Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPROVED COMPOSITIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Development of Improved Composite Pressure Vessels for Hydrogen Storage

Hexagon Lincoln started this DOE project as part of the Hydrogen Storage Engineering Center of Excellence (HSECoE) contract on 1 February 2009. The purpose of the HSECoE was the research and development of viable material based hydrogen storage systems for on-board vehicular applications to meet DOE performance and cost targets. A baseline design was established in Phase 1. Studies were then conducted to evaluate potential improvements, such as alternate fiber, resin, and boss materials. The most promising concepts were selected such that potential improvements, compared with the baseline Hexagon Lincoln tank, resulted in a projected weight reduction of 11 percent, volume increase of 4 percent, and cost reduction of 10 percent. The baseline design was updated in Phase 2 to reflect design improvements and changes in operating conditions specified by HSECoE Partners. Evaluation of potential improvements continued during Phase 2. Subscale prototype cylinders were designed and fabricated for HSECoE Partners’ use in demonstrating their components and systems. Risk mitigation studies were conducted in Phase 3 that focused on damage tolerance of the composite reinforcement. Updated subscale prototype cylinders were designed and manufactured to better address the HSECoE Partners’ requirements for system demonstration. Subscale Type 1, Type 3, and Type 4 tanks were designed, fabricated and tested. Laboratory tests were conducted to evaluate vacuum insulated systems for cooling the tanks during fill, and maintaining low temperatures during service. Full scale designs were prepared based on results from the studies of this program. The operating conditions that developed during the program addressed adsorbent systems operating at cold temperatures. A Type 4 tank would provide the lowest cost and lightest weight, particularly at higher pressures, as long as issues with liner compatibility and damage tolerance could be resolved. A Type 1 tank might be the choice if the liner and damage tolerance issues were not resolved, particularly if the operating pressure was reduced.

08 HYDROGEN↗
DOE OSTI2023

Compositionally complex perovskite oxides: Discovering a new class of solid electrolytes with interface-enabled conductivity improvements

Compositionally complex ceramics (CCCs), including high-entropy ceramics, offer a vast, unexplored compositional space for materials discovery. Herein, we propose and demonstrate strategies for tailoring CCCs via a combination of non-equimolar compositional designs and control of grain boundaries (GBs) and microstructures. Using oxide solid electrolytes for all-solid-state batteries as an example, we have discovered a class of compositionally complex perovskite oxides (CCPOs) with improved lithium ionic conductivities beyond the limit of conventional doping. For example, we demonstrate that the ionic conductivity can be improved by >60% in (Li 0.375 Sr 0.4375 )(Ta 0.375 Nb 0.375 Zr 0.125 Hf 0.125 )O 3-δ compared with the (Li 0.375 Sr 0.4375 )(Ta 0.75 Zr 0.25 )O 3-δ (LSTZ) baseline. Furthermore, the ionic conductivity can be improved by another >70% via quenching, achieving >270% of the LSTZ. Notably, we demonstrate GB-enabled conductivity improvements via both promoting grain growth and altering GB structures through compositional designs and processing. In a broader perspective, this work suggests new routes for discovering and tailoring CCCs for energy storage and many other applications.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Characterization of Ceramic Material Produced From a Cold Crucible Induction Melter Test

This report summarizes the results from characterization of samples from a melt processed surrogate ceramic waste form. Completed in October of 2014, the first scaled proof of principle cold crucible induction melter (CCIM) test was conducted to process a Fe-hollandite-rich titanate ceramic for treatment of high level nuclear waste. X-ray diffraction, electron microscopy, inductively coupled plasma-atomic emission spectroscopy (and inductively coupled plasma-mass spectroscopy for Cs), and product consistency tests were used to characterize the CCIM material produced. Core samples at various radial locations from the center of the CCIM were taken. These samples were also sectioned and analyzed vertically. Together, the various samples were intended to provide an indication of the homogeneity throughout the CCIM with respect to phase assemblage, chemical composition, and chemical durability. Characterization analyses confirmed that a crystalline ceramic with desirable phase assemblage was produced from a melt using a CCIM. Hollandite and zirconolite were identified in addition to possible highly-substituted pyrochlore and perovskite. Minor phases rich in Fe, Al, or Cs were also identified. Remarkably only minor differences were observed vertically or radially in the CCIM material with respect to chemical composition, phase assemblage, and durability. This recent CCIM test and the resulting characterization in conjunction with demonstrated compositional improvements support continuation of CCIM testing with an improved feed composition and improved melter system.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization and pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Rendering and Compositing Infrastructure Improvements to VisIt for Insitu Rendering

