Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low-Altitude”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Meteorological Analysis of Icing Conditions Encountered in Low-Altitude Stratiform Clouds

Liquid-water content, droplet size, and temperature data measured during 22 flights in predominatly stratiform clouds through the 1948-49 and the 1949-50 winters are presented. Several icing encounters were of greater severity than those previously measured over the same geographical area, but were within the limits of similar measurements obtained over different terrain within the United States. An analysis of meteorological conditions existing during the 74 flights conducted for four winters indicated an inverse relation of liquid-water concentration to maximum horizontal extent of icing clouds. Data on the vertical extent of supercooled clouds are also presented. Icing conditions were most likely to occur in the southwest and northwest quadrants of a cyclone area, and least likely to occur in the southeast and northeast quadrants where convergent air flow and lifting over the associated warm frontal surface usually cause precipitation. Additional data indicated that, icing conditions were usually encountered in nonprecipitating clouds existing at subfreezing temperatures and were unlikely over areas where most weather observing stations reported the existence of precipitation. Measurements of liquid-water content obtained during 12 flights near the time and location of radiosonde observations were compared with theoretical values. The average liquid-water content of a cloud layer, as measured by the multicylinder technique, seldom exceeded two-thirds of that which could be released by adiabatic lifting. Local areas near the cloud tops equaled or occasionally exceeded the calculated maximum quantity of liquid water.

Kline, D. B.↗
NASA NTRS1961

Preliminary Survey of Retrograde Velocities Required for Insertion Into Low-Altitude Lunar Orbits

Closed lunar orbits are envisaged in lunar mission programs. The study described herein was undertaken to obtain an appreciation of the relevant fuel consumption requirements. The retrograde impulses necessary for establishing the orbits were assumed to occur at the point of closest approach of the main earth-moon trajectory; this point, designated as the arrival position, was restricted to a lunar altitude of 5,000 nautical miles or less. The orientation of the arrival position vector relevant to any coplanar radius vector is not constrained, however, and similarly the scalar value of the arrival velocity is unrestrained. Since the arrival altitude is restricted to 5,000 nautical miles or less, the perturbing accelerations of the earth and sun are sufficiently small that the vehicle and moon essentially comprise an isolated two-body system; this is discussed in the report. Retrograde velocities are determined for any required pericynthion position. If the pericynthion orientation requirement is relaxed then a smaller retrograde velocity is in some cases possible. A comparison between minimum retrograde velocities and retrograde velocities necessary for stipulated pericynthion positions is given. Arrival velocities are correlated with feasible earth departure conditions. The equations developed for determining retrograde velocities for desired pericynthion positions are considered useful for estimating essential data for the preliminary planning of lunar missions. Some graphical representation is included herein for immediate familiarization with possible conditions.

Jenkins, Morris V.↗
NASA NTRS1962

Mission Capabilities of Ion Engines. Phase II

Payloads and mission times were calculated for space vehicles propelled by ion rockets using nuclear power supplies having specific weights from 10 t o 50 lb/kw. Included in the study were five missions: low-altitude lunar satellite, low-altitude Venus satellite, solar probe, Saturn probe, and a Jupiter satellite with a circular orbit at the altitude of Jupiter's fourth moon. The variation of payload with the ration of power supply weight to gross weight was studied and the optimum power levels thereby determined. The ion rocket payload capabilities were compared with those of high-thrust vehicles using hydrogen-oxygen rockets and tungsten-core nuclear rockets; in addition the performance of high- and low-thrust systems staged in combination has been investigated. Launch vehicles considered in this study were the Atlas-Centaur, the Saturn C-1, and the Saturn C-5.

