SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The improvement of airplanes and increased safety of air traffic can be sought in various ways. In the experiments described below, the aim was to find some simple and inexpensive method of modifying present-day airplanes, so as to improve and simplify the process of landing.
Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact. Landings made at abnormally low trims led to unusually severe bounces during the runout. The least severe landing occurred after a small lending when the model was rapidly decelerated at about 0.4 g in a simulation of the proposed use of braking devices. The severity of the landings increased with wave height and was at a maximum when the wave length was of the order of from one and one-half to twice the over-all length of the model. The models with afterbodies of moderate length frequently bounced clear of the water into a stalled attitude at speeds below flying speed. The model with the long afterbody had less tendency to bounce from the waves and consequently showed less severe accelerations during the landing run than the models with moderate lengths of afterbody.
Explore the source record for details and available documents.
An investigation of a 1/14-scale dynamically similar model of the Northrop C-125 airplane was made to determine the ditching characteristics and proper ditching technique for the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. It was concluded that the airplane should be ditched at a nose-high landing attitude (near 8 deg) with flaps full down. The fixed landing gear will cause the airplane to dive. The fuselage will be damaged and will probably flood rapidly. Longitudinal decelerations will be about 4g and the length of landing run will be about two fuselage lengths. If the main landing gear could be jettisonable or retractable the ditching characteristics would be greatly improved.
Full-scale wind-tunnel and flight tests were made of a Fairchild 22 airplane equipped with a Fowler flap to determine the effect of the flap on the performance and control characteristics of the airplane. In the wind-tunnel tests of the airplane with the horizontal tail surfaces removed, the flap was found to increase the maximum lift coefficient from 1.27 to 2.41. In the flight test, the flap was found to decrease the minimum speed from 58.8 to 44.4 miles per hour. The required take-off run to attain an altitude of 50 feet was reduced from 935 feet to 700 feet by the use of the flap, the minimum distance being obtained with five-sixths full deflection. The landing run from a height of 50 feet was reduced one-third. The longitudinal and directional control was adversely affected by the flap, indicating that the design of the tail surfaces is more critical with a flapped than a plain wing.
This investigation was intended to throw light on a number of problems: 1) obtain a time history of the force acting on the gear wheels during take-off and landing runs; 2) obtain the time history of the direction of this force (magnitude of its three components along the coordinate axes); 3) derive conclusions as to the design load factors. In connection with the latter, of special interest was the solution of such problems as: a) the dynamic loads in the three main landing attitudes; b) the problem of the true direction of the forces for each of the three "pure" types of landing; c) combination of the above types; d) the comparison for each of the chassis members of the computed force (according to the design standards) with the actual force measured in the tests so as to determine the actual factors of safety.
General considerations concerning the design of a new aircraft are discussed, taking into account the objective to develop an aircraft can satisfy economically a certain spectrum of tasks. Requirements related to the design of sport and touring aircraft included in the past mainly a high cruising speed and short take-off and landing runs. Additional requirements for new aircraft are now low fuel consumption and optimal efficiency. A computer program for the computation of flight performance makes it possible to vary automatically a number of parameters, such as flight altitude, wing area, and wing span. The appropriate design characteristics are to a large extent determined by the selection of the flight altitude. Three different wing profiles are compared. Potential improvements with respect to the performance of the aircraft and its efficiency are related to the use of fiber composites, the employment of better propeller profiles, more efficient engines, and the utilization of suitable instrumentation for optimal flight conduction.
Advanced flight control system design, analysis, and testing methodologies developed at the Ames Research Center are applied in an analytical and flight test evaluation of the Advanced Digital Optical Control System (ADOCS) demonstrator. The primary objectives are to describe the knowledge gained about the implications of digital flight control system design for rotorcraft, and to illustrate the analysis of the resulting handling-qualities in the context of the proposed new handling-qualities specification for rotorcraft. Topics covered in-depth are digital flight control design and analysis methods, flight testing techniques, ADOCS handling-qualities evaluation results, and correlation of flight test results with analytical models and the proposed handling-qualities specification. The evaluation of the ADOCS demonstrator indicates desirable response characteristics based on equivalent damping and frequency, but undersirably large effective time-delays (exceeding 240 m sec in all axes). Piloted handling-qualities are found to be desirable or adequate for all low, medium, and high pilot gain tasks; but handling-qualities are inadequate for ultra-high gain tasks such as slope and running landings.
