Rigidization of a 1.52-meter diameter inflatable solar concentrator in vacuum with associated material studies and fabrication techniques Final report
Foam rigidizing for inflatable paraboloidal solar collector
FOAMED MATERIAL↗
SEARCH · Search NASA
Results for “Materials studies and techniques”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of a high flow source of energetic oxygen atoms for material degradation studies
A technique for the generation, in the laboratory, of thermally 'cold', high flux of energetic oxygen atoms is presented. The flux of nearly mono-energetic oxygen atoms is obtained after a laser-induced breakdown of oxygen molecules followed by a rapid expansion of the recombining plasma. The experimental apparatus, the optical and spectral measurements, the O-atom source characterization, and the material degradation studies are discussed. Average oxygen atom velocities of about 5 to 13 km/s are measured with an estimated flux of 10 to the 18th per pulse, over pulse durations of several microseconds. The flow of the O2 gas for about 200 microseconds before applying the laser pulse is found to give best results. It is also found that the energetic O-atom irradiation of sample targets such as Al, Fe, and polyethylene, induces mass removal. In addition, spectral scans of the radiation reveals the existence of two main spectral subsets.
Caledonia, G. E.↗
A study of the stress wave factor technique for the characterization of composite materials
This study has investigated the potential of the Stress Wave Factor as an NDT technique for thin composite laminates. The conventional SWF and an alternate method for quantifying the SWF were investigated. Agreement between the initial SWF number, ultrasonic C-scan, inplane displacements as obtained by full field moire interferometry, and the failure location have been observed. The SWF number was observed to be the highest when measured along the fiber direction and the lowest when measured across the fibers. The alternate method for quantifying the SWF used square root of the zeroth moment (square root of M sub o) of the frequency spectrum of the received signal as a quantitative parameter. From this study it therefore appears that the stress wave factor has an excellent potential to monitor damage development in thin composite laminates.
Govada, A. K.↗
Experimental studies in fluid mechanics and materials science using acoustic levitation
Ground-based and short-duration low gravity experiments have been carried out with the use of ultrasonic levitators to study the dynamics of freely suspended liquid drops under the influence of predominantly capillary and acoustic radiation forces. Some of the effects of the levitating field on the shape as well as the fluid flow fields within the drop have been determined. The development and refinement of measurement techniques using levitated drops with size on the order of 2 mm in diameter have yielded methods having direct application to experiments in microgravity. In addition, containerless melting, undercooling, and freezing of organic materials as well as low melting metals have provided experimental data and observations on the application of acoustic positioning techniques to materials studies.
Trinh, E. H.↗
The study of optical properties and collective oscillations in new solid state materials as a function of temperature using infrared and Raman techniques Annual report, 15 May 1969 - 14 May 1970
Optical properties and lattice vibrations of new solid state materials studied by infrared and Raman techniques
Perry, C. H.↗
A study for development of aerothermodynamic test model materials and fabrication technique
A literature survey, materials reformulation and tailoring, fabrication problems, and materials selection and evaluation for fabricating models to be used with the phase-change technique for obtaining quantitative aerodynamic heat transfer data are presented. The study resulted in the selection of two best materials, stycast 2762 FT, and an alumina ceramic. Characteristics of these materials and detailed fabrication methods are presented.
Dean, W. G.↗
A study of molecular contamination
Contamination kinetics of typical space materials were studied using several techniques, including ellipsometry. Data were obtained on contaminant deposition rates, sticking coefficients, and reevaporation of the contamination. Materials studied included silicone sealants, a thermal control paint, and a graphite laminate as contaminant sources, and gold coated surfaces, a thermal control paint and a second surface mirror material as the contaminees. Both deposition and reevaporation rates were found to be nonlinear with time, and followed an exponential decay. A hypothesis is presented that the nonlinear behavior was a result of disproportionation of the molecular weight fractions of the polymers. The measured sticking coefficients were found to vary substantially with temperature over narrow ranges. Simulated space radiation was found to reduce the evaporation rates of contaminants by several orders of magnitude.
