SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In order to eliminate the hazard caused by residual air trapped between the concentric shells of a cryostat, these annular spaces are pressurized with helium gas. This system is more economical than the use of powdered insulation maintained at low vacuums.
By affixing perforated magnetic recording tape to the falling end of a body, acceleration and velocity were measured. The measurement was made by allowing the tape to pass between a light source and a photoelectric sensor. Data was obtained from a readout device.
Low cost TV ground receiving systems for signals transmitted from synchronous satellites, describing reception techniques, manufacturing and performance characteristics
Technology requirements for the expendable second stage of the space shuttle booster system are discussed. The primary objective of the expendable second stage (ESS) program is to define a low-cost system for placing large payloads, such as the space station or reusable nuclear shuttle, into low earth orbit. The proposed concept is to utilize a modified Saturn 5 second stage (S-2) in conjunction with the space shuttle reusable booster. The ESS retains the major S-2 structure, modified for attachment to the space shuttle booster, and incorporates both Saturn and shuttle developed propulsion and avionics hardware. No major technology breakthroughs are required to develop this ESS system. Technology application and implementation efforts in selected areas, however, should be conducted in support of the ESS detail design and development phase. The selected ESS system incorporates recovery of propulsion and avionics hardware by the shuttle orbiter for ESS reuse to minimize cost.
Refined computerized plotting system produces low-cost graphic-numeric charts that illustrate fiscal data on monthly incremental or cumulative basis, or both. Output is in the form of hard copy or microfilm, or visual-aid transparencies prepared from hard copy for rapid management status presentations.
The mARC II is a 30 kW arc-jet facility at NASA Ames Research Center used to generate high-enthalpy flows for low-cost thermal protection system (TPS) technology development. Sustained operation of downstream instrumentation and material samples is constrained by thermal loading transmitted through the arc-jet test environment, limiting achievable run times and experimental throughput. This work presents the design, integration, and validation of a cooling sleeve implemented on the sweep arm drive motor feedthrough to mitigate thermal accumulation during testing. The addition of the cooling sleeve is a simple, robust upgrade that translates directly into enhanced facility capability by supporting longer run durations, reduced turnaround time, and higher throughput.
The mARC II is a 30 kW arc-jet facility at NASA Ames Research Center used to generate high-enthalpy flows for low-cost thermal protection system (TPS) technology development. Sustained operation of downstream instrumentation and material samples is constrained by thermal loading transmitted through the arc-jet test environment, limiting achievable run times and experimental throughput. This work presents the design, integration, and validation of a cooling sleeve implemented on the sweep arm drive motor feedthrough to mitigate thermal accumulation during testing. The addition of the cooling sleeve is a simple, robust upgrade that translates directly into enhanced facility capability by supporting longer run durations, reduced turnaround time, and higher throughput.
A winding process utilizing a low-cost E-glass fabric called transverse-filament tape for low-cost production of wind turbine generators (WTG) is described. The process can be carried out continuously at high speed to produce large one-piece parts with tapered wall thicknesses on a tapered mandrel. It is being used to manufacture blades for the NASA/DOE 200-ft-diameter MOD-1 WTG and Rockwell/DOE 40-kW small wind energy conversion system (SWECS).
Circuit, suitable for operation at high signal-to-noise ratio environments, recovers pulse-code modulated data from digital telemetry systems which use phase-shift keyed subcarrier techniques. This demodulator is easily constructed from microcircuit elements and may be applied where low-cost, relatively high-level signal systems are used.
The development of an expendable second stage for use with a reusable space shuttle booster is discussed. The configuration of a low-cost, reusable multipurpose space transportation system for the 1980 time period is presented. A system capable of economically placing payloads in earth orbit which are larger and heavier than can be carried in the shuttle orbiter cargo bay is defined. The ESS/reusable shuttle system is complementary to the space shuttle system and provides mission flexibility to permit economical expansion of the overall space program.
Low-cost pilot indicator for midair collision avoidance
A low-cost fitting, fabricated from standard connectors, is used for disconnecting flow lines in cryogenic systems. Utilizing vacuum-jacketed lines made from two sizes of tubing welded at the ends, the connectors are stronger and setup time is reduced.
Satellite microwave receiver systems which convert carrier frequencies and modulation formats to produce signals compatible with VHF-UHF television receivers for low-cost service
NASA’s Goddard Space Flight Center is investigating the use of small, commercial off the shelf (COTS) spacecraft to enable breakthrough astrophysics research at radically reduced cost over previous generations of missions. This paper will focus on the Mission Systems perspective of this investigation. It will cover the spacecraft to instrument interface, and lessons learned in early concept payload development. Low-cost COTS spacecraft have proliferated in the last ~5 years. They represent an order of magnitude reduction in the cost of spacecraft bus development and acquisition. They are enabled by the advent of low-cost smallsat launch options in the immediately preceding years, and are seeded by recent distributed and disaggregated missions in other sectors such as telecommunications megaconstellations (e.g. Starlink, OneWeb, Project Kuiper) and ongoing Space Development Agency (SDA) developments. Our study was tasked with developing a standardized, mass-produceable, astrophysics payload which is reconfigurable to different wavelength bands while maintaining a single optics bench design, and a standardized mechanical, electrical, data, and thermal interface to the spacecraft bus, and which may be reconfigured to multiple COTS spacecraft offerings. In this paper we will discuss lessons learned from our case study. We will also present identified keys to mission success for performing cutting edge astrophysics observations while taking advantage of economies of scale with a disaggregated, standardized architecture.
Low-cost fabricating technique produces minute, complex air passages in fluidic devices. Air jet interactions in these function as electronic and electromechanical control systems. Wax cores are fabricated without distortion by two-wax process using nonsoluble pattern-wax and water-soluble wax. Significant steps in fabrication process are discussed.
Additive manufacturing (AM) enables low-cost, lightweight, and geometrically flexible antennas for rapid deployment missions. This work reports a left-hand circularly polarized magneto-electric dipole printed on a Radix dielectric with inkjet silver metallization and demonstrated as a process replacement for NASA weather-balloon RF hardware. By combining substrate fabrication and metallization, AM provides value for unrecoverable or field-replaceable systems. A physics based verification workflow links AM-specific material behavior to electromagnetic performance and yields bounded total, radiation, and mismatch efficiencies. Standard surface-impedance and roughness models failed to reproduce the frequency-dependent radiation loss observed in printed inks, underscoring the need for AM-specific conductor parameterization. Mission testing confirmed TDRSS link closure from NASA’s Columbia Scientific Balloon Facility and validated a repeatable print–measure–fly workflow for bounding RF performance and qualifying AM antennas for field use.
Additive manufacturing (AM) enables low-cost, lightweight, and geometrically flexible antennas for rapid deployment missions. This work reports a left-hand circularly polarized magneto-electric dipole printed on a Radix dielectric with inkjet silver metallization and demonstrated as a process replacement for NASA weather-balloon RF hardware. By combining substrate fabrication and metallization, AM provides value for unrecoverable or field-replaceable systems. A physics based verification workflow links AM-specific material behavior to electromagnetic performance and yields bounded total, radiation, and mismatch efficiencies. Standard surface-impedance and roughness models failed to reproduce the frequency-dependent radiation loss observed in printed inks, underscoring the need for AM-specific conductor parameterization. Mission testing confirmed TDRSS link closure from NASA’s Columbia Scientific Balloon Facility and validated a repeatable print–measure–fly workflow for bounding RF performance and qualifying AM antennas for field use.
Low cost rate transportation as mandatory goal for future space program, discussing recovery and reuse, launch system costs, hardware development, etc