Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIFTING REENTRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

In-Flight Subsonic Lift and Drag Characteristics Unique to Blunt-Based Lifting Reentry Vehicles

Lift and drag measurements have been analyzed for subsonic flight conditions for seven blunt-based reentry-type vehicles. Five of the vehicles are lifting bodies (M2-F1, M2-F2, HL-10, X-24A, and X-24B) and two are wing-body configurations (the X-15 and the Space Shuttle Enterprise). Base pressure measurements indicate that the base drag for full-scale vehicles is approximately three times greater than predicted by Hoerner's equation for three-dimensional bodies. Base drag and forebody drag combine to provide an optimal overall minimum drag (a drag "bucket") for a given configuration. The magnitude of this optimal drag, as well as the associated forebody drag, is dependent on the ratio of base area to vehicle wetted area. Counter-intuitively, the flight-determined optimal minimum drag does not occur at the point of minimum forebody drag, but at a higher forebody drag value. It was also found that the chosen definition for reference area for lift parameters should include the projection of planform area ahead of the wing trailing edge (i.e., forebody plus wing). Results are assembled collectively to provide a greater understanding of this class of vehicles than would occur by considering them individually.

Saltzman, Edwin J.↗
NASA NTRS1978

Comparison of concurrent strain gage- and pressure transducer-measured flight loads on a lifting reentry vehicle and correlation with wind tunnel predictions

Concurrent strain gage and pressure transducer measured flight loads on a lifting reentry vehicle are compared and correlated with wind tunnel-predicted loads. Subsonic, transonic, and supersonic aerodynamic loads are presented for the left fin and control surfaces of the X-24B lifting reentry vehicle. Typical left fin pressure distributions are shown. The effects of variations in angle of attack, angle of sideslip, and Mach number on the left fin loads and rudder hinge moments are presented in coefficient form. Also presented are the effects of variations in angle of attack and Mach number on the upper flap, lower flap, and aileron hinge-moment coefficients. The effects of variations in lower flap hinge moments due to changes in lower flap deflection and Mach number are presented in terms of coefficient slopes.

Tang, M. H.↗
NASA NTRS1984

Aerodynamic characteristics of some lifting reentry concepts applicable to transatmospheric vehicle design studies

The aerodynamic characteristics of some lifting reentry concepts are examined with a view to the applicability of such concepts to the design of possible transatmospheric vehicles (TAV). A considerable amount of research has been done in past years with vehicle concepts suitable for manned atmospheric-entry, atmospheric flight, and landing. Some of the features of these concepts that permit flight in or out of the atmosphere with maneuver capability should be useful in the mission requirements of TAV's. The concepts illustrated include some hypersonic-body shapes with and without variable geometry surfaces, and a blunt lifting-body configuration. The merits of these concepts relative to the aerodynamic behavior of a TAV are discussed.

Spearman, M. L.↗
NASA NTRS1984

Aerodynamic characteristics of some lifting reentry concepts applicable to transatmospheric vehicle design studies

The aerodynamic characteristics of some lifting reentry concepts are examined with a view to the applicability of such concepts to the design of possible transatmospheric vehicles (TAV). A considerable amount of research has been done in past years with vehicle concepts suitable for manned atmospheric-entry, atmospheric flight, and landing. Some of the features of these concepts that permit flight in or out of the atmosphere with maneuver capability should be useful in the mission requirements of TAV's. The concepts illustrated include some hypersonic-body shapes with and without variable geometry surfaces, and a blunt lifting-body configuration. The merits of these concepts relative to the aerodynamic behavior of a TAV are discussed.

Spearman, M. L.↗
NASA NTRS1961

Static Longitudinal and Lateral Stability Characteristics of a Right Triangular Pyramidal Lifting Reentry Configuration at Transonic Speeds

The static longitudinal and lateral stability characteristics of a right triangular pyramidal lifting reentry configuration have been investigated at Mach numbers from 0.60 to 1.19 for angles of attack up to 27.3 deg. The lower surfaces of the model had a dihedral angle of 45 deg, and the upper surface was flat. The leading-edge sweep of the model was 79.5 deg.

Olstad, Walter B.↗
NASA NTRS1961

Static Longitudinal Aerodynamic Characteristics at Transonic Speeds of a Blunted Right Triangular Pyramidal Lifting Reentry Configuration for Angles of Attack up to 110 deg

The static longitudinal aerodynamic characteristics of a blunted rig ht triangular pyramidal lifting reentry configuration have been obtai ned at Mach numbers from 0.60 t o 1.20 and angles of attack from 0 de grees to 110 degrees. The test Reynolds number, based on the mean geometric chord, varied during the tests from about 2.2 x 10 (exp 6) to 5 .7 x 10 (exp 6).

Mugler, John P., Jr.↗
NASA NTRS1958

Low-Speed Static Stability Characteristics of Two Configurations Suitable for Lifting Reentry from Satellite Orbit

An investigation of the low-speed static stability and control characteristics of 1/4-scale models of two configurations suitable for lifting reentry from satellite orbit has been made in the Langley free- flight tunnel. One of the models was a thick, all-wing configuration having a delta plan form and the other was a flat delta wing with a half-cone fuselage. The investigation showed that, in general, the all-wing configuration had better longitudinal and lateral stability characteristics than the flat delta configuration.

Paulson, John W.↗
NASA NTRS1961

Low-Subsonic-Speed Static Stability of Right-Triangular-Pyramid and Half-Cone Lifting Reentry Configurations

An investigation has been made to determine the low-subsonic-speed static stability characteristics of several right-triangular-pyramid and half-cone configurations. Also studied were the effects of various modifications, such as base extensions, nose shape, nose incidence, and ridge-line shape. The investigation showed that, in general, the models had satisfactory longitudinal and lateral stability. The basic pyramid model and the conical ridge-line model with or without a rounded nose had almost identical longitudinal and lateral stability characteristics and lift-drag ratios. The lift-drag ratios of the cylindrical ridge-line and half-cone models were considerably lower than those of the conical ridge-line model. The addition of a 20 degree boattail to the models increased the lift-drag ratios but decreased the directional stability, whereas a streamwise base extension was more effective in increasing the lift-drag ratios and increased the directional stability.

Ware, George M.↗