Search NASA⌕ Search

SEARCH · Search NASA

Results for “InP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Dataset for "Bioaerosols are the dominant source of warm-temperature immersion-mode INPs and drive uncertainties in INP predictability

Ice nucleating particles (INPs) are a rare subset of atmospheric aerosol that can initiate primary ice formation and thus trigger cloud glaciation. The re is a significant gap between our ability to measure INPs and to predict their concentrations and variability in large-scale weather and climate models. Accurate simulation of I NPs requires simulation of their major particle sources, as well as representative parameterizations of IN efficiency. Thus, there is a need for measurements of INP concentrations , delineated by particle type, to validate and improve model prediction of INP concentrations. Here we present a novel method for speciating INP concentrations into the relative c ontributions from dust, sea spray aerosol (SSA), and bioaerosol using single particle measurements. In a field campaign at Bodega Bay (coastal California), we find that bioaerosol s were the primary source of INPs between -12 and -20 ?C, while dust was a relatively minor source and SSA did not contribute significantly. We show that recent INP parameterizati ons for dust and SSA accurately predict ambient INP concentrations for these particle types. Finally, we use the speciated INP concentrations to evaluate the simulation of INPs at Bodega Bay, using a Lagrangian approach to connect the locally-observed aerosol with regionally-widespread emissions parameterizations. We find that we can skillfully simulate du st and SSA INPs, but not bioaerosol INPs. This points to a need for additional research to identify the major factors controlling the emissions and INP efficiency of bioaerosol IN Ps in order to develop improved parameterizations and enable their improved representation in models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

Increased Optoelectronic Quality and Uniformity of Hydrogenated p-InP Thin Films

The thin-film vapor-liquid-solid (TF-VLS) growth technique presents a promising route for high quality, scalable, and cost-effective InP thin films for optoelectronic devices. Toward this goal, careful optimization of material properties and device performance is of utmost interest. Here, we show that exposure of polycrystalline Zn-doped TF-VLS InP to a hydrogen plasma (in the following referred to as hydrogenation) results in improved optoelectronic quality as well as lateral optoelectronic uniformity. A combination of low temperature photoluminescence and transient photocurrent spectroscopy was used to analyze the energy position and relative density of defect states before and after hydrogenation. Notably, hydrogenation reduces the relative intragap defect density by 1 order of magnitude. As a metric to monitor lateral optoelectronic uniformity of polycrystalline TF-VLS InP, photoluminescence and electron beam induced current mapping reveal homogenization of the grain versus grain boundary upon hydrogenation. At the device level, we measured more than 260 TF-VLS InP solar cells before and after hydrogenation to verify the improved optoelectronic properties. Hydrogenation increased the average open-circuit voltage (VOC) of individual TF-VLS InP solar cells by up to 130 mV and reduced the variance in VOC for the analyzed devices.

14 SOLAR ENERGY↗
DOE OSTI2023

Bioaerosols are the dominant source of warm-temperature immersion-mode INPs and drive uncertainties in INP predictability

Ice-nucleating particles (INPs) are rare atmospheric aerosols that initiate primary ice formation, but accurately simulating their concentrations and variability in large-scale climate models remains a challenge. Doing so requires both simulating major particle sources and parameterizing their ice nucleation (IN) efficiency. Validating and improving model predictions of INP concentrations requires measuring their concentrations delineated by particle type. We present a method to speciate INP concentrations into contributions from dust, sea spray aerosol (SSA), and bioaerosol. Field campaign data from Bodega Bay, California, showed that bioaerosols were the primary source of INPs between –12° and –20°C, while dust was a minor source and SSA had little impact. We found that recent parameterizations for dust and SSA accurately predicted ambient INP concentrations. However, the model did not skillfully simulate bioaerosol INPs, suggesting a need for further research to identify major factors controlling their emissions and INP efficiency for improved representation in models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Programmable Phase Selection between Altermagnetic and Noncentrosymmetric Polymorphs of MnTe on InP via Molecular Beam Epitaxy

