Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lithium Metal Batteries”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Local Ultrasonic Resonance Spectroscopy of Lithium Metal Batteries for Aerospace Applications

As next-generation aircraft and vehicles continue to develop, so do their associated energy demands. Lithium metal batteries are a leading candidate to fulfill this energy requirement, but these batteries are prone to internal dendrite defects that can lead to catastrophic thermal runaway events. Current battery management systems are capable of mitigating such risks, but are unable to detect such defects until thermal runaway has already begun. Various nondestructive evaluation (NDE) techniques, particularly ultrasonic NDE, can directly monitor internal battery parameters giving them the potential to detect critical defects prior to catastrophic failure. However, most of the current battery NDE research has focused on improved battery state-of-charge (SOC) and stateof- health (SOH) monitoring with little emphasis on critical defect detection. Thus, a measurement technique sensitive to subtle battery defects is needed. In addition, the complex mechanics of ultrasound in porous, thin, multilayered batteries prompt the use of physics-based simulation to guide inspections. In this work, an ultrasonic NDE technique has been developed utilizing frequency domain analysis of local battery resonances to detect the presence of battery defects. This technique is a practical extension of local ultrasonic resonance spectroscopy (LURS) – which previously required non-contact laser ultrasonics – to measurements with piezoelectric contact and immersion scan transducers. To extend the technique to work with piezoelectric transducers, ultrasonic battery measurements were compared to a sans-battery calibration measurement. Then, a linear systems deconvolution was used to eliminate the transfer functions of extraneous factors such as the transducer and electronics, leaving only the frequency-dependent battery reflection coefficient. The LURS technique was first validated on stainless steel and aluminum plates, producing reflection coefficients in line with analytical and numerical finite element modeling (FEM) results. Functioning Li-metal pouch cells were then seeded with lithium chip defects prior to LURS measurements. The presence of these defects is shown to cause a measurable shift in the battery’s through-thickness local resonances. 2D, frequency-domain poroelastic models of ultrasonic propagation in a single-cell lithium metal pouch battery were created and corroborated these findings. Thus, this work has both extended and proven the feasibility of the LURS technique in the detection of local battery defects.

Ultrasound↗
NASA NTRS2024

Characterizing the Structure of Lithium Metal Batteries using Local Ultrasonic Resonance Spectroscopy (LURS)

Safe use of high energy density batteries is critical for electrifying aerospace and other transportation sectors. Nondestructive evaluation (NDE) techniques are being developed for characterizing battery structures throughout their lifetimes so that damage mechanisms can be better understood, and prognostic tools can be developed. In this study Local Ultrasonic Resonance Spectroscopy (LURS) is applied to lithium metal pouch cell batteries of a variety of form-factors that are brought from fabrication to end of life under different charge rates, temperatures, and loading scenarios. LURS data shows improved sensitivity to changes in structure in comparison to amplitude-based methods, allowing differences in damage development to be identified as well as giving opportunities for quality control in manufacturing.

Ultrasound↗
NASA NTRS2024

Characterizing the Structure of Lithium Metal Batteries using Local Ultrasonic Resonance Spectroscopy (LURS)

Safe use of high energy density batteries is critical for electrifying aerospace and other transportation sectors. Nondestructive evaluation (NDE) techniques are being developed for characterizing battery structures throughout their lifetimes so that damage mechanisms can be better understood, and prognostic tools can be developed. In this study Local Ultrasonic Resonance Spectroscopy (LURS) is applied to lithium metal pouch cell batteries of a variety of form-factors that are brought from fabrication to end of life under different charge rates, temperatures, and loading scenarios. LURS data shows improved sensitivity to changes in structure in comparison to amplitude-based methods, allowing differences in damage development to be identified as well as giving opportunities for quality control in manufacturing.

Matthew Webster↗
NASA NTRS2023

Evaluation of Ultrasonic Battery Inspection Techniques

Lithium metal batteries are prone to subtle defects such as internal dendrites, which can cause internal short circuits and lead to catastrophic ignition. These defects are often undetectable by battery management systems, prompting the need to advance nondestructive evaluation (NDE) techniques for battery applications. In this work, two ultrasonic approaches were compared to establish their relative merits for this application: local ultrasonic resonance spectroscopy, and guided wave ultrasound. Benchtop experiments on batteries seeded with lithium chips emulating plating were used to demonstrate the two techniques. The results show the ability to identify and map local changes in cell structure.