NASA and the FAA have conducted a brief flight-test investigation to furnish preliminary data on the feasibility of transport aircraft wake-vortices' detection, with a view to improving airport capacity by reducing the longitudinal in-trail spacing between aircraft on landing runs. Attention was given to the possibility that the detection of strong vortices at a sufficiently early stage might furnish reasonable warning of impending aerodynamic effects. Preliminary results indicate that while maximum detection distances obtainable with wingtip-mounted flow-angularity vanes are slightly lower than had been predicted, improved detector algorithms may render them more sensitive.
This paper discusses implications of digital flight control system design for rotorcraft and illustrates the analysis of the resulting handling qualities obtained with the Advanced Digital Optical Control System demonstrator in the context of the proposed new handling-qualities specification for rotorcraft. Topics covered are digital flight control design and analysis methods, flight testing techniques, handling-qualities evaluation results, and correlation of flight test results with analytical models and the proposed handling-qualities specification. The evaluation of the demonstrator system indicates desirable response characteristics based on equivalent damping and frequency, but undersirably large effective time delays (exceeding 240 ms in all axes). Piloted handling qualities are found to be desirable or adequate for all low, medium, and high pilot gain tasks, but handling qualities are inadequate for ultrahigh gain tasks such as slope and running landings. Correlation of these results with the proposed handling-qualities specification indicates good agreement for the bandwidth boundaries, but suggests the need for more stringent limits on allowable phase delay. Analytical models based on emulation (s-plane) techniques compare favorably with flight-extracted frequency-domain characteristics of the overall (end-to-end) system responses.
The results of tests to determine the effect of wheel brakes on the landing run of an airplane under conditions of load and at various wind velocities are presented.
An investigation was conducted to obtain information on the tire-to-surface friction coefficients available in aircraft braking during the landing run. The tests were made with a C-123B airplane on both wet and dry concrete and bituminous pavements and on snow-covered and ice surfaces at speeds from 12 to 115 knots. Measurements were made of the maximum (incipient skidding) friction coefficient, the full-skidding (locked wheel) friction coefficient, and the wheel slip ratio during braking.
A supplementary investigation of a 1/18-scale dynamically similar model of the North American B-45 airplane was made in calm water to observe the ditching behavior and to determine the effect of further conditions of simulated damage. The behavior of the model was determined from motion-picture records, time-history deceleration records, and visual observations. It was concluded that, during a ditching, the nose-wheel doors, bomb-bay doors, under surface of the aft fuselage and lower part of the bomb-bay aft bulkhead will be torn away. When such damage occurs, the diving found in the previous tests will not occur and the airplane will porpoise during the first third of the landing run and then run smoothly. Because of the extensive damage which occurs, the fuselage aft of the pilots' compartment will fill with water very rapidly and is, therefore, an undesirable ditching station. No change in the previously recommended ditching attitude and flap setting (6 deg attitude, flaps down) is indicated by these supplementary tests.
Explore the source record for details and available documents.
Ground-run tests with bogie-type landing gear on water and slush covered runways
Explore the source record for details and available documents.
The vertical force-deflection characteristics were experimentally determined for a pair of 56-inch-diameter tires under static and drop-test conditions with and without prerotation. For increasing force, the tires were found to be least stiff for static tests, almost the same as for the static case for prerotation drop tests as long as the tires remain rotating, and appreciably stiffer for drop tests without prerotation.
A basic theoretical and experimental investigation is made of the shimmy behavior of a swiveling landing gear, the experimental tests being conducted with a small wheel mounted over a continuous belt. Effects of wheel loading, rolling velocity, rearward position of the wheel with respect to the swivel axis, tire elasticity, and torsional flexibility of the fuselage are investigated both experimentally and theoretically. A major theoretical conclusion is that the motion of a landing gear moving in a straight line without fuselage elasticity is stable for a sufficiently large rearward position of the wheel behind the swivel axis, and this conclusion is well verified quantitatively by the experimental data.