This dataset contains DFT input and output files supporting the theoretical modeling in the associated publication (ACS Appl. Mater. Interfaces 2026, 18, 15654-15664). The calculations model the interfacial energetics of two MnTe polymorphs — NiAs-MnTe (hexagonal, alpha phase) and ZnS-MnTe (cubic, gamma phase) — on InP(111) substrates with two surface terminations: In-terminated InP(111)A and P-terminated InP(111)B. This gives four interface configurations: NiAs on In-terminated (experimentally observed), NiAs on P-terminated (computed for comparison), ZnS on In-terminated (computed for comparison), and ZnS on P-terminated (experimentally observed). The dataset is organized into four calculation types, each covering all four polymorph/termination combinations: (i) Slabs: Pristine MnTe/InP heterostructure slabs used to compute total energies and interface energy densities (Eint) for all four configurations, as reported in Fig. 6 of the main text. (ii) Disorder: Same slab geometries with a P_Te + Te_P antisite defect pair introduced near the interface, used to assess chemical intermixing effects on interface stability (Fig. S8, SI). (iii) Strain: Pristine slab calculations with in-plane lattice parameters strained by -1% and +1% relative to the InP lattice constant, used to evaluate strain-dependent interface energetics (Fig. S9, SI). (iv) Charge_Density: Single-point calculations on the full heterostructure, the isolated InP slab, and the isolated MnTe slab at fixed geometry, used to compute differential charge density plots showing interfacial charge accumulation and depletion as a function of surface termination (Fig. S10, SI). Each calculation folder contains INCAR, KPOINTS, POSCAR, CONTCAR, OUTCAR, and POTCAR_info.txt (PAW potential information, excluding the full POTCAR due to VASP licensing restrictions). The calculations were performed using VASP 6.4.3 with PBE exchange-correlation, PAW potentials, a Hubbard correction of Ueff = 5 eV on Mn d-states, and A-type AFM spin initialization.

36 MATERIALS SCIENCE↗
NASA NTRS1994

High-efficiency, deep-junction, epitaxial InP solar cells on (100) and (111)B InP substrates

We report on the development and performance of deep-junction (approximately 0.25 micron), graded-emitter-doped, n(sup +)-p InP solar cells grown by metallorganic chemical vapor deposition (MOCVD). A novel, diffusion-transport process for obtaining lightly-doped p-type base regions of the solar cell is described. The I-V data and external quantum-efficiency response of these cells are presented. The best active-area AMO efficiency for these deep-junction cells on (100)-oriented InP substrates is 16.8 percent, with a J(sub SC) of 31.8 mA/sq cm, a V(sub OC) of 0.843 V, and a fill-factor of 0.85. By comparison, the best cell efficiency on the (111)B-oriented InP substrates was 15.0 percent. These efficiency values for deep-junction cells are encouraging and compare favorably with performance of thin-emitter (0.03 micron) epitaxial cells as well as that of deep-emitter diffused cells. The cell performance and breakdown voltage characteristics of a batch of 20 cells on each of the orientations are presented, indicating the superior breakdown voltage properties and other characteristics of InP cells on the (111)B orientation. Spectral response, dark I-V data, and photoluminescence (PL) measurements on the InP cells are presented with an analysis on the variation in J(sub SC) and V(sub OC) of the cells. It is observed, under open-circuit conditions, that lower-V(sub OC) cells exhibit higher band-edge PL intensity for both the (100) and (111)B orientations. This anomalous behavior suggests that radiative recombination in the heavily-doped n(sup +)-InP emitter may be detrimental to achieving higher V(sub OC) in n(sup +)-p InP solar cells.

Venkatasubramanian, R.↗
DOE OSTI2015

Spatially indirect radiative recombination in InAlAsSb grown lattice-matched to InP by molecular beam epitaxy

