Search NASA⌕ Search

SEARCH · Search NASA

Results for “KAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Understanding the effect of friction stir processing on electrical steel: Microstructural changes and mechanical transformations

Raising Si beyond 3.5 wt% reduces core loss but embrittles electrical steels, constraining processing and application. Here we assess friction stir processing (FSP) as a solid‑state route to enable Fe–4.0 wt% Si with improved mechanical performance. Temperature‑controlled FSP with a PcBN tool produced a defect‑free processed zone. SEM/EBSD revealed dynamic recrystallization and grain refinement from an average 110 μm in the base material to ∼20 μm in the processed region, with ∼ 80% of grains < 40 μm and a reduction in high‑angle boundary fraction to ∼65% (vs >85% in the base). Comparative mechanical property analysis shows a moderate increase in yield strength in FSP samples relative to the base material, with a significant improvement in ductility (∼35–50%). Post‑fracture EBSD identified 60° twin boundaries in the base while sub-grain formation with elevated KAM in the FSP sample. Fractography revealed a shift from quasi‑cleavage in the Base-faceted planes with river patterns, steps, and occasional secondary cracks—to ductile micro void coalescence after FSP. Following FSP, the material retains soft‑magnetic behavior, with modest shifts in saturation magnetization consistent with grain refinement and stored strain, accompanied by a clear gain in formability. These results indicate that FSP provides a viable route to deploy higher‑Si electrical steels with concurrent gains in strength and ductility.

Electrical steel↗
DOE OSTI2024

Radiation Damage Mitigation in FeCrAl Alloy at Sub-Recrystallization Temperatures

Traditional defect recovery methods rely on high-temperature annealing, often exceeding 750 °C for FeCrAl. In this study, we introduce electron wind force (EWF)-assisted annealing as an alternative approach to mitigate irradiation-induced defects at significantly lower temperatures. FeCrAl samples irradiated with 5 MeV Zr 2+ ions at a dose of 10 14 cm −2 were annealed using EWF at 250 °C for 60 s. We demonstrate a remarkable transformation in the irradiated microstructure, where significant increases in kernel average misorientation (KAM) and low-angle grain boundaries (LAGBs) typically indicate heightened defect density; the use of EWF annealing reversed these effects. X-ray diffraction (XRD) confirmed these findings, showing substantial reductions in full width at half maximum (FWHM) values and a realignment of peak positions toward their original states, indicative of stress and defect recovery. To compare the effectiveness of EWF, we also conducted traditional thermal annealing at 250 °C for 7 h, which proved less effective in defect recovery as evidenced by less pronounced improvements in XRD FWHM values.

FeCrAl alloys↗
DOE OSTI2026

Analysis of the electrical double layer using electrochemical X-ray photoelectron spectroscopy

The element-sensitivity of X-ray spectroscopies offers the potential to disentangle the individual chemistries of water, ions, and adsorbates at the electrode-electrolyte interface in an element-by-element manner. However, targeted experimental design is needed to establish interface-sensitive in situ X-ray spectroscopy in a realistic electrochemical environment. Here, we demonstrate how electrochemical X-ray photoelectron spectroscopy (EC-XPS) in the dip-and-pull geometry can be used to specifically probe the behavior of ions in the electrical double layer. Taking the case study of a polycrystalline Au foil in 50 mM KClO 4 electrolyte, we tracked the electrochemical response of interfacial K + cations across a broad potential range. We show how, in combination with modeling, key parameters such as the potential of zero charge (PZC), ion packing behavior, dielectric saturation, and the electrostatic potential decay in the double layer can be extracted from the data. Importantly, we also analyze how the experimental conditions and non-idealities can influence the results and put forward criteria for reliable experimentation and data analysis.

