Search NASA⌕ Search

SEARCH · Search NASA

Results for “Industrial CO 2 streams”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Pulsed Electrolysis Promotes Catalyst Activity in Dilute CO 2 Streams

Industrial CO 2 streams vary widely in composition, from pure to as low as 3%, posing challenges for purification or direct conversion. Electrochemical reduction offers a route for converting dilute CO 2 streams but faces severe mass transport limitations. This study demonstrates that pulsed electrolysis effectively overcomes these limitations, enhancing CO 2 electroreduction across variable feed compositions and current densities, particularly at low CO 2 concentrations and high current densities. At 25% CO 2 and 400 mA cm −2 , pulsing improved selectivity from 25.6 to 78.6%, production rate from 13.7 to 21.0 mol m −2 h −1 , and energy productivity from 0.77 to 2.59 mol kWh −1 . A dynamic, multiphysics continuum model confirms a 64% increase in CO 2 concentration within the catalyst layer during pulsing, resolving the transient chemical microenvironment. These findings establish pulsed electrolysis as a viable strategy for converting dilute industrial CO 2 streams into valuable feedstocks, bypassing costly pre-separation.

Orfali, Dania Muhieddine [New York University (NYU↗
DOE OSTI2022

Achieving superior carbon transfer efficiency and pH control using membrane carbonation with a wide range of CO 2 contents for the coccolithophore Emiliania huxleyi

The economic viability of microalgal-derived products relies on rapid CO 2 transfer in a cost-effective manner. Many industrial gas streams contain concentrated CO 2 that, if converted to useful products, would lower greenhouse gas emissions and valorize the wasted CO 2 . Membrane carbonation (MC) uses non-porous hollow-fiber gas-transfer membranes to deliver CO 2 without bubble formation, which makes it possible to achieve a high carbon-transfer efficiency (CTE). However, inert gasses in the industrial streams (e.g., N 2 , O 2 , and H 2 O) can significantly lower the CO 2 -delivery rate. The means to overcome the buildup of inert gases in the membrane lumen is to manage the distal end of the membranes to sweep out inert gases while not wasting significant CO 2 . A MC-venting strategy was evaluated for CO 2 inputs from 5% to 100%. Abiotic tests using a restricted exit flow could achieve >95% CTE abiotic for industrial CO 2 streams. When integrated with semi-continuous cultivation of a marine coccolithophore, Emiliania huxleyi , CO 2 delivery and venting were on-demand based on a pH set points and pH-actuated feed and venting valves. MC using the venting strategy achieved 100% CTE biotic when delivering 100% and 50% CO 2 , which was better than 50% CTE biotic obtained from pH-controlled sparging of 100% CO 2 -sparging. E. huxleyi consistently fixed ~80% of the delivered CO 2 into biomass, and the remaining ~20% to calcite coccoliths. Finally, the compact size of MC modules, stable pH control, and no shear forces from bubble agitation during the CO 2 delivery made MC an ideal match for cultivation of coccolithophores, which are sensitive to shear forces and pH fluctuations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Enhanced carbon-transfer and -utilization efficiencies achieved using membrane carbonation with gas sources having a range of CO 2 concentrations

The economic viability of microalgal biofuels relies on increasing productivity in a cost-effective manner. As microalgal biomass contains > 50% carbon, a high rate of CO 2 delivery is required for high productivity, and inefficient CO 2 delivery amplifies operating costs. Membrane carbonation using non-porous hollow fiber membranes can ideally deliver CO 2 without bubble formation and high carbon transfer efficiency. Because CO 2 streams from industrial resources are not 100% CO 2 , the buildup of inert gasses can significantly lower the CO 2 delivery rate when the distal end of the membrane is closed. To overcome the buildup of inert gases, we managed the distal end of the membranes with three different approaches: fully open end, restricted bleed valve, and restricted bleed valve with pH-actuated venting. For all approaches, CO 2 was delivered to membranes ondemand based on a pH set point. Evaluating a wide range of CO 2 concentrations (10% to 100%), we found that all approaches eliminated the buildup of inert gases, could maintain target pH values and gave the same biomass productivities and carbon distributions. However, carbon transfer efficiency depended on the operation of the distal end. Fully open-end operation gave a poor carbon transfer efficiency because of excessive loss of CO 2 from the distal end. However, restricting the exit flow rate to ≤4 cm 3 /min mitigated the problems of excessive CO 2 loss, but without incurring a large loss of CO 2 -delivery flux. For the continuous cultivation, combining a restricted bleed valve with pH-actuated venting improved the carbon-transfer efficiency and -utilization efficiencies up to 85% and 67%, respectively, with a sufficient CO 2 delivery flux.