Ultrasound↗
NASA NTRS2023

Evaluation of Ultrasonic Battery Inspection Techniques

Lithium metal batteries are prone to subtle defects such as internal dendrites, which can cause internal short circuits and lead to catastrophic ignition. These defects are often undetectable by battery management systems, prompting the need to advance nondestructive evaluation (NDE) techniques for battery applications. In this work, two ultrasonic approaches were compared to establish their relative merits for this application: local ultrasonic resonance spectroscopy, and guided wave ultrasound. Benchtop experiments on batteries seeded with lithium chips emulating plating were used to demonstrate the two techniques. The results show the ability to identify and map local changes in cell structure.

Ultrasound↗
NASA NTRSDate not supplied

Elastic-Poroelastic Simulation of Locally Resonant Ultrasound for Aging Li-Metal Batteries

An elastic-poroelastic simulation of ultrasound inspection for lithium-metal batteries is presented and compared to empirical reflection spectra measured during battery cycling. Simulated reflection spectra were obtained using a two-dimensional (2D) plane strain model, comprised of dozens of individual microns-thick layers within a Li-metal pouch cell. The simulated reflection spectra were then compared to ultrasonic reflection spectra measurements taken intermittently during cell cycling. A sensitivity analysis and parameter calibration were performed for the pristine pouch cell simulation prior to cycling, providing a baseline to account for difficult to measure poroelastic material parameters. Then, the reduction in solid Li anode thickness and corresponding growth into a mossy lithium layer was modeled to represent aging conditions. Results from both simulations and empirical inspections show similar trends in through-thickness resonance frequencies due to cell aging.

Battery↗
NASA NTRS2019

Development of Solid State Electrolytes for Li-Metal Based High Capacity Battery

NASA future missions demand safe, high specific energy (>400 Wh/kg) batteries. Current state-of-the-art (SOA) lithium-ion batteries (LIBs) can only provide ~150-200 Wh/kg in energy capacity, which is unable to meet NASA's future energy goals, and also pose safety issues due to the use of liquid flammable electrolyte. There are intense on-going development activities to increase battery energy density. The use of Li metal as an anode material has emerged as one highly attractive option for achieving high-energy, next generation batteries. This is because Li has many advantages. It is the lightest metal, but also has the highest theoretical capacity. It also has the lowest potential, which boosts whole cell voltage, and Li metal is 100% active material and requires no binder. Thus, Li metal is an ideal anode material for high energy battery chemistries. Lithium metal based advanced battery chemistries are envisioned to be mission enhancing and, in many cases, mission enabling for future space and aeronautic applications. However, the reliable use of this exceptionally high capacity anode in a commercial rechargeable battery has not been achieved due to safety and reliability concerns resulting from thermal runaway and short-circuit issues due to dendritic growth on the Li metal anode from lithium plating during charge-discharge cycles. A solid state electrolyte, such as garnet/ceramic or solid polymer nanocomposite electrolyte, is a promising approach to make Li metal safely cycling. The solid state electrolyte is non-flammable and eliminates leakage and fire hazard by replacing the liquid flammable electrolyte. However, the low-ionic conductivity and high interfacial impedance are the key issues to be overcome. In this presentation, the research activities on solid state electrolyte development funded by the NASA Advanced Energy Storage System program and by the NASA Center Innovative Fund will be presented, and the progress and results will be also discussed.

