Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low temperature heat release”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An Experimental and Numerical Investigation to Characterize the Low-Temperature Heat Release in Stoichiometric and Lean Combustion

This work reports on an experimental and modeling study on the low-temperature heat release (LTHR) characteristics for three RON 90 binary blends (n-heptane blended with isooctane, toluene and ethanol) in a Cooperative Fuel Research (CFR) engine at lean and stoichiometric conditions that are representative of homogeneous charge compression ignition (HCCI) and spark-ignition (SI) end-gas combustion conditions, respectively. An analysis of the end-gas temperature-pressure (T-P) trajectories was performed to identify the intake conditions leading to similar T-P trajectories between the two lambdas for each fuel blend. A heat release analysis was then conducted for the identified cases, where fuel-to-fuel differences in LTHR were identified and found to be sensitive to the operating condition. Simulations were conducted for these cases using a recently updated chemical kinetic model and a 0-D engine model, where good qualitative and reasonable quantitative agreements in LTHR were obtained. Sensitivity analysis was also performed directly on the rates of LTHR, to understand the controlling chemical reactions of LTHR, providing further insights into the fuel-to-fuel differences. The results demonstrate the significant promoting effect of n-heptane on LTHR rates, while inhibiting effects were seen for ethanol and toluene. Also highlighted was the importance of H atom abstraction reactions from the chemistry of each fuel component, which could lead to contradictory fuel behavior depending on the locations of the H site of the abstraction reaction due to the different ensuing pathways for the primary fuel radicals.

LTHR, RON 90 binary blends, sensitivity analysis↗
DOE OSTI2024

Independent Fuel Property Effects of Fuel Volatility on Low Temperature Heat Release and Fuel Autoignition (Final Report)

This Cooperative Research and Development Agreement (CRADA) project between Argonne National Laboratory (ANL), Oak Ridge National Laboratory (ORNL), and Shell Global Solutions (Shell) was initiated as part of a Directed Funding Opportunity (DFO) call for proposals from the Co-Optimization of Fuels and Engines (Co-Optima) initiative. Shell had observed that volatile fuels suppress low temperature heat release (LTHR) more than expected based on conventional gasoline autoignition metrics: research octane number (RON) and motor octane number (MON). The role of LTHR contributes to autoignition phenomena for both boosted spark ignition (BSI) and advanced compression ignition (ACI) combustion modes. ACI combustion modes are applicable to large engines in the hard-to-electrify applications such as off-road, rail, and marine. Thus, having a reliable understanding of autoignition phenomena, including being able to accurately account for the effects of fuel volatility, is particularly important as new synthetic and bio-fuel compositions are considered.This CRADA project aimed to test the hypothesis that the decreased LTHR is due to preferential evaporation of multicomponent fuels when using direct injection (DI) fueling technology, creating composition and reactivity stratification. A custom set of fuels was designed and blended to test this hypothesis by Shell, with experimental engine studies at ORNL and engine combustion modeling by ANL. However, the initial experimental findings did not show the expected effect of fuel volatility suppressing LTHR. Instead, the LTHR propensity observed was independent of the fuel volatility. Due to the unexpected experimental result, the remainder of the experimental effort was redirected to study the effect of fuel volatility on emissions under spark-ignited cold-start conditions. However, as with the LTHR experiments, the cold start effort did not show a meaningful effect of fuel volatility on cold start emissions. Meanwhile, improved engine CFD models have been developed for both LTHR and cold start operations for the Shell fuels with different volatilities. While the simulation efforts were not pursued further due to the insignificant effects of fuel volatility as shown in experiments, the models developed can be easily retooled for off-road, rail, and marine applications.