42 ENGINEERING↗
DOE OSTI2024

Ion Exchange Processes for CO 2 Mineralization Using Industrial Waste Streams: Pilot Plant Demonstration and Life Cycle Assessment

Abstract An attractive technique for removing CO 2 from the environment is sequestration within stable carbonate solids (e. g., calcite). However, continuous addition of alkalinity is required to achieve favorable conditions for carbonate precipitation (pH>8) from aqueous streams containing dissolved CO 2 (pH<4.5) and Ca 2+ ions. In this study, a pH‐swing process using ion exchange was demonstrated to process 300 L of produced water brine per day for CO 2 mineralization. Proton titration capacities were quantified for aqueous streams in equilibrium with gas streams at various concentrations of CO 2 (pCO 2 =0.03–0.20 atm) and at various flow rates (0.5–2.0 L min −1 ). Energy intensities for the process were determined to be between 30 and 65 kWh per tonne of CO 2 sequestered depending on the composition of the brine stream. A life cycle assessment was performed to analyze the net carbon emissions of the technology which indicated a net CO 2 reduction for pCO 2 ≥0.12 atm (−0.06–−0.39 kg CO 2 e per kg precipitated CaCO 3 ) utilizing calcium‐rich brines. The results from this study indicate the ion exchange process can be used as a scalable method to provide alkalinity necessary for the capture and storage of CO 2 in Ca‐rich waste streams.

Chemistry↗
DOE OSTI2024

Achieving Unprecedented CO 2 Utilization InCO 2 Concrete™: System Design, Product Development and Process Demonstration

Anthropogenic sources of carbon dioxide are generated from a number of sources, but the key among these are ordinary Portland cement (OPC) production and combustion of fossil fuels. Cement production is the largest global CO 2 source from the mineral decomposition of carbonates. This is due to the clinkering process whereby limestone (mainly consisting of CaCO 3 ) is decomposed into CaO and CO 2 , and combined with silica rich clays at high temperatures to form clinkers (i.e. the four key minerals that comprise cement). The high temperature range of 1400 – 1550°C required for this process accounts for up to 60% of the generated CO 2 from cement production. Combination of the limestone decomposition and thermal requirements of the clinkering process causes cement production to contribute 8-9% of annual global CO 2 emissions. Combustion of fossil fuels (coal, oil and gas) was shown to contribute a much larger portion of global CO 2 emissions. As of 2018, combustion of fossil fuels accounted for 65% of global CO 2 , where 41% was derived from stationary sources for electricity and heat generation and the other 24% was related to transport. To reduce these contributions, key steps forward in CO 2 utilization technologies are required. Therefore, a CO 2 mineralization technology (CO 2 mineralization concrete) to reduce the OPC content in concrete, while utilizing flue gas emissions from fossil fuel combustion has been developed to address both areas simultaneously. This Reversa™ technology utilizes low-carbon cementation agents produced by in situ CO 2 mineralization (“mineral carbonation reactions”) to offer a promising alternative to OPC. CO 2 mineralization relies upon the reaction of dissolved CO 2 with inorganic alkaline reactants to precipitate mineral carbonates (e.g., CaCO 3 ), which bind proximate particles and achieve cementation. Herein, a concrete green body, which is composed of a mixture of binder, water, and mineral aggregates, is exposed to CO 2 borne in industrial flue gas streams. This manner of CO 2 mineralization allows the production of construction components that feature equivalent engineering attributes as their OPC-based counterparts while featuring a much smaller embodied carbon intensity (eCI). The purpose of this project is to demonstrate the feasibility of the Reversa process evolving from a TRL-3 technology at the bench-scale up to TRL-6 technology at the pilot-scale. The reliability of the Reversa technology was tested to prove the effective production of three standard industrial concrete products selected during the course of the project. The results detailed herein will demonstrate the evolution of this technology to the industrial scale. The culmination of this work resulted in 9 production runs completed at the National Carbon Capture Center (NCCC), Wilsonville, AL, using natural gas (NG) flue gas as the CO 2 source. Over the course of the production runs at NCCC, the CO 2 utilization as a function of time, 24-h CO 2 uptake, electricity usage, and 28-d net area compressive strength recorded for each run. Collection of this data will be used to determine the success of the demonstration goals: (1) achieving in excess of 0.2gCO 2 /g reactant , (2) achieving greater than 50% reduction in global warming potential compared to standard produced units, and (3) ensuring compliance of carbonated concrete with industry standard specifications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Strategies to overcome mass transfer limitations of hydrogen during anaerobic gaseous fermentations: A comprehensive review

