Search NASA⌕ Search

SEARCH · Search NASA

Results for “INDIUM ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Local Order in Liquid Gallium–Indium Alloys

Liquid metals such as eutectic Ga–In alloys have low melting points and low toxicity and are used in catalysis and micro-robotics. This study investigates the local atomic structure of liquid gallium-indium alloys by a combination of density measurements, diffraction data, and Monte-Carlo simulation via the empirical potential structure refinement approach. A high-Q shoulder observed in liquid Ga is related to structural rearrangements in the second coordination shell. Structure analysis found coordination environments close to a random distribution for eutectic Ga–In alloy, while electronic effects appear to dominate the mixing enthalpy.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Directional Solidification of Monotectic and Hypermonotectic Aluminum-indium Alloys Under Micron-g

The objective of this program is to analyze the mechanisms involved in the composite solid structure formation obtained from a miscibility gap alloy under microgravity. The metallic system aluminum-indium was chosen for its low critical temperature, broad miscibility gap, and rather well-known thermodynamic properties. The experiment was performed aboard the Salyut-7 spacecraft. The theories of capture of particulates by an advancing front were not able to explain the observations made on SPAR and Salyut-7 experiments. A new model was developed based on the filtration theory considering the globules population: the solid/liquid interface is like a filter of negligible thickness for the globules and its efficiency is limited by a pressure barrier measured for Al-In alloys by ground based experiments. The Materials Experiment Assembly (MEA)-3 experiment was consequently adjusted to take into account the new model. The behavior of the globules in an interacting population on the solid front is, of course, an essential factor in the theory. The theory is at present being completed by results obtained by the Laboratoire d'Aerothermique of Meudon. The hydrodynamic and thermal interactions between pairs of globules placed in a temperature gradient have been calculated showing a large reduction of the Marangoni effect compared to the isolated globule. Physico-chemical properties of metallic liquid interface are currently being investigated.

Potard, C.↗
DOE OSTI2020

Effect of indium alloying on the charge carrier dynamics of thick-shell InP/ZnSe quantum dots

In this work, thick-shell InP/ZnSe III–V/II–VI quantum dots (QDs) were synthesized with two distinct interfaces between the InP core and ZnSe shell: alloy and core/shell. Despite sharing similar optical properties in the spectral domain, these two QD systems have differing amounts of indium incorporation in the shell as determined by high-resolution energy-dispersive x-ray spectroscopy scanning transmission electron microscopy. Ultrafast fluorescence upconversion spectroscopy was used to probe the charge carrier dynamics of these two systems and shows substantial charge carrier trapping in both systems that prevents radiative recombination and reduces the photoluminescence quantum yield. The alloy and core/shell QDs show slight differences in the extent of charge carrier localization with more extensive trapping observed in the alloy nanocrystals. Despite the ability to grow a thick shell, structural defects caused by III–V/II–VI charge carrier imbalances still need to be mitigated to further improve InP QDs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Design of Dilute Palladium–Indium Alloy Catalysts for the Selective Hydrogenation of CO 2 to Methanol

Adding small amounts of a more reactive dopant metal to a more selective host metal is a well-known strategy for promoting the catalytic reactivity of the latter without sacrificing its selectivity. While substantial attention has been given to coinage metal hosts for activating individual C–H or O–H bonds, less attention has been given to more exotic metals, such as indium, which is highly selective in the complex hydrogenation of CO 2 to methanol. Herein, we describe the synthesis and properties of Pd–In alloys containing Pd in various states of aggregation (isolated atom, small clusters, and extended clusters) assessed through various characterization methods. These materials exhibit unique catalytic behaviors, with Pd promoting both the reaction rate and methanol selectivity in all cases, though its efficacy is highest when Pd is present in small clusters. Here, the inefficiency of high Pd loadings is due in part to losses in Pd accessibility, while the importance of aggregated vs isolated Pd is theorized to result from accelerated H 2 activation. Methods used to synthesize more conventional dilute-limit and single-atom alloy catalysts can, therefore, be extended to non-coinage metal hosts to promote and control more complex chemistries, though the roles of ensemble size may greatly differ.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Sputtering of the gallium-indium eutectic alloy in the liquid phase

Watson and Haff (1980) have discussed a theory which is designed to explain quantitatively isotopic fractionation effects observed during sputtering of simple or complex targets. This theory is based on the assumption that most of the atoms sputtered from a surface originate in the top monolayer. The present investigation is mainly concerned with a direct experimental test of that assumption. The sputtering of both solid and liquid phases of gallium, indium, and the gallium-indium eutectic alloy is studied. Results obtained with the aid of ion scattering and Auger spectroscopy show that, in agreement with rough theoretical expectations, the surface monolayer of a gallium-indium alloy with 16.5 percent indium in bulk contains more than 94 percent indium, while the next layer can be only slightly enriched.

