Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS- TAIL SURFACES, HORIZONTAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1923

Pressure Distribution over the Rudder and Fin of an Airplane in Flight

This investigation was carried out by the National Advisory Committee for Aeronautics at the Langley Memorial Aeronautical Laboratory for the purpose of determining the loads which occur on the vertical tail surfaces in flight. The method consisted in measuring the pressures simultaneously at 28 points on the rudder and fin by means of a recording multiple manometer. The results show that the maximum load encountered in stunting was 7 pounds per square foot on the rudder and fin, and it is probable that this might rise to 10 pounds per square foot in a violent barrel roll; but in steady flight the average loads do not exceed 0.6 pound per square foot. The maximum load on the rudder and fin may occur at the same instant as the maximum load on the horizontal tail surfaces and the maximum normal acceleration. The torsional moment about the axis of the fuselage due to the rudder and fin may rise as high as 250 foot-pound. The results obtained from this investigation have a direct application to the design of the rudder, fin, and fuselage.

Norton, F H↗
NASA NTRS1948

Lifting-surface-theory aspect-ratio corrections to the lift and hinge-moment parameters for full-span elevators on horizontal tail surfaces

A limited number of lifting-surface-theory solutions for wings with chordwise loadings resulting from angle of attack, parabolic-ac camber, and flap deflection are now available. These solutions were studied with the purpose of determining methods of extrapolating the results in such a way that they could be used to determine lifting-surface-theory values of the aspect-ratio corrections to the lift and hinge-moment parameters for both angle-of-attack and flap-deflection-type loading that could be used to predict the characteristics of horizontal tail surfaces from section data with sufficient accuracy for engineering purposes. Such a method was devised for horizontal tail surfaces with full-span elevators. In spite of the fact that the theory involved is rather complex, the method is simple to apply and may be applied without any knowledge of lifting-surface theory. A comparison of experimental finite-span and section value and of the estimated values of the lift and hinge-moment parameters for three horizontal tail surfaces was made to provide an experimental verification of the method suggested. (author)

Swanson, Robert S↗
NASA NTRS1954

Effect of Horizontal-Tail Span and Vertical Location on the Aerodynamic Characteristics of an Unswept Tail Assembly in Sideslip

An investigation has been conducted in the Langley stability tunnel on a vertical-tail model with a stub fuselage in combination with various horizontal tails to determine the effect of horizontal-tail span and vertical location of the horizontal tail relative to the vertical tail on the aerodynamic characteristics of an unswept tail assembly in sideslip. The results of the investigation indicated that the induced loading carried by the horizontal tail produced a rolling moment about the point of attachment to the vertical tail which was strongly influenced by horizontal-tail span and vertical locations. The greatest effect of horizontal-tail span on the rolling-moment derivative of the complete tail assembly was obtained for horizontal-tail locations near the top of the vertical tail. Span loadings which were reduced to the static-stability derivatives were calculated for each configuration tested by applying the well-known finite-step method used for wings to the intersecting surfaces of the vertical and horizontal tails. The finite-step method provides a simple and effective means of investigating the span loadings of intersecting surfaces.

Riley, Donald R↗
NASA NTRS1930

Flight Tests on U.S.S. Los Angeles. Part I : Full Scale Pressure Distribution Investigation

The primary purpose of this investigation was to obtain simultaneous data on the loads and stress experience in flight by the U. S. S. Los Angeles which could be used in rigid airship structure design. A secondary object of the investigation was to determine the turning and drag characteristics of the airship. The aerodynamic loading was obtained by measuring the pressure at 95 locations on the tail surfaces, 54 on the hull, and 5 on the passenger car. These measurements were made during a series of maneuvers consisting of turns and reversals in smooth air and during a cruise in rough air which was just short of squall proportions. The results of the pressure measurements on the hull indicate that the forces on the forebody of an airship are relatively small. The tail surface measurements show conclusively that the forces caused by gusts are much greater than those caused by horizontal maneuvers. In this investigation the tail surface loadings caused by gusts closely approached the designed loads of the tail structure. The turning and drag characteristics will be reported in separate reports.

De France, S J↗
NASA NTRS1929

The Pressure Distribution over the Horizontal and Vertical Tail Surfaces of the F6C-4 Pursuit Airplane in Violent Maneuvers

This investigation of the pressure distribution on the tail surfaces of a pursuit airplane in violent maneuvers was conducted for the purpose of determining the maximum loads likely to be encountered on these surfaces in flight. The information is a part of that needed for a revision of existing loading specifications to bring these into closer agreement with the actual flight conditions. A standard F6C-4 airplane was used and the pressure distribution over the right horizontal and complete vertical tail surfaces was recorded throughout violent maneuvers. The results show that the existing loading specifications do not conform satisfactorily to the loadings existent in critical conditions, and in some cases were exceeded by the loads obtained. An acceleration of 10.5 G. Was recorded in one maneuver in which the pilot suffered severely; it is therefore indicated that the limits of the physical resistance of the pilot to violent maneuvers are being approached. Navy specifications for the structural design of tail surfaces are included as an appendix. (author)

Rhode, R V↗
NASA NTRS1921

The Pressure Distribution over the Horizontal Tail Surfaces of an Airplane II

This investigation was undertaken to determine whether the results obtained upon model tail surfaces can be used to accurately predict loads upon the full-sized tail; and also to find the distribution of load when large elevator angles are used, as the loads from such angles can not be obtained readily in free flight. The method consisted in using a metal horizontal tail surface inside of which small air passages, connecting with a series of holes in the surface, led the pressure off from the tail in rubber tubes. In this way the pressure at each of these holes was measured by a manometer at several angles of attack and several to the loading under similar conditions in the full-sized airplane and the manner of distribution is quite similar in the two cases when there is no slip stream.

Norton, F H↗