A photoluminescence (PL) spectroscopy study of the bulk quaternary alloy InAlAsSb is presented. Samples were grown lattice-matched to InP by molecular beam epitaxy and two different growth temperatures of 450 °C and 325 °C were compared. Interpolated bandgap energies suggest that the development of this alloy would extend the range of available direct bandgaps attainable in materials lattice-matched to InP to energies as high as 1.81 eV. However, the peak energy of the observed PL emission is anomalously low for samples grown at both temperatures, with the 450 °C sample showing larger deviation from the expected bandgap. A fit of the integrated PL intensity (I) to an I∝P{sup k} dependence, where P is the incident power density, yields characteristic coefficients k = 1.05 and 1.18 for the 450 °C and 325 °C samples, respectively. This indicates that the PL from both samples is dominated by excitonic recombination. A blue-shift in the peak emission energy as a function of P, along with an S-shaped temperature dependence, is observed. These trends are characteristic of spatially-indirect recombination associated with compositional variations. The energy depth of the confining potential, as derived from the thermal quenching of the photoluminescence, is 0.14 eV for the 325 °C sample, which is consistent with the red-shift of the PL emission peak relative to the expected bandgap energy. This suggests that compositional variation is the primary cause of the anomalously low PL emission peak energy. The higher energy PL emission of the 325 °C sample, relative to the 450 °C sample, is consistent with a reduction of the compositional fluctuations. The lower growth temperature is therefore considered more favorable for further growth optimization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Wide bandgap, strain-balanced quantum well tunnel junctions on InP substrates

In this work, the electrical performance of strain-balanced quantum well tunnel junctions with varying designs is presented. Strain-balanced quantum well tunnel junctions comprising compressively strained InAlAs wells and tensile-strained InAlAs barriers were grown on InP substrates using solid-source molecular beam epitaxy. The use of InAlAs enables InP-based tunnel junction devices to be produced using wide bandgap layers, enabling high electrical performance with low absorption. The impact of well and barrier thickness on the electrical performance was investigated, in addition to the impact of Si and Be doping concentration. Finally, the impact of an InGaAs quantum well at the junction interface is presented, enabling a peak tunnel current density of 47.6 A/cm{sup 2} to be realized.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2013

Carriers mobility of InAs- and InP- rich InAs-InP solid solutions irradiated by fast neutrons

We have studied the low temperature charge carriers mobility in bulk single crystals of InAs- and InP- rich InAs-InP solid solutions irradiated with maximum integral flux 2⋅10{sup 18} n/cm{sup 2} of fast neutrons. Influence of minor component small addition in InAs-InP solid solutions has been revealed. There are also presented data of radiation defects thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1991

High performance etchant for thinning p(+)-InP and its application to p(+)n InP solar cell fabrication

An etchant, namely (o-H3PO4)u: (HNO3)v: (H2O2)t: (H2O)1-(u+v+t) is developed for thinning, after contacting, the p(+) emitter layer of p(+)n InP structures made by thermal diffusion. Varying u, v, and t, reproducible etch rates of 5 to 110 nm/min are obtained. After thinning the 0.6- to 2.5-micron thick p(+) InP layer down to 60-250 nm, specular surfaces are obtained at up to 80 nm/min etch rate. Due to its intrinsic qualities the resisual P-rich oxide after thinning the emitter layer provides surface passivation of p(+) InP surfaces and can also serve as a first-layer AR coating.

Faur, Maria↗
DOE OSTI2017

Low-Temperature epitaxial growth of InGaAs films on InP(100) and InP(411)A substrates

The structural and electrical characteristics of In{sub 0.53}Ga{sub 0.47}As epitaxial films, grown in the low-temperature mode on InP substrates with (100) and (411)A crystallographic orientations at flow ratios of As4 molecules and In and Ga atoms of γ = 29 and 90, have been comprehensively studied. The use of InP(411)A substrates is shown to increase the probability of forming two-dimensional defects (twins, stacking faults, dislocations, and grain boundaries), thus reducing the mobility of free electrons, and As{sub Ga} point defects, which act as donors and increase the free-electron concentration. An increase in γ from 29 to 90 leads to transformation of single-crystal InGaAs films grown on (100) and (411)A substrates into polycrystalline ones.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2012

100 mm Engineered InP-on-Si Laminate Substrates for InP-based Multijunction Solar Cells

The project focused on fabrication of InP/Si laminate substrates as templates for growth of InGaAsP/InGaAs and InAlAs/InGaAsP/InGaAs multijunction solar cells. InP/Si template substrates were developed and used as templates for InGaAs solar growth. A novel feature of the program was development of the virtual substrate template, which enables a substrate to be formed with a lattice constant intermediate between those of GaAs and InP. Large-area virtual substrate templates were formed by transfer and bonding of dislocation free InGaAs films wafer onto silicon substrates.