Dip-and-pull↗
DOE OSTI2024

Containment strategy for subsurface H 2 storage based on time-dependent soft solids

Here, we propose an innovative containment strategy based on time-dependent soft solids, namely 2 wt% Laponite suspensions, to reinforce natural subsurface seals and engineer flow barriers, with an eye toward making H 2 subsurface storage scalable and geographically agnostic. This suspension can be injected at its initial low viscosity and elasticity into a porous medium, allowing for easy pumping and targeted delivery. Once inside the target zone, it matures into a soft solid with much higher viscosity and elasticity, acting as a potential flow barrier. We discuss the rheological properties of the suspensions and demonstrate that hydrogen does not adversely affect their microstructure, but rather increases the suspensions’ viscosity and elasticity. Moreover, the suspensions enhance the rock samples’ compressive strength, while hydrogen exposure increases their stiffness and ductility. The ability of rock samples saturated with the suspensions to contain higher injected gas pressures is enhanced by aging at higher temperatures.

08 HYDROGEN↗
DOE OSTI2025

Kramers nodal lines in intercalated TaS 2 superconductors

Kramers degeneracy is one fundamental embodiment of the quantum mechanical nature of particles with half-integer spin under time reversal symmetry. Under the chiral and noncentrosymmetric achiral crystalline symmetries, Kramers degeneracy emerges respectively as topological quasiparticles of Weyl fermions and Kramers nodal lines (KNLs), anchoring the Berry phase-related physics of electrons. However, an experimental demonstration for ideal KNLs well isolated at the Fermi level is lacking. Here, we establish a class of noncentrosymmetric achiral intercalated transition metal dichalcogenide superconductors with large Ising-type spin-orbit coupling, represented by In x TaS 2 , to host an ideal KNL phase. We provide evidence from angle-resolved photoemission spectroscopy with spin resolution, angle-dependent quantum oscillation measurements, and ab-initio calculations. Our work not only provides a realistic platform for realizing and tuning KNLs in layered materials, but also paves the way for exploring the interplay between KNLs and superconductivity, as well as applications pertaining to spintronics, valleytronics, and nonlinear transport.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Two datasets are better than one: method of double moments for 3D reconstruction in cryo-EM

Cryo-electron microscopy is a powerful imaging technique for reconstructing three-dimensional molecular structures from noisy tomographic projection images of randomly oriented particles. We introduce a new data fusion framework, termed the method of double moments, which reconstructs molecular structures from two instances of the second-order moment of projection images obtained under distinct orientation distributions: one uniform, the other non-uniform and unknown. We prove that these moments generically uniquely determine the underlying structure, up to a global rotation and reflection, and we develop a convex-relaxation-based algorithm that achieves accurate recovery using only second-order statistics. Our results demonstrate the advantage of collecting and modeling multiple datasets under different experimental conditions, illustrating that leveraging dataset diversity can substantially enhance reconstruction quality in computational imaging tasks.

Kam’s method↗
DOE OSTI2025

The Simons Observatory: validation of reconstructed power spectra from simulated filtered maps for the small aperture telescope survey

We present a transfer function-based method to estimate angular power spectra from filtered maps for cosmic microwave background (CMB) surveys. This is especially relevant for experiments targeting the faint primordial gravitational wave signatures in CMB polarisation at large scales, such as the Simons Observatory (SO) small aperture telescopes. While timestreams can be filtered to mitigate the contamination from low-frequency noise, usual methods that calculate the mode coupling at individual multipoles can be challenging for experiments covering large sky areas or reaching few-arcminute resolution. The method we present here, although approximate, is more practical and faster for larger data volumes. We validate it through the use of simulated observations approximating the first year of SO data, going from half-wave plate-modulated timestreams to maps, and using simulations to estimate the mixing of polarisation modes induced by an example of time-domain filtering. We show its performance through an example null test and with an end-to-end pipeline that performs inference on cosmological parameters, including the tensor-to-scalar ratio r. The performance demonstration uses simulated observations at multiple frequency bands. We find that the method can recover unbiased parameters for our simulated noise levels.

