Search NASA⌕ Search

SEARCH · Search NASA

Results for “LPG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

LPG Component Leak Frequency Estimation

Liquefied petroleum gas (LPG) is used in heating, cooking, and as a vehicle fuel (called autogas). A safety risk assessment may be needed to assess potential hazard scenarios and inform the regulations, codes, and standards that apply to LPG facilities, such as autogas refueling facilities. The frequency of unintended releases in an LPG system is an important aspect of a system quantitative risk assessment. This report documents estimation of leakage frequencies for individual components of LPG systems. These frequencies are described using uncertainty distributions obtained with Bayesian statistical methods, generic data, and LPG data which were publicly available. There was a lack of LPG data in the literature, so frequencies for most components were developed with generic data and should be used cautiously; without additional information about component leak frequencies in LPG systems, it is not known whether these generic frequencies may be conservative or non-conservative.

02 PETROLEUM↗
DOE OSTI2024

Development of advanced combustion strategies for direct injection heavy duty LPG engines to achieve near-diesel engine efficiency

The Vehicle Technologies Office funds early-stage, high-risk research to develop technology upon which industry can implement innovative transportation energy technologies that increase efficiency, decrease cost, and expand use of domestic energy sources, such as liquefied petroleum gas (LPG). To improve the viability of medium and heavy-duty vehicles the LPG engine efficiency must be closer to that of diesel. This work addresses fundamental limitations to achieve diesel-like efficiencies in heavy duty on-road LPG engines. The primary goal of this research is to achieve diesel-like efficiencies in heavy duty on-road LPG engines, focusing on the Cummins 15-liter engine platform (baseline diesel efficiency of 44% at peak torque). That goal has been achieved, though more work is needed to facilitate practical implementation of the developed technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Performance, Combustion and Emissions Evaluation of Liquid Phase Port-Injected LPG on a Single Cylinder Heavy-Duty Spark Ignited Engine

Liquefied petroleum gas (LPG), like many other alternative fuels, has witnessed increased adoption in the last decade, and its use is projected to rise as stricter emissions regulations continue to be applied. However, much of its use is limited to dual fuel applications, gaseous phase injection, light-duty passenger vehicle applications, or scenarios that require conversion from gasoline engines. Therefore, to address these limitations and discover the most efficient means of harnessing its full potential, more research is required in the development of optimized fuel injection equipment for liquid port and direct injection, along with the implementation of advanced combustion strategies that will improve its thermal efficiency to the levels of conventional fuels. This paper focuses on the development of a liquid phase port-injection system for LPG, the design of a reference piston, and the baseline evaluation of the performance, combustion, and emissions characteristics of a single cylinder research engine to establish a benchmark comparable to existing LPG engines. A sweep of start of injection (SOI) timing is performed by injecting liquid LPG at several closed and open intake valve timings, which demonstrates no significant variation in engine performance, but accounts for a 10% reduction in bsCO with the optimal SOI timing. Spark timing sweep demonstrates the 50% burn crank angle location related to maximum brake torque (MBT) point with a brake thermal efficiency (BTE) of ~34% for the tested load case. The effect of equivalence ratio is also presented with optimal SOI timing at MBT condition. The engine starts exhibiting knocking combustion at 140kPa intake manifold air pressure (IMAP) with a peak torque of 253Nm and a 5% reduction in brake specific fuel consumption compared to the naturally aspirated scenario.

Fosudo, Toluwalase↗
DOE OSTI2026

AOI 5 Improved Efficiency of Medium- and Heavy-Duty Natural Gas and Propane (LPG) Engines

Spark-ignited heavy-duty (HD) natural gas engines typically experience efficiency losses at part-load operation due to throttling requirements needed to maintain stoichiometric combustion. A substantial portion of medium- and heavy-duty engine operation occurs in this low-load region, resulting in increased brake-specific carbon dioxide emissions and reduced overall efficiency. This project designed, developed and demonstrated cylinder deactivation (CDA) technology on an HD natural gas engine to mitigate these losses. CDA enables selective deactivation of cylinders, reducing pumping losses while maintaining required torque output and meeting vehicle noise, vibration, and harshness (NVH) targets. The project objectives were successfully achieved, demonstrating up to 12% improvement in fuel consumption over the next generation HD NG engine on key low loaded HD cycles and maintained compliance with 0.02 g/hp-hr NO x emissions with comparable or better vibrations to current product. These results confirm that CDA technology can substantially improve the fuel efficiency and environmental performance of heavy-duty natural gas engines, reinforcing their potential as a low-carbon bridge solution in the transition toward zero-emission transportation technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Low-carbon fuels for spark-ignited engines: A comparative study of compressed natural gas and liquefied petroleum gas on a CFR engine with exhaust gas recirculation