09 BIOMASS FUELS↗
DOE OSTI2025

Impact of gasoline composition on the effects of nitric oxide on autoignition and knock in a DISI engine

Modern spark-ignition engines use exhaust gas recirculation (EGR) to dilute the charge and suppress knock, enabling the use of higher compression ratios and/or more optimum combustion phasing for higher efficiency. The effectiveness of EGR is affected by the composition of the fuel and its chemical-kinetic interactions with combustion products. Among those, nitric oxide (NO) has been shown to strongly affect autoignition reactivity. However, the impact of fuel composition of the effect of NO on reactivity is not well-understood. Here, in this study, engine experiments were conducted to assess the impact of NO seeded to the intake on knock-limited operation of two gasoline fuels (high cycloalkane content, or HCA, and high olefin content, or HO). Results showed that compositionally-different fuels responded differently to NO. HCA, which was less knock-limited than HO for NO < 200 ppm, became more knock-limited for NO > 200 ppm. Moreover, it was found that differences in knock between fuels were caused by differences in autoignition chemistry and not in the sequential autoignition process of the end gas that occurs due to thermal stratification. Chemical kinetic simulations were performed to better understand the experimental results. For HCA, intermediate-temperature heat release had a greater impact on autoignition reactivity than low-temperature heat release, while the opposite was observed for HO. For both fuels, NO enhances the magnitude of low-temperature heat release via NO + HO 2 → NO 2 + OH. The effect of NO on reactivity was stronger for HCA because OH produced from NO helped to overcome the OH quenching effect of cyclopentane, a main species in HCA. In contrast, HO had relatively strong inherent low-temperature chemistry arising from iso-octane, which reduced the impact of NO on reactivity. For the range of NO mole fractions tested in this study, in-cylinder NO increased fuel’s knock propensity, especially for fuels with mild low-temperature chemistry.

Autoignition↗
DOE OSTI2021

Three-Dimensional CFD Investigation of Pre-Spark Heat Release in a Boosted SI Engine

Low-temperature heat release (LTHR) in spark-ignited internal combustion engines is a critical step toward the occurrence of auto-ignition, which can lead to an undesirable phenomenon known as engine knock. As such, correct predictions of LTHR are of utmost importance to improve the understanding of knock and enable techniques aimed at controlling it. While LTHR is typically obscured by the deflagration following the spark ignition, extremely late ignition timings can lead to LTHR occurrence prior to the spark, i.e., pre-spark heat release (PSHR). In this research, PSHR in a boosted direct-injection SI engine was numerically investigated using three-dimensional computational fluid dynamics (CFD). A hybrid approach was used, based on the G-equation model for representing the turbulent flame front and the multi-zone well-stirred reactor model for tracking the chemical reactions within the unburnt region. A recently developed best practice was also employed which keeps the well-stirred reactor model active throughout the entire simulation. This allowed for correct predictions of the previous cycle trapped residuals which have a considerable effect on the onset of LTHR. Multi-cycle simulations were conducted using Co-Optima alkylate and E30 fuels. The predicted in-cylinder pressure and heat release rate agreed well with the experimental data and served as validation for the CFD model. Following the initial validation, the dynamics of PSHR was discussed and a series of parameters of interest were assessed. First, the effect of exhaust valve temperature was investigated, qualitatively highlighting the importance of boundary conditions uncertainty. Further analyses were carried out on the effects of fuel properties, including laminar flame speed (LFS) and heat of vaporization (HOV). The results indicate that PSHR phasing is slightly advanced with lower LFS as more trapped unburnt fuel is made available for the next cycle. A similar trend was observed with lower HOV as less intense spray cooling led to higher mixture temperatures, i.e., higher mixture reactivity. Finally, a comparison of Co-Optima alkylate and E30 fuels was made using the pressure-temperature trajectory framework. It was shown that the differences between Co-Optima alkylate and E30 in PSHR tendency are correlated with both HOV and chemical effects.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

CFD modeling of pre-spark heat release in a boosted direct-injection spark-ignition engine

