SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The design, fabrication, and testing of two types of IMPATT diode reflection amplifiers and a transmission amplifier are given. The Ku-band IMPATT diode development is discussed. Circuitry and electrical performance of the final version of the Ku-band amplifier is described. Construction details and an outline and mounting drawing are presented.
Ku-band microminiature modulators were designed to convert a 10 mW signal at 400 MHz to a 10 mW signal at 15 GHz. The designs incorporate gallium arsenide Schottky barrier varactors used in upper-sideband up-converters. The use of Ku-band microstrip circulators and hairpin resonator bandpass filters at 2.1 GHz and 2.5 GHz is included. The design and fabrication of a single up-conversion unit with a double up-conversion unit are compared. Various filter configurations are studies, and the use of both alumina and quartz substrates are considered. The various impedance matching networks are evaluated using computer aided design techniques.
An exposed four element array of 12.8 m diameter elements mounted on a common pedestal is the recommended ground antenna configuration in support of the 2 GHz bandwidth Ku-band downlink from tdr satellites. The array provides three channel phase monopulse tracking capability with only listening feeds in each element. The array is as cost effective as a single aperture antenna and offers significant advantages in tracking and reliability.
The construction of a Ku-band radio interferometer and some preliminary observations are reported. The interferometer was built for the purpose of mapping discrete radio sources like the Crab Nebula, Cassiopeia A, and Cygnus A. It has two 8-ft parabolic antennas operating at 17.128 GHz. The maximum baseline of 100 m corresponds to a resolution of 35 sec of arc. A PDP-8 computer is incorporated in the system and is used for pointing, tracking, delay compensation, and real-time data analysis. The phase stability of the system was better than 10 deg over a period of 2 hours. Consistent fringe components were obtained from the Crab Nebula with a baseline set at 8 m.
Antenna systems for a Ku-band synchronous orbit communications satellite were considered. A multiple beam offset feed cluster used in conjunction with an offset parabolic reflector was chosen for the antenna realization. For radiating elements in the feed array, polyrod or dielectric rod radiators fed by waveguide are investigated. Polyrod antennas shrink the cross section of the waveguide required, are fairly directive, and can be tapered to reduce sidelobes. As a consequence, it is thought that mutual coupling effects between adjacent elements will be minimal and the resultant physically small elements will allow greater packing densities for the drive elements in the feed array than would otherwise be possible.
A superconducting magnet to provide a uniform magnetic field of up to 8000 G in a 1.14-cm gap for the 15.3-GHz (Ku-band) traveling wave maser is described. The magnet operates in a persistent mode in the vacuum environment of a closed-cycle helium refrigerator (4.5 K). The features of a superconducting switch, which has both leads connected to 4.5 K heat stations and thereby does not receive heat generated by the magnet charging leads, are described.
High power transferred electron effect devices for superhigh frequency oscillators
Low loss low sidelobe N-way microwave optical power divider for single plane electronically steerable Ku band phased array antenna
Systems engineering and economic analysis of tracking and data relay satellite system with 16 GHz ground antenna
Construction of Ku band radio interferometer and preliminary observations
A proposed solid-state K sub u-band power amplifier utilizing a circularly symmetric array of IMPATT diodes mounted in a single radial line power combiner is discussed and its performance predicted. The proposed amplifier configuration consists of a TM sub 030 mode radial line cavity containing 20 IMPATT diodes, with separate input and output ports provided by a ferrite circulator. Conventional IMPATT amplifier techniques preclude the achievement of gain, power output, efficiency, and IMP suppression specifications simultaneously; there fore, several novel techniques with the potential of reducing the intermodulation product level are discussed.
The author has identified the following significant results. The Skylab S-193 radiometer/scatterometer collected thousands of measurements of scattering coefficient and brightness temperature over various parts of the United States during the summer of 1973 at angles of incidence between vertical and about 45 deg. These measurements have been combined to produce histograms of the response at each of several angles within this range, and to establish average scattering coefficient vs angle curves with 10% and 90% exceedance levels as well. The variation of the radiometric measurements is primarily in the region from 255 K to 285 K, with very few measurements giving higher values, but a significant, though small, number giving values down to and even below 200 K. The scattering coefficient varies, for the mean, from about 0 db at 1 deg off vertical to a low in the neighborhood of -10 db at 45 deg. The variability of the scattering coefficient measurements with this coarse resolution sensor is surprisingly small. The number of distinguishable levels is slightly more for the scatterometer than for the radiometer, but the amount of variation in brightness temperature caused by the physical temperature of the ground is enough so that the scatterometer can be used to distinguish significantly more meaningful levels than the radiometer.
