Unprecedented CO2-promoted hydrogen permeation in Ni-BaZr0.1Ce0.7Y0.1Yb0.1O3-δ membrane
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
A potentially exciting material for membrane separations are metallic glass materials due to their low cost, high elastic toughness and resistance to hydrogen embrittlement as compared to crystalline Pd-based membrane systems. However, at elevated temperatures and extended operation times structural changes including partial crystallinity may appear in these amorphous metallic systems. This study reports on the investigation of time and temperature dependent crystalline phase formation in conjunction with in situ crystallization/hydrogen permeation experiments at elevated temperatures. At temperatures near 400 C a FeNi crystalline phase appears as 22 vol.% inside the host amorphous matrix and the resulting composite structure remains stable over 3 h at temperature. The hydrogen permeation at 400 C of the partially crystalline material is similar to the fully amorphous material near 5 x 10{sup -9} mol H{sub 2}/m s Pa{sup 1/2}, while ambient temperature electrochemical permeation at 25 C revealed an order of magnitude decrease in the permeation of partially crystalline materials due to differences in the amorphous versus crystalline phase activation energy for hydrogen permeation.
Not Available
Tubes of CG-27 alloy, filled with hydrogen doped with various amounts of carbon dioxide and carbon monoxide, were heated in a diesel fuel fired Stirling engine simulator materials test rig for 100 hours at 820 C and at a gas pressure of 15 MPa to determine the effectiveness of the dopants in reducing hydrogen permeation through the hot tube wall. This was done for clean as-heat treated tubes and also for tubes that had previously been exposed for 100 hours to hydrogen doped with 1.0 volume percent carbon dioxide to determine if the lower levels of dopant could maintain a low hydrogen permeation through the hot tube wall. Carbon dioxide, as a dopant in hydrogen, was most effective in reducing hydrogen permeation through clean tubes and in maintaining low hydrogen permeation after prior exposure to 1.0 volume percent carbon dioxide. Only the lowest level of carbon dioxide (0.05 volume percent) was not as effective in the clean or prior exposed tubes. Carbon monoxide as a dopant in hydrogen was less effective than carbon dioxide at a given concentration level. Of the four dopant levels studied; 1.0, 0.5, 0.2, and 0.05 volume percent carbon monoxide, only the 1.0 and 0.5 volume percent were effective in reducing and maintaining low hydrogen permeation through the CG-27.
Small area freestanding monolayer graphene has been shown to be impermeable to standard gases including hydrogen and helium.1 Several recent reports have suggested that graphene can be used as a hydrogen permeation barrier on metals.2 Those studies have relied on electrochemical hydrogen permeation measurements, which do a good job reproducing bulk permeability compared to gaseous diffusion but do not always reflect the real surface effects due to the difference in driving forces. This problem is magnified when measuring the permeability of thin coatings, which are dominated by surface effects. For this reason, we performed gas driven hydrogen permeation measurements of graphene coated metal samples. The diffusion of hydrogen through a metal can be described using Fick's and Sievert's Laws. Graphene-coated copper foils were prepared using chemical vapor deposition (CVD) with a methane precursor. Photo-reduced graphene samples were prepared by first sputtering a layer (∼15 nm) of copper on top of stainless steel foils. Graphene oxide in ethanol solutions were then drop cast on the surface and photo reduced using a neon lamp. A custom-designed apparatus has been assembled for measuring the hydrogen permeability of various materials. The operating principle of the system is as follows: A sample is sealed between the fore-sample and post-sample chambers using standard vacuum gaskets. Hydrogen is introduced into the fore sample region at varying pressures while the post sample region is maintained under high vacuum. Due to the concentration gradient, hydrogen then diffuses through the material and is detected using a quadrupole mass spectrometer. This process is repeated at several temperatures. The mass spectrometer was calibrated using an orifice with known conductance in place of the sample. Data collection and reduction were automated using scripts written in LabVIEW and Octave, respectively. We saw a decrease in the hydrogen permeability of copper after adding graphene to the surface for small temperature steps. This result is also observed when considering temperature steps of 20 K. Future Work: Apply this methodology to graphene-coated 316L stainless steel. The hydrogen permeability of 316L steel should also decrease with the addition of graphene to the surface. Determine methods for graphene defect reduction.
