Results for “Integrated Computational Material and Engineering (ICME)”

DOE OSTI2024

7th World Congress on Integrated Computational Materials Engineering (ICME 2023) (Final Technical Report)

Integrated Computational Materials Engineering (ICME) has received international attention due to its potential to shorten product development time, while lowering cost and improving design and manufacturing outcomes. ICME is an approach to designing materials solutions for specific applications that use computer modeling programs to predict the behavior of materials and integrate this information into the overall materials, processing, and manufacturing design cycle. The 7th World Congress on Integrated Computational Materials Engineering (ICME 2023) was held in Orlando, Florida from May 21–25, 2023 with the goal to convene stakeholders from across all areas of modeling and simulation, experimental specialization, and design, as well as from across academia, government, and industry, to address ICME tools and techniques and their integration, as well as to examine their application in engineering. This atmosphere facilitated rich interactions between the experimentalists, modelers, and computational and design, from academia, government, and industry, to discuss ICME tools and techniques and their application in engineering.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Lightweight Materials - Carbon Fiber and Polymer Composites, Integrated Computational Materials Engineering (ICME) Predictive Tools Development for Low-Cost Carbon Fiber for Lightweight Vehicles (University of Virginia) (Final Report)

This project aimed to develop low-cost alternative precursors and processing techniques through the implementation of an integrated computational materials engineering (ICME) framework to evaluate precursor conversion kinetics. Once established, this framework was then used to down-select precursors for laboratory- and pilot-scale production to validate resulting carbon fiber (CF) material properties and process cost-savings. The two most promising approaches to reduce the cost of CFs were to (1) use new low-cost precursors and (2) reduce the energy requirements of CF processing. These approaches were investigated over the course of three phases of work, spanning 3.5 years. This report describes the overall project objectives, approach, and the key accomplishments in each phase.

36 MATERIALS SCIENCE↗

DOE OSTI2026

An Integrated Computational Materials Engineering (ICME) Approach to Design Nonlinear Transition Zones Between Dissimilar Metals

Current approaches to designing graded transition joints (GTJs) between dissimilar metals often rely on linear changes in both composition profiles and thickness of each sublayer. This increases fabrication cost and may not be optimal with respect to residual stress or the formation of undesirable phases. Here, in this study, GTJs between P91 ferritic/martensitic steel and 347H austenitic stainless steel were designed using Integrated Computational Materials Engineering (ICME) principles with nonlinear composition and length profiles. Guided by inputs from classical mechanics and CALPHAD predictions of carbon chemical potential, a novel transition zone consisting of five discrete compositions was proposed, with the thickness of each sublayer varying according to a brachistochrone-inspired distribution. In addition to carbon potential gradients, CALPHAD was used to predict coefficients of thermal expansion, which were incorporated into finite element models to evaluate stress evolution. The proposed nonlinear design resulted in a smoother carbon potential gradient, lower carbon depletion at the P91 interface, and a comparable residual stress under long-term thermal exposure, compared to a conventional linear design using ten sublayers with equal thickness. This work introduces a brachistochrone-inspired distribution for GTJ design, offering a general framework for optimizing graded interfaces between dissimilar metals.

Directed Energy Deposition↗

DOE OSTI2022

A perspective on Bayesian methods applied to materials discovery and design

For more than two decades, there has been increasing interest in developing frameworks for the accelerated discovery and design of novel materials that could enable promising and transformative technologies. The Integrated Computational Materials Engineering (ICME) program called for integrating computational tools to establish linkages along process-structure-property-performance (PSPP) chains. The Materials Genome Initiative called for integrating experiments and computations within data science frameworks as a strategy to accelerate the materials development cycle. While these frameworks and paradigms have been quite influential, traditional ICME or data science-based approaches tend to have some limitations, mainly when querying the materials space is costly and very little information is available. Bayesian methods are more suitable in this context due to their efficiency gains. To this end, the materials discovery problem is framed as a Bayesian Optimization (BO). Different examples in which BO has been applied to solve materials discovery problems are presented. The methods/examples discussed include BO under model uncertainty, multi-information source BO, multi-objective and multi-constraint BO, and batch BO. Bayesian Materials Discovery is a promising area of research that is likely to become more influential as more attention is put on autonomous materials discovery platforms. Therefore, a discussion is provided on the potential development of such methods to increase the ability of existing platforms in materials discovery. Here, the ultimate goal is to pave the way to autonomous materials discovery.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Materials Design using an Active Subspace-based Batch Bayesian Optimization Approach

Integrated computational materials engineering (ICME) calls for integrating simulation tools and/or experiments to develop new materials and materials systems. However, implementation of ICME approaches is challenging mainly due to the considerable computational expense of such frameworks and large dimensionality of the design space. Addressing these challenges is thus critical to the success of ICME initiatives. We present here a specific Bayesian optimization framework designed to address these two challenges. In particular, we propose an active subspace batch Bayesian optimization framework. The framework makes use of dimension reduction via the active subspace method and makes use of the ability to query in parallel via the batch Bayesian optimization approach. Here, the integration of these techniques leads to significant efficiency improvements while maintaining accuracy.

