Search NASA⌕ Search

SEARCH · Search NASA

Results for “I&C”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Measurement and significance of the equilibrium reaction C-13/+/ + /C-12/O yields C-12/+/ + /C-13/O for alteration of the C-13/C-12 ratio in interstellar molecules

Laboratory measurements using the ion-cyclotron resonance technique yield a rate constant of 2 by 10 to the -10th power cu cm/sec at 300 K for the isotope exchange C-13(+) + (C-12)O yields C-12(+) + (C-13)O. According to the usual ideas about ion-molecule reactions, this rate constant should also be appropriate at temperatures not exceeding about 100 K. Then the observed C-13/C-12 ratio obtained from radio observation of interstellar molecules may be either larger or smaller than the actual value in the interstellar medium by factors of 2 or so. If the ratio is altered from the actual interstellar value, it will not be the same in all molecules, and CO will tend to have the highest value. The chief astronomical uncertainty for the occurrence of this isotope fractionation is the abundance of 'unobservable' molecules which can react rapidly with C(+): e.g., O2, H2O, CO2, and CH4. If their abundance is greater than about one-tenth that of CO, the isotope fractionation will be inhibited.

Watson, W. D.↗
NASA NTRS1978

H-H, C-H, and C-C NMR spin-spin coupling constants calculated by the FP-INDO method for aromatic hydrocarbons

The FP-INDO (finite perturbation-intermediate neglect of differential overlap) method is used to calculate the H-H, C-H, and C-C coupling constants in hertz for molecules of six different benzenoid hydrocarbons: benzene, naphthalene, biphenyl, anthracene, phenanthrene, and pyrene. The calculations are based on both the actual and the average molecular geometries. It is found that only the actual molecular geometries can always yield the correct relative order of values for the H-H coupling constants. For the calculated C-C coupling constants, as for the calculated C-H coupling constants, the signs are positive (negative) for an odd (even) number of bonds connecting the two nuclei. Agreements between the calculated and experimental values of the coupling constants for all six molecules are comparable to those reported previously for other molecules.

Long, S. A. T.↗
NASA NTRS1992

Intensity and linewidth measurements in the 13.7-micron fundamental bands of (C-12)2H2 and (C-12)(C-13)H2 at planetary atmospheric temperatures

The absolute intensities and collision-broadened half-widths of several lines in the P-,Q-, and R-branches of the nu5-fundamental band of (C-12)2H2 have been measured at various temperatures between 147 and 295 K employing the Doppler-limited spectral resolution (about 10 exp -4/cm) of a tunable diode laser spectrometer. The absolute intensities of R(5), R(7), R(9), and R(20) in the same fundamental belonging to (C-12)(C-13)H2 have also been measured at 294 K. The temperature dependence of the collision-broadened half-width has been determined for some of the lines broadened by planetary atmospheric gases, namely, He, Ar, H2, and N2. Four self-broadened linewidths of (C-12)2H2, as well as three H2-broadened linewidths and a self-broadened half-width of (C-12)(C-13)H2, have also been retrieved from the measurements.

Varanasi, Prasad↗
NASA NTRS1993

(C-12)/(C-13) isotope ratio in the local interstellar medium from observations of (C-13)(O-18) in molecular clouds

The paper examines the (C-12)/(C-13) isotope ratio in the solar neighborhood on the basis of observations of the (C-12)(O-18) and (C-13)(O-18) J = 1-0 transitions in four interstellar clouds located within 500 pc. The (C-12)/(C-13) ratio in these sources ranges from 57 to 74, and its weighted average is 62 +/- 4, with thermal noise and line formation uncertainties contributing about equally to the probable error. These values indicate moderate chemical evolution in the local star neighborhood since the formation of the solar system, in good agreement with model prediction of the current carbon ratio in the local interstellar medium.