Fermentation of gaseous substrates such as carbon dioxide (CO 2 ) has emerged as a sustainable approach for transforming greenhouse gas emissions into renewable fuels and biochemicals. CO 2 fermentations are catalyzed by hydrogenotrophic methanogens and homoacetogens, these anaerobic microorganisms selectively reduce CO 2 using hydrogen (H 2 ) as electron donor. However, H 2 possesses low solubility in liquid media leading to slow mass transport, limiting the reaction rates of CO 2 reduction. Solving the problems of mass transport of H 2 could boost the advance of technologies for valorizing industrial CO 2 -rich streams, like biogas or syngas. The application could further be extended to combustion flue gases or even atmospheric CO 2 . In this work, an overview of strategies for overcoming H 2 mass transport limitations during methanogenic and acetogenic fermentation of H 2 and CO 2 is presented. Here, the potential for using these strategies in future full-scale facilities and the knowledge gaps for these applications are discussed in detail.

09 BIOMASS FUELS↗
DOE OSTI2020

Effect of Computational Schemes on Coupled Flow and Geo-Mechanical Modeling of CO 2 Leakage through a Compromised Well

Carbon capture, utilization, and storage (CCUS) describes a set of technically viable processes to separate carbon dioxide (CO 2 ) from industrial byproduct streams and inject it into deep geologic formations for long-term storage. Legacy wells located within the spatial domain of new injection and production activities represent potential pathways for fluids (i.e., CO 2 and aqueous phase) to leak through compromised components (e.g., through fractures or micro-annulus pathways). The finite element (FE) method is a well-established numerical approach to simulate the coupling between multi-phase fluid flow and solid phase deformation interactions that occur in a compromised well system. We assumed the spatial domain consists of a three-phases system: a solid, liquid, and gas phase. For flow in the two fluids phases, we considered two sets of primary variables: the first considering capillary pressure and gas pressure (PP) scheme, and the second considering liquid pressure and gas saturation (PS) scheme. Fluid phases were coupled with the solid phase using the full coupling (i.e., monolithic coupling) and iterative coupling (i.e., sequential coupling) approaches. The challenge of achieving numerical stability in the coupled formulation in heterogeneous media was addressed using the mass lumping and the upwinding techniques. Numerical results were compared with three benchmark problems to assess the performance of coupled FE solutions: 1D Terzaghi’s consolidation, Liakopoulos experiments, and the Kueper and Frind experiments. We found good agreement between our results and the three benchmark problems. For the Kueper and Frind test, the PP scheme successfully captured the observed experimental response of the non-aqueous phase infiltration, in contrast to the PS scheme. These exercises demonstrate the importance of fluid phase primary variable selection for heterogeneous porous media. We then applied the developed model to the hypothetical case of leakage along a compromised well representing a heterogeneous media. Considering the mass lumping and the upwinding techniques, both the monotonic and the sequential coupling provided identical results, but mass lumping was needed to avoid numerical instabilities in the sequential coupling. Additionally, in the monolithic coupling, the magnitude of primary variables in the coupled solution without mass lumping and the upwinding is higher, which is essential for the risk-based analyses.

deformation flow↗
DOE OSTI2020

Implementation of Ion Exchange Processes for Carbon Dioxide Mineralization Using Industrial Waste Streams

