SEARCH · Search NASA
Results for “Microwave heating”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Microwave heated chemical looping ammonia synthesis over Fe and CoMo particles
Chemical looping ammonia synthesis (CLAS) materials were subjected to a three cycle ammonia synthesis test under both conventional thermal heating and microwave heating. Microwave heating was found to outperform conventional heating for the first cycle on both Fe and CoMo materials. Principles of microwave catalysis and the heating of metallic particles may be generalized from this study; the dielectric loss tangent for optimum heating must fall within a realtively small range, ~0.8–1.4, and the penetration depth of the microwave into the particle must be considered and optimized for efficient heating, penetration depth should be on the same order as the particle size. The active phases of both catalysts, Fe 4 N and Co 3 Mo 3 N, were found to be responsive to microwave irradiation. Lastly, the deactivation and regeneration of the materials was studied by examining the BET surface areas by reforming surfaces with a low concentration gas phase oxidation reaction. This study sheds light on more general principles of microwave catalysis and on the scale-up of CLAS reactions.
Oxidative ethane dehydrogenation under thermal vs. microwave heating over Ga/ZSM-5 and GaPt/ZSM-5
Conventional thermal heating versus microwave heating for the oxidative dehydrogenation of ethane with CO 2 as the oxidative co-reactant over 2%Ga/ZSM-5 and 1.5%Ga0.5%Pt/ZSM-5. The Ga/ZSM-5 and GaPt/ZSM-5 had a similar ethane conversion under microwave heating at 450 °C, compared to the thermally heated catalyst at 650 °C. The bimetallic GaPt/ZSM-5 performed better than the Ga/ZSM-5. Both the GaPtMWFB-450 °C and GaMWFB-450 °C resulted in a lower production rate to carbon monoxide and water than the TFB-650 °C, suggesting that the microwave heating is less favorable to the water gas shift reaction. In this study, microwave heating increased the catalytic conversion of ethane and selectivity to ethylene.
Temperature Homogeneity under Selective and Localized Microwave Heating in Structured Flow Reactors
Selective heating of different phases of multiphase systems via microwaves can result in energy savings and suppression of side reactions. However, materials properties and operating conditions that maximize temperature gradients are poorly understood. Here we utilize computational fluid dynamics (CFD) computations and temperature measurements in structured flow reactors (monoliths) in a monomodal microwave cavity to assess the temperature difference between the walls and the fluid and develop a simple lumped model to estimate when temperature gradients exist. We also explore the material’s thermal and electrical properties of structured reactors for isothermal catalyst conditions. We propose that CFD simulations can be used as a nonintrusive, predictive tool of temperature homogeneity. Importantly, we demonstrate that localized heating in the bed under several conditions rather than selective heating is responsible for the selectivity enhancement. Furthermore, our results indicate that structured beds made of high thermal conductivity materials avoid arcing and enable temperature homogeneity and low electrical conductivity materials allow microwaves to penetrate the domain.
Multiscale modeling of microwave-heated multiphase systems
Modeling of microwave heating of multiphase systems requires resolving the electromagnetic field from the single particle to the entire cavity. We introduce a multiscale methodology for computationally affordable simulations of microwave heating of multiphase systems consisting of one phase dispersed in a continuum phase. The methodology homogenizes the original multiphase system, by taking advantage of the large separation of length scales, to calculate the effective permittivity, effective thermal conductivity, and volumetric power absorbed in each phase. The methodology is rigorously assessed against particle-resolved detailed numerical simulations of model systems. We demonstrate a significant reduction in computational cost while retaining the accuracy of detailed simulations. Lastly, the present methodology enables high throughput exploration of novel multiphase system designs utilizing microwave heating.
