SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The objective of this project is to determine the influence of vibration on the composition homogeneity and microstructure of alloy semiconductors solidified with the Vertical Bridgman-Stockbarger (VBS) technique. InSb-GaSb and InSb were directionally solidified in a VBS apparatus with axial vibration of the ampoule.
Organometallic chemical vapor deposition (OM-CVD) growth of InSb and InAs(1-x)Sb(x) has been obtained using triethylindium (TEI), trimethylantimony (TMS), and arsine (AsH3) on (100) GaAs, (100) InSb, and (111)-B InSb substrates. InSb with excellent morphology was achieved on both (100) InSb and (111)-B InSb substrates. The measured electron mobility at 300 K of undoped InSb grown on (100) GaAs semi-insulating substrates was 40,000 sq cm/V-s at a carrier concentration of ND-NA = 2.0 x 10 to the 16th per cu cm. Carrier concentration of ND-NA = 1.2 x 10 to the 15th per cu cm has been measured at 77 K. InAs(1-x)Sb(x) (x = 0.07-0.75) with mirror-like surfaces have been grown on (100) InSb and InAs substrates. This composition range of x between 0.55 and 0.75 (Eg = 0.1 eV) has been successfully achieved for the first time. Solid composition variations as a function of growth temperature and InSb substrate orientations are also discussed.
High-quality electrostatic gating is a fundamental ingredient for successful semiconducting device physics, and a key element of realizing clean quantum transport. Inspired by the widespread improvement of transport quality when two-dimensional van der Waals (vdW) materials are gated exclusively by other vdW materials, we have developed a method for gating non-vdW materials with an all-vdW gate stack, consisting of a hexagonal boron nitride dielectric layer and a few-layer graphite gate electrode. We demonstrate this gating approach on MOVPE-grown InSb nanoribbons (NRs), a novel variant of the InSb nanowire, with a flattened cross-section. In our all-vdW gated NR devices we observe conductance features that are reproducible and have low- to near-zero gate hysteresis. We also report quantized conductance, which persists to lower magnetic fields and longer channel lengths than typical InSb nanowire devices reported to date. Additionally, we observe level splitting that is highly anisotropic in an applied magnetic field, which we attribute to the ribbon cross-section. The performance of our devices is consistent with the reduced disorder expected from the all-vdW gating scheme, and marks the first report of ballistic, few-modes quantum transport in a non-vdW material with an all-vdW gate. Our results establish all-vdW gating as a promising approach for high-quality gating of non-vdW materials for quantum transport, which is in principle applicable generically, beyond InSb systems. In addition, the work showcases the specific potential of all-vdW gate/InSb NR devices for enabling clean quantum devices that may be relevant for spintronics and topological superconductivity studies.
There were two approaches for fabricating indium antimonide (InSb) arrays with CCD readout discussed. The hybrid approach integrated InSb detectors and silicon CCDs in a modular assembly via an advanced interconnection technology. In the monolithic approach, the InSb infrared detectors and the CCD readout were integrated on the same InSb chip. Both approaches utilized intrinsic (band-to-band) photodetection with the attendant advantages over extrinsic detectors. The status of each of these detector readout concepts, with pertinent performance characteristics, was presented.
Use of the droplet emulsion technique has been successful in studying the undercooling and crystallization behavior of Sb, InSb, and an InSb-Sb eutectic alloy. Both droplet size and imposed cooling rate were influential in controlling the extent of liquid undercooling. The droplet surface coating was of significant importance in determining the resultant solidification product structure through its effect on nucleation kinetics. The maximum undercooling for pure Sb was extended from 0.08 to 0.23 T sub m. While simple crushing techniques provided a dramatic increase in droplet undercooling over the bulk material, emulsification treatments both enhanced this undercooling and allowed successful formation of a metastable simple cubic Sb phase. This phase was stable to temperatures approaching the melting point. The simple cubic phase was detected in droplet samples processed using DTA, air and water quenching, and drop tube processing under a helium gas atmosphere. A deviation in the InSb parent ingot composition limited interpretation of the line compound results, however, emulsification techniques extended the undercooling of this material to 0.17 T sub L and provided a stable, protective surface coating for the droplets. Emulsification of the eutectic alloy was effective at producing various levels of undercooling from 0.1 to 0.2 T sub E. Microstructural examination revealed a normal-type eutectic structure in the undercooled droplets indicating that solidification occurred within the coupled zone and that this zone is somewhat symmetric about the eutectic composition.