IONIC PROPULSION↗
NASA NTRS1962

Analysis of Thermal-Protection Systems for Space-Vehicle Cryogenic-Propellant Tanks

Analytical techniques are presented that permit the calculation of heat-transfer rates with various thermal-protection systems for liquid-cryogenic-propellant tanks subjected to on-board, solar, and planetary heat fluxes. The thermal-protection systems considered include using closely spaced reflective surfaces (foils) and widely spaced reflective surfaces (shadow shields), insulation, arrangement of vehicle components, orientation with respect to radiant heating sources, and coatings for the control of solar absorptivity. The effectiveness of these thermal-protection systems in reducing propellant heating is shown both for ideal heat-transfer models and for a simplified hydrogen-oxygen terminal stage on a Mars mission. The proper orientation of a space-vehicle cryogenic tank with respect to the Sun is one of the more beneficial methods of reducing the heating effect of solar flux. Shadow shields can be extremely effective in reducing the propellant heating due to both solar and on-board fluxes. However, low-altitude planet orbits can result in high propellant heating rates due to planetary radiation reflected from the shields. For low-altitude orbits of more than a few days, foils appear to be desirable for all cryogenic-tank surfaces. Foils are also effective in reducing the on-board heating. A choice of shadow shields or foils cannot be made until a particular vehicle and a particular mission are chosen. The thermal conductivity of insulation materials would have to be lower by about two orders of magnitude with no increase in density before insulation could compete with reflective surfaces for use in long-duration thermal protection of cryogenic tanks in space. To demonstrate the application of the methods devised, thermal-protection systems are developed for a hydrogen-oxygen terminal stage for typical Mars missions.

SPACE VEHICLE↗
NASA NTRS1961

Performance Charts for Multistage Rocket Boosters

Charts relating the stage propellant fractions are given for two-and three-stage rockets launching payloads into nominal low-altitude circular orbits about the earth. A simple method is described for extending these data to higher orbit or escape missions. Various combinations of stages using RP - liquid-oxygen and hydrogen - liquid-oxygen propellants are considered. However, the results can be generalized with little error to any other propellant combination.Charts relating the stage propellant fractions are given for two-and three-stage rockets launching payloads into nominal low-altitude circular orbits about the earth. A simple method is described for extending these data to higher orbit or escape missions. Various combinations of stages using RP - liquid-oxygen and hydrogen - liquid-oxygen propellants are considered. However, the results can be generalized with little error to any other propellant combination.

MacKay, John S.↗
NASA NTRS1962

NASA TO LAUNCH RELAY EXPERIMENTAL SATELLITE

Objectives of Project Relay are to test intercontinental microwave communications by low-altitude active repeater satellites, measure energy levels of space radiation in the orbital path and determine the extent of radiation damage to solar cells and electronic components. A second Relay satellite will be launched next year. Information obtained from the Relay experiments will contribute, ultimately, to development of a future operational satellite system for world- wide communication.

COMMUNICATIONS SATELLITE↗
NASA NTRS1959

Lift and Drag of a Swept-Wing Fighter Airplane at Transonic and Supersonic Speeds

A flight investigation was made of the lift and drag of a sweptwing fighter airplane in the basic configuration and in a slats-locked-closed configuration over a Mach number range from about 0.63 to about 1.44. At a nominal lift coefficient of 0.1 negligible drag-coefficient difference existed between the two configurations over a comparable Mach number and altitude range. For the basic configuration at zero lift the supersonic drag level was about three times as great as the subsonic drag level, which was about 0.01, whereas the drag-due-to-lift factor increased about 137 percent over the test Mach number range. At comparable Mach numbers the high-altitude data produced a larger lift-curve slope and showed a more pronounced variation of lift-curve slope in the transonic region than did the low-altitude data. For the high-altitude data the lift-curve slope at a Mach number of 1.44 was approximately 62 percent of the value at a Mach number of 0.9.

