Search NASA⌕ Search

SEARCH · Search NASA

Results for “Large Helical Device”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Recent advances in plasma control and physics research in the Large Helical Device

The Large Helical Device (LHD), the largest superconducting helical system in the world, is equipped with advanced heating and diagnostic tools, facilitating plasma control and physics research. Data assimilation was employed for electron temperature control using a real-time Thomson scattering system and real time prediction code. A virtual LHD environment enabled visualization of escaping high-energy tritium ions and demonstrated that these ions impact the rear side of the divertor plate. Pioneering results crucial to plasma control have also been achieved. Real-time wall conditioning using Lithium granule dropping improved bulk ion energy and particle transport while simultaneously enhancing the heavy impurity transport. Progress has also been made in the investigation of turbulence-driven transport. At the confinement bifurcation, ion-scale turbulence decreased, while electron-scale turbulence increased. A change in the anisotropy of turbulent eddies was also observed at the confinement bifurcation. Coexistence of local and non-local turbulence was identified in electron-scale turbulence. Non-local turbulence exhibited the rapid spatial propagation of perturbations throughout the plasma, while local turbulence followed the temperature gradient. A transition between drift-wave turbulence and magnetohydrodynamics (MHD) turbulence was observed with the turbulence minimized at the transition condition. Machine learning analysis was employed to evaluate the temperate and density conditions of this turbulence transition. Then, real-time control of fueling and heating was applied to maintain the turbulence transition condition, improving the energy confinement enhancement factor by 20%. In addition, evidence was obtained for collisionless ion heating by energetic-ion-driven geodesic acoustic modes and MHD bursts. These achievements represent unique contributions to the development of fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Real-time wall conditioning and recycling modification utilizing boron and boron nitride powder injections into the Large Helical Device

Controlled particulate injections from the PPPL impurity powder dropper (IPD) into the Large Helical Device have demonstrated positive effects on the wall conditions on both an intra and inter-shot basis. Here injections over a range of densities, input powers, pulse lengths, heating schemes, injection quantities and main ion species show conclusive evidence of improvement to plasma wall conditions. Successful injections are confirmed by both spectroscopic measurements as well as real-time visible camera signals. In 7 s long plasmas the responses include a reduction in wall recycling as well as a reduction in native impurity content as observed over the course of several discharges. For plasmas longer than 40 s, improvements to the recycling rate and increased impurity control are observed in real time as a consequence of the extended particulate injections. These experiments demonstrate the extended applicability of this solid particulate conditioning technique to the control and maintenance of the plasma wall conditions. In addition they are an important initial step in the development of the real-time boronization technique as a supplement to standard conditioning scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Full-torus impurity transport simulation for optimizing plasma discharge operation using a multi-species impurity powder dropper in the large helical device

The transport of impurities supplied by a multi-species impurity powder dropper (IPD) in the large helical device (LHD) is investigated using a three-dimensional peripheral plasma fluid code (EMC3-EIRENE) coupled with a dust transport simulation code (DUSTT). The trajectories of impurity powder particles (Boron, Carbon, Iron, and Tungsten) dropped from the IPD and the impurity transport in the peripheral plasma are studied in a full-torus geometry. The simulation reveals an appropriate size of the impurity powder particles and an optimum operational range of the dust drop rates for investigating the impurity transport without inducing radiation collapse. The simulation also predicts a favourable plasma discharge condition for wall conditioning (boronization) using the IPD in order to deposit boron to high plasma flux and neutral particle density areas in the divertor region in the inboard side of the torus.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Overview of Large Helical Device experiments of basic plasma physics for solving crucial issues in reaching burning plasma conditions

Recently, experiments on basic plasma physics issues for solving future problems in fusion energy have been performed on a Large Helical Device. There are several problems to be solved in future devices for fusion energy. Emerging issues in burning plasma are: alpha-channeling (ion heating by alpha particles), turbulence and transport in electron dominant heating helium ash exhaust, reduction of the divertor heat load. To solve these problems, understanding the basic plasma physics of (1) wave–particle interaction through (inverse) Landau damping, (2) characteristics of electron-scale (high-k) turbulence, (3) ion mixing and the isotope effect, and (4) turbulence spreading and detachment, is necessary. This overview discusses the experimental studies on these issues and turbulent transport in multi-ion plasma and other issues in the appendix.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Experimental study on boron distribution and transport at plasma-facing components during impurity powder dropping in the Large Helical Device

