Search NASA⌕ Search

SEARCH · Search NASA

Results for “InSb”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Few-mode and anisotropic quantum transport in InSb nanoribbons using an all-van der Waals material-based gate

High-quality electrostatic gating is a fundamental ingredient for successful semiconducting device physics, and a key element of realizing clean quantum transport. Inspired by the widespread improvement of transport quality when two-dimensional van der Waals (vdW) materials are gated exclusively by other vdW materials, we have developed a method for gating non-vdW materials with an all-vdW gate stack, consisting of a hexagonal boron nitride dielectric layer and a few-layer graphite gate electrode. We demonstrate this gating approach on MOVPE-grown InSb nanoribbons (NRs), a novel variant of the InSb nanowire, with a flattened cross-section. In our all-vdW gated NR devices we observe conductance features that are reproducible and have low- to near-zero gate hysteresis. We also report quantized conductance, which persists to lower magnetic fields and longer channel lengths than typical InSb nanowire devices reported to date. Additionally, we observe level splitting that is highly anisotropic in an applied magnetic field, which we attribute to the ribbon cross-section. The performance of our devices is consistent with the reduced disorder expected from the all-vdW gating scheme, and marks the first report of ballistic, few-modes quantum transport in a non-vdW material with an all-vdW gate. Our results establish all-vdW gating as a promising approach for high-quality gating of non-vdW materials for quantum transport, which is in principle applicable generically, beyond InSb systems. In addition, the work showcases the specific potential of all-vdW gate/InSb NR devices for enabling clean quantum devices that may be relevant for spintronics and topological superconductivity studies.

InSb↗
DOE OSTI2024

Diffusive and ballistic transport in thin InSb nanowire devices using a few-layer-graphene-AlO x gate

Abstract Quantum devices based on InSb nanowires (NWs) are a prime candidate system for realizing and exploring topologically-protected quantum states and for electrically-controlled spin-based qubits. The influence of disorder on achieving reliable quantum transport regimes has been studied theoretically, highlighting the importance of optimizing both growth and nanofabrication. In this work, we consider both aspects. We developed InSb NW with thin diameters, as well as a novel gating approach, involving few-layer graphene and atomic layer deposition-grown AlO x . Low-temperature electronic transport measurements of these devices reveal conductance plateaus and Fabry–Pérot interference, evidencing phase-coherent transport in the regime of few quantum modes. The approaches developed in this work could help mitigate the role of material and fabrication-induced disorder in semiconductor-based quantum devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

First principles study of the electronic structure of the Ni 2 MnIn / InAs and Ti 2 MnIn / InSb interfaces

We present a first principles study of the electronic and magnetic properties of epitaxial interfaces between the Heusler compounds, Ti 2 MnIn and Ni 2 MnIn, and the III-V semiconductors, InSb and InAs, respectively. We use density functional theory (DFT) with a machine-learned Hubbard U correction determined by Bayesian optimization. Here, we evaluate these interfaces for prospective applications in Majorana-based quantum computing and spintronics. In both interfaces, states from the Heusler penetrate into the gap of the semiconductor, decaying within a few atomic layers. The magnetic interactions at the interface are weak and local in space and energy. Magnetic moments of less than 0.1 µB are induced in the two atomic layers closest to the interface. The induced spin polarization around the Fermi level of the semiconductor decays within a few atomic layers. The decisive factor for the induced spin polarization around the Fermi level of the semiconductor is the spin polarization around the Fermi level in the Heusler, rather than the overall magnetic moment. As a result, the ferrimagnetic narrow-gap semiconductor Ti 2 MnIn induces a more significant spin polarization in the InSb than the ferromagnetic metal Ni 2 MnIn induces in the InAs. This is explained by the position of the transition metal d states in the Heusler with respect to the Fermi level. Based on our results, these interfaces are unlikely to be useful for Majorana devices but could be of interest for spintronics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Growth and characterization of α-Sn thin films on In- and Sb-rich reconstructions of InSb(001)

α-Sn thin films can exhibit a variety of topologically nontrivial phases. Both studying the transitions between these phases and making use of these phases in eventual applications requires good control over the electronic and structural quality of α-Sn thin films. α-Sn growth on InSb often results in out-diffusion of indium, a p-type dopant. By growing α-Sn via molecular beam epitaxy on the Sb-rich c(4×4) surface reconstruction of InSb(001) rather than the In-rich c(8×2), we demonstrate a route to substantially decrease and minimize this indium incorporation. The reduction in indium concentration allows for the study of the surface and bulk Dirac nodes in α-Sn via angle-resolved photoelectron spectroscopy without the common approaches of bulk doping or surface dosing, simplifying topological phase identification. In this study, the lack of indium incorporation is verified in angle-resolved and angle-integrated ultraviolet photoelectron spectroscopy as well as in clear changes in the Hall response.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Encapsulation of Ba in InSb Framework Introduces Chirality in Clathrate-Like BaIn 4 Sb 4