Accurate predictions of low-temperature heat release (LTHR) are critical for modeling auto-ignition processes in internal combustion engines. While LTHR is typically obscured by deflagration, extremely late ignition phasing can lead to LTHR prior to the spark, a behavior known as pre-spark heat release (PSHR). In this research, PSHR in a boosted direct-injection spark-ignition engine was studied using 3-D computational fluid dynamics (CFD) and detailed chemical kinetics. The turbulent combustion was modeled via a hybrid approach that incorporates the G-equation model for tracking the turbulent flame front, and the well-stirred reactor model with detailed chemistry for assessing the low-temperature reactions in unburnt gas. Simulations were conducted using Co-Optima alkylate and E30 fuels at operating conditions characterized by different PSHR intensities. The predicted in-cylinder pressure and heat release rate were found to agree well with experiments. It was found the estimate of previous-cycle trapped residuals is of utmost importance for capturing PSHR correctly. A simulation best practice was developed which keeps the detailed chemistry solver active throughout the entire simulation, allowing to track the evolution of intermediate species from one cycle to the next. Following the validation, the dynamics of PSHR were analyzed in detail employing the pressure-temperature (P-T) trajectory framework. It was shown that PSHR correlated with the first-stage ignition delay of the fuel, hence showing close relation to the in-cylinder P-T trajectory and the chemical kinetics. Besides, it was indicated that LTHR is a self-limiting process that has the effect of attenuating the thermal stratification in the combustion chamber. Furthermore, it was observed the occurrence of PSHR caused the P-T trajectory of end-gas to overlap with the negative temperature coefficient region of the fuel’s ignition-delay maps. This effect was more significant in the fuel-rich regions where engine knock tendency would be generally higher, with potential implications on knock control and mitigation.

42 ENGINEERING↗
DOE OSTI2022

Chemical kinetic interactions of NO with a multi-component gasoline surrogate: Experiments and modeling

Here this work reports an experimental and modeling study on the chemical kinetic interactions of NO with a multi-component gasoline surrogate, namely PACE-20, using a twin-piston rapid compression machine at a stochiometric fuel loading with 20% EGR (exhaust gas recirculation) by mass, pressures of 20 and 40 bar, and temperatures from 700 to 930 K. Five NO concentrations are investigated, namely 0, 20, 50, 70 and 150 ppm, where NO addition effects are characterized through changes in PACE-20 ignition reactivity and heat release characteristics. Experiments indicate that within the low-temperature regime, NO promotes low-temperature heat release rate and main ignition reactivity at low addition levels, with saturation or even inhibiting effects observed at >50 ppm NO addition, while within the NTC/intermediate-temperature regime, adding NO only promotes reactivity. A recently updated, detailed chemical kinetic model with chemistry specific to NOx/hydrocarbons interaction incorporated is used to simulate the experiments, and reasonable agreement is obtained. In-depth sensitivity and rate of production analyses are further performed. The results indicate that NO interacts with PACE-20 via two types of interaction: (a) direct interactions between NO and PACE-20 derivatives, primarily through NO+HO 2 ↔NO 2 +OH and RO 2 +NO↔RO+NO 2 , and (b) indirect interactions between PACE-20 derivatives and NO 2 produced from the direct interactions, primarily through R+NO 2 ↔RO+NO. The observed NO inhibiting effect at low temperatures and 150 ppm NO addition is attributed to the lack of HO 2 radicals to sustain NO consumption via NO+HO 2 ↔NO 2 +OH, and the take-up of inhibiting pathways via RO 2 +NO↔RO+NO 2 . The results also indicate that even with the presence of multiple fuel components, NOx/hydrocarbons interactions are highly selective, and are mainly initiated by the interactions between NO and RO 2 radicals from cyclopentane and ethanol, as well as between NO 2 and R radicals from toluene, 1,2,4-trimethylbenzene and 1-hexene. Further studies on these interactive reactions are therefore highly recommended.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Impact of low reactivity fuel type on low load combustion, emissions, and cyclic variations of diesel-ignited dual fuel combustion