36 MATERIALS SCIENCE↗

DOE OSTI2022

AI-Enabled Discovery and Physics-Based Optimization of Energy Efficient Processing Strategies for Advanced Turbine Alloys (Final Technical Report)

In this project, the multi-organizational team of academic and industrial researchers from the University of Kentucky an aerospace and energy generation OEM partner has leveraged novel Digital Process Twin (DPT) models of process/structure interactions (i.e., process-induced surface integrity) to advance a paradigm of fully integrated computational materials engineering (ICME). Using efficient process models as the core of a digital process simulator for a reinforcement learning algorithm, the team has integrated industrial data and metrics of structure/performance/energy relationships and manufacturing-related energy metrics to optimize dynamic processing parameters for significantly improved life-cycle energy efficiency of advanced γ-TiAl low-pressure turbine (LPT) alloys, as indicated by a set of design relevant parameters (e.g., residual stresses and scrap rate). The key objective and anticipated outcome of the project was at least a 10% reduction in life-cycle embodied energy for a recently developed, γ-TiAl low-pressure turbine (LPT) alloy and nickel-based superalloy Inconel 718, through the adoption of the proposed AI-enabled process optimization approach. The final project outcomes significantly exceeded this original target, realizing manufacturing-related energy efficiency improvements of more than 130% for TiAl and up to 80% for Inconel 718. Rather than following the prevailing and highly inefficient empirical paradigm, the proposed study demonstrated the feasibility of adopting a digital, physics-based process design and optimization paradigm. The recurring need for manual intervention, rework, reinspection causes significant production bottlenecks and unnecessary expense associated with delivering the requisite component quality. The OEM partner, and turbine industry in general, expect to reap significant cost and resource savings if an AI-optimized set of parameters can be applied to specific machining operations. The technical scope of the proposed project involved the paving of a realistic path towards model-based and AI-enabled Integrated Computational Materials Engineering (ICME), and away from inefficient empirical process optimization and legacy manufacturing practices, which are no longer able to efficiently process novel high-performance turbine alloy materials. The project team will address the fundamental knowledge gap that currently exists within the ICME paradigm with respect to the process/structure/performance/energy impacts of finishing processes. While significant resources have been devoted to the ‘early stages’ of manufacturing, such as alloy design, primary and secondary processing, finishing processes have not been adequately integrated within ICME. To provide an actionable path towards model-based finishing process design (e.g., machining, burnishing, grinding, polishing), we will employ a novel AI-enabled process optimization paradigm, based on a computationally efficient, physics-based process simulator. Through limited experimental work to calibrate and validate our process simulator model via an advanced in-situ characterization technique and process optimization via reinforcement learning, the project will seek to demonstrate a viable alternative to the inefficient ‘legacy’ processing strategies, empirical testing and broad scope machining learning approaches, all of which fail to adequately consider complex process physics. The project team has identified an intermetallic γ-TiAl LPT alloy, which is currently being used as part of the OEM partner’s advanced gas turbine designs. This particular alloy poses significant manufacturing challenges during finishing operations, which limit the degree to which the current turbine design can be manufactured in an energy- and cost-efficient manner. Empirical testing and numerical modeling efforts to optimize processing parameters for γ-TiAl have not been able to resolve these manufacturing challenges, so the proposed physics-based AI-enabled optimization technology would offer a truly novel and transformative capability. The multi-organizational team of academic and industry experts from the UKY and the OEM partner will work together closely to demonstrate the analytical and experimental critical function and characteristic proof of concept of this novel approach.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2022

A Stochastic Reduced-Order Model for Statistical Microstructure Descriptors Evolution

Integrated computational materials engineering (ICME) models have been a crucial building block for modern materials development, relieving heavy reliance on experiments and significantly accelerating the materials design process. However, ICME models are also computationally expensive, particularly with respect to time integration for dynamics, which hinders the ability to study statistical ensembles and thermodynamic properties of large systems for long time scales. To alleviate the computational bottleneck, we propose to model the evolution of statistical microstructure descriptors as a continuous-time stochastic process using a non-linear Langevin equation, where the probability density function (PDF) of the statistical microstructure descriptors, which are also the quantities of interests (QoIs), is modeled by the Fokker–Planck equation. In this work, we discuss how to calibrate the drift and diffusion terms of the Fokker–Planck equation from the theoretical and computational perspectives. The calibrated Fokker–Planck equation can be used as a stochastic reduced-order model to simulate the microstructure evolution of statistical microstructure descriptors PDF. Considering statistical microstructure descriptors in the microstructure evolution as QoIs, we demonstrate our proposed methodology in three integrated computational materials engineering (ICME) models: kinetic Monte Carlo, phase field, and molecular dynamics simulations.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