Modeling the Effects of Microwave Heating on Densification in Chemical Vapor Infiltration
Microwave heating has great potential to accelerate the synthesis of ceramic matrix composites (CMCs) by a process called Chemical Vapor Infiltration (CVI). In CVI, reactive gases ingress a porous preform and undergo chemical transformation to deposit solid ceramic phase within the pores at high temperature thus, densifying the preform. However, the competing effects of chemical kinetics and gas transport are known to result in non-uniform densification as the outer surfaces of the preform experience faster depositions compared to the core. Achieving spatial temperature control plays a key role improving the densification quality. Microwave heating can potentially create temperature inversion such that the core of the preform is hotter than the outer surface and subsequently, lead to improved densification while keeping the manufacturing times and costs low. In the present work, a computational modeling strategy has been developed that accounts for the key physical phenomena responsible for densification of porous preforms using microwave heating. Specifically, a chemical kinetics model has been formulated for Silicon Carbide (SiC) deposition from MTS/H2 precursor. The model is implemented in a pore-resolved reactive transport solver, Quilt. The CVI simulations are performed for several conditions. Initially, parameterized temperature control is imposed to identify optimum conditions for good densification quality at a fraction of processing time. Further, simulations of microwave heating of porous SiC preforms are performed using OpenFOAM. A strategy to achieve and enhance temperature inversion is identified. The resulting temperature profiles are used in the pore-resolved densification simulations to analyze the densification behavior. It is observed that the temperature inversion achieved by microwave heating leads to significant improvements in densification quality and at the same time, keeps the manufacturing time low.
Reduced graphene oxide catalytically enhances the rate of cyanate ester curing under variable frequency microwave heating
Here, the curing of Lonza Primaset PT-30 novolac cyanate ester resin and EPON 826 bisphenol-A diglycidyl ether were investigated using convective thermal heating and variable frequency microwave (VFM) heating. The addition of 1 part per hundred reduced graphene oxide (r-GO) to PT-30 novolac cyanate ester increased the VFM cure rate compared to thermal heating. Curing it at 160°C for 240 min with VFM heating resulted in a 55% degree of cure compared to a 26% degree of cure with thermal heating. This observed VFM rate enhancement is due to selective microwave heating of the r-GO particles in the resin resulting in increased r-GO catalytic activity toward cyanate ester curing. It is both a thermal and catalytic effect, the latter of which is absent when r-GO is added to a bisphenol-A diglycidyl ether resin with o-phenylenediamine hardener. Impurities present in the PT-30 matrix do not appear to contribute to its overall cure kinetics, nor do they participate in the observed VFM rate enhancement.
Carbon Nanotube Supported Amorphous MoS 2 via Microwave Heating Synthesis for Enhanced Performance of Hydrogen Evolution Reaction
Amorphous molybdenum disulfide (MoS 2 ) is a promising electrochemical catalyst for hydrogen evolution reaction (HER) due to more active sites exposed on the surface compared to its crystalline counterpart. In this study, a novel fast three-minute one-pot method is proposed to prepare the single-wall carbon nanotube- (SWCNT-) supported amorphous MoS 2 via a microwave heating process. Compared to traditional hydro- or solvent thermal methods to prepare MoS 2 which usually consume more than 10 hours, it is more promising for fast production. An overpotential at 10 mA/cm 2 of amorphous MoS 2 @SWCNT is 178 mV, which is 99 mV and 22 mV lower than crystalline MoS 2 @SWCNT and pure amorphous MoS 2 , respectively. After running 1000 cycles of polarization, ~2% increase in overpotential is observed, indicating its good stability. The enhanced performance results from the beneficial combination of the SWCNT substrate and the amorphous microstructures. The introduction of SWCNT increases catalyst conductivity and prevents MoS 2 aggregation. The amorphous microstructures of MoS 2 prepared by a microwave heating method lead to more Mo edges or active sites exposed.
Operation and Optimization of Microwave-Heated Continuous-Flow Microfluidics
Microwave (MW) technology can be powerful for electrification and process intensification but limited fundamental understanding of scalability and design principles hinders its effective use. In this work, we build a continuous-flow microreactor inside a commercial single-mode MW applicator and the corresponding computational fluid dynamics model to simulate the temperature profile. The model is in good agreement with experiments for various microreactor dimensions and operating conditions. The model indicates that MW heating is greatly influenced by reactor geometry as well as the operating parameters. We observe a strong correlation between parameters and develop a gradient boost regression tree model to predict the outlet temperature accurately. This model is then applied to optimize the dimensions and operating conditions to maximize the outlet temperature and energy efficiency, resulting in a Pareto optimal. We demonstrate computationally and experimentally that it is possible to surpass the Pareto optimal and achieve an energy efficiency of ~90% or greater at temperatures relevant for liquid-phase chemistry via salting of the solvent. The present methodology can be applied to other complex MW reactors. Lastly, the combined numerical and experimental approach provides insights into and a framework for scale-up and optimization.
