Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lattice design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Beam optics ramping in underconstrained lattice design: Application to Electron-Ion Collider hadron storage ring cooling section

This paper presents the lattice design and optics ramping strategy for the cooling section of the hadron storage ring at the electron-ion collider. The main challenge is that available tuning knobs exceed beam-optics constraints. Independently optimized injection and top-energy optics often yield disconnected solutions, making interpolation impossible. To address this, we propose two new methods. The first is an intermediate-penalty scheme that ensures ramping path continuity by penalizing constraint violations at intermediate states. The second is a continuation-based approach that adapts high-energy optics to low energy, guided by an adaptive weighting scheme to balance injection and ramping constraints. The solutions meet all beam dynamics and hardware limits. The two methods offer a general strategy for ramping in systems where the solution space is under-constrained and the starting and target configurations are far apart.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Secondary Beamline Lattice Design at the MeV Test Area (MTA)

The MTA is currently configured to produce a secondary pion beam from a tungsten target, which subsequently generates muons from decay in flight. In its present lattice configuration, the currently installed air core quadrupoles are strength-limited in their ability to deliver a high muon flux to the end user. Recently, seven strong iron-core quadrupole spares from the 400-MeV Linac were acquired. Based on these quadrupoles, a new lattice has been designed that maximizes both pion transport and muon capture the line based on significantly shorter magnetic lengths, strong magnetic gradients, and consequently an enhanced angular acceptance. For this project, we demonstrated that the ratio of muons to pions increased by over an order of magnitude (approximately 75 for lattice configurations were studied), successfully capturing a phase space area as large as 13.2 [mm] x 24 [mRad] in simulation.

Winter, Wesley↗
DOE OSTI2025

Electron-Ion Collider (EIC) Hadron Storage Ring (HSR) Injection Transport Beamline (Y-Line Ext.) Lattice Design and Magnet Parameters

The preliminary design of the Electron-Ion Collider (EIC) Hadron Storage Ring (HSR) Normal Conducting Injection Beamline ( Y-Line Ext. ) lattice is discussed. The preliminary design includes the periodic cells, matching sections, state of the art Twiss parameters at the HSR injection, the magnet parameters and first order instrumentation placement. Furthermore, the beamline parameters, element coordinates, and other information are discussed. The names of the HSR Injection Beamline elements used in this technical report ( i.e. HD1, HQ1 ) are preliminary and not the official site wide names.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Accelerating the design of lattice structures using machine learning

Lattices remain an attractive class of structures due to their design versatility; however, rapidly designing lattice structures with tailored or optimal mechanical properties remains a significant challenge. With each added design variable, the design space quickly becomes intractable. To address this challenge, research efforts have sought to combine computational approaches with machine learning (ML)-based approaches to reduce the computational cost of the design process and accelerate mechanical design. While these efforts have made substantial progress, significant challenges remain in (1) building and interpreting the ML-based surrogate models and (2) iteratively and efficiently curating training datasets for optimization tasks. Here, we address the first challenge by combining ML-based surrogate modeling and Shapley additive explanation (SHAP) analysis to interpret the impact of each design variable. We find that our ML-based surrogate models achieve excellent prediction capabilities (R 2 > 0.95) and SHAP values aid in uncovering design variables influencing performance. We address the second challenge by utilizing active learning-based methods, such as Bayesian optimization, to explore the design space and report a 5 × reduction in simulations relative to grid-based search. Collectively, these results underscore the value of building intelligent design systems that leverage ML-based methods for uncovering key design variables and accelerating design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Design study of a low emittance complex bend achromat lattice

Light sources worldwide have experienced rapid growth in the last decades, pushing toward higher brightness with lower emittance to meet growing demands from the user community. The quest for higher brightness motivates the development of low-emittance ring lattices. At this point, all fourth-generation storage ring light sources employ variations of the multibend achromat (MBA) lattice. In this paper, we discuss an extension of this approach, known as complex bend achromat lattice in relation to the future NSLS-II upgrade. A detailed approach for the lattice design will be described and the developed lattice will be presented. The advantages of using our complex bend approach are evident in reaching a natural emittance as low as 23 pm at a beam energy of 3 GeV, providing a straight section of 8.4 m for long insertion devices, and acquiring a ratio of about 50% of free space with respect to the ring circumference. The design includes the use of permanent magnets largely reducing the need for power supplies. Our new approach provides an extension to the MBA concept for the next-generation light source lattice design. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
DOE OSTI2024

