SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This thesis presents a study of the bending stress in smooth skin, aluminum alloy, true monocoque fuselage sections of varying ratio of diameters to thickness. The test specimens - circular, thin-walled cylinder were loaded to give a large bending stress in proportion to the shearing stress, in order to represent the critical section of a fuselage.
Aircraft dynamic analyses are demanding of computer simulation capabilities. The modeling complexities of semi-monocoque construction, irregular geometry, high-performance materials, and high-accuracy analysis are present. At issue are the safety of the passengers and the integrity of the structure for a wide variety of flight-operating and emergency conditions. The technology which supports engineering of aircraft structures using computer simulation is examined. Available computer support is briefly described and improvement of accuracy and efficiency are recommended. Improved accuracy of simulation will lead to a more economical structure. Improved efficiency will result in lowering development time and expense.
Explore the source record for details and available documents.
This report deals with the calculation of the bending moments in and the distortions of fuselage rings upon which known concentrated and distributed loads are acting. In the procedure suggested, the ring is divided into a number of beams each having a constant radius of curvature. The forces and moments caused in the end sections of the beams by individual unit displacements of the end sections are listed in a table designated as the operations table in conformity with Southwell's nomenclature. The operations table and the external loads are equivalent to a set of linear equations. For their solution the following three procedures are presented: 1) Southwell's method of systematic relaxations. This is a step-by-step approximation procedure guided by the physical interpretation of the changes in the values of the unknown. 2) The growing unit procedure in which the individual beams are combined successively into beams of increasing length until finally the entire ring becomes a single beam. In each step of the procedure a set of not more than three simultaneous linear equations is solved. 3) Solution of the entire set of simultaneous equations by the methods of the matrix calculus. In order to demonstrate the manner in which the calculations may be carried out, the following numerical examples are worked out: 1) Curved beam with both its end sections rigidly fixed. The load is a concentrated force. 2) Egg-shape ring with symmetric concentrated loads. 3) Circular ring with antisymmetric concentrated loads and shear flow (torsion of the fuselage). 4) Same with V-braces incorporated in the ring. 5) Egg-shape ring with antisymmetric concentrated loads and shear flow (torsion of the fuselage). 6) Same with V-braces incorporated in the ring. The results of these calculations are checked, whenever possible, by calculations carried out according to known methods of analysis. The agreement is found to be good. The amount of work necessary for the solution of ring problems by the methods described in the present report is practically independent of the degree of redundancy of the structure. For this reason the methods are recommended for use particularly in problems of rings having one or more internal bracing elements.
Design vessel with very low thickness-to-radius ratio to obtain low weight, and fabricate it with aid of precision tracer-lathe to limit and control imperfections in spherical shape. Vessel is thin-walled, spherical, monocoque shell constructed from hemispheres joined with sealed and bolted meridional flange.
The preliminary design of an across-the-bay Flight Support Structure optimized to the specific requirements of the Spartan program has been completed. Although approximately 15 percent heavier than the initial goal, preliminary analysis indicate very low stress levels and significant reduction in weight should be possible in the final design. This structure is capable of supporting two Spartan 200-class spacecraft or attached payloads of equivalent total weight. The inherent structural efficiency of monocoque type construction is utilized. The minimization of fabrication and assembly costs and provision for simple and versatile payload interfacing where given significant considerations. Modularity of this structure allows it to be readily adapted for use as the primary structure of an Aries-class Spartan free-flyer utilizing the Orbit trunning latch mechanisms, thus eliminating the need for a flight support structure.
Explore the source record for details and available documents.
The interrelationships between moisture and wood, conditions for dry rot spore activity, the protection of wood fibers from moisture, wood resin composites, wood laminating, quality control, and the mechanical properties of wood are discussed. The laminated veneer and the bonded sawn stock fabrication techniques, used in the construction of a turbine blade with a monocoque 'D' section forming the leading edge and a built up trailing edge section, are described. A 20 foot root end sample complete with 24 bonded-in studs was successfully subjected to large onetime loads in both the flatwise and edgewise directions, and to fatigue tests. Results indicate that wood is both a viable and advantageous material for use in wind turbine blades. The basic material is reasonably priced, domestically available, ecologically sound, and easily fabricated with low energy consumption.