In this study, cyclic variations in dual fuel combustion with diesel ignition of three different low reactivity fuels (methane, propane, and gasoline) are examined under identical operating conditions. Experiments were performed on a single cylinder research engine (SCRE) at a low load of 3.3 bar brake mean effective pressure (BMEP). The start of injection (SOI) of diesel was varied from 280 to 330 absolute crank angle degrees (CAD). Engine speed, rail pressure, and boost pressure were held constant at 1500 rpm, 500 bar, and 1.5 bar, respectively. The energy substituted by the low reactivity fuel was fixed at 80% of the total energy input. It was found that diesel-methane (DM) and diesel-propane (DP) combustion were affected by diesel mixing to a greater extent than diesel-gasoline (DG) combustion due to the higher reactivity of gasoline. The magnitude of low temperature heat release was greatest for DG combustion followed by DM and DP combustion for all SOIs. The ignition delay for DG combustion was the shortest, followed by DM and DP combustion. DM and DP combustion exhibited more cyclic variations than DG combustion. Cyclic variations decreased for DM and DP combustion when SOI was advanced; however, DG combustion cyclic variations remained essentially constant for all SOIs. Earlier SOIs (280, 290, 300, and 310 CAD) for DM and (280, 290, and 300 CAD) for DP combustion indicated some prior-cycle effects on the combustion and IMEP (i.e. some level of determinism).

Engineering↗
DOE OSTI2023

Effects of knock intensity measurement technique and fuel chemical composition on the research octane number (RON) of FACE gasolines: Part 2 – Effects of spark timing

The Research and Motor Octane Number (RON, MON) characterize a fuel’s knock resistance by rating the knock intensity of a sample fuel relative to that of Primary Reference Fuels (PRF) in a Cooperative Fuel Research (CFR) Engine. A fuel’s octane number is regulated to prevent damage from autoignition leading to knocking combustion in spark-ignition engines. The operational differences between the standard RON rating and modern engine operation are explored in a three-part publication series. The previous study focused on the effects of lambda and knock characterization. This second study primarily focuses on the effects of spark timing on RON determination. Following the findings from the first publication, the knock intensity was captured by the knockmeter and by the maximum amplitude of pressure oscillations (MAPO) at the lambda of peak knock intensity and stoichiometry. Knock-limited spark advance tests were conducted for a set of seven Fuels for Advanced Combustion Engines (FACE) from the Coordinating Research Council (CRC) with varying chemical composition, PRFs, and Toluene Standardization Fuels (TSFs). For retarded spark timings, pre-spark low-temperature heat release was found for low RON PRFs. Low RON PRFs also showed knocking characteristics before reaching the center of combustion suggesting that the use of knock-limited spark advance (KLSA) was preferred over the knock-limited combustion phasing. Primarily paraffinic fuels tended towards increased pressure oscillations while dominantly aromatic fuels experienced higher pressure rise rates. A MAPO-based KLSA correlated best to Octane Index at a negative K-factor suggesting beyond RON operation despite being at otherwise RON conditions. At stoichiometry, the MAPO-based KLSA did neither correlate to RON nor Octane Index. Finally, good agreement was found between KLSA-based effective RON from this study to the MAPO-based effective RON from the first study.