Langer, William D.↗
NASA NTRS1978

Measurements of 15.11-MeV gamma-ray flux produced in the reactions C-12(p, p')-C-12*(15.11 MeV) and O-16(p, p' alpha)-C-12*(15.11 MeV)

The flux of 15.11 MeV gamma rays relative to the flux of 4.44 MeV gamma rays which are emitted from the corresponding states of C-12 are a sensitive measure of the spectrum of exciting particles in solar flares and other cosmic sources. Emission of 15.11 MeV gamma rays may result not only from the direct excitation of C-12 but also from the interaction O-16 (p,p' alpha) C-12* sup 15.11 MeV. Although the cross sections for the direct reaction was studied extensively, the cross section for the spallation interaction with O-16 is not reported in the literature. Preliminary measurements demonstrated the feasibility of measuring the production of 15.11 MeV gamma rays by proton interactions with O-16 using the University of Maryland cyclotron facility. For both carbon and oxygen targets the flux of 15.11 MeV gamma rays is being measured relative to the flux of 4.44 MeV gamma rays. The gamma ray emission from de-excitation of the giant dipole resonances is being measured.

Lapides, J. R.↗
NASA NTRS1981

Permanent magnet properties of Mn-Al-C between -50 C and +150 C

Anisotropic Mn-Al-C (Ni) magnets are potential substitutes for Alnico 5 and 8. The limited machinability of the alloy and the fact that it is cobalt-free made it particularly interesting. The low Curie point and the costly warm extrusion process needed for grain orientation are drawbacks. The objective of this study was a detailed magnetic characterization of the material for possible use in electric machinery. The principal subjects of the study were the largest extruded bars presently available, of 31 mm diameter. Easy and hard axis magnetization curves and second-quadrant recoil loop fields were measured at various temperatures ranging from -50 C to +150 C. Property variations over the cross section of a bar were also studied.

Abdelnour, Z. A.↗
NASA NTRS1987

Measurements of electron attachment lineshapes and cross sections at ultra-low electron energies for CF2Cl2, c-C4F6, c-C4F8 and c-C7F14

Electron-attachment cross sections are reported in the electron energy range 0-160 meV, and at energy resolutions of 7.0 and 7.5 meV (FWHM), for the molecules CF2Cl2 (dichlorodifluoromethane), c-C4F6 (perfluorocyclobutene), c-C4F8 (perfluorocyclobutane), and c-C7F14 (perfluoromethylcyclohexane). Use is made of the Kr photoionization method. Measured attachment lineshapes are deconvoluted from the spectral slit function, and are converted to cross sections by normalization through thermal attachment-rate constants. Comparisons are made with attachment cross sections derived from several independent sets of swarm-measured rate constants, and with collisional ionization (high-Rydberg attachment) data.

Chutjian, A.↗
NASA NTRS1992

Parathyroid hormone induces c-fos and c-jun messenger RNA in rat osteoblastic cells

PTH is a potent regulator of osteoblast gene expression, yet the nuclear events that mediate PTH action are poorly understood. We were interested in identifying immediate early genes which may regulate PTH-altered gene expression in the osteoblast. Therefore, we examined the effects of PTH on c-fos and c-jun gene expression in a rat osteoblastic cell line (UMR 106-01). Under control conditions, c-fos and c-jun mRNAs were present at low basal levels. After PTH treatment, c-fos mRNA abundance dramatically increased, with a maximal and transient response at 30 min. PTH also stimulated an increase in c-jun mRNA, but in a biphasic manner, with maximal levels at 30 min and 2 h. These responses were dose dependent, not altered by cotreatment with the protein synthesis inhibitor cycloheximide, and preceded PTH-induced expression of matrix metallo-proteinase-1 mRNA. Nuclear run-on assays demonstrated an increased rate of c-fos and c-jun transcription after PTH exposure. To determine the signal transduction pathways involved, second messenger analogs were tested for their ability to mimic the effects of PTH. 8-Bromo-cAMP and phorbol 12-myristate 13-acetate (PMA) caused increases in the abundance of c-fos and c-jun transcripts. Ionomycin had no effect on the expression of these genes. Pretreatment of the cells with PMA resulted in a decrease in basal c-jun expression, but did not alter the PTH-mediated increase in c-fos, c-jun, or matrix metalloproteinase-1 mRNAs.(ABSTRACT TRUNCATED AT 250 WORDS).