14 SOLAR ENERGY↗
DOE OSTI2022

Controlling Catalyst–Semiconductor Contacts: Interfacial Charge Separation in p-InP Photocathodes

Charge-carrier-selective interfaces between electrocatalyst particles and semiconductor light absorbers are critical for solar photochemistry but controlling their properties is challenging. Using thin films and nanoparticle arrays of Pt hydrogen-evolution catalysts on p-InP (a high-performance photocathode material), along with macroscopic and nanoscopic electrical and chemical analysis, we show how hydrogen alloying, the pinch-off effect for nanoscale contacts, and the formation of a native surface oxides all play different roles in creating charge-carrier-selective junctions. As a result, the new insights can be broadly applied to photocathodes, photoanodes, and overall water-splitting systems to control charge-carrier selectivity and improve performance.

14 SOLAR ENERGY↗
NASA NTRS1991

A comparative study of performance parameters of n(+)-p InP solar cells made by closed-ampoule sulfur diffusion into Cd- and Zn-doped p-type InP substrates

Preliminary results indicate that Cd-doped substrates are better candidates for achieving high efficiency solar cells fabricated by closed-ampoule sulfur (S) diffusion than Zn-doped substrates. The differences in performance parameters (i.e., 14.3 percent efficiency for Cd-doped vs. 11.83 percent in the case of Zn-doped substrates of comparable doping and etch pit densities) were explained in terms of a large increase in dislocation density as a result of S diffusion in the case of Zn-doped as compared to Cd-doped substrates. The In(x)S(y) and probably Zn(S) precipitates in the case of Zn-doped substrates, produce a dead layer which extends deep below the surface and strongly affects the performance parameters. It should be noted that the cells had an unoptimized single layer antireflective coating of SiO, a grid shadowing of 6.25 percent, and somewhat poor contacts, all contributing to a reduction in efficiency. It is believed that by reducing the external losses and further improvement in cell design, efficiencies approaching 17 percent at 1 AMO, 25 degrees should be possible for cells fabricated on these relatively high defect density Cd-doped substrates. Even higher efficiencies, 18 to 19 percent should be possible by using long-lifetime substrates and further improving front surface passivation. If solar cells fabricated on Cd-doped substrates turn out to have comparable radiation tolerance as those reported in the case of cells fabricated on Zn-doped substrates, then for certain space missions 18 to 19 percent efficient cells made by this method of fabrication would be viable.

Faur, Mircea↗
DOE OSTI2021

Investigations of the stability of etched or platinized p-InP(100) photocathodes for solar-driven hydrogen evolution in acidic or alkaline aqueous electrolytes

Here, the stability of p-InP photocathodes performing the hydrogen-evolution reaction (HER) has been evaluated in contact with either 1.0 M H 2 SO 4 (aq) or 1.0 M KOH(aq), with a focus on identifying corrosion mechanisms. Stability for the solar-driven HER was evaluated using p-InP electrodes that were either etched or coated with an electrodeposited Pt catalyst (p-InP/Pt). Variables such as trace O 2 were systematically controlled during the measurements. Changes in surface characteristics after exposure to electrochemical conditions as well as electrode dissolution processes were monitored using X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS). In either H 2 SO 4 or KOH, etched p-InP photoelectrodes corroded cathodically under illumination, forming metallic In 0 at the electrode surface. In contrast, electrodeposition of Pt kinetically stabilized illuminated p-InP photocathodes in both H 2 SO 4 and KOH by inhibiting the cathodic corrosion pathway. Notably, when held at 0 V vs. the reversible hydrogen electrode (RHE) in 1.0 M H 2 SO 4 (aq), p-InP/Pt exhibited a stable current density (J) of ~–18 mA cm –2 for >285 h under simulated 1 Sun illumination. The long-term current density vs. potential (J–E) behavior at pH 0 and pH 14 of p-InP/Pt photocathodes correlated with changes in the surface chemistry as well as the dissolution of p-InP. In acidic media, the J–E behavior of p-InP/Pt photocathodes remained nearly constant with time, but the surface of a p-InP/Pt electrodes gradually turned P-rich via a slow and continuous leaching of In ions. In alkaline electrolyte, the surface of p-InP/Pt electrodes was passivated by formation of an InO x layer that exhibited negligible dissolution but led to a substantial degradation in the J–E characteristics. Consequently, changes in the catalytic kinetics and surface stoichiometry are both important considerations for determining the corrosion chemistry and the long-term operational stability of InP photoelectrodes.