Photovoltaic indium antimonide (PV InSb) detector technology has matured over the past several years to enable a wide variety of applications to use this high-performance detector material to advantage. The operating conditions for most of the applications to date for back-side illuminated PV InSb arrays have encompassed focal plane temperatures ranging from 40 to approximately 95 K, with the majority in the narrower range between 60 and 80 K. Background flux conditions have ranged from 10 to the 10th power ph/sq cm/sec to 10 to the 16th power ph/sq cm/sec, most typically between 10 to the 12th power and 10 to the 14th power ph/sq cm/sec. Appropriately, the array parameters were optimized for maximum performance over these temperature and background ranges. The key parameters which were peaked in this process were the resistance-area product of the detectors and their quantum efficiency. The Space Infrared Telescope Facility (SIRTF) Infrared Array Camera requirements, however, present very low temperature and background operating conditions, plus the need for very high signal to noise ratios. Preliminary analysis indicates that back-side illuminated PV InSb arrays can be optimized for operation under these conditions, and some performance projections will be presented.
Epitaxial layers of InSb were grown on InP and GaAs substrates by molecular beam epitaxy. The dependence of the epilayer quality on flux ratio, J sub Sb4/J sub In, was studied. Deviation from an optimum value of J sub Sb4/J sub In (approx. 2) during growth led to deterioration in the surface morphology and the electrical and crystalline qualities of the films. Room temperature electron mobilities as high as 70,000 and 53,000 sq cm /V-s were measured in InSb layers grown on InP and GaAs substrates, respectively. Unlike the previous results, the conductivity in these films is n-type even at T = 13 K, and no degradation of the electron mobility due to the high density of dislocations was observed. The measured electron mobilities (and carrier concentrations) at 77 K in InSb layers grown on InP and GaAs substrates are 110,000 sq cm/V-s (3 x 10(15) cm(-3)) and 55,000 sq cm/V-s (4.95 x 10(15) cm(-3)), respectively, suggesting their application to electronic devices at cryogenic temperatures.
The Santa Barbara Research Center has completed a study leading to the development of advanced Indium Antimonide detector arrays for the Space Infrared Telescope Facility (SIRTF) Focal Plane Array Detector (FPAD) Subsystem of the Infrared Array Camera (IRAC) Band 1. The overall goal of the study was to perform design tradeoff studies, analysis and research to develop a Direct Readout Integrated Circuit to be hybridized to an advanced, high performance InSb detector array that would satisfy the technical requirements for Band 1 as specified in the IRAC Instrument Requirements Document (IRD), IRAC-202. The overall goal of the study was divided into both a near-term goal and a far-term goal. The near-term goal identifies current technology available that approaches, and in some cases meets the program technological goals as specified in IRAC-202. The far-term goal identifies technology development required to completely achieve SIRTF program goals. Analyses of potential detector materials indicates that InSb presently meets all Band 1 requirements and is considered to be the baseline approach due to technical maturity. The major issue with regard to photovoltaic detectors such as InSb and HgCdTe is to achieve a reduction in detector capacitance.
Epitaxial layers of InSb were grown on InP and GaAs substrates by molecular beam epitaxy. The dependence of the epilayer quality on flux ratio, J sub Sb4/J sub In, was studied. Deviation from an optimum value of J sub Sb4/J sub In (approx. 2) during growth led to deterioration in the surface morphology and the electrical and crystalline qualities of the films. Room temperature electron mobilities as high as 70,000 and 53,000 sq cm /V-s were measured in InSb layers grown on InP and GaAs substrates, respectively. Unlike the previous results, the conductivity in these films is n-type even at T = 13 K, and no degradation of the electron mobility due to the high density of dislocations was observed. The measured electron mobilities (and carrier concentrations) at 77 K in InSb layers grown on InP and GaAs substrates are 110,000 sq cm/V-s (3 x 10(15) cm(-3)) and 55,000 sq cm/V-s (4.95 x 10(15) cm(-3)), respectively, suggesting their application to electronic devices at cryogenic temperatures.
Abstract Quantum devices based on InSb nanowires (NWs) are a prime candidate system for realizing and exploring topologically-protected quantum states and for electrically-controlled spin-based qubits. The influence of disorder on achieving reliable quantum transport regimes has been studied theoretically, highlighting the importance of optimizing both growth and nanofabrication. In this work, we consider both aspects. We developed InSb NW with thin diameters, as well as a novel gating approach, involving few-layer graphene and atomic layer deposition-grown AlO x . Low-temperature electronic transport measurements of these devices reveal conductance plateaus and Fabry–Pérot interference, evidencing phase-coherent transport in the regime of few quantum modes. The approaches developed in this work could help mitigate the role of material and fabrication-induced disorder in semiconductor-based quantum devices.
