SEARCH · Search NASA
Results for “KRYPTON”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Krypton storage capacity of the Earth's lower mantle
Noble gases are important geochemical tracers allowing reconstructing global volatile cycles in Earth's reservoirs. To constrain these fundamental processes, precise data on their partitioning behavior at deep Earth conditions are needed. Such data are only available at moderate pressures up to 25 GPa due to experimental challenges. We have investigated the possibility of noble gas storage in the Earth's lower mantle up to 115 GPa. We studied the incorporation of krypton in the second most abundant lower mantle mineral (Mg 1-x ,Fe x )O (ferropericlase) as well as in liquid metal-alloys by performing experiments up to 115 GPa and 3700 K using the laser-heated diamond anvil cell coupled to post-mortem EMPA analysis and X-ray absorption spectroscopy. The results reveal that, at these extreme conditions, up to 3 wt.% of krypton can be stored in (Mg 1-x ,Fe x )O and 3000 ppm in the Fe-rich liquid metal. For both phases the storage capacities increase with pressure (between 40 GPa and 60 GPa) at a constant high temperature of 2300 K. Fpc has never been considered as a NG host, despite being the second most abundant mineral in the Earth's LM. Using recent accurate compressibility data, we demonstrate that a substitution of krypton into the anion site of (Mg 1-x ,Fe x )O in form of neutral oxygen Schottky defects at diluted lower mantle conditions is possible. This noble gas incorporation mechanism is in agreement with a previous study on bridgmanite. We show that (Mg 1-x ,Fe x )O exhibits higher noble gas storage capacities than bridgmanite through the lower mantle using lattice strain modeling and including experimental solubility and thermoelastic data for neon, argon, krypton and xenon. We also demonstrate that both phases exhibit the highest solubilities for argon and krypton. We used the solubility data from lattice strain modeling to predict noble gas abundances stored in the solid lower mantle after magma ocean crystallization. The modeled abundances show apparent similarities with estimates for the deep noble gas reservoir that are based on either 3He abundances in ocean island basalts or radiogenic 40Ar abundances in the bulk Earth. This strongly indicates that the crystalline lower mantle may play an important role as deep noble gas storage reservoir. We propose, based on considerations on noble gas replenishment from the lower mantle to the atmosphere, that the lower mantle can only contribute to a small fraction of the present-day atmospheric noble gases. This suggests that the lower mantle is an un-degassed reservoir.
Helium bubble formation in nickel under in-situ krypton and helium ions dual-beam irradiation
Helium has profound effects on the microstructure and mechanical property of materials used in nuclear power systems. Here to understand the interaction between helium and irradiation-induced defects and its effect on bubble formation, single-beam and dual-beam irradiations on nickel were performed with 16 keV helium ions and 1 MeV krypton ions under in-situ TEM observation. For 1 MeV krypton single-beam irradiation, voids were observed at 600ºC but not at 500ºC and 700ºC. For helium single-beam irradiation at 500ºC, helium moved freely and formed bubble-loop complexes. For dual-beam irradiation at 500ºC, helium was trapped by vacancies and formed bubbles homogeneously. The structure of dislocation loops was also affected by the presence of helium. For krypton single-beam irradiation at 500ºC, the microstructure was {100} periodic wall of faulted and perfect dislocation loops. For dual-beam irradiation at 500ºC, periodic wall was not observed, and dislocation loops were predominantly perfect. For single-beam helium at 500ºC, dislocation loops were produced by athermal process of SIAs ejection or loop punching mechanisms. The interplay between helium and vacancies played an important role on the evolution of helium bubbles and defect microstructures.
Kryptonate Hydrogen Detection System (Final Report)
A prototype model of a multipurpose instrument which demonstrates the applicability of the Kryptonate® technique for detecting hydrogen gas was developed. This report describes the construction of the instrument and presents a laboratory evaluation of its performance. Performance was excellent. The instrument was designed to detect hydrogen in air at concentrations of 0-3% by volume, and to detect hydrogen in nitrogen or other inert gas at concentrations of 0-10% by volume. Other detection levels (both higher and lower) could be set if required. Ultimate response times can be made of the order of 0.5 seconds. The instrument is an all solid state device operating from 120V 60 Hz power source. The instrument has been designed to enable modifications to be made with a minimum amount of difficulty.