10 SYNTHETIC FUELS↗
DOE OSTI2021

Fuel Effects on Advanced Compression Ignition Load Limits

In order to increase the efficiency of light-duty gasoline engines, the Co-Optimization of Fuels and Engines (Co-Optima) initiative from the U.S. Department of Energy is investigating multi-mode combustion strategies. Multi-mode combustion can be describe as using conventional spark-ignited combustion at high loads, and at the part-load operating conditions, various advanced compression ignition (ACI) strategies are being investigated to increase efficiency. Of particular interest to the Co-Optima initiative is the extent to which optimal fuel properties and compositions can enable higher efficiency ACI combustion over larger portions of the operating map. Extending the speed-load range of these ACI modes can enable greater part-load efficiency improvements for multi-mode combustion strategies. In this manuscript, we investigate fuel effects for six different fuels, including four with a research octane number (RON) of 98 and differing fuel chemistries, iso-octane, and a market representative E10 fuel, on the load limits for two different ACI strategies: spark-assisted compression ignition (SACI) and partial fuel stratification-gasoline compression ignition (PFS-GCI) operation. Experimental results show that limits to intake boosting limit high load operation for most fuels, but high smoke emissions for high particulate matter index (PMI) fuels under SACI conditions could also be a limitation. Contrastingly, low load is limited by combustion efficiency, but these effects have more pronounced variation with fuel chemistry for PFS-GCI than with SACI. Additional, distinct effects affecting autoignition timing and peak heat release at higher speeds were identified for fuels having different low temperature heat release (LTHR) propensities for both ACI modes.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Unraveling the role of EGR olefins at advanced combustion conditions in the presence of nitric oxide: Ethylene, propene and isobutene

We report the role of EGR (exhaust gas recirculation) olefinic constituents at advanced combustion conditions in the presence of nitric oxide is unraveled in this study through experimental and modeling efforts using a twin-piston rapid compression machine operating at a stochiometric fuel loading with 20% EGR by mass, pressures of 20 and 40 bar, and temperatures from 680 to 950 K. Five different levels of olefin addition, focusing on ethylene, propene and isobutene, with a fixed amount of NO at 70 ppm are doped into test mixtures of PACE-20, a multi-component gasoline surrogate, where olefin addition effects are characterized through changes in ignition times and heat release rates. Experiments indicate that all three EGR olefins inhibit autoignition reactivity and low-temperature heat release at Tc < 850 K, with isobutene exhibiting the greatest impact, while at Tc > 850 K, low ethylene and propene additions promote reactivity. A recently updated chemical kinetic model, with detailed gasoline/NO x interacting and olefin/NO x interacting chemistry incorporated, is adopted to simulate the experiments. Simulation results are somewhat inconsistent with the experiments, where the model captures the inhibiting effects of all olefins on first-stage ignition reactivity, while consistently predicting a promoting effect on main ignition reactivity. Sensitivity and rate of production analyses reveal that adding olefins greatly alters the role of the consuming pathways for the olefins and their primary derivatives at the initial stage of the oxidation process, particularly with the presence of NO, where the olefins and their derivatives interact with both NO x species such as NO 2 and other species such as OH and HO 2 . The olefin/NO x interactions are particularly pronounced with propene and isobutene addition, where these lead to increased ignition reactivity by facilitating NO production and are mostly responsible for the disagreement between the model and experiments. Further investigations of olefin interacting chemistry, particularly those with NOx species, are needed for chemistry models to accurately predict the complicated effects of EGR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Influence of gasoline fuel formulation on lean autoignition in a mixed-mode-combustion (deflagration/autoignition) engine