The discovery of Zintl compounds remains a powerful strategy for identifying materials with tunable electronic and thermal transport properties. During a concerted search for new inorganic clathrates with In–Sb frameworks, we discovered BaIn 4 Sb 4 . The composition of this phase deviates from that expected for a type-I clathrate with tetrahedral coordination of all In and Sb atoms (Ba 8 In 31 Sb 15 ). Instead, in the chiral structure of BaIn 4 Sb 4 (space group P 3 1 21, No. 152), a part of the In atoms have a trigonal planar coordination of 1In + 2Sb, forming Sb 2 –In–In–Sb 2 nonplanar fragments isostructural to diborane(4) B 2 H 4 with D 2 d symmetry. Ba atoms are located inside 16-vertex In 8 Sb 8 polyhedra, which share vertices and edges to form a chiral framework around the 3 1 screw axes. The title compound is electron-balanced, [Ba 2+ ][In 2+ ] 2 [In 3+ ] 2 [Sb3–] 4 , which was confirmed by characterization of the charge and heat transport properties. BaIn 4 Sb 4 exhibits a low thermal conductivity and high Seebeck coefficient, suggesting its untapped potential for thermoelectric applications. Finally, density functional theory (DFT) calculations indicate that chemical doping may enhance carrier concentration and improve the originally low electrical conductivity, thus enhancing thermoelectric performance.

electrical properties↗
DOE OSTI2026

First use of an InSb crystal for x-ray imaging spectroscopy of highly ionized tungsten in the Wendelstein 7-X stellarator

Advances in time and space resolved measurements of highly charged states of tungsten (W) through x-ray imaging spectroscopy have enabled investigation of impurity transport in the Wendelstein 7-X (W7-X) stellarator. The high-resolution x-ray imaging spectrometer (HR-XIS) system on W7-X utilizes the Bragg diffraction properties of a set of multiple crystals to measure a range of impurity emission lines within sections of the 1–7 Å wavelength range, including transitions of W. A new indium–antimonide crystal has been installed on the HR-XIS system to allow viewing of the 5.5–6.2 Å region focusing on emissions of W. Consequently, many bright W emission lines from W 40+ to W 47+ were observed in this wavelength range, both in plasmas with injected W and in those with only intrinsic W impurity sources, showing the high sensitivity of the diagnostic. Three W 46+ emissions correspond in wavelength and intensity with calculated photon emissivity coefficients and can be exploited for W transport and concentration applications in plasmas with T e ≳ 2.1 keV. Here, an estimate of the core W density behavior in two separate turbulence-reduced ‘high-performance’ (HP) discharges on W7-X is done using the 5.6893 Å W 46+ line. The n W behavior in HP scenarios can be explained by previous experimental results and neoclassical predictions.

XICS↗
DOE OSTI2024

Magneto-transport study on Sn-rich Sn 1–x Ge x thin films enabled by CdTe buffer layer

α-Sn, generally known as gray tin, has attracted significant scientific interest due to its potential to host novel topological phases. Studying the transport properties of α-Sn thin films grown on the InSb substrate has been challenging, as the InSb substrate also significantly contributes to the transport properties. In this article, we report a novel approach to epitaxially grow α-Sn thin films on an InSb substrate with a resistive buffer layer of CdTe. Thin films of α–Sn 1–x Ge x (x = 0, 0.025) alloy of 15 nm thickness have been grown using molecular beam epitaxy. The high quality of the samples has been determined through high-resolution x-ray diffraction. The CdTe buffer layer has high resistance and acts as an insulating virtual substrate, which significantly suppresses contribution from InSb. Magnetotransport measurements show clear Shubnikov–de Hass oscillations in α–Sn 1–x Ge x (x = 0, 0.025) thin films. A change in oscillation frequency is observed upon alloying with Ge, implying a modification in the electronic structure and demonstrating the effectiveness of the CdTe buffer layer approach. Furthermore, this work provides a new approach that enables the electronic transport characterization of the α–Sn 1–x Ge x alloy system, which enables the study of the topological quantum states using electronic transport and their device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermal scanning probe and laser lithography for patterning nanowire based quantum devices