Harvesting krypton isotopes from the off-gas of an irradiated water target to generate 76Br and 77Br
Abstract A flowing-water target was irradiated with a 150 MeV/nucleon beam of 78 Kr at the National Superconducting Cyclotron Laboratory to produce 77 Kr and 76 Kr. Real-time gamma-imaging measurements revealed the mass transport of the krypton radioisotopes through the target-water processing, or “isotope harvesting”, system. The production rates were determined to be 2.7(1) × 10 –4 nuclei of 76 Kr and 1.18(6) × 10 –2 nuclei of 77 Kr formed per incident 78 Kr ion. Utilizing an off-gas processing line as part of the isotope harvesting system, a total of 7.2(1) MBq of 76 Kr and 19.1(6) MBq of 77 Kr were collected in cold traps. Through the decay, the daughter radionuclides 76 Br and 77 Br were generated and removed from the traps with an average efficiency of 77 ± 12%. Due to the differences in half-lives of 76 Kr and 77 Kr, it was possible to isolate a pure sample of 76 Br with 99.9% radionuclidic purity. The successful collection of krypton radioisotopes to generate 76 Br and 77 Br demonstrates the feasibility of gas-phase isotope harvesting from irradiated accelerator cooling-water. Larger-scale collections are planned for collecting by-product radionuclides from the Facility for Rare Isotope Beams.
Lasing efficiency of krypton ions in the (8 – 14)-nm band upon pulsed laser excitation
The emission spectra of krypton plasma in the range of 8 – 14 nm upon excitation of a pulsed gas jet by 1.06-mm Nd : YAG laser radiation with a pulse energy of 0.85 J, pulse duration of 5.2 ns, and repetition rate of 10 Hz are investigated. The krypton emission spectrum is a wide (8 – 14 nm) band, peaking at 10.3 nm, which is formed by a series of much narrower lines. The observed lines are identified, and the fraction of laser pulse energy converted into the (8 – 14)-nm emission band and emitted into half-space (2π sr) is determined. The maximum conversion efficiency is found to be 21 %. The expected throughputs of lithographic systems with sources based on Sn, Xe, and Kr ions for different wavelengths, corresponding to the emission peaks of ions of these materials, are compared. (paper)
Vacuum-ultraviolet light source for enhanced production of metastable krypton and xenon beams
Here, we demonstrate excitation of metastable krypton and xenon beams using a vacuum ultraviolet lamp and directly compare the performance of this method to metastable excitation based on a radio-frequency-driven plasma discharge. In our apparatus, lamp-based metastable excitation outperforms the plasma discharge across a wide range of beam flux values relevant for atom trap trace analysis (ATTA). Moreover, we do not observe significant degradation in lamp performance after over 160 h of operation. We find that lamp-based excitation is particularly advantageous at the smallest and largest beam fluxes tested, demonstrating the utility of this approach both for improving krypton ATTA and for enabling the detection of radioactive xenon isotopes using ATTA. Finally, we demonstrate an additional enhancement to lamp-based metastable excitation efficiency and stability by applying an external magnetic field.