Toward real-time wall conditioning, impurity powder dropping experiments with boron powder were performed in the 22nd experimental campaign of the Large Helical Device. To examine the deposition and desorption process of boron, we focus on boron hydride (BH) molecules which presumably populate near plasma-facing components. We performed spatially-resolved spectroscopic measurements of emission by boron ions and BH molecules. From the measurement, we found that BH and B + were concentrated on the divertor viewing chord, which suggest boron deposition in the divertor region. By comparing Hγ emissions with and without boron injection, neutral hydrogen shows uniform reduction in the SOL region, whereas less reduction of neutral hydrogen is confirmed in the divertor region. Although emissions from BH and B + increased linearly, emissions by B0 and B4 + became constant after the middle of the discharge. Continuous reduction of carbon density in the core plasma was confirmed even after B 0 and B 4 + became constant. The results may show reduction of hydrogen recycling and facilitation of impurity gettering by boron in the divertor region and thus effective real-time wall conditioning.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Simulation of the TAEs’ saturation phase in the Large Helical Device: MHD burst

Here, the aim of the present study is to analyze the saturation regime of the toroidal Alfven eigenmodes (TAE) in the Large Helical Device plasma, particularly the MHD burst. The linear and nonlinear evolution of the TAEs are simulated by the FAR3d code that uses a reduced MHD model for the thermal plasma coupled with a gyrofluid model for the energetic particle (EP) species. The linear simulations indicate the overlapping of 1/2–1/1, 2/3–2/4 and 3/5–3/6 TAEs in the inner-middle plasma region and frequency range of 45–75 kHz, triggered by EPs with an energy of T f = 45 keV and EP β = 0.022. The nonlinear simulations show that 2/3–2/4 and 3/4–3/5 TAEs are further destabilized due to the energy transfer from the 1/1–1/2 TAE, leading to broad TAE radial overlapping and triggering of the MHD burst. The energy of the 1/1–1/2 TAE is also nonlinearly transferred to the thermal plasma destabilizing the 0/0 and 0/1 modes, inducing the generation of shear flows and zonal currents, as well as large deformations in the thermal pressure and EP density radial profiles. The nonlinear simulation reproduces the same succession of instabilities and the same frequency range with respect to the experiment. The instability propagates outward during the bursting phase, showing a large decrease of the EP density profile between the middle-outer plasma, indicating the loss of part of the EP population that explains the decrease in the plasma heating efficiency observed during the MHD burst.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Self‐consistent transport simulation of boron dust particle injection in the peripheral plasma in Large Helical Device

Abstract The trajectories and the ablation positions of boron dust particles dropped from an impurity powder dropper in the peripheral plasma in the Large Helical Device (LHD) were calculated using a three‐dimensional edge plasma simulation code (EMC3‐EIRENE) and a dust transport simulation code (DUSTT). The simulation shows that the trajectory of the boron dust particles is deflected at the upper divertor leg due to the effect of the hydrogen plasma flow, and the ablation positions of the dust particles in an ergodic layer change toward the outboard side of the torus for higher plasma densities. The effect of the boron ion flow in the divertor leg on the deflection is investigated by coupling the two codes self‐consistently. The simulation predicts that the boron ions in the divertor leg, which are produced by sputtering on the divertor plates, which do not affect the change in the ablation positions. It also shows that the ablation positions move toward the inboard side and approach the Last Closed Flux Surface (LCFS) in case of increased boron dust drop rates, which is caused by the lowered plasma flow in the upper divertor leg due to the lowered electron temperature by radiation cooling by the dropped dust particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

A reduced-turbulence regime in the Large Helical Device upon injection of low-Z materials powders

Abstract Recently an improved confinement regime, characterized by reduced turbulent fluctuations has been observed in the Large Helical Device upon the injection of boron powder into the plasma (Nespoli et al 2022 Nat. Phys. 18 350–56). In this article, we report in more detail the experimental observations of increased plasma temperature and the decrease of turbulent fluctuations across the plasma cross section, on an extended database. In particular, we compare powders of different materials (B, C, BN), finding similar temperature improvement and turbulence response for the three cases. Modeling of the powder penetration into the plasma and of neoclassical electric field and fluxes support the interpretation of the experimental results. Additionally, we report evidence of the temperature improvement increasing with powder injection rates and decreasing for both increasing density and heating power. Though, plasma turbulence response varies depending on the initial conditions of the plasma, making it difficult to draw an inclusive description of the phenomenon.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Energetic particle transport and loss induced by helically-trapped energetic-ion-driven resistive interchange modes in the Large Helical Device