Decades of work on low-carbon fuels have established their potential for substantial emissions reductions; however, their adoption is still limited by infrastructure concerns and engine efficiency deficits. As infrastructures have begun to evolve, research on strategies that maximize engine efficiency through interactions with fuel properties must also now take center place. This paper compares the performance, emissions, and combustion characteristics of two forefront low-carbon fuels: compressed natural gas (CNG) and liquefied petroleum gas (LPG) in a cooperative fuel research (CFR) engine over a range of compression ratios and engine loads. The effects of exhaust gas recirculation (EGR), end-gas auto-ignition, and a novel combustion control tool, the combustion intensity metric (CIM), were also evaluated at different stoichiometric engine operating conditions. In comparison to LPG, CNG operation demonstrated an extended knock-free regime, allowing engine operation at higher engine loads and compression ratios, but LPG operation exhibited enhanced combustion characteristics with higher peak pressures and faster apparent heat release rates (AHRR). LPG operation achieved higher brake thermal efficiencies and lower equivalent CO 2 emissions compared to CNG operation at the tested engine loads and compression ratios. LPG demonstrated significantly higher EGR tolerance limits compared to CNG, with a maximum of 28% EGR rate, compared to 23% for CNG. This improved EGR dilution tolerance was responsible for a 90% reduction in NOx emissions for LPG compared to a maximum of 70% with CNG. EGR dilution also exhibited more effective knock mitigation potential with LPG, suppressing knock intensity values by up to 98% and transitioning the engine operation towards normal combustion from heavy knocking conditions. As a result, the CIM was found to decrease burn durations and improve the quality of combustion by controlling the desired fraction of end-gas auto-ignition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Dehydration Membrane Reactor for Production of Valuable Chemicals from CO 2 and H 2

GTI Energy and partners have been developing a technology for production of liquefied petroleum gas (LPG) from carbon dioxide (CO 2 ) and hydrogen (H 2 ) using a novel catalytic membrane reactor. The reactor contains a bi-functional catalyst for methanol synthesis and LPG synthesis, resulting in LPG production in a single reactor. A transformational dehydration membrane is used to remove water in situ, shifting the thermodynamic equilibrium towards product formation. As a result, CO 2 conversion as high as 90.2% and LPG yield as high as 60.5% were obtained at 300°C and 20 bara in the membrane reactor, which significantly exceed the literature results of the traditional reactors

03 NATURAL GAS↗
DOE OSTI2022

Techno-Economic, Feasibility, and Life Cycle Analysis of Renewable Propane (Final Report)

The Propane Education and Research Council (PERC) has engaged with the National Renewable Energy Laboratory (NREL) to develop information that is critical to understanding the current and future landscape for renewable propane (RP) and the value proposition for recovery of RP from existing and planned HEFA biorefineries. In summary the following outcomes are identified from this study: 1) production of incremental RP by increasing the severity of the hydroisomerization step is insignificant to the overall propane yield from a HEFA biorefinery, however production of renewable butane (or LPG 2 ) is quite significant thus suggesting alternate strategies for valorizing these fractions; 2) the value proposition for recovering RP and renewable LPG is quite strong, with capital recovery payback periods of 14 months for a small biorefinery producing 3.5 million gallons per year RP to as short as 2 months for a large biorefinery producing 87 million gallons per year RP. Paybacks for renewable LPG are as much as 50% shorter; and 3) current and projected expansions of renewable diesel will greatly expand the potential availability of RP as a by-product. Several promising new pathways are under development but will not significantly increase production of RP for the next decade.

09 BIOMASS FUELS↗
NASA NTRS1980

Theory of bubble dynamics in condensed explosive during start-up transient

Test firings with experimental liquid propellant gun systems indicate that the main concern standing in the way of practical application of LPG's is the possibility of unexpected explosions during start up when pressure is rapidly applied to the liquid monopropellant in the chamber. The phenomenon of many collapse-rebound cycles of imploding bubbles is theorized as the probable cause of explosions in LP systems. It may be concluded that LPG safety would be enhanced by choosing an LP with low bulk modulus, as well as low decomposition reaction rate, and that a benign looking DTA trace is not a sufficient quarantee of insensitivity to a pressure induced explosion. It is also shown that pre-pressurizing an LP charge, thus pre-compressing the bubbles near-isothermally, makes the system relatively insensitive to such pressure induced explosions. The applicability of this analysis to the question of acceleration induced explosion of explosive filled warheads is indicated.