Sequestration of CO 2 within stable mineral carbonates (e.g., CaCO 3 ) represents an attractive emission reduction strategy because it offers a leakage-free alternative to geological storage of CO 2 in an environmentally benign form. However, the pH of aqueous streams equilibrated with gaseous streams containing CO 2 (pH < 4) are typically lower than that which is required for carbonate precipitation (pH > 8). Traditionally, alkalinity is provided by a stoichiometric reagent (e.g., NaOH) which renders these processes environmentally hazardous and economically unfeasible. This work investigates the use of regenerable ion-exchange materials to induce alkalinity in CO 2 -saturated aqueous solutions such that the pH shift required for mineralization occurs without the need for stoichiometric reagents. Na + -H + exchange isotherms (at [H + ] = 10 −8 –10 −1 M) and rates were measured for 13X and 4A zeolites and TP-207 and TP-260 organic exchange resins in batch equilibrium and fixed-bed exchange experiments, respectively. At solutions equilibrated with CO 2 at 1.0 atm (pH = 3.9), H + exchange capacities for the materials were similar (1.7–2.4 mmol H + /g material) and resulted in pH increases from 3.9 to greater than 8.0. Multi-component mixtures using Ca 2+ and Mg 2+ cations (at 10 −3 –10 −1 M) in CO 2 -saturated water were used to probe competitive ion exchange. The presence of divalent cations in solution inhibited H + exchange, reducing capacities to as low as 0.2 mmol H + /g for both resins and zeolites. Dynamic H + exchange capacities in fixed-bed ion exchange columns were similar to equilibrium values for resins (∼1.5 mmol/g) and zeolites (∼0.8 mmol/g) using inlet solutions that were equilibrated with gaseous streams of CO 2 at 1.0 atm. However, exchange kinetics were limited by intraparticle diffusion as indicated by the increased rate parameters with increasing inlet flow rates (20–160 cm 3 min −1 ). Experimental calcite precipitation from mixing the alkaline CO 3 2− -rich water solution obtained from the ion-exchange column with a simulated liquid waste stream solution achieved thermodynamic maximum yields. The results from these studies indicate that ion exchange processes can be used as an alternative to the addition of stoichiometric bases to induce alkalinity for the precipitation of CaCO 3 , thereby opening a pathway toward sustainable and economic mineralization processes.

42 ENGINEERING↗
DOE OSTI2021

The role of gas flow distributions on CO 2 mineralization within monolithic cemented composites: coupled CFD-factorial design approach

The carbonation kinetics of monolithic cementing composites are strongly affected by gas transport which is, in turn, influenced by microstructural resistances and the presence of liquid water within pore networks. The non-uniform gas flow distribution within the CO 2 mineralization reactor can impart mass transfer resistance in the monolith microstructure, which affects the uptake of CO 2 (“carbonation”) of the cementing composites. This paper demonstrates how the gas spatial distribution (velocity and flow rate; quantified by CFD analysis) and processing conditions (temperature, relative humidity, and flow rate; quantified by factorial design) affect drying and carbonation, and in turn, the engineering properties of a representative ‘monolithic’ carbonate-cemented concrete component (i.e., herein concrete masonry unit: CMUs, also known as concrete block). It is shown that the gas flow distribution affects drying front penetration and results in moisture and carbonation gradients within the monolith. Particularly, variations in drying kinetics caused by non-uniformity of the contacting gas velocity impose gradients in moisture saturation, which results in increasing microstructural resistance to CO 2 transport. The resultant non-uniform carbonate-mineral formation (i.e., carbonate cementation), if not controlled, can produce gradients in mechanical properties and may alter failure patterns upon loading. Finally, these insights inform the optimal design of gas flow distribution systems and processing conditions within CO 2 mineralization reactors for the manufacturing of low-CO 2 concrete components using CO 2 -dilute industrial flue gas streams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High-temperature carbon dioxide capture in a porous material with terminal zinc hydride sites

