Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIFT DISTRIBUTION - WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1935

Method for the determination of the spanwise lift distribution

The method for determination of the spanwise lift distribution is based on the Fourier series for the representation of the lift distribution. The lift distribution, as well as the angle of attack, is split up in four elementary distributions. The insertion of the angle-of-attack distribution in the Fourier series for the lift distribution gives a compound third series which is of particular advantage for the determination of the lift distribution. The method is illustrated in an example and supplemented by a graphical method. Lastly, the results of several comparative calculations with other methods are reported.

Lippisch, A↗
NASA NTRS1931

Lift distribution and longitudinal stability of an airplane

The preliminary calculation of the airplane polar and hence of the flight performances and characteristics rests on the assumption of an elliptical lift distribution at all altitudes. For large angles of attack below C(sub a (sub max)), this method of calculation yields no satisfactory agreement with measurements made in flight. An attempt is made to eliminate the errors in the preliminary calculation by the assumption of a disturbance of the lift distribution in this angle-of-attack range, which is so important for the constructor. An explanation is also given of the great differences found in flight with and without propeller slipstream.

Topfer, Carl↗
NASA NTRS1977

Effects of lengthwise lift distribution on sonic boom of SST configurations

Sonic Boom signatures produced by possible SST configurations during cruise were investigated. It is shown that optimization based on a far field analysis is not necessarily the optimum for these conditions. For an airplane length of 300 ft, near-field effects can be obtained when sufficient lift is generated near the nose of the airplane. Because of the near-field effects, sonic booms with maximum overpressures of the order of 1 lb/square foot can be obtained with possible airplane configurations having the same flight conditions at cruise.

Ferri, A.↗
NASA NTRS1976

Historical review of C-5A lift distribution control systems

Analytical and experimental development work on various load alleviation systems for the C-5A is reviewed to trace the development of the technical and hardware concepts to the present time. Variations in system objectives, means of implementation and effects on loads and airplane performance, stability and control are discussed.

Disney, T. E.↗
NASA NTRS1976

The C-5A active lift distribution control system

The ALDCS development and design tasks, ALDCS functional configuration, and resulting challenges encountered while accomplishing the first phase of the program are described. These tasks are establishing system requirements and criteria and synthesizing a system mechanization to meet the desired load alleviation, stability margins, flight safety, and flying qualities performance. Results of the ALDCS development and prototype system flight simulation programs, and control law optimization including system stability, handling qualities and structural load analyses are presented, along with concluding remarks relative to the system design integration.

Hargrove, W. J.↗
NASA NTRS1974

Aerodynamic design of a rotor blade for minimum noise radiation

An analysis of the aerodynamic design of a hovering rotor blade for obtaining minimum aerodynamic rotor noise has been carried out. In this analysis, which is based on both acoustical and aerodynamic considerations, attention is given only to the rotational noise due to the pressure fluctuations on the blade surfaces. The lift distribution obtained in this analysis has different characteristics from those of the conventional distribution. The present distribution shows negative lift values over a quarter of the span from the blade tip, and a maximum lift at about the midspan. Results are presented to show that the noise field is considerably affected by the shape of the lift distribution along the blade and that noise reduction of about 5 dB may be obtained by designing the rotor blade to yield minimum noise.