We report stoichiometric spark-ignition engines suffer efficiency penalties due to throttling losses at low loads, a low specific-heat ratio of the stoichiometric working fluid, and limits on compression ratio due to end-gas autoignition leading to undesirable knocking. Mixed-Mode Combustion (MMC) mitigates these shortcomings by using a lean working fluid where a spark-initiated pilot-stabilized deflagrative flame front is followed by controlled end-gas autoignition. This MMC study investigates the effects of initial conditions (intake air temperature, intake pressure, equivalence ratio, and intake oxygen fraction) on autoignition tendency of four gasoline-range fuels with varying properties and composition. The use of fuels with varying octane sensitivity (S) allowed exploring the importance of low-temperature heat release in triggering autoignition. Fuels with high S were less reactive for conditions that promote low-temperature chemistry (operation at high intake air pressure or without N2 dilution). Conversely, an Alkylate fuel with low S showed a greater autoignition resistance at operating conditions that were unfavorable for low-temperature chemistry. Next, the effect of residual gas composition on autoignition tendency of fuels was examined with a chemical-kinetics model. Among the various molecules in the residual gas, nitric oxide (NO) enhanced the low-temperature chemistry and increased the autoignition tendency most significantly. The fuels’ autoignition response to increasing NO amount corroborates the experimental observations. Next, the sequential autoignition of the end-gas was assessed to be less impacted by thermal stratification because of lean mixtures showing relatively less low-temperature chemistry, when compared to stoichiometric mixtures. Next, the effect of changing equivalence ratio on the autoignition was found to be similar for all fuels, regardless of their S. With changing intake air temperature, the response of fuels’ autoignition tendency depended on the dilution level used. At high dilution (i.e. low intake [O2]), fuels’ reactivity increased with increasing intake air temperature. In contrast, for operation without dilution, the autoignition tendency of the low-S Alkylate fuel decreased with increasing intake air temperature, while that of high-S High Cycloalkane fuel still increased with increasing intake air temperature. In conclusion, conventional octane metrics (RON and MON) have utility in assessing the autoignition tendency under lean MMC operation. Moreover, the fuel requirements for MMC align with that of stoichiometric operation: i.e., high RON and high S fuels are desirable for stable non-knocking operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Effects of Gasoline Composition and Operating Parameters on the Response of End-Gas Autoignition to Nitric Oxide in a Lean-Burn DI-SI Engine

Lean operation of spark-ignition engines can lead to engine thermal efficiency gains and lower NOx emissions due to reduced combustion temperatures. Yet, lean operation could still face challenges in end-gas autoignition and knock generation due to higher intake pressures and trapped NO in the residual gas. Here, this study evaluates the impact of NO on end-gas autoignition for two gasoline fuels with similar octane rating but different composition: high cycloalkane fuel (HCA) and high olefin fuel (HO). Experiments were performed at stoichiometric and lean (λ = 2) conditions and at two engine speeds of 1400 rpm and 2000 rpm. Accompanying chemical kinetics simulations in CHEMKIN revealed that the mechanisms controlling the effect of NO on autoignition are similar λ = 2 and λ = 1, with NO + HO 2 = NO 2 + OH being the main pathway for enhancing reactivity by promoting low-temperature heat release (LTHR). The compositionally different fuels reacted differently to NO seeding and engine speed, and differences were augmented at λ = 2 compared to λ = 1 as the end-gas autoignition shifted to the low temperature regime. HO, which has inherent low temperature chemistry, was strongly impacted by engine speed at low NO seeding levels, with no noticeable peak of LTHR detected at 2000 rpm. On the other hand, LTHR of HCA was marginally affected by shortened residence time at higher engine speed as NO + HO 2 reaction was not greatly affected by shorter time scales, since HO 2 production was sustained even at 2000 rpm to support OH generation from NO + HO 2 . Contrary to HO, HCA exhibited greater sensitivity to NO seeding, as the increased OH production at higher NO concentrations offset the OH-quenching effect of cyclopentane, which accounts for 28.6% of HCA’s composition. Consequently, a sensitivity analysis revealed that fuels with weak inherent low-temperature chemistry, like HCA, are likely to be more sensitive to variations in NO concentration and charge temperature, whereas fuels with strong low temperature chemistry are more sensitive to variations in end-gas λ and intake pressure.