Carbon capture can mitigate point-source carbon dioxide (CO 2 ) emissions, but hurdles remain that impede the widespread adoption of amine-based technologies. Capturing CO 2 at temperatures closer to those of many industrial exhaust streams (>200°C) is of interest, although metal oxide absorbents that operate at these temperatures typically exhibit sluggish CO 2 absorption kinetics and instability to cycling. Here, in this study, we report a porous metal–organic framework featuring terminal zinc hydride sites that reversibly bind CO 2 at temperatures above 200°C—conditions that are unprecedented for intrinsically porous materials. Gas adsorption, structural, spectroscopic, and computational analyses elucidate the rapid, reversible nature of this transformation. Extended cycling and breakthrough analyses reveal that the material is capable of deep carbon capture at low CO 2 concentrations and high temperatures relevant to postcombustion capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Summary of Carbon Dioxide Pipeline Systems and Incident Data in North America

Pipelines are historically seen as the primary transportation mode for carbon dioxide (CO 2 ) streams in the context of carbon capture and storage (CCS) and oil and gas industries. Pipeline transmission of CO 2 over longer distances is regarded as most efficient and economical when the CO 2 is in the dense phase, i.e., in liquid or supercritical regime, due to transporting CO 2 in dense phase that allows for a smaller-diameter pipeline to move a given flow, which optimizes project cost.

42 ENGINEERING↗
DOE OSTI2021

Synthetic Methanol/Fischer–Tropsch Fuel Production Capacity, Cost, and Carbon Intensity Utilizing CO 2 from Industrial and Power Plants in the United States

Captured CO 2 is a potential feedstock to produce fuel/chemicals using renewable electricity as the energy source. In this study, we explored resource availability and synergies by region in the United States and conducted cost and environmental analysis to identify unique opportunities in each region to inform possible regional and national actions for carbon capture and utilization development. This study estimated production cost of synthetic methanol and Fischer–Tropsch (FT) fuels by using CO 2 captured from the waste streams emitted from six industrial [ethanol, ammonia, natural gas (NG) processing, hydrogen, cement, and iron/steel production plants] and two power generation (coal and NG) processes across the United States. The results showed that a total of 1594 million metric ton per year of waste CO 2 can be captured and converted into 85 and 319 billion gallons of FT fuels and methanol, respectively. FT fuels can potentially substitute for 36% of the total petroleum fuels used in the transportation sector in 2018. Technoeconomic analysis shows that the minimum selling prices for synthetic FT fuels and methanol are 1.8–2.8 times the price of petroleum fuel/chemicals, but the total CO 2 reduction potential is 935–1777 MMT/year.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Integrated low carbon H 2 conversion with in situ carbon mineralization from aqueous biomass oxygenate precursors by tuning reactive multiphase chemical interactions

Meeting our rising demand for clean energy carriers such as H 2 from renewable biomass resources is challenged by the co-emission of CO 2 and CH 4 . To address this challenge, we design novel reactive separation pathways that integrate multiphase chemical reactions by harnessing Ca and Mg bearing minerals as a sorbent to capture CO 2 released during the hydrothermal deconstruction of aqueous biomass oxygenates to produce H 2 and solid carbonates via low temperature aqueous phase reforming and thermodynamically downhill carbon mineralization. Earth abundant catalysts such as Ni/Al 2 O 3 are effective in producing H 2 yields as high as 79% and 74% using ethylene glycol and methanol in the presence of Ca(OH) 2 as an alkaline sorbent, without contaminating or deactivating the catalyst. H 2 yields with in situ carbon mineralization using a Ni or Pt/Al 2 O 3 catalyst are enhanced based on the following order of reactivity: acetate < glycerol < methanol < formate < ethylene glycol. These studies demonstrate that the multiphase chemical interactions can be successfully tuned to enhance H 2 yields through the selective cleavage of C–C bonds using Ni/Al 2 O 3 catalysts to deconstruct biomass oxygenates for producing H 2 and CO 2 , and in situ carbon mineralization by harnessing abundant alkaline materials, as demonstrated using ladle slag. This approach unlocks new scientific possibilities for harnessing multiple emissions including abundant organic-rich wastewater streams and alkaline industrial residues to co-produce low carbon H 2 and carbonate-bearing materials for use in construction by using renewable solar thermal energy resources.