Wu, James J.↗
NASA NTRS2002

Carbon Materials Embedded with Metal Nanoparticles as Anode in Lithium-Ion Batteries

Carbon materials containing metal nanoparticles that can form an alloy with lithium were tested for their capacity and cycle life to store and release lithium electrochemically. Metal nanoparticles may provide the additional lithium storage capacity as well as additional channels to conduct lithium in carbon. The cycle life of this carbon-metal composite can be long because the solid-electrolyte interface (SEI) on the carbon surface may protect both lithium and the metal particles in the carbon interior. In addition, the voids in the carbon interior may accommodate the nanoparticle's volume change, and such volume change may not cause much internal stress due to small sizes of the nanoparticles. This concept of improving carbon's performance to store and release lithium was demonstrated using experimental cells of C(Pd)/0.5M Lil-50/50 (vol.%) EC and DMC/Li, where C(Pd) was graphitized carbon fibers containing palladium nanoparticles, EC was ethylene carbonate, and DMC was dimethyl carbonate. However, such improvement was not observed if the Pd nanoparticles are replaced by aluminum, possibly because the aluminum nanoparticles were oxidized in air during storage, resulting in an inert oxide of aluminum. Further studies are needed to use this concept for practical applications.

Hung, Ching-cheh↗
NASA NTRS2007

Lithium Dinitramide as an Additive in Lithium Power Cells

Lithium dinitramide, LiN(NO2)2 has shown promise as an additive to nonaqueous electrolytes in rechargeable and non-rechargeable lithium-ion-based electrochemical power cells. Such non-aqueous electrolytes consist of lithium salts dissolved in mixtures of organic ethers, esters, carbonates, or acetals. The benefits of adding lithium dinitramide (which is also a lithium salt) include lower irreversible loss of capacity on the first charge/discharge cycle, higher cycle life, lower self-discharge, greater flexibility in selection of electrolyte solvents, and greater charge capacity. The need for a suitable electrolyte additive arises as follows: The metallic lithium in the anode of a lithium-ion-based power cell is so highly reactive that in addition to the desired main electrochemical reaction, it engages in side reactions that cause formation of resistive films and dendrites, which degrade performance as quantified in terms of charge capacity, cycle life, shelf life, first-cycle irreversible capacity loss, specific power, and specific energy. The incidence of side reactions can be reduced through the formation of a solid-electrolyte interface (SEI) a thin film that prevents direct contact between the lithium anode material and the electrolyte. Ideally, an SEI should chemically protect the anode and the electrolyte from each other while exhibiting high conductivity for lithium ions and little or no conductivity for electrons. A suitable additive can act as an SEI promoter. Heretofore, most SEI promotion was thought to derive from organic molecules in electrolyte solutions. In contrast, lithium dinitramide is inorganic. Dinitramide compounds are known as oxidizers in rocket-fuel chemistry and until now, were not known as SEI promoters in battery chemistry. Although the exact reason for the improvement afforded by the addition of lithium dinitramide is not clear, it has been hypothesized that lithium dinitramide competes with other electrolyte constituents to react with lithium on the surface of the anode to form a beneficial SEI. Apparently, nitrides and oxides that result from reduction of lithium dinitramide on the anode produce a thin, robust SEI different from the SEIs formed from organic SEI promoters. The SEI formed from lithium dinitramide is more electronically insulating than is the film formed in the presence of an otherwise identical electrolyte that does not include lithium dinitramide. SEI promotion with lithium dinitramide is useful in batteries with metallic lithium and lithium alloy anodes.

Gorkovenko, Alexander A.↗
NASA NTRS2015

Development of Li-Metal Battery Cell Chemistries at NASA Glenn Research Center

State-of-the-Art lithium-ion battery technology is limited by specific energy and thus not sufficiently advanced to support the energy storage necessary for aerospace needs, such as all-electric aircraft and many deep space NASA exploration missions. In response to this technological gap, our research team at NASA Glenn Research Center has been active in formulating concepts and developing testing hardware and components for Li-metal battery cell chemistries. Lithium metal anodes combined with advanced cathode materials could provide up to five times the specific energy versus state-of-the-art lithium-ion cells (1000 Whkg versus 200 Whkg). Although Lithium metal anodes offer very high theoretical capacity, they have not been shown to successfully operate reversibly.

battery↗
NASA NTRS1977

Ceramic/metal seals

Design criteria are discussed for a hermetic seal capable of withstanding the 450 C operating temperature of a lithium-metal sulfide battery system. A mechanical seal consisting of two high strength alloy metal sleeves welded or brazed to a conductor assembly and pressed onto a ceramic is described. The conductor center passes through the ceramic but is not sealed to it. The seal is effected on the outside of the taper where the tubular part is pressed down over and makes contact.