CMBR experiments↗
DOE OSTI2025

Interplay between electron localization, magnetic order, and Jahn-Teller distortion dictates LiMnO2 phase stability

The development of manganese (Mn)-rich cathodes for Li-ion batteries promises to alleviate potential supply chain bottlenecks in battery manufacturing. Fundamental challenges in Mn-rich cathodes arise from phenomena such as structural changes due to cooperative Jahn-Teller (JT) distortions of in octahedral environments, Mn migration, and phase transformations to spinel-like order, all of which affect the electrochemical performance. These physically complex phenomena motivate an re-examination of the Li-Mn-O rock-salt space, with a focus on the thermodynamics of the prototypical, polymorphs. It is found that the generalized gradient approximation (GGA-PBEsol) and meta-GGA ( ) density functionals with empirically fitted on-site Hubbard corrections yield spurious stable phases for , such as predicting a phase with -like order ( ) to be the ground state instead of the orthorhombic (Pmmn) phase, which is the experimentally known ground state. Accounting for antiferromagnetic order in each structure is shown to have a substantial effect on the total energies and resulting phase stability. By using hybrid-GGA (HSE06) and GGA with self-consistent Hubbard parameters (on-site and inter-site ) calculated from linear response theory, the experimentally observed phase stability trends are recovered. The calculated on-site between Mn- states in the experimentally observed orthorhombic, layered, and spinel phases are significantly smaller than in and disordered layered structures, by within GGA. The smaller values of are shown to be correlated with a collinear ordering of JT distortions, in which all orbitals are oriented in the same direction. This cooperative JT effect can lead to greater electron delocalization from Mn along the states due to increased Mn-O covalency, which contributes to the greater electronic stability compared to the phases with noncollinear JT arrangements. The structures with collinear ordering of JT distortions also generate greater vibrational entropy, which helps stabilize these phases at high temperature. These phases are shown to be strongly insulating with large calculated band gaps , which are computed using HSE06 and .

Kam, Ronald L↗
DOE OSTI2026

Constraints on the polarization angle oscillations of the Crab Nebula with the Simons Array and its applications to the search for axionlike particles

Here, we present a search for polarization oscillation of the Crab Nebula, also known as Tau A, at millimeter wavelengths using observations with the Simons Array, the successor experiment to POLARBEAR. We follow up on previous work by POLARBEAR using 90 GHz band data of the 2023 observing season of the Simons Array to evaluate the variability of Tau A’s polarization angle. Tau A is widely used as a polarization angle calibration source in millimeter-wave astronomy, and thus it is necessary to validate the stability. Additionally, an interesting application of the time-resolved polarimetry of Tau A is to search for axionlike particles (ALPs). We do not detect a global signal across the frequencies considered in this analysis and place a median 95% upper bound of polarization oscillation amplitude A < 0.12° over oscillation frequencies from 3.39 yr -1 to 1.50 day -1 . This constrains the ALP-photon coupling at a median 95% upper bound of g aγγ < 3.84 × 10 -12 × (m a /10 -21 eV) in the mass range from 4.4 × 10 -22 to 7.2 × 10 -20 eV, assuming the ALP constitutes all of dark matter, its field is a stochastic Gaussian field, and it is the sole source of Tau A’s polarization angle oscillation. Additionally, we do not detect signal at the frequencies where 2.5σ hints were previously reported by POLARBEAR, but we do not exclude these signals at the 95% confidence level.

Adkins, Tylor [University of California, Berkeley]↗
DOE OSTI2025

Anomalous Hall effect emerging from field-induced Weyl nodes in SmAlSi

The intrinsic anomalous Hall effect (AHE) has been reported in numerous ferromagnetic Weyl semimetals. However, the AHE in the antiferromagnetic (AFM) or paramagnetic (PM) state of Weyl semimetals has rarely been observed experimentally. Different mechanisms have been proposed to account for the emergence of the AHE from different types of magnetic order. Here, in this Letter, we propose a new model that explains the observed AHE in both the AFM and PM states of the noncentrosymmetric Weyl semimetal SmAlSi. The newly proposed mechanism is based on magnetic-field-induced Weyl node evolution, which qualitatively explains the temperature dependence of the anomalous Hall conductivity, which displays unconventional power-law behavior in both the AFM and PM states of SmAlSi.