Krypton Concentration using HZ-PAN
Idaho National Laboratory (INL) has developed and tested engineered sorbents to separate and capture volatile fission products such iodine, xenon (Xe), and krypton (Kr) from off-gas streams. As noble gases, Xe and Kr can be difficult to capture and separate. Historically, cryogenic distillation has been used to execute the separation. However, performing this separation from bulk air streams is expensive and can pose significant hazards. INL has successfully developed two different sorbents for Xe and Kr capture, silver mordenite polyacrylonitrile and hydrogen mordenite polyacrylonitrile (HZ-PAN). Adsorption studies to date successfully separated and captured Kr from carrier gas streams, but those studies focused primarily on initial separation and capture. Successful utilization in a used nuclear fuel (UNF) reprocessing facility, however, requires further concentration of the Kr to minimize long term storage volumes. This study focuses on the concentration of Kr utilizing HZ PAN as the concentrating media. Concentrating Kr during desorption is ideal for two reasons: one, to produce Kr that can be used for commercial and research applications, or two, to minimize the volume of the radioactive gaseous waste stream for disposal. This report investigates the Kr concentrating potential of HZ-PAN by running multiple Kr adsorption-desorption cycles, collecting the desorbed effluent from a saturated HZ-PAN column, and loading it onto a fresh column. This study demonstrates that four adsorption-desorption cycles can transform a 150 ppmv Kr stream into a 37.5% Kr stream, an overall concentration factor of 2497. Each concentration step results in successively smaller volumes desorbed, reducing volume by a factor of approximately 40,000. Depending on the operational goals, during desorption one could collect smaller volume fractions of high concentration Kr (~ 67%). This demonstration should be considered proof-of-concept. Further refinement is necessary to develop optimum operating schemes to integrate into UNF off-gas treatment.
Self-Adjusting Metal–Organic Framework for Efficient Capture of Trace Xenon and Krypton
The capture of the xenon and krypton from nuclear reprocessing off-gas is essential to the treatment of radioactive waste. Although various porous materials have been employed to capture Xe and Kr, the development of high-performance adsorbents capable of trapping Xe/Kr at very low partial pressure as in the nuclear reprocessing off-gas conditions remains challenging. Herein, we report a self-adjusting metal-organic framework based on multiple weak binding interactions to capture trace Xe and Kr from the nuclear reprocessing off-gas. The self-adjusting behavior of ATC-Cu and its mechanism have been visualized by the in-situ single-crystal X-ray diffraction studies and theoretical calculations. The self-adjusting behavior endows ATC-Cu unprecedented uptake capacities of 2.65 and 0.52 mmol g -1 for Xe and Kr respectively at 0.1 bar and 298 K, as well as the record Xe capture capability from the nuclear reprocessing off-gas. Further, our work not only provides a benchmark Xe adsorbent but proposes a new route to construct smart materials for efficient separations.
Supramolecular Assembly of One-Dimensional Coordination Polymers for Efficient Separation of Xenon and Krypton
Efficient separation and purification of xenon (Xe) from krypton (Kr) represent an industrially crucial but challenging process. While the adsorption-based separation of these atomic gases represents an energy-efficient process, achieving highly selective adsorbents remains a difficult task. Here, we demonstrate a supramolecular assembly of coordination polymers, termed as M(II)-dhbq (M = Mg, Mn, Co, and Zn; dhbq = 2,5-dihydroxy-1,4-benzoquinone), with high-density open metal sites (5.3 nm –3 ) and optimal pore size (5.5 Å), which are able to selectively capture Xe among other chemically inert gases including Kr, Ar, N 2 , and O 2 . Among M(II)-dhbq materials, Mn-dhbq exhibits the highest Xe uptake capacity of 3.1 mmol/g and a Xe/Kr selectivity of 11.2 at 298 K and 1.0 bar, outperforming many state-of-the-art adsorbents reported so far. Remarkably, the adsorption selectivity of Mn-dhbq for Xe/O 2 , Xe/N 2 , and Xe/Ar at ambient conditions reaches as high as 70.0, 139.3, and 64.0, respectively. Direct breakthrough experiments further confirm that all M(II)-dhbq materials can efficiently discriminate Xe atoms from other inert gases. Furthermore, it is revealed from the density functional theory calculations that the strong affinity between Xe and the coordination polymer is mainly attributed to the polarization by open metal sites.
Multi-column evaluations for the capture and separation of krypton and xenon using mordenite based sorbents
This presentation is a high-level overview of the research at INL for the capture and separation of krypton and xenon from used nuclear fuel reprocessing off-gas.