Here, energetic-ion confinement and loss due to energetic-ion driven magnetohydrodynamic modes are studied using comprehensive neutron diagnostics and orbit-following numerical simulations for the Large Helical Device (LHD). The neutron flux monitor is employed in order to obtain global confinement of energetic ions and two installed vertical neutron cameras (VNCs) viewing different poloidal cross-sections are utilized in order to measure the radial profile of energetic ions. A strong helically-trapped energetic-ion-driven resistive interchange mode (EIC) excited in relatively low-density plasma terminated high-temperature state in LHD. Changes in the neutron emission profile due to the EIC excitation are clearly visualized by the VNCs. The reduction in the neutron signal for the helical ripple valley increases with EIC amplitude, which reaches approximately 50%. In addition to the EIC experiment, orbit-following simulations using the DELTA5D code with EIC fluctuations were performed to assess the energetic-ion transport and loss. Two-dimensional temporal evolution results show that the neutron emissivity at the helical ripple decreases significantly due to the EIC. The rapid reduction in neutron emissivity shows that the helically-trapped beam ions immediately escape from the plasma. The reduction in the VNC signals for the helical ripple valley and the total neutron emission rate increase with increasing EIC amplitude, as observed in the experiment. Calculated line-integrated neutron emission results show that the profile measured by VNC1 has one peak, whereas the profile measured by VNC2 has two peaks, as observed in the experiment. Although the neutron emission profile for VNC2 has a relatively wide peak compared with the experimental results, the significant decrease in neutron signal corresponding to the helical ripple valley was successfully reproduced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Initial operation and data processing on a system for real-time evaluation of Thomson scattering signals on the Large Helical Device

A scalable system for real-time analysis of electron temperature and density based on signals from the Thomson scattering diagnostic, initially developed for and installed on the NSTX-U experiment, was recently adapted for the Large Helical Device and operated for the first time during plasma discharges. During its initial operation run, it routinely recorded and processed signals for four spatial points at the laser repetition rate of 30 Hz, well within the system’s rated capability for 60 Hz. We present examples of data collected from this initial run and describe subsequent adaptations to the analysis code to improve the fidelity of the temperature calculations.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Initial operation and data processing on a system for real-time evaluation of Thomson scattering signals on the Large Helical Device

A scalable system for real-time analysis of electron temperature and density based on signals from the Thomson scattering diagnostic, initially developed for and installed on the NSTX-U experiment, was recently adapted for the Large Helical Device (LHD) and operated for the first time during plasma discharges. During its initial operation run, it routinely recorded and processed signals for four spatial points at the laser repetition rate of 30 Hz, well within the system's rated capability for 60 Hz. We present examples of data collected from this initial run and describe subsequent adaptations to the analysis code to improve the fidelity of the temperature calculations.

Thomson scattering, real-time, LHD, plasma diagnos↗
DOE OSTI2025

Impurity Powder Injection Experiments in the Large Helical Device

The Impurity Powder Dropper (IPD) is a device capable of injecting controlled amounts of sub-millimetre powder into the plasma under the action of gravity. In 2019 the IPD was first installed on the Large Helical Device (LHD) in Japan, with the aim of improving the plasma performances through real time boronization and assessing the compatibility of this technique with steady state operation. Extensive series of experiments have been performed using the IPD, focused on the improvement of the plasma performance via low-Z powder injection and the understanding of the underlying physical phenomena. In this article, we review the experiments that took place in the period 2019-2024. The main results include the demonstration of the improvement of the wall conditions (reduction of intrinsic impurity content, wall recycling) both on a shot-to-shot basis and in real time. Furthermore, a reduced-turbulence improved confinement regime has been observed coincident with powder injection, resulting in an increase of the plasma temperature of the order of 25%, with enhancements that can reach up to 50% for ion temperature.

Nespoli, F. [Princeton Plasma Physics Laboratory (↗
DOE OSTI2024

Orbit-following simulations of fast-ion transport and losses due to the Alfvén eigenmode burst in the Large Helical Device

Orbit-following simulations of fast-ion transport and losses with time-dependent electromagnetic perturbations are performed to clarify the roles of Alfvén eigenmodes (AEs) and the low-frequency magnetohydrodynamic (MHD) mode observed in the kinetic-MHD hybrid simulation of AE bursts in the Large Helical Device. Fast-ion pressure profile flattening in the kinetic-MHD hybrid simulation can be reproduced by an orbit-following simulation with only the primary single AE of the time-dependent amplitude following the kinetic-MHD hybrid simulation result, while orbit-following simulations with constant AE amplitude of average level during AE burst cannot reproduce the fast-ion pressure profile flattening observed. The effects of other modes are negligible on the fast-ion pressure profile flattening. The fast-ion losses in kinetic-MHD hybrid simulation can be reproduced by an orbit-following simulation with time-dependent amplitude when the low-frequency MHD mode is considered in addition to multiple AEs. This indicates the synergetic effect of multiple AEs and the low-frequency MHD mode on fast-ion losses.