Compared to posthoc rendering, insitu rendering often generates larger numbers of images, as a result rendering performance and scalability are critical in the insitu setting. In this work we present improvements to VisIt's rendering and compositing infrastructure that deliver increased performance and scalability in both posthoc and insitu settings. We added the capability for alpha blend compositing and use it with ordered compositing when datasets have disjoint block domain decomposition to optimize the rendering of transparent geometry. We also made improvements that increase overall efficiency by reducing communication and data movement and have addressed a number of performance issues. We structured our code to take advantage of SIMD parallelization and use threads to overlap communication and compositing. We tested our improvements on a 20 core workstation using 8 cores to render geometry generated from a $256^3$ cosmology dataset and on a Cray XC31 using 512 cores to render geometry generated from a $2000^2 \times 800$ plasma dataset. Our results show that ordered compositing provides a speed up of up to $4 \times$ over the current sort first strategy. The other improvements resulted in modest speed up with one notable exception where we achieve up to $40 \times$ speed up of rendering and compositing of opaque geometry when both opaque and transparent geometry are rendered together. We also investigated the use of depth peeling, but found that the implementation provided by VTK is substantially slower,both with and without GPU acceleration, than a local camera order sort.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2017

Composites with improved absorption of noise and vibration

The development of composites based on thermosetting resins with improved vibration and noise absorption is considered. Mathematical and topological models are proposed to describe the influence of the composition on the vibration and noise absorption and elastic properties of the composites. The composition of filled epoxy, polyester, and polyurethane vibration-absorbing composites is optimized in terms of their loading, dynamic, and economic characteristics.

42 ENGINEERING↗
DOE OSTI2022

Fabrication of Advanced Nanocarbon-Metal Composites for Improved Energy Efficiency

We fabricated nanocarbon metal composites (NCMC) of Al alloys with a process called “electrocharging assisted process” (EAP). This method consists of the application of a high current to a mixture of liquid metal and carbon particles. We investigated aluminum alloys (6061 and 1350) and used activated carbon and graphite powder as the source of carbon. The high current induces the formation of carbon chains and ribbons in the liquid metal. Upon solidification of the metal an epitaxial relation between the carbon nanostructures and the metal lattice is produced. The purpose of the project was to find the parameters during the reaction that would give rise to a high density of nanoribbons extending throughout the metal such that the electrical conductivity and the mechanical strength of the composite increased and that the method could be extended to large scale manufacturing. For this purpose, we designed two reactors for the incorporation of nanocarbon ribbons in aluminum metal. The first reactor was designed to have more control of the region with the high current density. However, there were problems with getting good mixing of the carbon in small volumes. A second reactor was designed with a stirrer that allowed for better mixing of the carbon by the introduction of argon gas through the shaft of the stirrer. NCMC were fabricated with a series of parameters to understand the role of current, time of applied current, type and shape of the cathode electrode and stirring speed of the mixture. We analyzed the composites by Raman scattering to gain information on the crystallite size of the nanocarbon, XRD to obtain the crystal structure of the composite, SEM and TEM to characterize the grain size of the aluminum grains and the quality of the crystal structure. We also measured the electrical conductivity and mechanical properties of selected samples. The nanocomposites showed increase in crystallite size of the nanocarbon with a linear dependence of the crystallite size on the duration of the applied current. There is a minimum current density necessary for the crystallite size to increase compared to the ~ 10 nm size of the activated carbon source used in the fabrication. The electrical conductivity of the nanocomposites increased with crystallite size of the nanocarbon and with the concentration of converted carbon. The maximum increase in electrical conductivity was 5.7% above the baseline for samples with ~ 4 wt % nanocarbon with crystallite size larger than 30 nm. These samples presented a hardness ~ 8% higher than the baseline samples with no carbon.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2026

