3) program. We then compare the fully-coupled simulations results with the prior results from the sequential approach, where key performance metrics for the combustor and HPT are compared. The results will provide one example of the impact of performing fully-coupled combustor/HPT simulations relative to sequential (one-way coupled) combustor and HPT simulations.

CFD↗
NASA NTRSDate not supplied

LES Simulation of Cooling Airflow of High-Pressure Turbine Using the Source Term Approach

In this study, the Open National Combustion code (OpenNCC) is applied to simulate the airflow inside the high-pressure turbine (HPT) of the energy efficient engine (EEE). The main objective of this study is to validate the proposed methodology of a three-dimensional unsteady calculation (LES) of the HPT with a moving mesh capability to capture a relative motion at the stator and rotor interface. In our previous study, the adiabatic wall assumption was made at all the solid surfaces of HPT (i.e., the cooling airflows were not included.) To relax this assumption, we implement the surface source team approach, in which we impose the source term at a specific area of a cooling airflow exit at the solid surfaces by specifying an injection angle, temperature, turbulent intensity, and mass flowrate of each cooling airflow. The beneficial feature of this approach is that it does not require a mesh for each hole. For the validation of the model, the data for EEE model is obtained from the General Electric (GE) test campaign, and the full scale warm-air rig test condition representing a test point close to the integrated core/low spool design condition is considered.

CFD Hot-streaks↗
NASA NTRSDate not supplied

Numerical Investigation of the Effect of Cooling Airflow inside High-Pressure Turbine using the Source Term Approach

In this study, the Open National Combustion code (OpenNCC) is applied to simulate the airflow inside the high-pressure turbine (HPT) of the energy efficient engine (EEE). The main objective of this study is to compare the characteristics of the HPT performance obtained by using three different approaches (Case 1: the realistic combustion products are considered at the HPT inlet, but the cooling airflows are not included, Case 2: the working fluid is assumed to be a single gas (i.e., air), and the cooling airflows are considered, Case 3: the cooling airflow and the combustion products at the HPT inlet are included). To mimic the cooling airflows at the HPT surface, we use the surface source team approach, in which we impose the source term at a specific area of a cooling airflow hole at the solid surfaces by specifying an injection angle, temperature, turbulent intensity, and mass flowrate of each cooling airflow. For the validation of the model, the data for the EEE model was obtained from the General Electric (GE) test campaign (RDG10), and the full scale warm-air rig test condition representing a test point close to the integrated core/low spool design condition was considered. This validation test was done using the stationary uniform inflow condition (i.e., the reported total temperature and total pressure). Secondly, we considered the Sea-Level Take-off (SLTO) engine condition and separately performed the combustor simulation to obtain a more realistic time-averaged, spatially-nonuniform HPT inflow condition. This work provides a better understanding the effect of the cooling airflow model with different assumptions on the HPT performance. It is found that using different working gas have a minor effect on the performance metric, however the presence of the cooling airflows significantly affects the HPT performance such as the turbine efficiency.

CFD Hot-streaks↗