Karamcheti, K.↗
NASA NTRS2010

Use of ILTV Control Laws for LaNCETS Flight Research

A report discusses the Lift and Nozzle Change Effects on Tail Shock (LaNCETS) test to investigate the effects of lift distribution and nozzle-area ratio changes on tail shock strength of an F-15 aircraft. Specific research objectives are to obtain inflight shock strength for multiple combinations of nozzle-area ratio and lift distribution; compare results with preflight prediction tools; and update predictive tools with flight results. The objectives from a stability and control perspective are to ensure adequate aircraft stability for the changes in lift distribution and plume shape, and ensure manageable transient from engaging and disengaging the ILTV research control laws. In order to change the lift distribution and plume shape of the F-15 aircraft, a decade-old Inner Loop Thrust Vectoring (ILTV) research control law was used. Flight envelope expansion was performed for the test configuration and flight conditions prior to the probing test points. The approach for achieving the research objectives was to utilize the unique capabilities of NASA's NF-15B-837 aircraft to allow the adjustment of the nozzle-area ratio and/or canard positions by engaging the ILTV research control laws. The ILTV control laws provide the ability to add trim command biases to canard positions, nozzle area ratios, and thrust vectoring through the use of datasets. Datasets consist of programmed test inputs (PTIs) that define trims to change the nozzle-area ratio and/or canard positions. The trims are applied as increments to the normally commanded positions. A LaNCETS non-linear, six-degrees-of-freedom simulation capable of realtime pilot-in-the-loop, hardware-in-the-loop, and non-real-time batch support was developed and validated. Prior to first flight, extensive simulation analyses were performed to show adequate stability margins with the changes in lift distribution and plume shape. Additionally, engagement/disengagement transient analysis was also performed to show manageable transients.

Moua, Cheng↗
NASA NTRS1931

A proof of the theorem regarding the distribution of lift over the span for minimum induced drag

The proof of the theorem that the elliptical distribution of lift over the span is that which will give rise to the minimum induced drag has been given in a variety of ways, generally speaking too difficult to be readily followed by the graduate of the average good technical school of the present day. In the form of proof this report makes an effort to bring the matter more readily within the grasp of this class of readers.

Durand, W F↗
NASA NTRS1953

Comparison of the Experimental and Theoretical Distribution of Lift on a Slender Inclined Body of Revolution at M = 2

Pressure distributions and force characteristics have been determined for a body of revolution consisting of a fineness ratio 5.75, circular-arc, ogival nose tangent to a cylindrical afterbody for an angle-of-attack range of 0 degrees to 35.5 degrees. The free-stream Mach number was 1.98 and the free-stream Reynolds number was approximately 0.5 x 10 sup 6, based on body diameter. Comparison of the theoretical and experimental pressure distributions shows that for zero lift, either slender-body theory or higher-order theories yield results which are in good agreement with experiment. For the lifting case, good agreement with theory is found only for low angles of attack and for the region in which the body cross-sectional area is increasing in the downstream direction. Because of the effects of cross-flow separation and the effects of compressibility due to the high cross-flow Mach numbers at large angles of attack, the experimental pressure distributions differ from those predicted by potential theory. Although the flow about the inclined body was, in general, similar to that assumed as the basis for Allen's method of estimating the forces resulting from viscous effects (NACA RM A91I26), the distribution of the forces was significantly different from that assumed. Nevertheless, the lift and pitching-moment characteristics were in fair agreement with the estimated value.

Perkins, Edward W↗
NASA NTRS1985

Application of two-dimensional unsteady aerodynamic to a free-tip rotor response analysis

The free-tip rotor utilizes a rotor blade tip which is structurally decoupled from the blade inboard section. The tip is free to pitch about its own pitch axis to respond to the local flow angularity changes. The tip also experiences the heaving motion due to the flapping of the rotor blade. For an airfoil in any pitching and heaving motion which can be expanded into a Fourier series, the lift and moment calculated by Theodoren's theory is simply the linear combination of the lift and moment calculated for each harmonic. These lift and moment are then used to determine the response of the free-tip rotor. A parametric study is performed to determine the effect of mechanical damping, mechanical spring, sweep, friction, and a constant control moment on the free-tip rotor response characteristics and the resulting azimuthal lift distributions. The results showed that the free-tip has the capability to suppress the oscillatory lift distribution around the azimuth and to eliminate a significant negative life peak on the advancing tip. This result agrees with the result of the previous analysis based on the steady aerodynamics.

