SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Hydraulic valve absorbs impact energy generated in docking or joining of two large bodies by controlling energy release to avoid jarring shock. The area of exit porting presented to the hydraulic control fluid is directly proportional to the pressure acting on the fluid.
Reliability of hydraulic control systems of space vehicles
Explore the source record for details and available documents.
A general purpose math model of a servovalve controlled hydraulic actuator system is derived. The system consists of a linear actuator with unequal piston areas, a single stage servovalve, a gas charged hydraulic accumulator, and the interconnecting piping. The state equations are integrated using the Advanced Continuous Simulation Language (ACSL) for determining the system's dynamic response characteristics. Using this generalized hydraulic actuator system model, response characteristics were determined for various servovalve commands.
Pressure sensors and isolation valves act to shut down defective servochannel. Redundant hydraulic system indirectly senses failure in any of its electrical control channels and mechanically isolates hydraulic channel controlled by faulty electrical channel so flat it cannot participate in operating system. With failure-detection and isolation technique, system can sustains two failed channels and still functions at full performance levels. Scheme useful on aircraft or other systems with hydraulic servovalves where failure cannot be tolerated.
Arm assembly consisting of four flexible tubes controlled by a four-way hydraulic or pneumatic valve can bend in any direction. The flexible arm could be used for probing areas that cannot be reached by ordinary tools, handling hazardous materials, and for graph recording.
Abstract In a high‐pressure injection fault activation experiment conducted at the Mont Terri underground research laboratory in Switzerland, the transmissivity of the Opalinus Clay fault significantly increased due to opening and shearing. The fluid injection, spanning a few hours, generated a 10 m radius fault activation patch. Subsequent pressure pulse tests conducted bi‐weekly for a year revealed the gradual return of fault transmissivity to its initial state. The study utilized fluid pressure decay analysis, optical fiber monitoring, continuous active source seismic measurements and borehole displacement sensors for measuring fault displacements. The fault zone exhibited a dilation of approximately 1.4 mm, associated with both normal and tangential movements during activation, resulting in a sudden transmissivity increase from 1 × 10 −12 to 3.2 × 10 −7 m 2 /s. Early post‐activation, transient compaction and the subsequent slow compaction were observed, transitioning to an extension regime. The pressure pulse tests demonstrated a rapid transmissivity drop by more than two orders of magnitude within the first 10 days, followed by a gradual and less pronounced decrease. Plastic shear and compaction dominated the transmissivity evolution until 70 days after injection ended, followed by a period where additional factors, such as clay mineral swelling, influenced the behavior. Extrapolation suggested a sealing process taking at least 50 years after the initial activation. Plain Language Summary A field‐scale fault activation experiment offers valuable insights into the elasto‐plastic processes governing the sealing of shale faults. The experiment reveals a rapid increase in the fault's transmissivity by approximately five orders of magnitude during activation. Subsequent observations show a gradual transmissivity decrease by about three orders of magnitude post‐activation, with slow long‐term plastic shear and compaction of the fault competing against secondary processes, notably clay mineral swelling. All conceptual models employed to interpret these field data converge on the estimation that the fault's return to its initial low transmissivity state would require a minimum of 50 years. Key Points High‐pressure injection fault activation experiment at the Mont Terri underground research laboratory Continuous transmissivity measurements record self‐sealing inside a clay‐rich fault zone Transmissivity undergoes a phase of domination by slow plastic compaction and shearing during the initial post‐activation period, with mineral swelling exerting its influence over the long term
Explore the source record for details and available documents.
Hydraulic controller possessing property of automatic tracking notch filter for open loop thrust engine control
Hydraulic axisymmetric focused-jet amplifier for pneumatic digital control
Explore the source record for details and available documents.
Single rotary valve controls a circular bank of hydraulic leveling cylinders that must maintain large loads within plus or minus three arc minutes of the true vertical. Since the position of the valve spool determines the flow rate of each bank of cylinders and hence cylinder position, different flow rates may be obtained by changing the spool shape.
This paper describes the mode of operation of a control valve assembly that is used with a hydraulic pump. The operating system of the valve is modelled in a simplified form, and an analogy for hydraulic resonance of the pressure sensing system is presented. For the control valve investigated, air entrainment, length and diameter of the resonator neck, and valve mass produced the greatest shift in resonant frequency. Experimental work was conducted on the hydraulic system so that the resonance levels and frequencies could be measured and the accuracy of the theory verified. The results obtained make it possible to evaluate what changes to any of the variables considered would be most effective in driving the second harmonic frequency above the operating range.
Hydraulic actuator moves several nuclear-reactor control rods in unison. Electromagnetic pump pushes liquid lithium against ends of control rods, forcing them out of or into nuclear reactor. Color arrows show lithium flow for reactor startup and operation. Flow reversed for shutdown. Conceived for use aboard spacecraft, actuator principle applied to terrestrial hydraulic machinery involving motion of ganged rods.
Spring-loaded piston with provision for hydraulic control of spring action varies the stiffness of hydraulic control systems.
The development of the MOD-2 wind turbine through acceptance testing and initial operational evaluation is documented. Pitch control hydraulic system, yaw control system, drive train, electrical power station, control system, operations and maintenance experience, and availability are discussed.
The constraint of requiring airplanes to have inherent aerodynamic stability can be removed by using active control systems. The resulting airplane requires control system reliability approaching that of the basic airframe. Redundant control actuators can be used to achieve the required reliability, but create mechanization and operational problems. Of numerous candidate systems, two different approaches to solving the problems associated with redundant actuators which appear the most likely to be used in advanced airplane control systems are described.
The Asian Marginal Seas are interconnected by a number of narrow straits, such as the Makassar Strait connecting the Pacific Ocean with the Indian Ocean, the Luzon Strait connecting the South China Sea with the Pacific Ocean, and the Korea/Tsushima Strait connecting the East China Sea with the Japan/East Sea. Here we propose a method, the combination of the "geostrophic control" formula of Garrett and Toulany (1982) and the "hydraulic control" theory of Whitehead et al. (1974), allowing the use of satellite-observed sea-surface-height (SSH) and ocean-bottom-pressure (OBP) data for estimating interbasin transport. The new method also allows separating the interbasin transport into surface and bottom fluxes that play an important role in maintaining the mass balance of the regional oceans. Comparison with model results demonstrates that the combined method can estimate the seasonal variability of the strait transports and is significantly better than the method of using SSH or OBP alone.