Allen, T. H.↗
Low temperature recombination and trapping analysis in high purity gallium arsenide by microwave photodielectric techniques
Some physical theories pertinent to the measurement properties of gallium arsenide are presented and experimental data are analyzed. A model for explaining recombination and trapping high purity gallium arsenide, valid below 77 K is assembled from points made at various places and an appraisal is given of photodielectric techniques for material property studies.
Khambaty, M. B.↗
Friction Pull Plug Welding in Aluminum Alloys
NASA's Marshall Space Flight Center (MSFC) has recently invested much time and effort into the process development of Friction Pull Plug Welding (FPPW). FPPW, is a welding process similar to Friction Push Plug Welding in that, there is a small rotating part (plug) being spun and simultaneously pulled (forged) into a larger part. These two processes differ, in that push plug welding requires an internal reaction support, while pull plug welding reacts to the load externally. FPPW was originally conceived as a post proof repair technique for the Space Shuttle fs External Tank. FPPW was easily selected as the primary weld process used to close out the termination hole on the Constellation Program's ARES I Upper Stage circumferential Self-Reacting Friction Stir Welds (SR-FSW). The versatility of FPPW allows it to also be used as a repair technique for both SR-FSW and Conventional Friction Stir Welds. To date, all MSFC led development has been concentrated on aluminum alloys (2195, 2219, and 2014). Much work has been done to fully understand and characterize the process's limitations. A heavy emphasis has been spent on plug design, to match the various weldland thicknesses and alloy combinations. This presentation will summarize these development efforts including weld parameter development, process control, parameter sensitivity studies, plug repair techniques, material properties including tensile, fracture and failure analysis.
Brooke, Shane A.↗
Friction Pull Plug Welding in Aluminum Alloys
NASA fs Marshall Space Flight Center (MSFC) has recently invested much time and effort into the process development of Friction Pull Plug Welding (FPPW). FPPW, is a welding process similar to Friction Push Plug Welding in that, there is a small rotating part (plug) being spun and simultaneously pulled (forged) into a larger part. These two processes differ, in that push plug welding requires an internal reaction support, while pull plug welding reacts to the load externally. FPPW was originally conceived as a post proof repair technique for External Tank. FPPW was easily selected as the primary process used to close out the termination hole on the Constellation Program fs ARES I Upper Stage circumferential Self ] Reacting Friction Stir Welds (SR ]FSW). The versatility of FPPW allows it to also be used as a repair technique for both SR ]FSW and Conventional Friction Stir Welds. To date, all MSFC led development has been concentrated on aluminum alloys (2195, 2219, and 2014). Much work has been done to fully understand and characterize the process fs limitations. A heavy emphasis has been spent on plug design, to match the various weldland thicknesses and alloy combinations. This presentation will summarize these development efforts including weld parameter development, process control, parameter sensitivity studies, plug repair techniques, material properties including tensile, fracture and failure analysis.
Brooke, Shane A.↗
GSFC micro-volatile condensable materials system for polymer outgassing studies
Instruments and techniques for quantitative analysis of gases and condensables evolved from polymeric spacecraft materials heated in vacuum
Fisher, A.↗
Simulated space environmental effects on a polyetherimide and its carbon fiber-reinforced composites
The selection of materials for spacecraft construction requires identification of candidate materials which can perform reliably in the space environment. Understanding the effects of the space environment on the materials is an important step in the selection of candidate materials. This work examines the effects of energetic electrons, thermal cycling, electron radiation in conjunction with thermal cycling, and atomic oxygen on a thermoplastic polyetherimide and its carbon-fiber-reinforced composites. Composite materials made with non-sized fibers as well as materials made with fibers sized with an epoxy were evaluated. The mechanical and thermomechanical properties of the materials were studied and spectroscopic techniques were used to investigate the mechanisms for the observed effects. Considerations for future material development are suggested.
Kern, Kristen T.↗
An ESCA study of lunar and terrestrial materials.