Gao, Yuxiang [Rice University, Houston, TX (United↗
DOE OSTI2025

Observation of edge supercurrent in topological antiferromagnet MnBi 2 Te 4 -based Josephson junctions

Hybridizing superconductivity with topology and magnetism attracts growing interest in condensed matter physics. Here, we present our findings on the measurement of supercurrent induced in an intrinsic antiferromagnetic topological insulator MnBi 2 Te 4 . By constructing a MnBi 2 Te 4 proximity Josephson junction, we observed an anomalously large period of the Fraunhofer patterns, indicating a strong Josephson coupling state. As the MnBi 2 Te 4 thickness is reduced, a distinct asymmetric edge supercurrent emerges, aligning consistently with the observed oscillatory junction magnetoresistance. Leveraging this large asymmetric edge supercurrent, we have realized a nonvolatile Josephson diode device with programmable polarity, achieved through training with an out-of-plane magnetic field. Theoretical calculations substantiate that these behaviors are attributed to the interference between the highly asymmetric topological edge channel–mediated supercurrent induced in MnBi 2 Te 4 . Our study establishes this system as a promising avenue for investigating topological superconductivity, chiral Majorana edge modes, and advanced functionality device applications.

Science & Technology - Other Topics↗
DOE OSTI2025

Durable, pure water–fed, anion-exchange membrane electrolyzers through interphase engineering

Anion-exchange membrane water electrolyzers (AEMWEs) promise scalable, low-cost hydrogen production but are limited by the electrochemical instability of their anode ionomers. We report interphase engineering using inorganic-containing molecular additives that coassemble with ionomer, enabling pure water-fed AEMWEs to operate with a degradation rate <0.5 millivolt per hour at 2.0 amperes per square centimeter and 70°C-a >20-fold durability improvement. Analysis of different additives and ionomers shows that the stabilization mechanism involves cross-links between metal oxo/hydroxo oligomers and ionomers. Under operation, the inorganic additive enriches, forming an interphase near the water-oxidation catalyst that passivates the anode ionomer against continuous degradation while maintaining mechanical integrity and hydroxide conductivity. This additive-based interphase-engineering strategy provides a path to durable AEMWEs that operate without supporting electrolytes and is adaptable across diverse catalysts and ionomers for electrochemical technologies.

Hou, Shujin↗
DOE OSTI2024

Preliminary Study of Iodine Gas Removal in Sodium Pools

Potential iodine gas release from failed fuel pins is a critical factor in the source term analysis of oxide fuel-loaded sodium fast reactors (SFRs). The accumulated iodine-containing gas mixtures inside pin plenums are expected to be ejected during pin failures and rise through sodium pool, with potential release of gaseous iodine to the cover gas region. Due to its potential radiological impacts, a proper assessment of iodine behavior is necessary for an accurate source term assessment. Throughout the bubble rise trajectory in the sodium pool, iodine gas is continuously removed or transformed at the bubble interface by diffusion, as the combining reaction between the iodine and sodium to form sodium iodide (NaI) is a chemically preferred process. As the final amount of iodine released from the facility is strongly influenced by the removal phenomenon inside the sodium pool, experiments were previously performed by PNC (Power Reactor and Nuclear Fuel Development Corporation) to provide insight into this phenomenon. To assess the accuracy of present methods for predicting iodine gas removal within sodium pools, several candidate approaches, available in source term analysis codes, have been summarized and evaluated in this study. Spherical cap bubbles and spherical bubbles are considered in accordance with the methods adopted in each approach, and different forms of correlations for major parameters have been implemented in accordance with the original adoptions. Based on the summarized results, important aspects to be considered have been derived.

Decontamination↗
DOE OSTI2026

Community and Passenger Survey Responses for Bastrop, Texas Low-Speed Electric Vehicle Mobility Service Project

This document describes the contents of the following data products: 1. ALL-survey_results_NREL_LiveWire_04_14_2023 (Excel file with two worksheets) 2. eCab_DOE_NREL_LiveWire_04_14_2023_results_all_surveys_except_SP_csv (CSV file) 3. eCab_DOE_NREL_LiveWire_04_14_2023_SP_survey_results_only_csv (CSV file). These data products contain the results of the surveys conducted throughout the DOE-funded Electric First-/Last-Mile On-Demand Shuttle Service for Rural Communities in Central Texas project. The Excel file is the original database of all the survey results (contained in two worksheets). The CSV files are those two worksheets saved as individual CSV files.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

LiMnO2 polymorphs

Energies of LiMnO2 polymorphs computed within various DFT approximations

36 MATERIALS SCIENCE↗