Dumke, M. F.↗
NASA NTRS1979

SPAR 5 experiment no. 74-30 agglomeration in immiscible liquids

The influence of gravity, cooling rate, and composition on the macro-and microstructure of liquid phase immiscible alloys were researched. Aluminum indium alloys of compositions 30, 40, 70, and 90 weight percent indium were processed aboard two sounding rocket flights, SPAR 2 and SPAR 5. Radiographic and metallographic examination of the SPAR 2 flight and ground base samples showed the expected separation at lg of the ground base alloys into indium rich and aluminum rich layers. The flight alloys produced an aluminum rich core surrounding by indium rich metal. The results obtained from the SPAR 5 40 and 70 weight percent indium alloys were essentially identical to those from SPAR 2. The 30 and 90 weight percent indium alloys also showed massive separation into configuration similar to the 40 and 70 weight percent indium alloys. The 90 weight percent indium alloy showed additional evidence that surface tension induced droplet migration had occurred in this alloy which could at least in part account for the observed structures.

Gelles, S.↗
NASA NTRS1992

Experiments with the low melting indium-bismuth alloy system

The following is a laboratory experiment designed to create an interest in and to further understanding of materials science. The primary audience for this material is the junior high school or middle school science student having no previous familiarity with the material, other than some knowledge of temperature and the concepts of atoms, elements, compounds, and chemical reactions. The objective of the experiment is to investigate the indium-bismuth alloy system. Near the eutectic composition, the liquidus is well below the boiling point of water, allowing simple, minimal hazard casting experiments. Such phenomena as metal oxidation, formation of intermetallic compound crystals, and an unusual volume increase during solidification could all be directly observed. A key concept for students to absorb is that properties of an alloy (melting point, mechanical behavior) may not correlate with simple interpolation of properties of the pure components. Discussion of other low melting metals and alloys leads to consideration of environmental and toxicity issues, as well as providing some historical context. Wetting behavior can also be explored.

Krepski, Richard P.↗
NASA NTRS1990

An x ray photoelectron spectroscopy study of Au(x)In(y) alloys

Four gold-indium alloys were studied by x ray photoelectron spectroscopy. The binding energies and intensity ratios of the Au 4f7/2 and In 3d5/2 core levels were determined for the bulk alloy compositions of Au(10 percent In), Au3In, AuIn, and AuIn2. These values were determined for the native oxides on the materials, for the surfaces prepared by ion bombardment to remove the oxide and for surfaces scraped in-situ with a ceramic tool to expose the bulk composition. These results furnish calibration values that allow determination of the composition of thin films of this alloy system. In addition the binding energies add to the data base for understanding the effect of alloying on core level binding energies. As an illustration, these results are used to determine the composition of a series of alloy films formed by incongruent evaporation of an alloy charge.

Jayne, Douglas T.↗
DOE OSTI2026

Bandgap Engineering of Ga 2 O 3 by MOCVD Through Alloying with Indium

Ga 2 O 3 and In 2 O 3 are vital semiconductors with current and future electronic device applications. Here, we study the alloying of In 2 O 3 and Ga 2 O 3 (IGO) and the associated changes in structure, morphology, band gap, and electrical transport properties. Undoped films of IGO were deposited on sapphire substrates with varying indium (In) percentage from zero to 100% by metal-organic chemical vapor deposition (MOCVD). Some films were annealed in H 2 to induce electrical conductivity. The measurements showed the optical band gap decreased by adding In; this was confirmed by density functional (DFT) calculations, which revealed that the nature of the valence band maximum and conduction band minimum strongly relate to the chemistry and that the band gap drops by adding In. The as-grown films were highly resistive except for pure In 2 O 3 , which possesses p-type conductivity, likely arising from In vacancy-related acceptor states. N-type conductivity was induced in all films after H-anneal. DFT calculations revealed that the presence of In decreases the electron effective mass, which is consistent with the electrical transport measurements that showed higher electron mobility for higher In percentage. The work revealed the successful band gap engineering of IGO and the modification of its band structure while maintaining high-quality films by MOCVD.