The technique of electron spectroscopy for chemical analysis (ESCA) is used to obtain rapid, nondestructive elemental analyses of selected lunar samples, and the chemical shift of the Fe(2p) line in lunar materials is found characteristic of iron in the Fe(2+) state. A difference in binding energy of approximately 0.5 eV is observed between the 0(1s) levels of the terrestrial minerals fayalite and quartz, and effects due to surface oxidation and absorption are also observed in terrestrial materials. The new ESCA technique is based on energy analysis at high resolution of electrons emitted from the surface of a sample on irradiation with X rays and is valuable for the study of the electronic structure of atoms and molecules.
Huntress, W. T., Jr.↗
Presolar/Interstellar Materials
This talk will review much of our current understanding of the origins, nature, and evolution of materials in circumstellar and interstellar space. I will begin by familiarizing the audience with some of the nomenclature associated the field, reviewing the lifecycle of dust in space, and pointing out where the speakers that follow will address portions of the lifecycle in greater detail. I will then address the different techniques used to study interstellar materials, paying particular attention to (i) telescopic remote sensing of the dust currently in interstellar space, (ii) laboratory studies of individual interstellar grains found in meteorites and other extraterrestrial materials, and (iii) laboratory simulation experiments. To complete the talk, I will focus on the nature of interstellar organic compounds as a particular example of how these disparate techniques can be used to improve our understanding of interstellar matter. While interstellar organics will be addressed in general, particular attention will be made to that portion of the organic inventory that may play a role in the origin and evolution of life on planetary surfaces.
Sandford, Scott A.↗
Application of the Moessbauer technique to the study of probable lunar and planetary surface material and to the study of returned lunar surface samples Final report
Preliminary results from Mossbauer instrumental analysis of Apollo 12 lunar rock and soil samples
Herzenberg, C. L.↗
Application of remote sensing to monitoring and studying dispersion in ocean dumping
Remotely sensed wide area synoptic data provides information on ocean dumping that is not readily available by other means. A qualitative approach has been used to map features, such as river plumes. Results of quantitative analyses have been used to develop maps showing quantitative distributions of one or more water quality parameters, such as suspended solids or chlorophyll a. Joint NASA/NOAA experiments have been conducted at designated dump areas in the U.S. coastal zones to determine the applicability of aircraft remote sensing systems to map plumes resulting from ocean dumping of sewage sludge and industrial wastes. A second objective is related to the evaluation of previously developed quantitative analysis techniques for studying dispersion of materials in these plumes. It was found that plumes resulting from dumping of four waste materials have distinctive spectral characteristics. The development of a technology for use in a routine monitoring system, based on remote sensing techniques, is discussed.
Johnson, R. W.↗
Heating And Positioning In A Microwave Cavity
Two reports describe theoretical and experimental studies of microwave dielectrophoretic positioning of spherical sample of lossy dielectric material in microwave resonant cavity and heating of positioned sphere by electro-magnetic field. Studies part of continuing effort to develop techniques for containerless processing of materials in microgravity. Previous studies in this series described in "Microwave Dielectrophoretic Levitation in Microgravity" (NPO-18824).
Jackson, Henry W.↗
A study of the stress wave factor technique for evaluation of composite materials
The acousto-ultrasonic approach for nondestructive evaluation provides a measurement procedure for quantifying the integrated effect of globally distributed damage characteristic of fiber reinforced composite materials. The evaluation procedure provides a stress wave factor that correlates closely with several material performance parameters. The procedure was investigated for a variety of materials including advanced composites, hybrid structure bonds, adhesive bonds, wood products, and wire rope. The research program focused primarily on development of fundamental understanding and applications advancements of acousto-ultrasonics for materials characterization. This involves characterization of materials for which detection, location, and identification of imperfections cannot at present be analyzed satisfactorily with mechanical performance prediction models. In addition to presenting definitive studies on application potentials, the understanding of the acousto-ultrasonic method as applied to advanced composites is reviewed.
Duke, J. C., Jr.↗