Semiconductor nanowire (NW) quantum devices offer a promising path for the pursuit and investigation of topologically-protected quantum states, and superconducting and spin-based qubits that can be controlled using electric fields. Theoretical investigations into the impact of disorder on the attainment of dependable topological states in semiconducting nanowires with large spin–orbit coupling and g-factor highlight the critical need for improvements in both growth processes and nanofabrication techniques. In this work, we used a hybrid lithography tool for both the high-resolution thermal scanning probe lithography and high-throughput direct laser writing of quantum devices based on thin InSb nanowires with contact spacing of 200 nm. Electrical characterization demonstrates quasi-ballistic transport. The methodology outlined in this study has the potential to reduce the impact of disorder caused by fabrication processes in quantum devices based on 1D semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Monocrystalline CdSeTe/MgCdTe Double‐Heterostructure Solar Cells

This article reports monocrystalline CdSeTe/MgCdTe double‐heterostructure (DH) solar cells with varying Se compositions in the absorber layers that are grown on InSb substrates by using molecular beam epitaxy. The Se composition in the samples studied is determined to be 4%–11% through high‐resolution X‐ray diffraction (XRD) and photoluminescence measurements. Increased Se incorporation induces higher defect density attributed to increased lattice mismatch, and mixed‐phase formation due to the small difference in formation energies between the wurtzite and zinc blende phases of CdSe, which causes stacking faults and grain boundaries. Devices are fabricated by directly depositing an n‐type indium tin oxide (ITO) layer on the CdSeTe/MgCdTe DHs followed by Ag metal contacts. Reduced bandgap is observed in solar cells with increased Se composition. The devices with an absorber containing 4% Se exhibit an average open‐circuit voltage ( V OC ) of 0.925 V, a short‐circuit current density ( J SC ) of 23.4 mA/cm 2 , a fill factor ( FF ) of 0.650 and an efficiency of 14.1% without anti‐reflection coating. Absorbers with higher Se compositions result in poor device performance, mainly attributed to high defect density in the materials.

Ju, Zheng [Center for Photonics Innovation Arizona↗
DOE OSTI2026

Slow-Light Mid-IR Silicon Photonic Chips for NO 2 and CH 4 Gas Detection

A compact, chip-scale mid-infrared gas sensor is demonstrated, leveraging a two-dimensional photonic crystal waveguide (PCW) fabricated on a silicon-on-insulator (SOI) platform. The PCW comprises a hexagonal lattice with lattice constant a = 860 nm and hole radius r = 0.22a, incorporating a central line defect of reduced-radius holes (r s = 0.7r) to induce slow-light propagation near the photonic band edge with a group index of approximately 73, thereby enhancing light-matter interaction. The sensor operates at fundamental absorption wavelengths of 3.42 μm for nitrogen dioxide (NO 2 ) and 3.40 μm for methane (CH 4 ), utilizing the strongest molecular vibrational transitions for maximum sensitivity. Experimental validation was conducted using dynamically diluted gas mixtures generated by mass flow controllers, with signal acquisition performed by a liquid nitrogen-cooled InSb detector. For NO 2 , the sensor exhibited excellent linear response over 5–25 ppm (part per million) with coefficient of determination R 2 = 0.9934, achieving a detection limit of 210 ppb (part per billion)─representing the first reported silicon photonic-based NO 2 detection. For CH 4 , exposure to 25 ppm resulted in a 6.4% decrease in transmitted intensity, demonstrating multigas sensing capability. The CMOS-compatible fabrication process and compact 3 mm device footprint establish this SOI-PCW platform as a scalable, low-power solution for integrated mid-infrared gas sensing, with significant potential for environmental monitoring and industrial safety applications.