SWEPT WING↗
NASA NTRS1960

II. Aerodynamic research relative to variable-sweep multimission aircraft

The development of a multimission military aircraft would be highly desirable both from the standpoint of easing the strain on the national budget by reducing the number of aircraft types and of providing versatility which would increase the effectiveness of the aircraft in the performance of a given mission. Some of the capabilities which might be required of such an aircraft are shown in figure 1 along with their respective aerodynamic and configuration requirements. The first three capabilities are grouped together since they all require good subsonic characteristics. The first, a long loiter capability for combat air patrol and the second, a long ferry range for efficient aircraft deployment both require a high subsonic lift-drag ratio. The third capability, STOL, is desirable for carrier and short-field operation and requires the development of high lift. All three of these capabilities can best be obtained with a high-aspect-ratio wing having a large span and a low-sweep angle. The fourth capability is that of a high-altitude supersonic attack or intercept and requires a high lift-drag ratio at supersonic speeds which dictates a rather slender configuration with a moderate-span wing which is either very thin or highly swept. The fifth capability listed in figure 1 is that of a low-altitude high-speed attack that would increase the probability of long-range penetration of antiaircraft defenses. The high dynamic pressures encountered on the deck at high speeds require a low-lift-curve slope to reduce the gust-induced normal accelerations, and low friction and wave drag (drag due to lift is insignificant at high dynamic pressures) to assure sufficient speed and range. In order to best satisfy these requirements, a slender aircraft having little or no wing is required. It is apparent from figure 1 that these five capabilities are highly incompatible and that an efficient multimission aircraft will require a means of varying its aerodynamic characteristics. This can be best accomplished with some type of variable-wing geometry. There are, of course, several types of variable wing geometry. However, in view of the extremely large variations in wing span desired, variable wing sweep, as indicated In the lower right sketch of figure 1, appears to provide the best method. The Langley Research Center of the National Aeronautics and Space Administration has therefore initiated a research program to provide the aerodynamic information needed for the development of a variable-sweep multimission military aircraft, and it is the purpose of this paper to briefly describe some of the results of this program.

Military aircraft↗
NASA NTRS1960

IX. Simulation requirements for the development of advanced manned military aircraft

The purpose of this paper is to review some of the more recent simulator results with emphasis on the airplane-design problem areas. Some of the simulator requirements for V/STOL and a low-altitude attack airplane will also be presented. Areas requiring additional effort are discussed briefly. Simulators for crew training however, are not considered in this paper.

Manned aircraft↗
NASA NTRS1955

Performance of Four Experimental High-btu-per-gallon Fuels in a Single Turbojet Combustor

Performance characteristics of four hydrocarbon fuels having high Btu per gallon were determined in a single turbojet combustor. At simulated low-altitude operating conditions, the fuels with high Btu per gallon generally produced more carbon than did JP-4 and JP-5 fuels. The deposits were reduced appreciably with a fuel-oil additive. At high-altitude conditions, the high Btu-per-gallon fuels gave lower efficiencies than did JP-4 or JP-5 fuels. No attempts were made to improve performance by combustor design modification.

Jonash, Edmund R↗
NASA NTRS1928

Preliminary Flight Tests of the N.A.C.A. Roots Type Aircraft Engine Supercharger

An investigation of the suitability of the N.A.C.A. Roots type aircraft engine supercharger to flight-operating conditions, as determined the effects of the use of the supercharger upon engine operation and airplane performance, is described in this report. Attention was concentrated on the operation of the engine-supercharger unit and on the improvement of climbing ability; some information concerning high speeds at altitude was obtained. The supercharger was found to be satisfactory under flight-operating conditions. Although two failures occurred during the tests, the causes of both were minor and have been eliminated. Careful examination of the engines revealed no detrimental effects which could be attributed to supercharging. Marked improvements in climbing ability and high speeds at altitude were effected. It was also found that the load which could be carried to a given moderate or high altitude in a fixed time was considerably augmented. A slight sacrifice of low-altitude performance was necessitated, however, by the use of a fixed-pitch propeller. From a consideration of the very satisfactory flight performance of the Roots supercharger and of its inherent advantages, it is concluded that this type is particularly attractive for use in certain classes of commercial airplanes and in a number of military types.