Benchmarking of massively parallel phase-field codes for directional solidification

We present a detailed benchmark comparing two state-of-the-art phase-field implementations for simulating alloy solidification under experimentally relevant conditions. The study investigates the directional solidification of Al-3wt%Cu under high-velocity solidification conditions and SCN-0.46wt% camphor under microgravity conditions from National Aeronautics and Space Administration (NASA) DECLIC-DSI-R experiments. Both codes, one employing finite-difference discretization with uniform mesh and GPU-acceleration (GPU-PF) and the other one employing finite-element discretization with adaptive-mesh and CPU-parallelization (PRISMS-PF), solve the same quantitative phase-field formulation that incorporates an anti-trapping current for the solidification of dilute alloys. We evaluate the predictions of each code for dendritic morphology, primary spacing, and tip dynamics in both 2D and 3D, as well as their numerical convergence and computational performance. While existing benchmark problems have primarily focused on simplified or small-scale simulations, they do not reflect the computational and modeling challenges posed by employing experimentally relevant time and length scales. Our results provide a practical framework for assessing phase-field code performance as well as validating and facilitating their application in integrated computational materials engineering (ICME) workflows that require integration with realistic experimental data.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Data Mining and Visualization of High-Dimensional ICME Data for Additive Manufacturing

Integrated computational materials engineering (ICME) methods combining CALPHAD with process-based simulations can produce rich, high-dimensional data for alloy and process design. In ICME methods for metallurgical applications, the visualization and interpretation of such high-dimensional data has previously been through heat maps represented in 2 or 3 dimensions. While such an approach is ideal when one variable is varied at a time, in the case of high-dimensional data with multiple variables varied simultaneously, as is the case in additive manufacturing, interpreting the trends through two- or three-dimensional heat maps becomes challenging. Here, we propose a strategy of mixed visual data mining and quantitative analysis for high-dimensional metallurgical and process data using high-throughput thermodynamic calculations. Two case studies show the application of the proposed approach. The first case study investigated the effects of feedstock chemistry on the δ ferrite formation in 316L stainless steel powders used for binder jet additive manufacturing. The second case study linked Scheil–Gulliver calculations to a process model for dissimilar joining of aluminum alloys 5356 and 6111 during laser hot-wire additive manufacturing. Both cases contained thousands of calculated data points, showcasing the utility of visual data analysis through parallel coordinate plotting, Pearson correlation coefficient matrices, and scatter matrices compared to traditional process maps. These visualization techniques can be extended to many additive manufacturing problems to capture process–structure–property relationships for additively manufactured components.

36 MATERIALS SCIENCE↗

DOE OSTI2020

An integrated computational materials engineering framework to analyze the failure behaviors of carbon fiber reinforced polymer composites for lightweight vehicle applications

A bottom-up multi-scale modeling approach is used to develop an Integrated Computational Materials Engineering (ICME) framework for carbon fiber reinforced polymer (CFRP) composites, which has the potential to reduce development to deployment lead time for structural applications in lightweight vehicles. In this work, we develop and integrate computational models comprising of four size scales to fully describe and characterize three types of CFRP composites. In detail, the properties of the interphase region are determined by an analytical gradient model and molecular dynamics analysis at the nano-scale, which is then incorporated into micro-scale unidirectional (UD) representative volume element (RVE) models to characterize the failure strengths and envelopes of UD CFRP composites. Then, the results are leveraged to propose an elasto-plastic-damage constitutive law for UD composites to study the fiber tows of woven composites as well as the chips of sheet molding compound (SMC) composites. Subsequently, the failure mechanisms and failure strengths of woven and SMC composites are predicted by the meso-scale RVE models. Finally, building upon the models and results from lower scales, we show that a homogenized macro-scale model can capture the mechanical performance of a hat-section-shaped part under four-point bending. Along with the model integration, we will also demonstrate that the computational results are in good agreement with experiments conducted at different scales. The present work illustrates the potential and significance of integrated multi-scale computational modeling tools that can virtually evaluate the performance of CFRP composites and provide design guidance for CFRP composites used in structural applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Integrated Computational Materials and Mechanical Modeling for Additive Manufacturing of Alloys with Graded Structure Used in Fossil Fuel Power Plants