Topological valley Hall polariton condensation

A photonic topological insulator features robust directional propagation and immunity to defect perturbations of the edge/surface state. Exciton-polaritons, that is, the hybrid quasiparticles of excitons and photons in semiconductor microcavities, have been proposed as a tunable nonlinear platform for emulating topological phenomena. However, mainly due to excitonic material limitations, experimental observations so far have not been able to enter the nonlinear condensation regime or only show localized condensation in one dimension. Here, in this study, we show a topological propagating edge state with polariton condensation at room temperature and without any external magnetic field. We overcome material limitations by using excitonic CsPbCl 3 halide perovskites with a valley Hall lattice design. The polariton lattice features a large bandgap of 18.8 meV and exhibits strong nonlinear polariton condensation with clear long-range spatial coherence across the critical pumping density. The geometric parameters and material composition of our nonlinear many-body photonic system platform can in principle be tailored to study topological phenomena of other interquasiparticle interactions. Polariton condensation of topological propagating edge states is demonstrated with halide perovskite microcavities.

42 ENGINEERING↗
DOE OSTI2024

Hierarchical Composites Patterned via 3D Printed Cellular Fluidics

Additive manufacturing of freeform structures containing multiple materials with deterministic spatial arrangement and interactions remains a challenge for most 3D printing processes, due to complex fabrication tool requirements and limitations in printability of some material classes. Here, in this paper, a versatile method is reported to produce architected composites using the concept of cellular fluidics, in which lattices of unit cells are used as templating scaffolds to guide flowable infill materials in a programmed spatial pattern, upon which they are cured in place to produce a deterministically ordered multimaterial solid. The lattice design relies on the unit cell size, type, strut diameter, surface wetting, and distribution of cellular structures to control liquid flow and retention. Individual unit cells are tuned to achieve reliable infilling and combined into higher-order architectures to achieve multiscale composite materials with disparate mechanical properties, including those considered non-printable. Lattice design considerations for leveraging capillary phenomena and demonstrate several methods of patterning polymers in 3D-printed cellular fluidic structures are presented. The concept of tuning the compressive response of an architected composite using a flexible-elastomer as the lattice and a stiff-epoxy as the infill material is illustrated.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Initial Assessment of 3D-Printed Molybdenum Lattices as a Substrate for Liquid Metal Plasma-Facing Components

Many liquid metal plasma-facing component concepts for fusion reactors require a capillary porous material to wick the liquid metal to the surface of the component. In this work, samples of 3D-printed molybdenum lattices designed to have pore sizes ranging from 100 to 1000 µm were fabricated by two different suppliers. The dimensions of the lattice structures were characterized using an optical microscope, revealing that the lattice walls were almost systematically thicker than they were designed to be and in turn the pores are all smaller than they were designed to be. In many cases the pores were completely clogged. Several spectroscopic techniques were used to characterize the chemical composition of the materials, collectively indicating the presence of a thick layer of oxygen-rich material extending more than 1 µm below the surface. Compression testing revealed significant asymmetry in the mechanical behavior depending on which direction the force was applied relative to the print direction. Lastly, lithium wetting tests of several lattice samples were performed, and a sample with ~250-µm pores was found to soak up lithium quickly after initial wetting of the surface occurred. The implications of these results for future liquid metal plasma-facing component design are discussed.

Parsons, Matthew S. [Princeton Plasma Physics Labo↗
DOE OSTI2025

Mechanical Properties and Interfacial Bonding of Overmolded Polymer Composite Lattice Structures