Benreuven, M.↗
NASA NTRS1982

Vehicle conversion to hybrid gasoline/alternative fuel operation

The alternative fuels considered are compressed natural gas (CNG), liquefied natural gas (LNG), liquid petroleum gas (LPG), and methanol; vehicles were required to operate in a hybrid or dual-fuel gasoline/alternative fuel mode. Economic feasibility was determined by comparing the costs of continued use of gasoline fuel with the use of alternative fuel and retrofitted equipment. Differences in the amounts of future expenditures are adjusted by means of a total life-cycle costing. All fuels studied are technically feasible to allow a retrofit conversion to hybrid gasoline/alternative fuel operation except for methanol. Conversion to LPG is not recommended for vehicles with more than 100,000 km (60,000 miles) of prior use. Methanol conversion is not recommended for vehicles with more than 50,00 km (30,000 miles).

Donakowski, T. D.↗
DOE OSTI2023

Impact of Oxygen Storage Components in Prototype Pd-Based Three-Way Catalysts under Exhaust Conditions Relevant to Propane Engines

With increasing concerns about global warming, the push for sustainable and eco-friendly fuels is accelerating. Propane, recognized as liquefied petroleum gas or LPG, has garnered research interest as an alternative fuel due to its notable advantages, including a high-octane rating, reduced greenhouse gas emissions, and potential cost-effectiveness. However, to realize its full potential as an alternative fuel it is essential to develop catalysts that efficiently handle emissions at low temperatures. In our research, we investigated three distinct palladium (Pd)-based three-way catalyst (TWC) formulations (PdRh, Pd-only, and Pd-OSC) to investigate the influence of typical TWC components rhodium (Rh) and oxygen storage components (OSC) in exhaust scenarios relevant to propane-fueled engines. Among these, the formulation containing oxygen storage components (Pd-OSC) showed the highest reactivity for both NO and C 3 H 8 while minimizing performance degradation from hydrothermal aging (HTA). Notably, the temperature of 50% conversion (T50) for propane in the Pd-OSC fresh and HTA sample was lower by 30 °C and 13 °C, respectively, compared to the Pd-only sample, highlighting the role of oxygen storage materials in enhancing catalyst performance, even without dithering. Additionally, N 2 physisorption showed that the PdOSC sample has a higher surface area and increased pore volume. This underscores the idea that OSC materials not only augment the catalyst’s porosity but also optimize reactant accessibility to active sites, thus elevating catalytic efficiency. In addition to evaluating performance, we further explored the performance and characteristics of the catalysts using catalytic probe reactions, such as water–gas shift and steam reforming reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Intensified biogas to liquid (IBGTL) Process: Experimental validation and modeling analysis

The Intensified Biogas to Liquid (IBGTL) process aims to overcome traditional economy-of-scale barriers in biogas-to-liquid fuel production by integrating bi-reforming and Fischer-Tropsch synthesis (FTS) in a single IBGTL reactor. This reactor operates at uniform pressure with different optimized temperatures across two zones for efficient conversion, utilizing multifunctional bi-reforming catalysts and high-temperature FTS catalysts. Bench scale experiments were carried out using landfill gas (LFG) in a single pass process, and the yield data from these experiments were fed into process scale-up design and techno-economic analysis (TEA) across four scenarios: (1) a single pass process, (2) a process with material recycling, (3) a process with liquefied petroleum gas (LPG) co-product recovery, and (4) a process with electricity generation from the fuel gas produced. TEA identified Scenario 2 as the most cost-effective, achieving a Minimum Fuel Selling Price (MFSP) of $\$4.59$ per gallon, competitive with the current national diesel price of $\$4.7$ per gallon. However, comparison with the conventional two-reactor system highlights the need for catalyst performance improvements. Sensitivity analysis emphasized the importance of manufacturing cost, liquid fuel yield, and biogas flow rate. Further analysis determined that the IBGTL process must achieve a diesel mass yield beyond 11.7% to surpass the economic viability of the conventional TriFTS (Tri-reforming followed by Fischer-Tropsch Synthesis) process. If the IBGTL process attains the TriFTS yield of up to 17%, the resulting MFSP could be approximately 31% lower than the current TriFTS MFSP. Furthermore, renewable energy credits and carbon credits can further enhance the economic viability of BGTL processes.