Seki, Ryohsuke↗
DOE OSTI2024

MHD-induced beta limits in the Large Helical Device

Using the extended-magnetohydrodynamics code, M3D-C1, we perform a systematic numerical study of the effect of externally applied heating on the achievable plasma beta in a ten field-period heliotron. Heat sources of varying intensity are applied to a vacuum magnetic field that is representative of the standard configuration of the Large Helical Device, with R 0 = 3.66 m, where R 0 is the radial position of the magnetic axis in vacuum. As the system is driven to a state that is unstable to low-n magnetohydrodynamic (MHD) modes, nonlinear mode interactions lead to the formation of chaotic magnetic fields. With sufficiently strong heating, a collapse of the electron temperature profile is observed. This demonstrates the necessity of simulating the self-consistent evolution of plasma profiles, without imposing assumptions on the structure of the magnetic field, to accurately determine transport properties in stellarator plasmas. It also highlights the value of these advanced simulation capabilities for accelerating the development of high-performance stellarator operating scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Full-torus impurity transport simulation in boron powder injection experiments in the Large Helical Device

The toroidal distribution of boron deposition on plasma-facing components (PFCs) in boron powder injection using an impurity power dropper (IPD) was investigated by full-torus simulation and observations in a systematic plasma density-scan experiment. The images of the ablation of dropped boron powders observed with a visible CCD camera were consistently explained by the simulations of the ablation positions of the boron powders considering the size distribution. Simulations assuming full-torus boron deposition on the PFCs did not reproduce the observed intensity profile of boron emission lines for higher plasma densities. It indicated that the density of boron deposited on PFCs installed toroidally far from the IPD was low for higher plasma densities due to the change in the ablation positions of the boron powders toward the outboard side. The experimental results verified the previous full-torus simulation of the toroidal distribution of the boron deposition in both lower and higher plasma densities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Isotope effects on transport in LHD

Abstract Isotope effects are one of the most important issues for predicting future reactor operations. Large helical device (LHD) is the presently working largest stellarator/helical device using super conducting helical coils. In LHD, deuterium experiments started in 2017. Extensive studies regarding isotope effects on transport have been carried out. In this paper, the results of isotope effect studies in LHD are reported. The systematic studies were performed adjusting operational parameters and nondimensional parameters. In L mode like normal confinement plasma, where internal and edge transport barriers are not formed, the scaling of global energy confinement time ( τ E ) with operational parameters shows positive mass dependence ( M 0.27 ; where M is effective ion mass) in electron cyclotron heating plasma and no mass dependence ( M 0.0 ) in neutral beam injection heating plasma. The non-negative ion mass dependence is anti-gyro-Bohm scaling. The role of the turbulence in isotope effects was also found by turbulence measurements and gyrokinetic simulation. Better accessibility to electron and ion internal transport barrier (ITB) plasma is found in deuterium (D) plasma than in hydrogen (H). Gyro kinetic non-linear simulation shows reduced ion heat flux due to the larger generation of zonal flow in deuterium plasma. Peaked carbon density profile plays a prominent role in reducing ion energy transport in ITB plasma. This is evident only in plasma with deuterium ions. New findings on the mixing and non-mixing states of D and H particle transports are reported. In the mixing state, ion particle diffusivities are higher than electron particle diffusivities and D and H ion density profiles are almost identical. In the non-mixing state, ion particle diffusivity is much lower than electron diffusivity. Deuterium and hydrogen ion profiles are clearly different. Different turbulence structures were found in the mixing and non-mixing states suggesting different turbulence modes play a role.

Physics↗
DOE OSTI2026

Progress in Extending the High-Temperature Plasma Regime in the LHD

In this paper, we show the expansion of the high-temperature regime and related physical phenomena in the Large Helical Device (LHD). At the LHD, we have developed a high-temperature operational regime for both ion (T i ) and electron (T e ) temperatures through understanding the physical characteristics of high-temperature plasma, the enhancement of plasma heating, and the development of technical methods such as wall recycling control and impurity control. In particular, the formation of the ion internal transport barrier (i-ITB) and electron internal transport barrier (e-ITB) in the plasma core region is the key to improving plasma performance. In addition, the deuterium experiment that began in 2017 showed that, due to the isotope effect, the thermal transport of both ions and electrons is suppressed in deuterium plasma compared to light hydrogen plasma, and that a high central temperature can be achieved efficiently. Furthermore, the combination of neutral beam injection (NBI) and electron cyclotron heating (ECH) has extended the operating conditions that simultaneously maintain high T i and T e , and comprehensive research on plasma confinement characteristics with an eye to future fusion reactor conditions has progressed.

Large Helical Device↗