The effect of a specific oxidation treatment, to which a titanium specimen was subjected, on the permeation of hydrogen through the titanium specimen was studied. The oxidation treatment involved the maintenance of the specimen in an oxygen atmosphere at a temperature of 270 C for a time of four hours. It was found that the oxidation treatment has the effect of decreasing the permeation rate. However, the first power pressure dependency is not affected.
There is a rising need for the measurement and understanding of hydrogen transport properties in materials for the energy and transportation industries. The Hydrogen Permeation Analysis Tool (HyPAT) provides a user friendly interface for batch analysis of dynamic hydrogen permeation data to calculate the transport properties permeability, solubility, and diffusivity. A built in literature database provides an easy comparison to known values. A common method for measuring these hydrogen transport properties is dynamic pressure rise permeation experiments, for example, those done in the Static Gas Absorption and Permeation (SGAP) experiment at INL. Most laboratories develop individual, in-house codes for data analysis. HyPAT provides a platform that can be adopted by other user groups for such experimental analysis and significantly reduce personnel time spent performing data analysis.
Hydrogen purification is a critical industrial process, and there are ongoing efforts to develop low-cost alternatives to palladium foil membranes. Titanium nitride (TiN) is studied as an interdiffusion barrier to enable hydrogen permeation in composite palladium–vanadium membranes. TiN was deposited via reactive sputtering, and films with the desired (200) orientation were obtained in the metallic regime at 400 °C under a 200 V bias to the substrate. The permeability of thin-film TiN was determined with palladium-based sandwich structures. TiN layers up to 10 nm resulted in a minimal decrease in flux (~20%) relative to a freestanding PdCu foil, which was attributed to the interfacial resistance. At greater thicknesses, the TiN layer was rate-limiting, and it was found that the effective permeability of the sputtered TiN thin films was ~6 × 10−12 mol s−1 m−1 Pa−0.5. Composite Pd|TiN|V|TiN|Pd membranes exhibited permeability values up to three times greater than pure palladium, exhibiting stability at 450 °C for over 100 h, with the lack of intermetallic diffusion and alloy formation being confirmed with XRD. The membranes were unstable at 500 °C, which was attributed to the instability of the thin Pd layer and loss of catalytic activity.
Alloy tubes filled with hydrogen doped with various amounts of carbon monoxide, carbon dioxide, ethane, ethylene, methane, ammonia, or water were heated in a diesel fuel-fired Stirling engine simulator materials test rig for 100 hours at 21 MPa and 760 or 820 C to determine the effectiveness of the dopants in reducing hydrogen permeation through the hot tube walls. Ultra high purity (UHP) hydrogen was used for comparison. The tube alloys were N-155, A-286, Incoloy 800, Nitronic 40, 19-9DL, 316 stainless steel, Inconel 718, and HS-188. Carbon dioxide and carbon monoxide in the concentration range 0.2 to 5 vol % were most effective in reducing hydrogen permeation through the hot tube walls for all alloys. Ethane, ethylene, methane, ammonia, and water at the concentrations investigated were not effective in reducing the permeation below that achieved with UHP hydrogen. One series of tests were conducted with UHP hydrogen in carburized tubes. Carburization of the tubes prior to exposure reduced permeation to values similar to those for carbon monoxide; however, carbon dioxide was the most effective dopant.