We present a first principles study of the electronic and magnetic properties of epitaxial interfaces between the Heusler compounds, Ti 2 MnIn and Ni 2 MnIn, and the III-V semiconductors, InSb and InAs, respectively. We use density functional theory (DFT) with a machine-learned Hubbard U correction determined by Bayesian optimization. Here, we evaluate these interfaces for prospective applications in Majorana-based quantum computing and spintronics. In both interfaces, states from the Heusler penetrate into the gap of the semiconductor, decaying within a few atomic layers. The magnetic interactions at the interface are weak and local in space and energy. Magnetic moments of less than 0.1 µB are induced in the two atomic layers closest to the interface. The induced spin polarization around the Fermi level of the semiconductor decays within a few atomic layers. The decisive factor for the induced spin polarization around the Fermi level of the semiconductor is the spin polarization around the Fermi level in the Heusler, rather than the overall magnetic moment. As a result, the ferrimagnetic narrow-gap semiconductor Ti 2 MnIn induces a more significant spin polarization in the InSb than the ferromagnetic metal Ni 2 MnIn induces in the InAs. This is explained by the position of the transition metal d states in the Heusler with respect to the Fermi level. Based on our results, these interfaces are unlikely to be useful for Majorana devices but could be of interest for spintronics.
α-Sn thin films can exhibit a variety of topologically nontrivial phases. Both studying the transitions between these phases and making use of these phases in eventual applications requires good control over the electronic and structural quality of α-Sn thin films. α-Sn growth on InSb often results in out-diffusion of indium, a p-type dopant. By growing α-Sn via molecular beam epitaxy on the Sb-rich c(4×4) surface reconstruction of InSb(001) rather than the In-rich c(8×2), we demonstrate a route to substantially decrease and minimize this indium incorporation. The reduction in indium concentration allows for the study of the surface and bulk Dirac nodes in α-Sn via angle-resolved photoelectron spectroscopy without the common approaches of bulk doping or surface dosing, simplifying topological phase identification. In this study, the lack of indium incorporation is verified in angle-resolved and angle-integrated ultraviolet photoelectron spectroscopy as well as in clear changes in the Hall response.
The various noise sources that affect InSb detectors (and similar voltaic devices) are discussed and calculated. Methods are given for measuring detector resistance, photon loading, detector and amplifier capacitance, amplifier frequency response, amplifier noise, and quantum efficiency. A photovoltaic InSb detector with increased sensitivity in the 1 to 5.6 mu region is dicussed.
The design and fabrication of the 8585 InSb charge coupled infrared imaging device (CCIRID) chip are reported. The InSb material characteristics are described along with mask and process modifications. Test results for the 2- and 20-element CCIRID's are discussed, including gate oxide characteristics, charge transfer efficiency, optical mode of operation, and development of the surface potential diagram.
The paper demonstrates the detection of infrared radiation and signal readout on a monolithic InSb charge coupled infrared imaging device. The device is a 20-element linear imager with MOS detectors coupled to a four-phase, surface-channel, charge transfer structure. The charge transfer device is p-channel and has planar ion implanted diode structures for zero input and charge readout. Sensitivity measurements on the MOS infrared detectors were determined for the 20-element array. Data are presented on the operational characteristics of the 20-element linear imager under various conditions of electrical and optical inputs in both multiplexed and a time delay and integration (TDI) mode. Plans are discussed for a monolithic InSb 100-element linear imager and a 20 x 16 TDI linear imager.
The reduction of the equivalent noise temperature in liquid-nitrogen-cooled submillimeter-wave mixers by the use of Schottky barriers on InSb instead of GaAs is evaluated by an analytical model that assumes limited local oscillator power and matched impedances. The calculations, executed at 1.0 and 1.8 THz, take plasma resonance and skin effect into account. For single and multiple contacts on homogeneous semiconductor materials of optimum doping, the noise of InSb diodes is smaller than that of GaAs diodes by a factor of 3 to 14. A simplified model is used to predict the performance of epitaxial structures as well as alternative materials.
There has been a continuing evolution toward larger arrays of infrared detectors, and the technology base derived from the Galileo Near Infrared Mapping Spectrometer (NIMS) has been expanded to linear arrays including from 128 to 512 elements. This advance is based on the commercial availability of high-quality InSb photodiodes and 128/256 element FET switch MUX's (multiplexing elements). The present investigation is concerned with an experimental 128-element linear imager using InSb detectors and silicon MUX for readout. Attention is given to detector array electrical characteristics, the detector readout architecture, noise, and special effects.
The absorption coefficient of two high-purity n-InSb samples is measured in the 10-40 per cm range using Fourier transform spectroscopy. The absorption coefficient spectrum is presented for both samples at 4.2 K. It is also shown for the lower resistance sample cooled to 2.2 K and heated by dc bias to elevated electron gas temperatures of 7.5 and 17.9 K. ac Drude theory gives rather poor agreement with experiment at 2.2 and 4.2 K but does much better when the sample electron gas is heated. In contrast, a simple quantum mechanical theory of absorption based on inverse Bremsstrahlung yields promising agreement at the lower temperatures although its applicability is questionable. The non-Drudian absorption is shown to have a favorable effect on the performance of InSb hot-electron bolometers.