An extension to existing design tools that utilize tow-steering is presented which is used to investigate the use of elastic tailoring for a flat panel with a central hole under combined loads of compression and shear. The elastic tailoring is characterized by tow-steering within individual lamina as well as a novel approach based on selective reinforcement, which attempts to minimize compliance through the use of Cellular Automata design concepts. The selective reinforcement designs lack any consideration of manufacturing constraints, so a new tow-steered path definition was developed to translate the prototype selective reinforcement designs into manufacturable plies. The minimum weight design of a flat panel under combined loading was based on a model provided by NASA-Langley personnel and analyzed by STAGS within the OLGA design environment. Baseline designs using traditional straight fiber plies were generated, as well as tow-steered designs which incorporated parallel, tow-drop, and overlap plies within the laminate. These results indicated that the overlap method provided the best improvement with regards to weight and performance as compared to traditional constant stiffness monocoque panels, though the laminates did not measure up to similar designs from the literature using sandwich and isogrid constructions. Further design studies were conducted using various numbers of the selective reinforcement plies at the core and outer surface of the laminate. None of these configurations exhibited notable advantages with regard to weight or buckling performance. This was due to the fact that the minimization of the compliance tended to direct the major stresses toward the center of the panel, which decreased the ability of the structure to withstand loads leading to instability.
At the ends of a monocoque fuselage concentrated axial forces in the skin must generally be taken up. Such axial forces must also be taken up in the case of other members where axial forces from the neighboring stressed skin construction must be considered. In order to take up these axial forces two bulkheads or reinforcing frames may be arranged at the positions where the forces are applied. If these bulkheads are in the form of rings, bending moments are set up in them. In the present paper computations are performed for obtaining the value of these bending moments.
Boeing Information, Space, and Defense Systems executed a Low Cost Large Core Vehicle Structures Assessment (LCLCVSA) under contract to NASA Marshall Space Flight Center (MSFC) between November 1997 and March 1998. NASA is interested in a low-cost launch vehicle, code named Magnum, to place heavy payloads into low earth orbit for missions such as a manned mission to Mars, a Next Generation Space Telescope, a lunar-based telescope, the Air Force's proposed space based laser, and large commercial satellites. In this study, structural concepts with the potential to reduce fabrication costs were evaluated in application to the Magnum Launch Vehicle (MLV) and the Liquid Fly Back Booster (LFBB) shuttle upgrade program. Seventeen concepts were qualitatively evaluated to select four concepts for more in-depth study. The four structural concepts selected were: an aluminum-lithium monocoque structure, an aluminum-lithium machined isogrid structure, a unitized composite sandwich structure, and a unitized composite grid structure. These were compared against a baseline concept based on the Space Shuttle External Tank (ET) construction. It was found that unitized composite structures offer significant cost and weight benefits to MLV structures. The limited study of application to LFBB structures indicated lower, but still significant benefits. Technology and facilities development roadmaps to prepare the approaches studied for application to MLV and LFBB were constructed. It was found that the cost and schedule to develop these approaches were in line with both MLV and LFBB development schedules. Current Government and Boeing programs which address elements of the development of the technologies identified are underway. It is recommended that NASA devote resources in a timely fashion to address the specific elements related to MLV and LFBB structures.
Small pyrex glass spheres, representative of stoney meteoroids, were fired into 2024-T3 aluminum alclad multiple-sheet structures at velocities to 11,000 feet per second to evaluate the effectiveness of multisheet hull construction as a means of increasing the resistance of a spacecraft to meteoroid penetrations. The results of these tests indicate that increasing the number of sheets in a structure while keeping the total sheet thickness constant and increasing the spacing between sheets both tend to increase the penetration resistance of a structure of constant weight per unit area. In addition, filling the space between the sheets with a light filler material was found to substantially increase structure penetration resistance with a small increase in weight. An evaluation of the meteoroid hazard to space vehicles is presented in the form of an illustrative-example for two specific lunar mission vehicles, a single-sheet, monocoque hull vehicle and a glass-wool filled, double-sheet hull vehicle. The evaluation is presented in terms of the "best" and the "worst" conditions that might be expected as determined from astronomical and satellite measurements, high-speed impact data, and hypothesized meteoroid structures and compositions. It was observed that the vehicle flight time without penetration can be increased significantly by use of multiple-sheet rather than single-sheet hull construction with no increase in hull weight. Nevertheless, it is evident that a meteoroid hazard exists, even for the vehicle with the selected multiple-sheet hull.