09 BIOMASS FUELS↗
DOE OSTI2023

Synthetic Calcium Carbonate Production by Carbon Dioxide (CO 2 ) Mineralization of Industrial Waste Brines

The global scale of CO 2 emission has crossed 36 B tons, and the United State represents 14% of the total emissions. In light of the high cost associated with current CO 2 capture processes ($60-to-150 per ton of CO 2 ), carbon capture and utilization (CCU), wherein CO 2 is converted to beneficial products, provides a pragmatic path to overcome the economic barrier for CO 2 emissions control. In particular, CO 2 mineralization offers an attractive route as it produces high-value mineral carbonates that sequester CO 2 in a stable form. For instance, fine precipitated calcium carbonate, a valuable product with unit price in the range of $230-280/t and a global market projected to reach 99 M tons in 2020, can be produced by capturing CO 2 within aqueous Ca 2+ solution. However, two critical challenges need to be overcome—(i) the need for costly processes such as electrolysis or addition of alkali hydroxides to maintain alkalinity during mineralization, and (ii) the geographic availability of Ca-rich solutions (or brines) which often renders efficient integration with power plants impractical. To simultaneously address these challenges, this project developed two novel routes to enable carbonate production based on efficient CO 2 mineralization. In one variation, the project developed a new alkaline carbonation process to capture CO 2 and produce calcite precipitates from coal ashes. Herein, coal ash is carbonated first in a sodium carbonate solution. The carbonation reaction produces sodium hydroxide and raises the solution pH. This high-pH hydroxide solution is then used for CO 2 capture, which converts the sodium hydroxide solution back to sodium carbonate to repeat the carbonation cycle. The carbonated ash residue is refined with a CO 2 pressure swing step to produce high-purity precipitated calcium carbonate. In another variation, Ca-rich produced water brine serves as the Ca-source to mineralize CO 2 . An H + /Na + ion-exchange cycle was designed to provision alkalinity during mineralization and regenerate the ion-exchange reagent in brines with high salinity. Ca-depleted brines can then be treated within a centralized water treatment facility. Both variations beneficially utilize reject streams—such as coal ashes and brines from oil and gas extraction or CO 2 storage operations—that are available at substantial quantities in the vicinity of coal power plants within the U.S. In addition to technology development, this project included techno-economic and life-cycle analysis to identify technically and economically appropriate solutions for power plants in different geographic locations. Taken together, the project provides a unique route to integrate CO 2 emissions control and waste handling/treatment for coal power plants, while producing a high-value product to offset the economic burden associated with waste management. The developed processes utilize post-desulfurization flue gas from coal-fired power plants as is. The CO 2 conversion reactions are performed in alkaline brines at ambient pressure from the flue gas, thereby minimizing the energy burden. By beneficiation of industrial waste streams with low energy input, the processes offers significant technical advantages in energy and CO 2 footprint over the current paradigm of precipitated calcium carbonate production, which involves calcination of limestone at processing temperatures in excess of 800 °C. Overall, this project developed viable CO 2 mineralization processes while strategically maximizing the economic benefit.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Recent Advances and Future Perspectives of Low-Concentration CO 2 Enrichment and Emerging Applications

Low-concentration carbon dioxide (LCCO 2 ) streams, ranging from ambient air to industrial flue gas, represent a significant yet underutilized carbon resource. This review examines recent advances in technologies for enriching LCCO 2 and enabling its integration into a wide range of applications. It covers emerging materials and processes for CO 2 capture, including immobilized amines, metal oxides, polymers, porous carbons, and zeolites, with a focus on performance metrics, regeneration strategies, and process intensification. Beyond capture, the review explores the direct utilization of LCCO 2 through reactive capture pathways enabled by novel catalysts and processes, as well as nonreactive applications, such as greenhouse cultivation, enhanced weathering, and sustainable agriculture. Additionally, this review highlights the role of LCCO 2 in enhancing critical metal recovery. Finally, the review outlines crucial future research directions necessary to fully realize LCCO 2 enrichment’s potential within circular carbon economies and critical material supply chains, paving the way toward a more energy-innovative and resource-resilient industrial sector. The findings are significant for researchers in academia, industry, and government, as well as the public interested in extending the value of LCCO 2 .