Temperature measurements in heavily-sooting ethylene/air flames using synchrotron x-ray fluorescence of krypton
High-fidelity temperature field measurements have been made for several heavily-sooting ethylene/air flames that have historically been challenging environments for conventional optical diagnostics. These challenges have largely been overcome here, in this study, by conducting x-ray fluorescence (XRF) measurements of a Kr fluorescent agent in the hard x-ray regime (15 keV). The current methodology presents a more economical diagnostic than a previously reported implementation of the Kr-XRF method, by limiting seeding of the expensive fluorescent agent to only the fuel stream flows. Detailed reacting flow simulations have been used to interpret experimental signals by tracking the mole fraction of the fluorescent agent in the flow field. Simulated Kr densities are in excellent agreement with measurements throughout the flow field. Temperature measurements of the flow field also agree well with simulations and recent literature studies. However, uncertainties in the measurements become increasingly large downstream of the burner surface as the krypton fraction drops due to mixing of the fuel and co-flow streams. Additionally, we demonstrate that soot particles in the heavily sooting flames studied do not impede the Kr-XRF measurements.
In-situ microstructure observation of oxidized SiC layer in surrogate TRISO fuel particles under krypton ion irradiation
In accidental scenarios of high temperature gas-cooled reactors, both oxidation of and irradiation to the SiC layer in tri-structural-isotropic (TRISO) fuel particles can change the microstructure and integrity of the fuel elements. Here, in the present study, microstructure and defect evolution in the oxidized SiC layer of surrogate TRISO fuel particles under 1.2 MeV krypton ion irradiation was observed by in-situ transmission electron microscopy. The SiC layers oxidized in water vapor at 1200 °C were irradiated azt room temperature and 800 °C and at damage levels of 0.28–11.2 dpa, respectively. SiC and SiO 2 were found to still be in their crystal structures at the damage level of 11.2 dpa at 800 °C, while SiC was observed to have been amorphized at only 0.56 dpa irradiation at room temperature. The defect number density at 800 °C was an order of magnitude lower than that in the sample irradiated at room temperature. Also, crystalline SiO 2 had higher radiation resistance compared to SiC. A defect reaction rate theory was utilized to understand the fundamental defect evolution process and irradiation resistance difference.
Unraveling the Early-Stage Ordering of Krypton Solid Bubbles in Molybdenum: A Multimodal Study
Self-organization of defects such as fission gas bubbles in materials can lead to high inventory capacity for fission gas storage and help mitigate swelling caused by fission gases in nuclear fuel materials under radiation in nuclear reactors. Here, we report the physical mechanism of self-organization of krypton (Kr) gas bubbles in molybdenum (Mo) under ion implantation. The ion fluence and temperature-dependent formation of Kr solid bubble superlattice (SBS) in Mo were investigated by using both synchrotron-based small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). Early stage self-organization of gas bubbles is observed at a fluence of 2.5 × 10 16 ions/cm 2 at temperatures of 300–400 °C. The bubble lattice constant increases with increasing implantation temperature from 300 to 400 °C. Both experiments and atomic kinetic Monte Carlo modeling indicate that the Kr solid bubbles are weakly ordered in comparison to previously studied helium (He) gas bubble superlattice (GBS) while the lattice constant are relatively smaller for Kr SBS compared to that of He GBS. The irradiation conditions suggest that spinodal decomposition, which is a form of phase separation, probably precedes gas bubble ordering in Mo. Altogether, our work sheds light on the formation mechanism of noble gas superlattice toward the development of radiation-tolerant materials which are important for the design of advanced nuclear reactors.
Adsorption Studies of Dilute Krypton and Xenon from Nitrogen on SBMOF-1 and Activated Charcoal for Applications in Isotope Harvesting
Adsorptive partitioning of dilute krypton (Kr) and xenon (Xe) onto Stony Brook Metal–Organic Framework (SBMOF-1) and activated charcoal (AC) from carrier nitrogen was experimentally measured at temperatures ranging from 195 to 293 K. For this purpose, a closed-loop system for gas adsorption experiments was developed. From the Kr adsorption measurements, the adsorption equilibrium constant for Kr on SBMOF-1 was calculated, yielding a value for the enthalpy of adsorption of −19 ± 1 kJ·mol –1 . The partition coefficients were utilized to estimate the extraction rates of 76 Kr, 77 Kr, and 122 Xe isotopes during isotope harvesting at the Facility for Rare Isotope Beams (FRIB). We conclude that both materials showed promising results for the extraction of noble gases from FRIB effluents using temperature swing adsorption.