Crystals↗
DOE OSTI2022

Giant g-factors and fully spin-polarized states in metamorphic short-period InAsSb/InSb superlattices

Abstract Realizing a large Landé g -factor of electrons in solid-state materials has long been thought of as a rewarding task as it can trigger abundant immediate applications in spintronics and quantum computing. Here, by using metamorphic InAsSb/InSb superlattices (SLs), we demonstrate an unprecedented high value of g ≈ 104, twice larger than that in bulk InSb, and fully spin-polarized states at low magnetic fields. In addition, we show that the g -factor can be tuned on demand from 20 to 110 via varying the SL period. The key ingredients of such a wide tunability are the wavefunction mixing and overlap between the electron and hole states, which have drawn little attention in prior studies. Our work not only establishes metamorphic InAsSb/InSb as a promising and competitive material platform for future quantum devices but also provides a new route toward g -factor engineering in semiconductor structures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

g-factor engineering with InAsSb alloys toward zero band gap limit

Band gap is known as an effective parameter for tuning the Landé g factor in semiconductors and can be manipulated in a wide range through the bowing effect in ternary alloys. In this work, using the recently developed virtual substrate technique, high-quality InAsSb alloys throughout the whole Sb composition range are fabricated and a large g factor of g≈-90 at the minimum band gap of ~0.1 eV, which is almost twice that in bulk InSb, is found. Further analysis to the zero gap limit reveals a possible gigantic g factor of g≈-200 with a peculiar relativistic Zeeman effect that disperses as the square root of magnetic field. Such a g-factor enhancement toward the narrow gap limit cannot be quantitatively described by the conventional Roth formula, as the orbital interaction effect between the nearly triply degenerated bands becomes the dominant source for the Zeeman splitting. These results may provide insights into realizing large g factors and spin-polarized states in semiconductors and topological materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Controlling structural phases of Sn through lattice engineering

Topology and superconductivity, two distinct phenomena, offer unique insight into quantum properties and their applications in quantum technologies, spintronics, and sustainable energy technologies. Tin (Sn) plays a pivotal role here as an element because of its two structural phases, α-Sn exhibiting topological characteristics and β-Sn showing superconductivity. Here, we demonstrate precise control of these phases in Sn thin films using molecular beam epitaxy with systematically varied lattice parameters of the buffer layer. The Sn films exhibit either β-Sn or α-Sn phases as the buffer layer's lattice constant varies from 6.10 Å to 6.48 Å, spanning the range from GaSb (like InAs) to InSb. Further, the crystal structures of α- and β-Sn films are characterized by x-ray diffraction and confirmed by Raman spectroscopy and scanning transmission electron microscopy. Atomic force microscopy validates the smooth, continuous surface morphology. Electrical transport measurements further verify the phases: resistance drop near 3.7 K for β-Sn superconductivity and Shubnikov-de Haas oscillations for α-Sn topological characteristics. Density functional theory shows that α-Sn is stable under tensile strain and β-Sn under compressive strain, aligning well with experimental findings. Hence, this study introduces a platform controlling Sn phases through lattice engineering, enabling innovative applications in quantum technologies and beyond.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Structural inversion asymmetry in epitaxial ultrathin films of Bi(111)/InSb(111)B

Bismuth (Bi) films hold potential for spintronic devices due to strong spin-orbit coupling. Understanding the growth, surface states, and interactions with the substrate is key to their functionalization. Large-area high-quality (111) Bi ultrathin films were grown on InSb (111)B substrates by molecular beam epitaxy (MBE). Strong film-substrate interactions epitaxially stabilize the (111) orientation and lead to nonequivalent interface potentials. Analysis of angle-resolved photoemission spectroscopy (ARPES) measurements, employed to characterize the evolution of the surface states with film thickness, indicate a crossing at the $\overline{M}$ point, suggesting a topologically trivial phase in the thin film. In conclusion, the results show the presence of interfacial bonds to the substrate breaks inversion symmetry, preventing the semimetal-to-semiconductor transition predicted for freestanding bismuth layers, highlighting the importance of controlled functionalization and surface passivation of two-dimensional materials.

Inbar, Hadass S. [Univ. of California, Santa Barba↗
DOE OSTI2025

Evolution of surface morphology from Stranski–Krastanov growth mode to step-flow growth mode in InSbBi thin films

The incorporation of dilute concentrations of bismuth (Bi) into traditional III–V alloys leads to a significant reduction in bandgap energy, making InSbBi a promising candidate for long-wavelength (<0.17 eV) infrared photosensors. InSbBi offers potential as a platform for exploring spin dynamics and quantum phenomena due to its strong spin–orbit coupling. Despite this promise, the material quality of InSbBi alloys remains inferior to that of conventional III–V semiconductors, primarily due to the substantial challenges associated with incorporating Bi into InSb and producing high-quality InSbBi with varying Bi compositions. In this study, we address these issues by developing a molecular beam epitaxy approach to grow smooth InSbBi thin films with tunable Bi incorporation up to 1.8% of the group V sublattice, through dynamic adjustment of Sb flux and careful control of the interplay between growth temperature and the Bi flux. In conclusion, this work paves way for the development of high-quality InSbBi thin films for applications in photodetection, spintronics, and related quantum technologies.