F82H is a primary candidate of structural material and coolant pipe material in a blanket of a fusion reactor. Understanding tritium permeation behavior through F82H is important. In a normal operation of a fusion reactor, the temperature of F82H will be controlled below 550 C. degrees because it is considered that F82H can be used up to 30,000 hours at 550 C. degrees. However, it is necessary to assume the situation where F82H is heated over 550 C. degrees in a severe accident. In this study, hydrogen permeation behavior through F82H was investigated in the temperature range from 500 to 800 C. degrees. In some cases, water vapor was added in a sample gas to investigate an effect of water vapor on hydrogen permeation. The permeability of hydrogen in the temperature range from 500 to 700 C. degrees agreed well with the permeability reported by E. Serra et al. The degradation of the permeability by water vapor was not observed. After the hydrogen permeation reached in a steady state at 700 C. degrees, the F82H sample was heated to 800 C. degrees. The permeability of hydrogen through F82H sample which was once heated up to 800 C. degrees was lower than that of the original one. (authors)
Hydrogen permeation measurements have been conducted for the Incoloy 909 Ni-Fe-Co superalloy via the 'membrane' technique, in which the gaseous hydrogen at the entrance of a thin membrane is transposed through the bulk to the exit side of the membrane, at 400-810 C; the pressure range explored was 2.7 x 10 exp 3 to 1.3 x 10 exp 5 N/sq m. The lattice hydrogen solubility of Incoloy 909 is found to be only weakly temperature-dependent. These results are compared with those obtained for Incoloy 903.
Gas phase hydrogen permeation studies were conducted on hollow, cylindrical membranes of triply zone-refined alpha iron, AISI 304 austenitic stainless steel, and AISI-SAE 4130 steel in both the normalized (ferrite and carbide) and quenched and tempered (martensite) conditions. Membrane temperature was varied from less than 100 C to near 600 C and hydrogen pressure was varied. For one membrane material, normalized 4130 steel, gas phase hydrogen transport under both steady state and nonsteady state conditions was demonstrated to be controlled by lattice diffusion. Additionally, Sievert's law was shown to be applicable. For all membrane materials, expressions for the coefficients for hydrogen permeation were determined by analysis of steady state transport; the coefficients for diffusion were determined by the lag time technique applied to nonsteady state transport; and through a knowledge of the Sievert's constants, the subsurface equilibrium lattice hydrogen concentrations were determined.
Tritium permeation into and through materials poses a critical challenge for the development of nuclear fusion reactors. Minimizing tritium permeation is essential for the safe and efficient use of available fuel supplies. In this work, we present the design, construction, and validation of custom atomic layer deposition (ALD) and deuterium permeation measurement systems aimed at developing thin-film hydrogen permeation barriers. Using the ALD system, we deposited conformal $\mathrm{Al}_{2}\mathrm{O}_{3}$ films on copper foil substrates and characterized their growth behavior, morphology, and composition. ALD growth rates of ∼1.1 Å/cycle were achieved for temperatures between 100 ∘ C and 210 ∘ C. Permeation measurements on bare and alumina coated copper foils revealed a significant reduction in deuterium flux with the addition of a ∼10 nm $\mathrm{Al}_{2}\mathrm{O}_{3}$ layer. While bare copper followed diffusion-limited transport consistent with Sievert’s law, the alumina-coated samples exhibited surface-limited, pore-mediated transport with linear pressure dependence. Arrhenius analysis showed distinct differences in activation energy for the two transport regimes, and permeation reduction factors exceeding an order of magnitude were observed. These results demonstrate the potential of ALD-grown $\mathrm{Al}_{2}\mathrm{O}_{3}$ films as effective hydrogen isotope barriers and provide a foundation for future studies on film optimization and integration into fusion-relevant components.
The hydrogen infrastructure involves hydrogen production, storage and delivery for utilization with clean energy applications. Hydrogen ingress into structural materials can be detrimental due to corrosion and embrittlement. To enable safe operation in applications that need protection from hydrogen isotopes, this review article summarizes most recent advances in materials design and performance characterization of barrier coatings to prevent hydrogen isotopes’ absorption ingress and permeation. Barriers are crucial to prevent hydride formation and unwanted hydrogen effects to increase safety, materials’ lifetime and reduce cost for applications within nuclear and renewable energy. The coating may be applied on a material that requires protection from hydrogen pick-up, transport and hydride formation in hydrogen storage containers, in pipelines, spent nuclear fuel storage or in nuclear reactors. While existing, commercial coatings that have been much in use may be satisfactory for various applications, it is desirable to evaluate whether alternative coating concepts can provide a greater resistance to hydrogen isotope permeation along with other improved properties, such as mechanical strength and thermal resistance. The information presented here is focusing on recent findings within the past 5–7 years of promising hydrogen barriers including oxides, nitrides, carbon, carbide, MAX-phases and metals and their mechanical strength, hydrogen pick-up, radiation resistance and coating manufacturing techniques. A brief introduction to hydrogen permeation is provided. Knowledge gaps were identified to provide guidance for material’s research prospects.