Bredbenner, A. M.↗
NASA NTRS1976

Power Sources Symposium, 27th, Atlantic City, N.J., June 21-24, 1976, Proceedings

A lithium-chlorine rechargeable battery is considered along with an FeS electrode development for a secondary Li5Si-FeS battery, the sodium-sulfur battery, nickel battery systems for electric vehicles, reactions in lithium thionyl chloride cells, progress in the development of lithium inorganic batteries, a stable electrolyte for Li/SO2 reserve cells, and rechargeable lithium transition metal sulfide batteries. Attention is also given to thermal runaway tests on nickel-cadmium aircraft batteries, the development of nickel-zinc batteries for aircraft, an evaluation of sealed lead acid batteries for aircraft applications, the charging of sealed lead-acid batteries, hydrogen recombination in sealed nickel-cadmium cells, the characteristics of nickel-hydrogen flight cells, the lithium-iodine cell, low power methanol fuel cells, and a nuclear battery hybrid configuration study.

Source record↗
NASA NTRSDate not supplied

Material Property Estimation in Thin Battery Components Using Guided Wave Measurement, Experimental Dispersion Curve Extraction and Finite Element Modeling

At NASA, we are investigating nondestructive evaluation (NDE) and structural health monitoring (SHM) techniques to detect precursors of thermal runaway failure in lithium metal based lithium ion batteries (LIB). The approach is centered on computational simulation models to guide inspection and aid in interpretation of results. Since lithium metal LIBs have combinations of solid and fluid-filled porous materials, obtaining accurate material properties is both challenging and critical for successful simulation of battery inspection. To this end, we investigated a multi-verification approach for material characterization of thin battery components. First, a laser Doppler vibrometer (LDV) was used to measure guided wave fields in thin (microns-thick) battery components subject to broadband excitation. The time-space wavefield data was converted to frequency-wave number data to extract guided wave dispersion curves. A data visualization and post processing graphics user interface (GUI) was developed at NASA to aid the data exploration and analysis. Due to the thinness of the samples, low frequency-thickness-product plate wave approximations allowed for the calculation of closed-form solutions for material elastic property estimation. These approximations were then verified by calculating the Lamb wave solutions using the previously obtained material properties. Finally, the estimated elastic material properties were implemented in a COMSOL simulation model, and dispersion curves were extracted from simulation results. The dispersion curves and derived material properties were then compared to the analysis results from the experimental data. These comparisons informed on the accuracy of the measured material properties and helped demonstrate the accuracy of the finite element analysis (FEA) computational models. This assessment will prove vital when we start simulating more complex multi-layer components and poroelastic media. This paper gives a brief background of the problem space, outlines the workflow for data analysis and verification, shows results from the workflow, and gives an overview of future plans for simulation of lithium metal LIB inspection.

Peter Juarez↗
NASA NTRS2007

Hazards, Safety and Design Considerations for Commercial Lithium-ion Cells and Batteries

This viewgraph presentation reviews the features of the Lithium-ion batteries, particularly in reference to the hazards and safety of the battery. Some of the characteristics of the Lithium-ion cell are: Highest Energy Density of Rechargeable Battery Chemistries, No metallic lithium, Leading edge technology, Contains flammable electrolyte, Charge cut-off voltage is critical (overcharge can result in fire), Open circuit voltage higher than metallic lithium anode types with similar organic electrolytes. Intercalation is a process that places small ions in crystal lattice. Small ions (such as lithium, sodium, and the other alkali metals) can fit in the interstitial spaces in a graphite lattice. These metallic ions can go farther and force the graphitic planes apart to fit two, three, or more layers of metallic ions between the carbon sheets. Other features of the battery/cell are: The graphite is conductive, Very high energy density compared to NiMH or NiCd, Corrosion of aluminum occurs very quickly in the presence of air and electrolyte due to the formation of HF from LiPF6 and HF is highly corrosive. Slides showing the Intercalation/Deintercalation and the chemical reactions are shown along with the typical charge/discharge for a cylindrical cell. There are several graphs that review the hazards of the cells.

Jeevarajan, Judith↗