Edirisinghe, Chandima Kasun [Univ. of Tennessee, K↗
DOE OSTI2026

From binary to quinary: The rationale and development of GaInAsSbBi for mid- and long-wave infrared sensing applications

Given the added complexity in flux calibration and composition evaluation inherent to quinary alloy growth, what motivates compounding the challenges of III–V-Bi growth with the goal of producing a quinary alloy of GaInAsSbBi for mid- and long-wave infrared sensing applications? Each elemental constituent provides some additional design freedom to achieve the ultimate goal of producing a lattice-matched, bulk random alloy mid-wave infrared III–V material with smooth surface morphology and high optoelectronic quality to enable high performance elevated operating temperatures. Here, this paper reviews the evolution of Bi-containing semiconductor research, focusing on mid- and long-wave infrared materials and highlighting key research findings that motivated the decisions to accept the added complexity in going from binaries like InAs or InSb, to InAsBi, to InAsSbBi, and, finally, to GaInAsSbBi to meet the performance demands of advanced infrared sensing applications.

Webster, Preston T. [Air Force Research Laboratory↗
DOE OSTI2023

Synthesis and Observation of Emergent Phenomena in Epitaxial Heusler Compound Heterostructures

The proposal was on the synthesis and observation of emergent phenomena in epitaxial Heusler compound heterostructures. The large range of properties and number of Heusler compounds opens up a wide number of potential compounds that will exhibit emergent phenomena. The similarity, large range of relatively inexpensive, large area, high crystal quality, III-V bulk substrates, lattice parameters and the ability to tune the lattice parameters through ternary or quaternary III-V compound semiconductor epitaxial growth, makes III-V semiconductors an ideal choice for substrates for epitaxial growth of Heusler compounds. A number of half Heusler compounds have been predicted to exhibit band inversion, making them topological and are therefore expected to exhibit spin-momentum locked topological surface states with linear dispersion. Others are predicted to be semimetals with Weyl points and others semiconducting and magnetic. During the course of this grant, emphasis has been on investigating Heusler compounds with emergent phenomena and demonstrating the ability to tune their properties through alloying and strain. We have grown toplogical semimetal (PtLuSb, PtMnBi), Weyl (Co 2 MnAl, Co 2 TiGe), half metal (PtMnSb, Co 2 MnSi, Co 2 MnAl x Si 1-x , Co2FeAl), and semiconducting (CoTiSb, NiTiSn) and tuned their properties through alloying and epitaxial strain. We also investigated the closely related materials of rare-earth monopnictide, some of which have also been predicted to be topological. During the attempts to grow the PtMnBi, it was discovered that Bi, another predicted topological material when ultrathin, could be grown epitaxially on InSb, results for which are also reported here. The main focus for this effort has been on using variable photon energy and spin-dependent angle resolved photoemission (ARPES) to determine bulk band structure and surface states of pristine epitaxial films grown on III-V semiconductor and MgO substrates and correlate results with theory and transport measurements. Theory has been critical to interpretation of experimental results and has been essential in guiding experiments. The research benefited from several strong collaborations between the PIs and the beamline scientists at the Advanced Light Source at Lawrence Berkeley Laboratory, the Stanford Linear Accelerator Center (SLAC) at Stanford and at the Max Lab at Lund University in Sweden. The strong experiment - theory collaboration between the PI’s groups, the Palmstrøm group at UCSB and the Janotti group at the University of Delaware, has been critical for interpreting the experimental ARPES and magnetotransport measurements results and making predictions to guide experiments. Weekly interactive Zoom meetings made this work well. A collaboration between the Palmstrøm group and Dr. Alexei Fedorov at the Advanced Light Source (ALS) resulted in significant modifications to his end chamber to accommodate the vacuum suitcase that was designed and constructed in the Palmstrøm group at UCSB. In collaboration with beamline scientists, Drs. Makoto Hashimoto and Donghui Lu at SLAC, Palmstrøm made modifications to the vacuum suitcase and developed special sample holders that allowed samples to be grown in the Palmstrøm MBE systems at UCSB and transported in the UHV vacuum suitcase to SLAC for ARPES measurements. The development of the vacuum suitcase was essential for this grant as it has allowed variable photon energies to be used to identify surface versus bulk states on samples that could not be capped and decapped using As- or Sb-capping layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