Additively Reinforced Thermoformable PETG Composite Sheets for Improved Structural Efficiency

Thermoforming of short-fiber reinforced thermoplastic sheets offers a viable pathway for producing lightweight composite components; however, inherent anisotropy in fiber-reinforced sheets can limit structural performance under multidirectional loading. In this work, short carbon fiber, glass fiber, and hybrid fiber–reinforced PETG sheets were evaluated as candidate feedstock materials for thermoforming, with flexural and tensile testing performed both along the primary fiber direction and in the off-axis orientation to establish baseline stiffness, strength, and anisotropy. As expected, short carbon fiber PETG exhibited the highest stiffness and strength in the primary fiber direction, while all systems showed reduced performance in the off-axis direction. This off-axis performance reduction provides clear justification for the use of additive reinforcement when such thermoformed sheets are intended for structural applications. The intended manufacturing sequence involves thermoforming the reinforced sheet first, followed by the application of additively manufactured lattice reinforcement; therefore, the reinforcement strategy does not impose limitations on sheet formability during thermoforming. Post-forming lattice reinforcement significantly reduced load-normalized displacement by approximately 95–99% relative to non-reinforced sheets and improved weight-normalized stiffness by ~70%. These findings demonstrate that geometry-driven additive reinforcement can effectively compensate for off-axis property reductions in thermoformed PETG composites, enabling enhanced multidirectional structural performance without compromising manufacturability.

Talabi, Isaac [ORNL] (ORCID:0000000340215594)↗
DOE OSTI2024

Chemical changes from N-doped graphene and Metal-Organic Frameworks to N-G/MOF composites for improved electrocatalytic activity

Integrating N doped graphene (N G) with Metal Organic Frameworks (MOFs) enhances catalytic activity for oxygen reduction reaction (ORR), often exceeding both the performances of their precursors and, in some cases, even PGM based catalysts. However, the factors driving this improved catalytic activity in N G/MOF composites remain unexplored, particularly from the perspective of the chemical changes. To investigate the chemical changes in N G and MOF upon their integration and the implications of these changes on ORR catalytic activity, an N G/MOF was synthesized from N G with a MOF (ZIF 8) following a mechanochemical wet ball milling process. The N G, ZIF 8, and N G/MOF samples were examined for changes in elemental composition, chemical state of carbon, different nitrogen and carbon bonds, and other chemical interactions. In the N G/MOF catalyst, compared to its N G and ZIF 8 precursors, the relative oxygen content increased, indicating the formation of additional oxygen containing groups. The C 1s peak shifted to a lower binding energy in N G/MOF, suggesting changes in the overall chemical or oxidation state of the carbon atoms. Besides, the increase in pyridinic N functional groups in N G/MOF points to the formation of additional active sites. Furthermore, the formation of C Zn bonds in N G/MOF suggests the probable emergence of single atom Zn sites, while the increase in C=O bonds points to the formation of carboxyl or carbonyl groups. These chemical changes could be linked to the enhanced electrocatalytic activity of the N G/MOF composite for ORR. In conclusion, this study may also be beneficial for other research focused on developing composite catalysts involving various N G and MOF materials.

25 ENERGY STORAGE↗
DOE OSTI2019

Manufacturing of Ultra-Fine Particle Coal Fly Ash–A380 Aluminum Matrix Composites with Improved Mechanical Properties by Improved Ring Milling and Oscillating Microgrid Mixing

An experimental study is presented of ultra-fine coal fly ash (CFA) aluminum matrix composites produced by successive high-power ring milling of CFA, oscillating microgrid mixing of the CFA–aluminum melt, gravity casting and rapid cooling. Samples corresponding to different CFA concentrations and particle size distributions (1 μm average, or less) are produced and subjected to microstructural and mechanical characterization, including tensile, compressive, impact, hardness and wear testing. While the usual trade-off between increased strength and hardness and reduced ductility and toughness is observed, the obtained ultra-fine particle composites are confirmed to have overall improved mechanical properties compared to composites with larger size particles previously produced by ball milling.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Synthesis and characterization of sulfur–carbon–vanadium pentoxide composites for improved electrochemical properties of lithium–sulfur batteries