Radiation-resistant metal-organic framework enables efficient separation of krypton fission gas from spent nuclear fuel
Capture and storage of volatile radionuclides that result from processing of used nuclear fuel is a major challenge. Solid adsorbents, in particular ultra-microporous metal-organic frameworks, could be effective in capturing these volatile radionuclides, including 85 Kr. However, metal-organic frameworks are found to have higher affinity for xenon than for krypton, and have comparable affinity for Kr and N 2 . Also, the adsorbent needs to have high radiation stability. To address these challenges, here we evaluate a series of ultra-microporous metal-organic frameworks, SIFSIX-3-M (M = Zn, Cu, Ni, Co, or Fe) for their capability in 85 Kr separation and storage using a two-bed breakthrough method. These materials were found to have higher Kr/N 2 selectivity than current benchmark materials, which leads to a notable decrease in the nuclear waste volume. The materials were systematically studied for gamma and beta irradiation stability, and SIFSIX-3-Cu is found to be the most radiation resistant.
Measuring sub-surface spatially varying thermal conductivity of silicon implanted with krypton
The thermal properties of semiconductors following exposure to ion irradiation are of great interest for the cooling of electronic devices; however, gradients in composition and structure due to irradiation often make the measurement difficult. Furthermore, the nature of spatial variations in thermal resistances due to spatially varying ion irradiation damage is not well understood. In this work, we develop an advancement in the analysis of time-domain thermoreflectance to account for spatially varying thermal conductivity in a material resulting from a spatial distribution of defects. We then use this method to measure the near-surface (≲1 μm) thermal conductivity of silicon wafers irradiated with Kr + ions, which has an approximate Gaussian distribution centered 260 nm into the sample. Our numerical analysis presented here allows for the spatial gradient of thermal conductivity to be extracted via what is fundamentally a volumetric measurement technique. We validate our findings via transmission electron microscopy, which is able to confirm the spatial variation of the sub-surface silicon structure, and provide additional insight into the local structure resulting from the effects of ion bombardment. Thermal measurements found the ion stopping region to have a nearly 50x reduction in thermal conductivity as compared to pristine silicon, while TEM showed the region was not fully amorphized. Our results suggest this drastic reduction in silicon thermal conductivity is primarily driven by structural defects in crystalline regions along with boundary scattering between amorphous and crystalline regions, with a negligible contribution being due to implanted krypton ions themselves.
Study of Stark broadening of krypton helium-$\beta$ lines and estimation of electron density and temperature in NIF compressed capsules
Here the National Ignition Facility (NIF) diagnostic instrument manipulator (DIM) - based high resolution (dHIRES) x-ray spectrometer was used to measure the time evolution of the electron density (n e ) and temperature (T e ) in the hot spot of four NIF compressed capsules with 25 ps time resolution during the 'stagnation' phase. The electron density was inferred by comparing the measured Stark broadening of the krypton (Kr) Heβ spectral complex with theoretical calculations that include ion dynamic effects, and the electron temperature was inferred by comparing the measured ratio of the intensity of a dielectronically excited Li-like Kr line to the intensity of the Kr Heβ resonance line with calculations using the spectroscopic collisional radiative atomic model (SCRAM) and CRETIN collisional-radiative models. The inferred, time averaged n e values mainly agree with n e values from neutron diagnostics within uncertainties, but the neutron time-of-flight values of T ion are consistently higher than dHIRES T e values by 200–700 eV. The dHIRES measurements and measurement techniques, method of uncertainty analysis, and discussion of comparisons with measurements from neutron diagnostics are presented.