Gardiner, Arthur W↗
NASA NTRS1957

Satellite and space propulsion system

Previous papers of this conference have described rocket systems capable of launching sizable payloads into satellite orbits. Propulsion systems that might be suitable for the next steps are discussed in this paper. Some of the uses for propulsion systems once satellites have been established are as follows: (1) increasing lifetime of low-altitude satellite, (2) controlling and altering satellite orbits, (3) lunar and interplanetary exploration and (4) auxiliary electric power. (author)

Moeckel, W E↗
NASA NTRS1955

Investigation in the Langley Free-Flight Tunnel of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model Simulating the Convair F-102A Airplane

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model simulating the Convair F-102A airplane has been made in the Langley free-flight tunnel. The model in its basic configuration and with two modifications involving leading- edge slats and an increase in vertical-tail size was flown through a lift-coefficient range from 0.7 to the stall. Only relatively low-altitude conditions were simulated. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the lift-coefficient range investigated, except near the stall, where large values of static directional instability caused the model to be directionally divergent. An 80-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered acceptable over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Boisseau, Peter C.↗
NASA NTRS1953

Investigation of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model of the Convair YF-102 Airplane in the Langley Free-Flight Tunnel

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Convair YF-102 airplane has been made in the Langley free-flight tunnel. The model was flown over a lift-coefficient range from 0.5 to the stall in its basic configuration and with several modifications involving leading-edge slats and increases in vertical-tail size. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect of freeing the controls. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the speed range investigated except near the stall, where large values of static directional instability caused the model to be directionally divergent. The addition of leading-edge slats or an 8-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The use of leading-edge slats in combination with a 40-percent increase in vertical-tail size eliminated the directional divergence and produced satisfactory stability characteristics through the stall. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered satisfactory over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Johnson, Joseph L., Jr.↗
NASA NTRS1951

Investigation of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model of the Douglas XF4D-1 Airplane in the Langley Free-Flight Tunnel TED No. NACA DE 349

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Douglas XF4D-1 airplane has been made in the Langley free-flight tunnel. The model was flown with leading-edge slats retracted and extended over a lift-coefficient range from 0.5 to the stall. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect on the stability characteristics of freeing the controls. The longitudinal stability and control characteristics of the model were satisfactory for all conditions investigated except near the stall with slats extended, where the model had a slight nosing-up tendency. The lateral stability and control characteristics of the model were considered satisfactory for all conditions investigated except near the stall with slats retracted, where a change in sign of the static- directional-stability parameter Cn(sub beta) caused the model to be directionally divergent. The addition of an extension to the top of the vertical tail did not increase Cn(sub beta) enough to eliminate the directional divergence of the model, but a large increase in Cn(sub beta) that was obtainable by artificial means appeared to eliminate the divergence and flights near the stall could be made. Artificially increasing the stability derivative-Cn(sub r) (yawing moment due to yawing) and Cn(sub p) (yawing moment due to rolling) had little effect on the divergence for the range of these parameters investigated. Calculations indicate that the damping of the lateral oscillation of the airplane with slats retracted or extended will be satisfactory at sea level but will be only marginally satisfactory at 40,000 feet.

Johnson, Joseph L.↗
NASA NTRS1951

Strain-Gage Measurements of Buffeting Loads on a Jet-Powered Bomber Airplane

Buffet boundaries, buffeting-load increments for the stabilizers and elevators, and buffeting bending-moment increments for the stabilizers and wings as measured in gradual maneuvers for a jet-powered bomber airplane are presented. The buffeting-load increments were determined from strain-gage measurements at the roots or hinge supports of the various surfaces considered. The Mach numbers of the tests ranged from 0.19 to 0.78 at altitudes close to 30,000 feet. The predominant buffet frequencies were close to the natural frequencies of the structural components. The buffeting-load data, when extrapolated to low-altitude conditions, indicated loads on the elevators and stabilizers near the design limit loads. When the airplane was held in buffeting, the load increments were larger than when recovery was made immediately.

Aiken, William S., Jr.↗