Highlights: • A wet ball milling was conducted to synthesis S–C–V{sub 2}O{sub 5} composite electrode. • V{sub 2}O{sub 5} additive led to further improve electrochemical performance of S-cathode. • S–C–V{sub 2}O{sub 5} composite electrode exhibited a first discharge capacity of 951 mAh g{sup −1}. • The electrode (60 wt.%—S, 30 wt.%—V{sub 2}O{sub 5}, 10 wt.%—C) showed best battery performance. - Abstract: Sulfur (S)–carbon (C)–vanadium pentoxide (V{sub 2}O{sub 5}) composites were prepared by wet ball milling, and their physical and electrochemical properties were evaluated. Firstly, the effect of the carbon content of S–C composite electrodes on their physical and electrochemical properties was investigated. The S–C composite electrode with 60 wt.% S delivers a first discharge capacity of 1077 mAh g{sup −1}. However, its capacity markedly decreases to 606 mAh g{sup −1} after 10 cycles, which corresponds to a capacity fading rate of 47 mAh g{sup −1} per cycle. To improve the electrochemical performance of the S–C composite electrode, carbon was partially replaced by V{sub 2}O{sub 5}. The S–C–V{sub 2}O{sub 5} composite electrode with a composition of 60 wt.%—S, 30 wt.%—V{sub 2}O{sub 5} and 10 wt.%—C exhibits a lower capacity fading rate of 23 mAh g{sup −1} per cycle in the first 10 cycles and better capacity retention than the S–C composite electrode over 50 cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Nickel-Coated Super-Aligned Carbon Nanotube Reinforced Copper Composite for Improved Strength and Conductivity

Nickel (Ni)-coated super-aligned carbon nanotube (SACNT) films-reinforced copper (Cu) matrix composites were fabricated by electrodeposition. The microstructure, mechanical property and electrical conductivity of the prepared composites have been studied systematically. The results show that the mechanical properties of SACNT/Cu were significantly improved by coating SACNT with Ni. When the volume fraction of SACNT is 10.0%, the tensile strength and yield strength of the composite can reach 477.8 and 295.5 MPa, respectively, corresponding to 147 and 170% improvement compared to pure Cu prepared by the same method. Meanwhile, due to the super-aligned arrangement of SACNTs and the homogeneous distribution of Ni, which is not mixing or dissolving with Cu, the conductivities of all the Ni-coated SACNT-reinforced Cu composites are above 58% IACS, which is about 4 times higher than the results in previous research. The enhancement of the strength of the SACNT/Cu composites comes from the combined contribution of load transfer and grain refinement strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Poly(vinylidene fluoride)/ CaCu{sub 3}Ti{sub 4}O{sub 12} and La doped CaCu{sub 3}Ti{sub 4}O{sub 12} composites with improved dielectric and mechanical properties

Highlights: • High ϵ′ PVDF/CCTO and La doped CCTO composites prepared by Extrusion. • With addition of ceramic, there is substantial increase in the ϵ′ of matrix PVDF. • Composites exhibit double relaxation behavior. - Abstract: Melt extrusion process has been used to prepare high relative permittivity, ϵ' PVDF–CCTO and PVDF–LaCCTO composites. Phase composition has been studied using powder X-ray diffraction (XRD). Microstructural, dielectric and mechanical properties have also been studied. Young's modulus of PVDF increases with the ceramic reinforcement. Dielectric measurements are made in the frequency range 10{sup −2}–10{sup 6} Hz using two probe Novocontrol impedance analyser (ZG4) from room temp to 120 °C to study the dielectric relaxation. There is a substantial increase in ϵ' of the matrix PVDF on addition of LaCCTO.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Intrinsic self-stressing and low carbon Engineered Cementitious Composites (ECC) for improved sustainability