This study investigates the mechanical properties and interfacial bonding of Polyamide 12 filled with Glass Fiber (PA12/GF) lattice structures overmolded with Nylon 66 (PA66) and Thermoplastic Polyurethane (TPU). The PA12/GF lattices, designed in Gyroid, Isotruss, and Octahedral geometries, were produced using the Selective Laser Sintering (SLS) technique. The thermal characteristics of both the lattice and overmolding materials were analyzed using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). The mechanical performance and interfacial bonding were evaluated through mechanical testing and microstructural analysis. The results indicate that overmolding improved flexural strength and impact resistance of the PA12/GF lattices. For instance, the plain PA12/GF Isotruss lattice exhibited a flexural strength of 15.5 MPa. By overmolding it with TPU the flexural strength increased by up to 137%, while PA66-overmolding resulted in an increase of 371%, achieving a flexural strength of 73 MPa. In terms of impact resistance, TPU-overmolding improved performance significantly, with an increase of 1800% (Gyroid) compared to the plain lattice. Microstructural analysis revealed good adhesion at the interface, especially when both the lattice and overmolding materials were thoroughly dried prior to the overmolding process to minimize interfacial porosity. This study highlights the potential of using overmolding to enhance lattice structures performance, offering lightweight and cost-efficient solutions for automotive applications.

Talabi, Isaac [ORNL] (ORCID:0000000340215594)↗
DOE OSTI2026

Spin Diagnostics Using Mott Polarimeter for the EIC Pre-Injector

Polarization measurement and front-end commissioning are critical steps in the EIC preinjector program. We designed a spin-diagnostics beamline at around 4 MeV for front-end commissioning. This paper describes a high-energy Mott polarimeter, including Mott scattering, the Sherman function, and extrapolation toward single elastic scattering in finite-thickness foils. We summarize the key equations used to calculate essential design parameters, including detection time, effective Sherman function, differential cross section, and Mott polarimeter figure of merit. We also present the diagnostics beamline lattice design and kicker design for continuous spin-polarization monitoring. These notes provide concepts, formulas, and methods for diagnostic-beamline design and commissioning measurements.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

The Sparks tracking code

This note introduces a new tracking code, Sparks, built on the foundations laid by hemod4 and designed for fast tracking of large ensembles of single particles over thousands of turns. The code is intended for the rapid evaluation of nonlinear lattice behavior through observables such as detuning, Poincaré sections, and smear, providing a computationally efficient alternative to large-scale dynamic aperture studies during lattice design and optimization.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Lattice Structured Lightweight Structural Materials

The development of lightweight structural materials is crucial for enhancing the performance and deployment feasibility of fission batteries. This study aims to produce lightweight structural materials whose strength-to-weight ratios exceed those of current widely used structural materials. To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structured models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The modeling results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison to the solid material; the increase in solid shell thickness and blend radius enhances the mechanical performance; and the effect of unit cell size on macro scale stress is minimal. Tensile testing was conducted on the solid and lattice-structured materials fabricated by laser powder bed fusion (LPBF) additive manufacturing. The experimental results agreed well with the model prediction. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for new material development.

lightweight material↗
DOE OSTI2026

Optimizing injection for the storage ring proton-EDM experiment

The proposed proton electric dipole moment (pEDM) experiment at Brookhaven National Laboratory (BNL), to be built inside the alternating gradient synchrotron (AGS) tunnel, aims to measure the proton’s electric dipole moment with a sensitivity of 10 −29 𝑒 cm. This paper presents the design of the injection line from the AGS booster to the pEDM storage ring, utilizing portions of the existing booster-to-AGS (BtA) transfer line. Building on the symmetric-hybrid lattice design [, Comprehensive symmetric-hybrid ring design for a proton-EDM experiment at below 10 −29 𝑒 cm, Phys. Rev. D 105, 032001 (2022)], our study emphasizes rigorous optics matching, detailed particle and spin tracking, and systematic error mitigation essential for achieving a target sensitivity of 10 −29 𝑒 cm. This design preserves the proton’s vertical spin orientation within ±20 mrad, a critical requirement for the pEDM measurement. Particle and spin tracking simulations using the ray-tracing code Zgoubi [F. Méot, Zgoubi users’ guide, Technical Report, Brookhaven National Laboratory (BNL), Relativistic Heavy Ion Collider (RHIC), Upton, NY, 2012] validate the design’s performance, demonstrating its feasibility for this precision experiment. The simulation results demonstrate that both clockwise (CW) and counterclockwise (CCW) injection lines meet the stringent beam envelope and polarization requirements.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Final Physics Design of Proton Improvement Plan-II at Fermilab