An attempt has been made to determine the permeation rate of hydrogen in IN-100 and Waspaloy by determining the evolution rate of hydrogen from a closed capsule of the test materials. Enclosed vanadium hydride was the source of hydrogen in the capsule. The presentation discusses the treatment of data and assesses the validity of the techniques in permeation measurement. In addition to permeation experiments, the solubility and diffusion of hydrogen in IN-100 and Waspaloy were also determined. For hydrogen diffusion in Waspaloy, Delta H was 38.5 kJ and D(0) was 0.0026 sq cm/sec. For IN-100, Delta H was 68.2 kJ and D(0) was 0.059 sq cm /sec. Both IN-100 and Waspaloy exhibited limited solubility of hydrogen at pressures up to 340 atmospheres hydrogen.
Density functional theory was used to screen eleven refractory materials – two pure metals, six nitrides, and three carbides–as high-temperature hydrogen permeation barriers to prevent hydrogen embrittlement. Activation energies were calculated for atomic hydrogen (H) diffusion into the first subsurface layer from the lowest energy surface of the high-temperature phase of each candidate material. The candidate barrier materials with the highest activation energies are h-BN, c-BN, HfN, and ZrN with predicted barriers of 3.25 eV, 3.23 eV, 3.14 eV, and 2.76 eV, respectively. Strain energies, Bader charges, and density of states were calculated for the diffusing H at the relaxed initial state and the transition state to provide insight into contributing factors to high energy barriers. The diffusing H atom in materials with the highest predicted barriers are protic. In addition, interstitial H atoms induce mid-gap states in the density of states of both BN polymorphs. The nitrogen retention of each nitride material at high temperatures was predicted using nitrogen vacancy formation energies with respect to gaseous nitrogen. Experimental evaluation of nitrogen retention in h-BN, ZrN, and TiN confirmed their resistance to nitrogen loss at 1773 K. However, of these nitrides, TiN is predicted to be the least stable. This work identifies multiple promising materials that are predicted to be effective hydrogen barriers at high temperatures and that are stable at temperatures above 2700 K, with BN predicted to perform best.
The process of hydrogen transport through alpha-Ti involves simultaneous diffusion and phase boundary reactions at both surfaces, with the relative effect on each surface depending on the extent of surface contamination as well as the physical dimensions of the titanium membrane used. It is shown by the present study that hydrogen permeation in commercially pure alpha-Ti increases exponentially with temperature and is dependent on the first power of the input pressure, whether the surface is as-polished, preoxidized or prenitrided. Permeation decreases in the case of the as-polished condition if nitride or oxide films are formed at the surface in contact with source hydrogen, while increasing slightly for the same condition if such films are formed at the hydrogen exit surface.
Iron-chromium-aluminum (FeCrAl) alloys such as APMT (advanced powder metallurgy tubing) are candidate materials to replace zirconium alloys for the light water reactor fuel cladding. This alloy meets the requirements to be a material more tolerant of high-temperature accidents than the current zirconium alloys. One concern is that the use of FeCrAl may result in an increase in tritium presence in the coolant compared to the current design. The aim of the current research was to obtain effective diffusion coefficients (D eff ) for hydrogen through APMT using the Devanathan-Stachurski cell. Results showed that at 30°C the D eff value was 2.8 × 10 -8 cm 2 /s. Results also showed a linear relationship between the permeated hydrogen flux and the inverse of the test specimen thickness, which demonstrated the validity of the permeation measurements.