Non-NASA Center↗
NASA NTRS1991

The optical depth of the 158 micrometer (C-12 II) line: Detection of the F=1 yields 0 (C-13 III) hyperfine-structure component

The first detection of the F = 1 yields 0 hyperfine component of the 158 micrometer (C-13 II) fine structure line in the interstellar medium is reported. A twelve point intensity map was obtained of the (C-13 II) distribution over the inner 190 inch (right ascension) by 190 inch (declination) regions of the Orion nebula using an imaging Fabry-Perot interferometer. The (C-12 II)/(C-13 II) line intensity ratio varied significantly over the region mapped. It is highest (86 plus or minus 9) in the core of the Orion H II region and significantly lower (62 plus or minus 7) in the outer regions of the map, reflecting higher optical depth in the (C-12 II) line here. It is suggested that this enhanced optical depth is the result of limb brightening of the optically thin (C-13 II) line at the edges of the bowl-shaped H II region blister. If the C-12/C-13 abundance ratio is 43, the (C-12 II) line in the inner regions of the Orion nebula, has a low optical depth: tau sub 12 approximately = 0.75 plus or minus 0.25. The optical depth together with the large brightness temperature of the (C-12 II) line (approximately 160 K) requires that the excitation temperature of the P-2 sub 3/2 level be approximately 310 K, in very good agreement with the previous analysis of the physical conditions of the Orion interface region based on fine structure line intensity ratios and photodissociation region models. If the C-12/C-13 abundance ratio is 67, the line optical depth is somewhat larger (tau sub 12 approximately = 1.85), and the transition excitation temperature is somewhat smaller (approximately 190 K) than that predicted by these models. The present results therefore support values approximately = 43 for the C-12/C-13 abundance ratio in the Orion nebula.

Stacey, G. J.↗
NASA NTRS1993

Determination of (C-12)/(C-13) in the interstellar medium toward Zeta Ophiuchi and Xi Persei

The Lick Observatory Reticon (LOR) data presented in Hawkins et al. (1985) are reanalyzed in order to determine the cause of the significant discrepancy in (C-12)/(C-13) isotope ratios determined on the basis of observations of this isotope in the interstellar medium toward Zeta Ophiuchi and Xi Persei. A new set of Lick Observatory observations toward Zeta Oph are obtained using a CCD detector. The KPNO coude feed echelle spectrograph and a CCD detector are used to carry out high-resolution, high SNR ratio observations toward Zeta Oph and Xi Per. The LOR results for Zeta Oph are uncertain, ranging to 40 to 60, owing to the error in continuum placement. The KPNO results toward Zeta Oph are (C-12)H/(C-13)H(+)(0, 0) = 63 +/- 8, (C-12)H(+)/(C-13)H(+)(1, 0) = 67 +/- 19, and (C-12)N/(C-13)N = 100 + 88/- 33. Toward Xi Per, the KPNO measurements yield (C-12)H(+)/(C-13)H(+) = 49 +/- 15 from the 4232-A band, and a lower limit of 45 from the 3957-A observations.

Hawkins, Isabel↗
NASA NTRS1993

Comparison of reflectance spectra of C asteroids and unique C chondrites Y86720, Y82162, and B7904

Reflectance spectra (0.3-2.6 microns) of 11 carbonaceous (C) chondrite powders (less than 100 or less than 125 microns) including 'unique' ones Y86720, Y82162, and B7904, have been measured and compared with those of 14 C asteroids. Among those C chondrites, only three 'unique' ones had close counterparts among C asteroids (Y86720 and 1 Ceres, Y82162 and 704 Interamnia, and B7904 and 31 Euphrosyne). Mixing calculations of those C chondrites by Hapke's isotropic model were also performed to improve fits of reflectance spectra of all the 14 C asteroids. If the grain-size distributions of those asteroid surfaces are similar to those C chondrite powders, the result suggests that all tested C asteroids contain a high amount of heated C chondrite material, such as Y86720, Y82162, and B7904.