atmospheric chemistry↗
DOE OSTI2022

Cost of Capturing CO 2 from Industrial Sources

This systems analysis by the National Energy Technology Laboratory's Strategic Systems Analysis and Engineering directorate) evaluates the cost and performance impacts of capturing CO 2 emissions from nine industrial sources (ammonia, ethylene oxide, and ethanol production, natural gas process, coal- and gas-to-liquids, refinery hydrogen production, iron and steel, and cement manufacturing). The industrial sectors examined are segregated according to the CO 2 purity level of the flue gas stream, prior to treatment. Certain sectors naturally produce a gas stream that is inherently high in CO 2 purity, and these sectors can achieve 99-100% removal. Other sectors produce a lower purity CO 2 flue gas stream and achieving 90-99% removal requires deeper levels of treatment, adding cost. In addition to the report that documents the analysis, a Carbon Capture Retrofit Database tool was also created that allows users to apply CO 2 capture to selected industries, to evaluate the cost of capture and compare across multiple plants, as well as across different industries. Users have the ability to change select input parameters (such as fuel price, capture rate, and financing assumptions) to evaluate the impact on industrial CO 2 capture economics.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Process intensification of CO 2 capture by low-aqueous solvent

Low-energy solvent-based CO 2 absorption processes have drawn attention as a next-generation post-combustion CO 2 capture technology to reduce CO2 emissions from fossil fuel– or biomass-fired power generation and industrial flue gas streams. A low-aqueous (or water-lean) solvent process may substantially reduce the thermal energy consumption for solvent regeneration. Low-aqueous solvent–based processes are thermally sensitive, requiring a delicate temperature control within the absorber because of the fast exothermic amine-CO 2 reaction and low heat capacity organic diluent. This reaction may result in heat accumulation in a packed absorption column and undesirable CO 2 desorption occurring as the solvent moves through the column, reducing the solvent’s CO 2 capture efficiency if its temperature is not controlled. Using a 3D printed intensified packing device, enhanced heat and mass transfer were demonstrated in an amine-CO 2 scrubbing process using low-aqueous solvent. The multifunctional intensified device facilitates contact of the reactive solvent and gas phases in a single stage and heat removal by a cooling fluid flowing through channels in the interior of the corrugated plates of the device. These functionalities led to effective thermal management along the column via intrastage cooling and significant improvement in CO 2 uptake under a wide range of operating conditions. Intrastage cooling effectively reduced the solvent average temperature along the column by ~10 °C and, as a result, the solvent’s capture efficiency improved by up to 25%.

42 ENGINEERING↗
DOE OSTI2021

Carbon capture, utilization, and storage hub development on the Gulf Coast

Abstract The Gulf Coast of the United States hosts diverse power generation, refining, and petrochemical processing facilities, resulting in the nation's largest volumetric concentration of industrial CO 2 emissions, rivaled only by the Ohio River Valley. These emissions sources are concentrated in specific industrial clusters that allow combining emissions streams to achieve economies of scale. The region is currently undergoing globally significant industrial expansion and investment as a result of abundant and inexpensive regional unconventional natural gas availability, and is a growing exporter of liquefied natural gas (LNG). Opportunities to integrate CO 2 emission management within the diverse energy chains in the region are volumetrically significant and include both concentrated and dilute sources. Significant examples of capture, transport, and storage exist. Offshore storage is particularly attractive, as it provides simplified land leasing models (single governmental land owner), proven reservoir quality, and presents fewer risks to both protected groundwater and populated areas. Projects can now take advantage of recently expanded opportunities under section 45Q of the Internal Revenue Service tax code. The region continues to evolve as an active carbon‐handling hub, and is uniquely suited to justify additional investment in carbon capture, utilization, and storage (CCUS) technologies via a large‐scale integrated project development. Continued development of integrated projects will allow the region to continue to grow economically within its strong fossil‐fuel handling competence focus while advancing low‐carbon energy technologies that maintain globally competitiveness. © 2021 The Authors. Greenhouse Gases: Science and Technology published by Society of Chemical Industry and John Wiley & Sons Ltd.

45Q↗