This paper presents the final physics design of the Proton Improvement Plan-II (PIP-II) at Fermilab, focusing on the linear accelerator (Linac) and its beam transfer line. We address the challenges in longitudinal and transverse lattice design, specifically targeting collective effects, parametric resonances, and space charge nonlinearities that impact beam stability and emittance control. The strategies implemented effectively mitigate space charge complexities, resulting in significant improvements in beam quality—evidenced by reduced emittance growth, lower beam halo, decreased loss, and better energy spread management. This comprehensive study is pivotal for the PIP-II project's success, providing valuable insights and approaches for future accelerator designs, especially in managing nonlinearities and enhancing beam dynamics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Final Physics Design of Proton Improvement Plan-II At Fermilab

This paper presents the final physics design of the Proton Improvement Plan-II (PIP-II) at Fermilab, focusing on the linear accelerator (Linac) and its beam transfer line. We address the challenges in longitudinal and transverse lattice design, specifically targeting collective effects, parametric resonances, and space charge nonlinearities that impact beam stability and emittance control. The strategies implemented effectively mitigate space charge complexities, resulting in significant improvements in beam quality -- evidenced by reduced emittance growth, lower beam halo, decreased loss, and better energy spread management. This comprehensive study is pivotal for the PIP-II project's success, providing valuable insights and approaches for future accelerator designs, especially in managing nonlinearities and enhancing beam dynamics.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Experimental measurements for extracting nonlinear invariants

Nonlinear integrable optics are a promising alternative approach to lattice design. The integrable optics test accelerator (IOTA) at Fermilab has been constructed for dedicated studies of magnetostatic elliptical elements as described by Danilov and Nagaitsev. The most compelling verification of correct implementation of the NIO lattice is direct observation of the analytically expected invariants. This report outlines the experimental and analytical methods for extracting the nonlinear invariants of motion from data gathered in the last IOTA run.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Maximizing RHIC Deliverable Luminosity with Dynamic Telescopic Beta* Squeeze

To benefit fully from the exceptional performance of the Relativistic Heavy Ions Collider (RHIC) Stochastic Cooling system during heavy ions physics store, the betatron amplitude β ∗ at a given col lision point (IP) can be squeezed from its design value by using the available space in the quadrupole triplets from smaller beam emittances. This should allow reaching new heights in deliverable lumi nosity for both STAR and PHENIX experiments. Prior to 2014, RHIC lattice designs only squeezed the interaction regions (IR’s) down to β ∗ = 0.70 m. To get past this limitation, one can use a telescopic scheme where the non-experimental insertions surrounding STAR and PHENIX are used to generate and close a β-beat wave contributing to the final squeeze in the two IP’s of interest. The following presents the various steps of the implementation in RHIC of this telescopic scheme and the corresponding changes in collision rates and specific luminosity. A full feasibility study with a review of hardware and beam dynamics limitations is also included.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Synthetic Band Structure Engineering of Graphene Using Block Copolymer-Templated Dielectric Superlattices

Engineering the electronic band structure of two-dimensional (2D) materials by imposing spatially periodic superlattice (SL) potentials opens a pathway to unconventional electronics. Nanopatterning the gate electrode or surface dielectric near 2D crystals provides a powerful strategy for realizing electrostatically tunable “remote” SLs with flexibility in lattice design. Here, we demonstrate the effectiveness of block copolymer (BCP)-templated dielectric nanopatterns for fabricating etch-free high-grade metal oxide SLs. Alumina (AlO x ) nanopatterns with hexagonal symmetry and a 38 nm SL wavelength are produced as a model material by directly converting a self-assembled BCP film via block-selective vapor phase infiltration. Despite micrometer-scale rotational disorder inherent to BCP self-assembly, electronic transport measurements of graphene reveal replica Dirac points at zero field and Hofstadter mini-gaps under finite magnetic fields. These results indicate the successful formation of remote SL potentials in graphene resulting from optimized AlO x nanopattern fabrication to achieve consistent lattice symmetry and periodicity at a macroscopic scale. The findings of this study, combined with the versatile, scalable, and cost-effective nature of BCP nanopatterning, highlight the potential of BCP-templated nanostructures for remote SL engineering in 2D crystals.

36 MATERIALS SCIENCE↗