Advanced composite materials and designs could eventually be applied as the framework for spacecraft or extraterrestrial constructions for long-term space habitation. One such structure in which NASA has made an investment is the IsoTruss grid structure, an extension of a two-dimensional "isogrid" concept originally developed at McDonnell Douglas Astronautics Company, under contract to NASA's Marshall Space Flight Center in the early 1970s. IsoTruss is a lightweight and efficient alternative to monocoque composite structures, and can be produced in a manner that involves fairly simple techniques. The technology was developed with support from NASA to explore space applications, and is garnering global attention because it is extremely lightweight; as much as 12 times stronger than steel; inexpensive to manufacture, transport, and install; low-maintenance; and is fully recyclable. IsoTruss is expected to see application as utility poles and meteorological towers, for the aforementioned reasons and because its design offers superior wind resistance and is less susceptible to breaking and woodpeckers. Other applications, such as reinforcement for concrete structures, stand-alone towers, sign supports, prostheses, irrigation equipment, and sporting goods are being explored
For almost 100 years, commercial aircraft have been fabricated using riveted aluminum alloy structures. Aside from refining aircraft designs for better aerodynamic efficiency, improving alloy compositions, and automating assembly steps, fuselage construction remains largely unchanged today. The intent of the lightweight metallic fuselage prototype undertaken in NASA’s Advanced Air Transport Technology project was to demonstrate innovative forming and joining processes that advance the design paradigm, i.e. achieve high-rate manufacturing and reduce assembly time/costs. Over the past decade, researchers at NASA Langley Research Center have evaluated the potential to modify the flow forming process to produce near-net shaped cylinders, integrally stiffened along the cylinder axis, for space launch vehicles. The production of integral stiffeners in a formed aluminum cylinder, the size of the Space Shuttle external tank, replaced machined thick plate and welding steps to eliminate > 500,000 pounds of machining chips and ~ 0.5 miles of welds. The flow forming method, called the Integrally Stiffened Cylinder (ISC) process, was successfully demonstrated up to the 10-foot diameter scale, which laid the groundwork for the current investigation of metallic fuselage structures. Using the ISC process as the basis for the re-design of a metallic fuselage eliminates hundreds of thousands of holes and rivets, while significantly reducing assembly time and crack initiation sites in the integral structure. However, the ISC process is not currently configured to fabricate circumferential ring frames for carrying fuselage internal pressure loads. Consequently, a trade study was performed to assess existing and advanced manufacturing processes, including additive manufacturing, forming, and welding. The approach with the lowest barriers to success, while simultaneously improving manufacturing time and cost, was to use formed ring frame segments attached to the ISC via Refill Friction Stir Spot Welding (RFSSW). The RFSSW process is five times faster than drilling, reaming, and riveting and provides similar mechanical performance. Finishing the fuselage structure with conventional windows, floor beams, and floor panels can then be accomplished using incumbent assembly methods, thereby maximizing reuse of existing infrastructure for aircraft construction. Structural analyses were performed to assess and optimize the geometric variables of integrated skin and stiffener configurations. A cost benefit and manufacturing rate analysis was also performed to compare against the current state-of-the-art for single aisle transport class aircraft. The resulting structure offers a weight reduction that rivals current graphite-epoxy composite fuselage structures. The projected manufacturing rate is close to double current metallic fuselages and six times faster than current composite manufacturing practices. The damage tolerance properties of a monocoque fuselage structure have yet to be assessed, but past integral airframe structural work has exploited geometric features to blunt or turn cracks. This concept offers promise that integrated structures can meet stringent aircraft durability specifications. An important benefit is that such aluminum fuselage structures may be inspected and repaired using established practices and existing expertise. Finally, pursuit of advanced manufacturing processes for future aluminum fuselages minimizes waste and the structure is 100% recyclable at the end-of-life for maximum sustainability.