Hiroi, T.↗
NASA NTRS1972

Boundary lubrication of formulated C-ether in air to 300 deg C. 1: Phosphorus ester additives

Friction and wear measurements were made on CVM M-50 steel lubricated with three C-ether (modified polyphenyl ether) formulations in dry and wet air. Results were compared to those obtained with a formulated Type 2 ester and the C-ether base fluid. A ball-on-disk sliding friction apparatus was used. Experimental conditions were a 1-kilogram load, a 17-meter-perminute (100-rpm) surface speed, and a 25 to 300 C (77 to 572 F) disk temperature range. The C-ether base fluid and the three formulated C-ether fluids yielded lower wear than the Type 2 ester over the entire temperature range. All C-ether fluids exhibited slightly higher friction coefficients than the ester from 150 to 300 C (302 to 572 F) and similar values from 25 to 150 C (77 to 302 F). In general, lower wear rates were observed with the C-ethers when tested in wet air as compared to a dry air atmosphere.

Jones, W. R., Jr.↗
NASA NTRS1975

Boundary lubrication of formulated C-ethers in air to 300 C

Six C-ether formulations (containing organic acid and phosphorus ester additives) were tested in dry (less than 100 ppm H2O) and moist air (relative humidity 50 percent at 25 C) and temperatures from 25 to 300 C, in order to determine the boundary lubricating characteristics and to compare these results to those obtained with a fully formulated Type II ester and the unformulated C-ether base fluid. The apparatus, procedures and detailed results of the test are described. Friction and wear measurements were made on CVM M-50 steel under 1 kg load and 17 meter per minute (100 rpm) surface speed conditions, for a duration of 25 minutes. In general, the C-ether formulations exhibited higher friction coefficients than the ester from 150 to 300 C and similar or lower values from 25 to 150 C, furthermore, in most test conditions the C-ether base fluid and the six C-ether formulations yielded lower wear than the ester. Possible applications in the aerospace industry are mentioned.

Jones, W. R., Jr.↗
NASA NTRS1980

Formulation and evaluation of C-Ether fluids as lubricants useful to 260 C

Three base stocks were evaluated in bench and bearing tests to determine their suitability for use at bulk oil temperatures (BOT) from -40 C to +260 C. A polyol ester gave good bearing tests at a bulk temperature of 218 C, but only a partially successful run at 274 C. These results bracket the fluid's maximum operating temperature between these values. An extensive screening program selected lubrication additives for a C-ether (modified polyphenyl ether) base stock. One formulation lubricated a bearing for 111 hours at 274 C (BOT), but this fluid gave many deposit related problems. Other C-ether blends produced cage wear or fatigue failures. Studies of a third fluid, a C-ether/disiloxane blend, consisted of bench oxidation and lubrication tests. These showed that some additives react differently in the blend than in pure C-ethers.

Clark, F. S.↗
NASA NTRS1975

Boundary lubrication of formulated C-ethers in air to 300 C

Friction and wear measurements were made in dry and moist air on CVM M-50 steel lubricated with six C-ether formulations containing phosphorus ester and organic acid additives. Results were compared to those obtained with a formulated Type 2 ester and the C-ether base fluid. A ball-on-disk sliding friction apparatus was used. Experimental conditions were a 1-kilogram load, 17 meter-per-minute (100 rpm) surface speed, and a 25 to 300 C disk temperature range. The C-ether base fluid and the C-ether formulations yielded lower wear than the ester under most test conditions. The C-ether formulations exhibited higher friction coefficients than the ester from 150 to 300 C and similar or lower values from 25 to 150 C.

Jones, W. R., Jr.↗