SeaSat-A Satellite Scatterometer (SASS) measurements of normalized radar cross section (NRCS) have been merged with high quality surface-wind fields based on in situ, to create a large data base of NRCS-wind signature data. These data are compared to the existing NRCS-wind model used by the SASS to infer winds. Falso-color maps of SASS NRCS and ocean winds from multiple orbits show important synoptic trends.
Analysis and evaluation of critical components of Ku-band phased array antenna for meteorological satellite
A 1.83-m diameter furlable conical Gregorian antenna based on a novel spoke-supported ring-membrane concept has been successfully demonstrated. Mechanical measurements of the conical reflecting surface, as well as BE gain measurements at Ku-band, show an rms surface deviation from the proper conical surface of 0.3 mm and a repeatability after multiple furling-unfurling cycles of + or - 0.05 mm. Design features and performance characteristics of this antenna indicate that the spoke-supported ring-membrane concept is a promising approach for producing large, furlable, lightweight, conical reflectors for spacecraft high-gain antennas.
Recent activities at JPL directed toward the development of large furlable spacecraft antennas using conical main reflectors are described. Development of two basic antenna configurations conceived at JPL and utilizing conical main reflectors was pursued. A 4.3-m (14-ft)-diameter model based on the two-reflection conical-Gregorian concept and a 1.8-m (6-ft)-diameter model based on the four-reflection Quadreflex concept have been made and RF-tested. RF gain measurements for the 4.3-m (14-ft)-diameter conical-Gregorian model were 48.83 db at X-band (8.448 GHz) and 37.82 db at S-band (2.297 GHz). These gains correspond to efficiencies of 53.6 and 57.5%, respectively. RF gain measurements for the 1.8-m (6-ft)-diameter Quadreflex model were 47.59 db at Ku-band (16.33 GHz) and 41.30 db at X-band (8.448 GHz), corresponding to efficiencies of 58.6 and 51.5%, respectively.
Design concepts for high temperature flush mounted Space Shuttle Orbiter antenna systems are discussed. The design concepts include antenna systems for VHF, L-band, S-band, C-band and Ku-band frequencies. The S-band antenna system design was completed and test hardware fabricated. It was then subjected to electrical and thermal testing to establish design requirements and determine reuse capabilities. The thermal tests consisted of applying ten high temperature cycles simulating the Orbiter entry heating environment in an arc tunnel plasma facility and observing the temperature distributions. Radiation pattern and impedance measurements before and after high temperature exposure were used to evaluated the antenna systems performance. Alternate window design concepts are considered. Layout drawings, supported by thermal and strength analyses, are given for each of the antenna system designs. The results of the electrical and thermal testing of the S-band antenna system are given.
The principal features of this document are the analysis of a large dual-reflector antenna system by vector Kirchhoff theory, the evaluation of subreflector aperture-blocking, determination of the diffraction and blockage effects of a subreflector mounting structure, and an estimate of strut-blockage effects. Most of the computations are for a frequency of 15.3 GHz, and were carried out using the IBM 360/91 and 360/95 systems at Goddard Space Flight Center. The FORTRAN 4 computer program used to perform the computations is of a general and modular type so that various system parameters such as frequency, eccentricity, diameter, focal-length, etc. can be varied at will. The parameters of the 60-foot NRL Ku-band installation at Waldorf, Maryland, were entered into the program for purposes of this report. Similar calculations could be performed for the NELC installation at La Posta, California, the NASA Wallops Station facility in Virginia, and other antenna systems, by a simple change in IBM control cards. A comparison is made between secondary radiation patterns of the NRL antenna measured by DOD Satellite and those obtained by analytical/numerical methods at a frequency of 7.3 GHz.