14 SOLAR ENERGY↗
DOE OSTI2021

Elucidating the Location of Cd 2+ in Post-synthetically Treated InP Quantum Dots Using Dynamic Nuclear Polarization 31 P and 113 Cd Solid-State NMR Spectroscopy

Indium phosphide quantum dots (InP QD) are a promising alternative to traditional QD materials that contain toxic heavy elements such as lead and cadmium. However, InP QD obtained from colloidal synthesis are often plagued by poor photoluminescence quantum yields (PL-QYs). In order to improve the PL-QY of InP QD, a number of post-synthetic treatments have been devised. Recently, it has been shown that InP post-synthetically treated with Lewis acid metal divalent cations (M-InP) exhibit enhanced PL-QY; however, the molecular structure and mechanism behind the improved PL-QY are not fully understood. Here, to determine the surface structure of M-InP QD, dynamic nuclear polarization surface-enhanced nuclear magnetic resonance spectroscopy (DNP SENS) experiments were employed on a series of InP magic size clusters treated with Cd ions, InP QD, cadmium phosphide (Cd 3 P 2 ) QD, and Cd-treated InP QD (Cd–InP QD). With the use of DNP SENS, we were able to obtain the 1D 31 P and 113 Cd NMR spectra, 113 Cd{ 31 P} rotational-echo double-resonance (REDOR) NMR spectra, and 31 P{ 113 Cd} dipolar heteronuclear multiple quantum correlation (D-HMQC) sequence. Changes in the phosphide 31 P chemical shifts after Cd treatment provide indirect evidence that some Cd alloys into the sub-surface regions of the particle. DNP-enhanced 113 Cd solid-state NMR spectra suggest that most Cd ions are coordinated by oxygen atoms from either carboxylate ligands or surface phosphate groups. 113 Cd{ 31 P} REDOR and 31 P{ 113 Cd} D-HMQC experiments confirm that a subset of Cd ions are located on the surface of Cd–InP QD and coordinated with phosphate groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Investigating the Relative Roles of INPs and CCN in a Simulated Thunderstorm Using a New Immersion Freezing Algorithm

Microphysical processes in deep convective clouds are sensitive to the number concentrations of cloud condensation nuclei (CCN) and ice nucleating particles (INPs), but the effects of INPs are less studied. Modeling studies investigating the effects of INPs and/or CCN on deep convection typically retain a volume‐dependent raindrop freezing relation. The resulting neglect of aerosol accumulation in raindrops via drop collisions has likely produced unrealistic storm responses to INPs in past studies. To address this deficiency, a new immersion freezing algorithm was developed and embedded in a bulk microphysics scheme that freezes both cloud drops and raindrops using the same immersion freezing INP (IF‐INP) activity spectrum based on measurements. Multiple idealized simulations of a single case of deep convection observed during the Clouds, Aerosols, and Complex Terrain Interactions (CACTI) field campaign were conducted, with microphysical differences produced by independently altering IF‐INP temperature dependencies and CCN number concentrations from their observed values. Surface precipitation in all simulations resulted almost exclusively from riming graupel that melted upon descending to the surface. Rainfall and cold pools were substantially and systematically weakened with increased CCN due to decreased graupel riming rates but were relatively insensitive to variations in the magnitude and slope of IF‐INP spectra due to compensating depletion of supercooled liquid water. These compensating processes were a consequence of the accumulation of IF‐INPs in raindrops, encouraging caution in studying IF‐INP effects upon thunderstorms using traditional volume‐dependent drop freezing relationships.

CCN↗