Energy↗
DOE OSTI2022

Experimental and Numerical Study on the Effect of Nitric Oxide on Autoignition and Knock in a Direct-Injection Spark-Ignition Engine

We report Nitric Oxide (NO) can significantly influence the autoignition reactivity and this can affect knock limits in conventional stoichiometric SI engines. Previous studies also revealed that the role of NO changes with fuel type. Fuels with high RON (Research Octane Number) and high Octane Sensitivity (S = RON – MON (Motor Octane Number)) exhibited monotonically retarding knocklimited combustion phasing (KL-CA50) with increasing NO. In contrast, for a high-RON, low-S fuel, the addition of NO initially resulted in a strongly retarded KL-CA50 but beyond the certain amount of NO, KL-CA50 advanced again. The current study focuses on same high-RON, low-S Alkylate fuel to better understand the mechanisms responsible for the reversal in the effect of NO on KLCA50 beyond a certain amount of NO. Experiments were conducted to measure the responses of KL-CA50 and trace-autoignition CA50, the latter being indicative of CA50 at which end-gas autoignition starts to become measurable from the apparent heat-release rate. Chemical-kinetics simulations were conducted to reveal the role of NO for end-gas autoignition, with a specific focus on sequential autoignition in a thermally stratified end-gas. The simulation results reveal that the magnitude of low-temperature heat release (LTHR) generally increases with NO. However, the relative importance of NO for enhancing LTHR diminishes when the LTHR inherent to a fuel’s chemistry is strong, such as at lower temperatures in a thermal boundary layer. This rendered more uniform LTHR within a hypothetical thermal boundary and led to a more sequential (i.e. slower) autoignition event. It was also revealed that a change in compression ratio influences the importance of intermediate-temperature heat release (ITHR) due to changes of the temperature-pressure history of the end-gas. Together with the condition where end-gas autoignition occurs more sequentially, the shorter time spent in LTHR and ITHR regime can counter the increase in autoignition reactivity at high NO levels and allow KLCA50 to advance

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Plasma thermal-chemical instability of low-temperature dimethyl ether oxidation in a nanosecond-pulsed dielectric barrier discharge

Plasma stability in reactive mixtures is critical for various applications from plasma-assisted combustion to gas conversion. To generate stable and uniform plasmas and control the transition towards filamentation, the underlying physics and chemistry need a further look. Here, this work investigates the plasma thermal-chemical instability triggered by dimethyl-ether (DME) low-temperature oxidation in a repetitive nanosecond pulsed dielectric barrier discharge. First, a plasma-combustion kinetic mechanism of DME/air is developed and validated using temperature and ignition delay time measurements in quasi-uniform plasmas. Then the multi-stage dynamics of thermal-chemical instability is experimentally explored: the DME/air discharge was initially uniform, then contracted to filaments, and finally became uniform again before ignition. By performing chemistry modeling and analyzing the local thermal balance, it is found that such nonlinear development of the thermal-chemical instability is controlled by the competition between plasma-enhanced low-temperature heat release and the increasing thermal diffusion at higher temperature. Further thermal-chemical mode analysis identifies the chemical origin of this instability as DME low-temperature chemistry. This work connects experiment measurements with theoretical analysis of plasma thermal-chemical instability and sheds light on future chemical control of the plasma uniformity.

repetitive nanosecond pulses↗
DOE OSTI2026

Effect of NO on DME-Methanol HCCI Experimental Observations

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) and successful ignition methanol at diesel–like timescales. However, if the preburn species are treated separately from the complete methanol MCCI approach the preburn heat release rate (HRR) phasing and behavior do not replicate the preburn behavior of the complete approach. Thus, the presence of the main methanol mixing controlled compression ignition (MCCI) combustion event influences the DME/methanol preburn kinetics. Specifically, it was found that trapped residual temperature alone was insufficient alone to be responsible for the observed differences, and that trace species concentrations of NO in the trapped residual gas also influenced DME/methanol kinetics increasing low temperature heat release (LTHR) magnitude and advancing high temperature heat release (HTHR) phasing. NO is not present in HCCI combustion of neat DME or DME/methanol blends nor is elevated gas temperature in the trapped residuals; both of which result in failure to accurately predict the HCCI combustion of DME/methanol blends when coupled with subsequent DI methanol MCCI. This work experimentally explores the effect of trapped residual temperature and NO on DME and DME/methanol HCCI combustion.

Jatana, Gurneesh [ORNL] (ORCID:0000000288903225)↗
DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