36 MATERIALS SCIENCE↗
NASA NTRS1998

High Temperature - Thin Film Strain Gages Based on Alloys of Indium Tin Oxide

A stable, high temperature strain gage based on reactively sputtered indium tin oxide (ITO) was demonstrated at temperatures up to 1050 C. These strain sensors exhibited relatively large, negative gage factors at room temperature and their piezoresistive response was both linear and reproducible when strained up to 700 micro-in/in. When cycled between compression and tension, these sensors also showed very little hysteresis, indicating excellent mechanical stability. Thin film strain gages based on selected ITO alloys withstood more than 50,000 strain cycles of +/- 500 micro-in/in during 180 hours of testing in air at 1000 C, with minimal drift at temperature. Drift rates as low as 0.0009%/hr at 1000 C were observed for ITO films that were annealed in nitrogen at 700 C prior to strain testing. These results compare favorably with state of the art 10 micro-m thick PdCr films deposited by NASA, where drift rates of 0.047%/hr at 1050 C were observed. Nitrogen annealing not only produced the lowest drift rates to date, but also produce the largest dynamic gage factors (G = 23.5). These wide bandgap, semiconductor strain sensors also exhibited moderately low temperature coefficients of resistance (TCR) at temperatures up to 1100 C, when tested in a nitrogen ambient. A TCR of +230 ppm/C over the temperature range 200 C < T < 500 C and a TCR of -469 ppm/C over the temperature range 600 C < T < 1100 C was observed for the films tested in nitrogen. However, the resistivity behavior changed considerably when the same films were tested in oxygen ambients. A TCR of -1560 ppm/C was obtained over the temperature range of 200 C < T < 1100 C. When similar films were protected with an overcoat or when ITO films were prepared with higher oxygen contents in the plasma, two distinct TCR's were observed. At T < 800 C, a linear TCR of -210 ppm/C was observed and at T > 800 C, a linear TCR of -2170 DDm/C was observed. The combination of a moderately low TCR and a relatively large gage factor make these semiconducting oxide films promising candidates for the active strain elements in high temperature thin film strain gages, particularly in applications where static strain measurement is desired.

Gregory, Otto J.↗
NASA NTRS1989

Solidification processing of monotectic alloy matrix composites

Directionally solidified aluminum-indium alloys of the monotectic composition were found to form an in situ rod composite which obeys a lambda exp 2 R = constant relation. The experimental data shows good agreement with previously reported results. A theoretical boundary between cellular and dendritic growth conditions was derived and compared with experiments. The unique wetting characteristics of the monotectic alloys can be utilized to tailor the interface structure in metal matrix composites. Metal matrix composites with monotectic and hypermonotectic Al-In matrices were made by pressure infiltration, remelted and directionally solidified to observe the wetting characteristics of the alloys as well as the effect on structure of solidification in the constrained field of the fiber interstices. Models for monotectic growth are modified to take into account solidification in these constrained fields.

Frier, Nancy L.↗
NASA NTRS1977

The influence of growth speed, orientation and environment on fracture of aligned Al-CuAl2

There has been considerable interest in the mechanical properties of aligned eutectics as functions of microstructure, orientation between reinforcement and stress axis, and temperature of testing. However, little is known about the behavior of these alloys in aggressive environments, such as liquid metals, with the exception of a recent paper on embrittlement of several eutectic alloys in gallium and gallium-indium alloys. This paper is concerned with the effects of a liquid Ga-16%In solution on tensile behavior of an aligned Al-CuAl2 eutectic.

Skiff, P. K.↗
DOE OSTI2023

Stretchable and wearable polymeric heaters and strain sensors fabricated using liquid metals

Wearable electronic devices (WEDs) are receiving significant attention because of the increasing interest in soft robotics, electronic skin, and wearable sensors. Liquid metals (LMs) are compelling for WEDs owing to their metallic conductivity, fluidic nature, and low toxicity. For this study, we fabricated stretchable and soft WEDs using LM (eutectic gallium-indium alloy) wires (LMWs) patterned via force wetting through custom-made stencils on an elastic substrate. LMWs can generate thermal energy via Joule heating upon current application and deliver it to the substrate, resulting in wearable polymeric heaters. The LM mixed with carbonyl iron particles (CIPs) can also be patterned while preserving fluidic behavior. The degree of thermal energy generated through the LMWs can be manipulated as a function of the CIP concentration in the LM and geometrical factors of the electrode patterns, i.e., width and length. An elastic film patterned with LMWs attached to the human body exhibits changes in the effective electrical resistance depending on applied strain, demonstrating potential as a wearable strain sensor. This LM utilized WED that can generate thermal energy upon current application through the LMWs and detect the bodily motion has significant potential for application in wearable thermotherapy, electronic skin, and soft sensors.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Tracking Spatiotemporal Electric Potential in Batteries Using High-Resolution Operando X‑ray Transmission Imaging