Wire-arc additive manufacturing (WAAM) has demonstrated its unique capability of producing large-size alloy components with a significantly reduced fabrication time and enhanced geometry design freedom. In this project, the team has developed an ICME (Integrated Computational Materials Engineering) modeling framework, which supports the WAAM of the AUSC (Advanced Ultra-Supercritical) power plant components. The manufacturing design has been applied to Inconel 740H, steel P91, as well as the dissimilar alloy components between steel P91 and Inconel 740H. The ICME model framework is developed by considering two types of modeling. First, mechanistic modeling has been applied to control the printing quality and understand the sequence of the dissimilar printing of the wall structure. The following models have been included in the developed ICME framework: finite element thermal model, grain structure model, residual stress simulation, crystal plasticity model, CALPHAD-based precipitation kinetic model, phase stability prediction, thermal expansion predictive model, and heuristic creep model. Secondary, a physics-based machine learning model has also been developed based on the ICME model structure. The machine learning model development is based on the ICME model prediction with calibration of the experiments. In addition, the WAAM has been utilized as a high-throughput experimental tool rapidly generating a gradient of alloy composition to facilitate experimental database generation for process-structure-property relationships. Such a database directly supported the ICME-enhanced machine learning, which further assisted in intermediate composition block design between P91 and 740H. A high-throughput screening study of the oxidation resistance has been performed based on such high-throughput experimentation. Based on the computational design, several dissimilar alloy manufacturing with post-heat treatment have been performed with a comprehensive evaluation of mechanical performance, including hardness mapping, yield strength, creep resistance. In this project, the single component of P91 and 740H processed by WAAM after heat treatment designed by ICME has demonstrated higher performance in yield strength and creep resistance than the wrought materials. The P91 sample prepared by WAAM with ICME-designed heat treatment performs better than P92 in creep resistance. The designed graded alloy printing with intermediate block shows a promising performance that exceeds the traditional welding. Moreover, the current research indicates the high need for location-specific design analysis with uncertainty quantification, an important topic that deserves more dedicated research. The achievement of this project demonstrated the promising future of WAAM in structural alloy manufacturing for energy power plant development. Successful printing requires synergetic efforts made by manufacturing, mechanical, and materials sciences.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2024

Anomaly Detection in Materials Digital Twins with Multiscale ICME for Additive Manufacturing

Detecting anomaly in fatigue and fracture experimental materials science is an interesting yet challenging topic. The reasons are threefold. First, the anomalous microstructure feature that gives rise to structural failure is small, sometimes in the order of 10 -7 of the interrogated volume. This, in turn, results in a highly imbalanced classification problem in machine learning (ML). Second, the consequence is high, in the sense that the test specimen is destructed in such case. Third, the convolution between microstructure stochasticity and the small probability of void nucleation, growth, and coalescence makes failure and fracture a hard-to-predict and challenging problem in materials science due to its irreproducibility, even experimentally. In this paper, we developed a materials digital twin and applied anomaly detection methods to detect voids and anomaly in additive manufacturing (AM). The materials digital twin is driven by two integrated computational materials engineering (ICME) models, which are kinetic Monte Carlo (kMC) and crystal plasticity finite element method (CPFEM). In conclusion, we demonstrated that by using anomaly detection, it is possible to detect voids and other defects in materials digital twin, which paves way for future research in integrating materials digital twin with its physical counterpart.

ICME↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogenities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogenities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

CALPHAD-based ICME design of single-step aging to enhance mechanical strength of WAAM Haynes 282

To match the strength of wire-arc additive manufactured Haynes 282 to its wrought counterpart via a single-step aging heat treatment, the CALPHAD (Calculation of Phase Diagrams) method is integrated with physics-based process-structure-property models and experimental validation. The integrated computational materials engineering (ICME) framework simulates the effects of aging on γ′ and M 23 C 6 precipitation and the resulting yield strength. To improve simulation reliability, the interfacial energies between γ/γ′ and γ/M 23 C 6 carbides were estimated by comparison with precipitation kinetic modeling and measured precipitate sizes. γ′ and M23C6 were found to precipitate simultaneously between 640 and 860 °C, producing microstructures similar to those produced by two-step aging. The optimal γ′ size for peak yield stress was calculated to be 20–23 nm. WAAM Haynes 282 aged at 780 °C for 50 h exceeded the mechanical performance of its wrought counterpart subjected to two-step aging, though desired properties can also be achieved at 800 °C for 16 h or less. The error in yield strength is less than 20 MPa, demonstrating good agreement between the modeling framework and experiments. Creep studies showed that WAAM Haynes 282 exceeded the calculated rupture time, reaching 481 h. This proposed methodology can accelerate the design of aging heat treatments for any γ′-strengthened nickel-base alloy, minimizing the resources required for trial-and-error experiments.

CALPHAD↗