Yates, L.↗
NASA NTRS2010

Challenges and Lessons Learned From Resurrecting a Legacy Research Flight Controller

Resurrecting the legacy Inner Loop Thrust Vectoring research flight controller to investigate the tail shock region brought unique challenges. This report documents these challenges and lessons learned from a stability and controls perspective. The flight test approach for flight envelope expansion and probing tests, as well as limited flight test results, are presented. Recent advances in sonic boom reduction technology have contributed to a resurgent interest in civilian supersonic cruise flight. These advances have focused only on fore body shaping, however, and little, if any, experimental flight data are available to develop and validate design tools for the tail shock region. In January of 2009, the NASA Dryden Flight Research Center completed research flights to investigate the tail shock region of a highly modified F-15 aircraft by probing the shock waves around it, using another F-15 aircraft. To adjust the lift distribution and plume shape, a decade-old research flight controller from the Inner Loop Thrust Vectoring project was required. To investigate the tail shock region, the lift distribution was changed by adjusting the canard position, and the plume shape was changed by adjusting the nozzle area and thrust vectoring.

Dees, Ray A.↗
NASA NTRS2008

Overview of the LaNCETS Flight Experiment and CFD Analysis. Supplemental Movies

This presentation focuses on nearfield airborne pressure signatures from the Lift and Nozzle Change Effect on Tail Shocks (LaNCETS) flight test experiment. The primary motivation for nearfield probing in the supersonic regime is to measure the shock structure of aircraft in an ongoing effort to overcome the overland sonic boom barrier for commercial supersonic transportation. LaNCETS provides the opportunity to investigate lift distribution and engine plume effects. During Phase 1 flight testing an F-15B was used to probe the F-15 LaNCETS aircraft in order to validate CFD and pre-flight prediction tools. A total of 29 probings were taken at 40,000 ft. altitude at Machs 1.2, 1.4 and 1.6. LaNCETS Phase 1 flight data are presented as a detailed pressure signature superimposed over a picture of the LaNCETS aircraft. The attenuation of the Inlet-Canard shocks with distance as well as its forward propagation and the coalescence of the noseboom shock are illustrated. A detailed CFD study on a simplified LaNCETS aircraft jet nozzle was performed providing the ability to more accurately capture the shocks from the propulsion system and emphasizing how under- and over-expanding the nozzle affects the existence of shock trains inside the jet plume. With Phase 1 being a success preparations are being made to move forward to Phase 2. Phase 2 will fly similar flight conditions, but this time changing the aircraft's lift distribution by biasing the canard positions, and changing the plume shape by under- and over-expanding the nozzle. Nearfield probing will again be completed in the same manner as in Phase 1. An additional presentation focuses on LaNCETS CFD solution methodology. Discussions highlight grid preprocessing, grid shearing and stretching, flow solving and contour plots. Efforts are underway to better capture the flow features via grid modification and flow solution methodology, which will help to achieve better agreement with flight data. An included CD-ROM provides animations of the nearfield probing procedure and of real data from one of the probings integrated with GPS positional and velocity data. An additional in-flight video from the rear seat of the probing aircraft is also provided.

Cliatt, Larry J., II↗
NASA NTRS1986

Verification of performance results for a low-speed 15 percent elliptical circulation control airfoil

Low-speed wind tunnel tests performed by the Naval Ship Research and Development Center (NSRDC) on a circulation control airfoil model was repeated by the Joint Institute for Aerodynamics and Acoustics in an attempt to reproduce the performance results. The model used was a 15% ellipse with interchangeable trailing edges. Surface pressure measurements were taken to obtain lift and pitching moment coefficients as functions of jet blowing momentum, and the momentum deficit in the wake was measured and used to calculate the drag coefficient. The effects of spanwise slot height variation and of leading edge blowing on performance were also investigated. The performance results showed that of the three slot heights tested, a slot height/chord ratio of 0.0022 produced the most lift coefficient for a given blowing rate. Lift obtained in the current test ranged from 2 to 35% lower than the NSRDC test. However, the two data sets compared reasonably well considering wind tunnel and wall blowing scheme differences. The spanwise lift distribution showed less change in lift due to a variation in slot height than expected. The leading edge blowing results demonstrated that although lift initially decreased, a positive lift increment was possible at higher leading edge blowing rates.

Rodman, L. C.↗