The formation of significant concentration gradients across electrolytes in batteries affects the rate at which electrochemical reactions occur. In this work, we use high-resolution operando X-ray transmission imaging to capture spatiotemporal salt concentration profiles c(x,t) in a symmetric cell comprising a polymer electrolyte sandwiched between two lithium–indium alloy electrodes during a constant-current experiment followed by open-circuit relaxation. The decay of open-circuit potential is related to the concentration dependence of the potential across concentration cells, U. We show how operando c(x,t) data can be used to calculate the spatiotemporal electric potential “inside” the polarized electrolyte. We track the spatial- and time-dependent cell potential during the constant-current step and distinguish its two contributions: a concentration overpotential governed by U. and an ohmic contribution governed by ionic conductivity. Over most of the time window, the concentration overpotential dominates. At steady state, it is a factor of 7 larger than the ohmic contribution. Such findings indicate that efforts to design new polymer electrolytes should focus on minimizing concentration gradients.

Electrical conductivity↗
DOE OSTI2025

Amino Acid Sequence Controls Enhanced Electron Transport in Heme-Binding Peptide Monolayers

Metal-binding proteins have the exceptional ability to facilitate long-range electron transport in nature. Despite recent progress, the sequence-structure–function relationships governing electron transport in heme-binding peptides and protein assemblies are not yet fully understood. In this work, the electronic properties of a series of heme-binding peptides inspired by cytochrome bc1 are studied using a combination of molecular electronics experiments, molecular modeling, and simulation. Self-assembled monolayers (SAMs) are prepared using sequence-defined heme-binding peptides capable of forming helical secondary structures. Following monolayer formation, the structural properties and chemical composition of assembled peptides are determined using atomic force microscopy and X-ray photoelectron spectroscopy, and the electronic properties (current density–voltage response) are characterized using a soft contact liquid metal electrode method based on eutectic gallium–indium alloys (EGaIn). Our results show a substantial 1000-fold increase in current density across SAM junctions upon addition of heme compared to identical peptide sequences in the absence of heme, while maintaining a constant junction thickness. These findings show that amino acid composition and sequence directly control enhancements in electron transport in heme-binding peptides. Overall, this study demonstrates the potential of using sequence-defined synthetic peptides inspired by nature as functional bioelectronic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Minimizing Interfacial Resistance between Polymer Electrolytes and Metal Electrodes Using Applied Current

Reducing the interfacial resistance between different phases in electrochemical systems is crucial for enabling practical applications. In this work, we proposed a process for reducing the interfacial resistance between polymer electrolytes and metal electrodes. Thus far in the literature, the lowest interfacial resistance reported in these systems is 15 Ω·cm2. In this study, assembled and preconditioned symmetric cells with lithium–indium alloy electrodes showed similar values. The current through the cell was increased in steps up to the limiting current. This resulted in a permanent decrease of the interfacial resistance to values as low as 1 Ω·cm2, a value that is comparable to that of optimized lithium-ion batteries. The proposed process is general, and it could be applied to any combination of polymer electrolytes and metal electrodes.

Lee, Jaeyong↗
DOE OSTI2020

Defect filtering for thermal expansion induced dislocations in III–V lasers on silicon

Epitaxially integrated III–V semiconductor lasers for silicon photonics have the potential to dramatically transform information networks, but currently, dislocations limit performance and reliability even in defect-tolerant InAs quantum dot (QD)-based lasers. Despite being below the critical thickness, QD layers in these devices contain previously unexplained misfit dislocations, which facilitate non-radiative recombination. We demonstrate here that these misfit dislocations form during post-growth cooldown due to the combined effects of (1) thermal-expansion mismatch between the III–V layers and silicon and (2) mechanical hardening in the active region. By incorporating an additional sub-critical thickness, indium-alloyed “misfit dislocation trapping layer,” we leverage these mechanical hardening effects to our advantage, displacing 95% of misfit dislocations from the QD layer in model structures. Unlike conventional dislocation mitigation strategies, the trapping layer reduces neither the number of threading dislocations nor the number of misfit dislocations. It simply shifts the position of misfit dislocations away from the QD layer, reducing the defects' impact on luminescence. In full lasers, adding a misfit dislocation trapping layer both above and below the QD active region displaces misfit dislocations and substantially improves performance: we measure a twofold reduction in lasing threshold currents and a greater than threefold increase in output power. Overall, our results suggest that devices employing both traditional threading dislocation reduction techniques and optimized misfit dislocation trapping layers may finally lead to fully integrated, commercially viable silicon-based photonic integrated circuits.

36 MATERIALS SCIENCE↗