09 BIOMASS FUELS↗
DOE OSTI2025

Projected Operational Energy Life Cycle Data 2025

These excel files contain the environmental emission projections for key building energy sources: electricity, natural gas, propane (LPG), and fuel oil. The sources and methods are provided in the report "Projected Operational Energy Life Cycle Data Development: 2025 Update." The report and data are an update to the data previously posted here: https://netl.doe.gov/energy-analysis/details?id=f8890fac-be55-44ac-aaa9-e2888bfabe93

annual energy outlook↗
DOE OSTI2023

Next Generation Durable, Cost Effective, Energy Efficient Tubular SOFC (Final Scientific/Technical Report)

The overall objective of this project is to develop and optimize a YSZ electrolyte-based solid oxide fuel cell (SOFC) technology for low cost, low temperature (~ 650°C), and high energy efficiency operation. The developed technology will be implemented and demonstrated in a high efficiency 2~3kW SOFC with applicability to sub-MW systems. A summary of significant accomplishments is provided below. Key accomplishments: 1. Improved fundamental cell technology demonstrated at single tube and system scale. Improved power output by 54% while operating at the normal temperature of 750°C. And improved power output by 33% while operating at 650°C, 100°C lower than normal temperature. 2. SPS patented internal recycle arrangement was developed and extended to operate on LPG fuel directly in a compact, high-efficiency (> 40%) system. 3. System testing was conducted to prove the long-term durability of cell improvements. Demonstrated over 8000 hours of operation at 0.21 %/1000 hrs degradation. 4. A large-scale, 2.5kW net power system demonstration was completed, which demonstrated 40% net efficiency over 1000 hours. 5. System design and cost analysis of a 1MW system utilizing a 2.5kW bundle was completed. Cost optimization of the bundle showed a reduction of nearly 80% is possible from $\$$5,790/kW to $\$$1250/kW. This lower cost is considered viable for SPS commercialization.

03 NATURAL GAS↗
NASA NTRS1983

Assessment of institutional barriers to the use of natural gas fuel in automotive vehicle fleets

Institutional barriers to the use of natural gas as a fuel for motor vehicle fleets were identified. Recommendations for barrier removal were developed. Eight types of institutional barriers were assessed: (1) lack of a national standard for the safe design and certification of natural gas vehicles and refueling stations; (2) excessively conservative or misapplied state and local regulations, including bridge and tunnel restrictions, restrictions on types of vehicles that may be fueled by natural gas, zoning regulations that prohibit operation of refueling stations, parking restrictions, application of LPG standards to LNG vehicles, and unintentionally unsafe vehicle or refueling station requirements; (3) need for clarification of EPA's tampering enforcement policy; (4) the U.S. hydrocarbon standard; (5) uncertainty concerning state utility commission jurisdiction; (6) sale for resale prohibitions imposed by natural gas utility companies or state utility commissions; (7) uncertainty of the effects of conversions to natural gas on vehicle manufactures warranties; and (8) need for a natural gas to gasoline equivalent units conversion factor for use in calculation of state road use taxes.

Jablonski, J.↗
NASA NTRS1982

From Lift-Off to Light-Off

Shuttle's propellant measurement system is produced by Simmonds Precision. Company has extensive experience in fuel management systems and other equipment for military and commercial aircraft. A separate corporate entity, Industrial Controls Division was formed due to a number of non-aerospace spinoffs. One example is a "custody transfer" system for measuring and monitoring liquefied natural gas (LNG). LNG is transported aboard large tankers at minus 260 degrees Fahrenheit. Value of a single shipload may reach $15 million. Precision's LNG measurement and monitoring system aids accurate financial accounting and enhances crew safety. Custody transfer systems have been provided for 10 LNG tankers, built by Owing Shipbuilding. Simmonds also provided measurement systems for several liquefied petroleum gas (LPG) production and storage installations. Another spinoff developed by Simmonds Precision is an advanced ignition system for industrial boilers that offers savings of millions of gallons of fuel, and a computer based monitoring and control system for improving safety and reliability in electrical utility applications. Simmonds produces a line of safety systems for nuclear and non-nuclear electrical power plants.

Source record↗
NASA NTRS2005

Advanced Fiber-optic Monitoring System for Space-flight Applications

Researchers at Luna Innovations Inc. and the National Aeronautic and Space Administration s Marshall Space Flight Center (NASA MSFC) have developed an integrated fiber-optic sensor system for real-time monitoring of chemical contaminants and whole-cell bacterial pathogens in water. The system integrates interferometric and evanescent-wave optical fiber-based sensing methodologies with atomic force microscopy (AFM) and long-period grating (LPG) technology to provide versatile measurement capability for both micro- and nano-scale analytes. Sensors can be multiplexed in an array format and embedded in a totally self-contained laboratory card for use with an automated microfluidics platform.

Hull, M. S.↗