Highlights: • A self-stressing criterion for ECC was established and experimentally verified. • An intrinsic self-stressing ECC was developed by utilizing LC3 and CSA cement. • Initial maximum expansion and later expansion loss were successfully tailored. • Expansion mechanism was identified by XRD patterns. • Self-stressing ECC has 64% of the carbon footprint of conventional concrete. Engineered Cementitious Composites (ECC) is an emerging cementitious composite material with ultra-high ductility. However, its higher cement dosage limits its material greenness and leads to concerns with drying shrinkage. In this research, an ECC utilizing limestone calcined clay cement (LC3) and calcium sulphoaluminate cement (CSA) is investigated, focusing on minimizing the material's embodied carbon while enhancing its durability with intrinsic self-stressing functionality. A self-stressing criterion is theoretically established and experimentally verified. X-ray diffraction patterns reveal an ettringite quantity that modulates the initial expansion and later expansion-reversal of LC3-CSA-ECC to support a persistent self-stressing mechanism. LC3-CSA-ECC has a lower (64%) carbon footprint and similar embodied energy compared to conventional concrete. When combined with the durability advantage (tiny crack, high ductility of 5.5%, and self-stressing function), this low carbon self-stressing ECC holds promise as a sustainable repair material that lowers the embodied and operational carbon in civil infrastructure.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Crystallographically uniform arrays of ordered (In)GaN nanocolumns

In this work, through a comparative study of self-assembled (SA) and selective area grown (SAG) (In)GaN nanocolumn (NC) ensembles, we first give a detailed insight into improved crystallographic uniformity (homogeneity of crystallographic tilts and twists) of the latter ones. The study, performed making use of: reflective high energy electron diffraction, X-ray diffraction and scanning electron microscopy, reveals that unlike their SA counterparts, the ensembles of SAG NCs show single epitaxial relationship to both sapphire(0001) and Si(111) underlying substrates. In the second part of the article, making use of X-ray diffraction, we directly show that the selective area growth leads to improved compositional uniformity of InGaN NC ensembles. This further leads to improved spectral purity of their luminescence, as confirmed by comparative macro-photoluminescence measurements performed on SA and SAG InGaN NC ensembles. An improved crystallographic uniformity of NC ensembles facilitates their integration into optoelectronic devices, whereas their improved compositional uniformity allows for their employment in single-color optoelectronic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Friction stir weld tools having fine grain structure

Tools for friction stir welding can be made with fewer process steps, lower cost techniques, and/or lower cost ingredients than other state-of-the-art processes by utilizing improved compositions and processes of fabrication. Furthermore, the tools resulting from the improved compositions and processes of fabrication can exhibit better distribution and homogeneity of chemical constituents, greater strength, and/or increased durability. In one example, a friction stir weld tool includes tungsten and rhenium and is characterized by carbide and oxide dispersoids, by carbide particulates, and by grains that comprise a solid solution of the tungsten and rhenium. The grains do not exceed 10 micrometers in diameter.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Flammability and thermal stability of thermoplastic-based composites filled with natural carbon

This investigation characterized flammability and thermal stability for a novel sustainable composite engineered for use in building applications. Flammability and thermal stability of coal plastic composites composed of coal (40–60 wt.%) and high-density polyethylene were compared to commercial wood–plastic composites. Pyrolysis thermogravimetric analysis results indicated that coal plastic composites possessed a single-step decomposition and higher char residue, while wood–plastic composites had two-step decomposition, with the first peak occurring at much lower temperatures. Thermogravimetric analyses in air suggest coal plastic composites, compared to wood–plastic composites and neat high-density polyethylene, were more thermally stable. Flash ignition temperatures for coal plastic composites were higher than high-density polyethylene and wood–plastic composites, while self-ignition temperatures were in the same range as wood–plastic composites. Rate of burning data indicated coal plastic composites were slower burning than wood–plastic composites, with increasing coal content slowing burning rate by 19.9%–27.6%. Cone calorimeter testing showed 27% and 59% reduction in total heat release and total smoke release as coal content increased while coal plastic composite with 60 wt.% coal possessed lower overall flammability in comparison with predominant commercially available wood–plastic composite products. Coal improved composite overall thermal stability and flammability by acting as char former and foaming agent.

Engineering↗