Chemical recycling of polymer composites induced by selective variable frequency microwave heating
Abstract The application of variable frequency microwave (VFM) heating to achieve rapid thermal depolymerization of polymer composites is reported for the first time. The thermal and chemical influence of composite additives on polymer decomposition has been studied for a set of chemically recyclable polymers, including polyphthalaldehyde, polypropylene carbonate, two polyhydroxyalkanoates, and nylon 6. Carbon‐based additives, specifically nanocarbon particles, were used as effective microwave absorbers to controllably degrade the surrounding polymer matrix into valuable, monomeric compounds. Depolymerization and byproduct confirmation were quantified by gel permeation chromatography and nuclear magnetic resonance spectroscopy. Synergistic effects can be leveraged from pre‐treating composite samples to further reduce the total microwave energy required to depolymerize composite samples. This study establishes the use of VFM heating for chemical recycling of polymer composites that can be leveraged toward a plastic circular economy.
Broadening of microwave heating beams in the DIII-D tokamak by edge turbulence
Abstract We have demonstrated for the first time that turbulent plasma density fluctuations in the edge of the DIII-D tokamak are responsible for substantial broadening of an injected microwave beam by successful quantitative comparison between experimental observations and first principles 2D full-wave simulations. The broadening of the beam has important implications for control of tokamak discharges through localized electron cyclotron deposition needed for eliminating magnetohydrodynamic instabilities. This new predictive capability is mandatory to design & operate present & future tokamaks in such a way that microwave heating schemes achieve their intended objectives.
Insight into Enhanced Microwave Heating for Ammonia Synthesis: Effects of CNT on the Cs–Ru/CeO 2 Catalyst
Not Available
Microwave Heating of Nanocrystals for Rapid, Low-Aggregation Intermetallic Phase Transformations
The use of intermetallic Pt–Co nanocrystals (NCs) for the electrocatalytic oxygen reduction reaction is quickly gaining interest thanks to the higher electrochemical stability of the intermetallic L1 o phase compared to a random alloy A1 phase. However, the thermal treatment that enables the intermetallic phase transformation also causes considerable NC aggregation, resulting in a significant loss of electrochemically active surface area. Herein, we report the use of microwave radiation to induce the intermetallic phase transformation in Cu-doped Pt–Co NCs. We demonstrate that microwave radiation reduces NC aggregation while allowing for a complete phase transformation in only 30 s. Furthermore, these microwave-treated NCs demonstrate higher mass activity for the oxygen reduction reaction while maintaining electrochemical stability similar to the thermally annealed samples.
Extracting Critical Metals from Authentic Bauxite Residue
Securing domestic sources of critical minerals (CM) is paramount to ensuring a robust and self-sustaining technology infrastructure. Utilizing untapped non-conventional sources, like acid mine drainage, coal ash, bauxite residue/red mud, and more is an emerging approach that addresses this national concern while identifying new value-added pathways originating from waste streams. Red mud is a byproduct of the Bayer process that produces alumina and contains a wealth of CM – 50 µg/g Ga, 2.9 mg/g total rare earth elements plus yttrium, 12 mg/g Mn, 58 mg/g Al, and others. About 170 MM tonnes of red mud are co-produced annually alongside the 142 MM tonnes of alumina generated, highlighting the abundancy of this feedstock. In this work, different strategies were explored for extracting CM from authentic bauxite residue that involve thermal heating, microwave heating, and sonication all with different acids and buffers. CM recovery was then explored one step further by testing the adsorption of the extracted metals onto NETL’s Multi-functional Sorbent Technology (MUST). Microwave treatment of red mud proved the most effective CM extraction, whereas sonication was less desirable due to scale-up concerns. Successful recovery of CM from this leachate with MUST supports further studies toward optimizing the overall process.
A Review of Microwave-Assisted Synthesis-Based Approaches to Reduce Pd-Content in Catalysts
This review article focuses on the latest advances in the synthesis of inorganic nano-catalysts using microwave heating, which has progressed significantly since its initial implementation in the mid-1980s. Over the years, nanoparticles (NPs), which inherently offer better surface accessibility for heterogeneous catalysis, have been synthesized using a wide array of heating methods. Microwave heating is one such method and employs a unique heating mechanism that can have several benefits for catalysis. When compared to conventional form of heating which relies on inter-layer mixing via convection, microwave heating operates through the chemical polarity in the target chemicals leading to an “inside-out” mode of heating. This heating mechanism is more targeted and therefore results in rapid synthesis of catalytically active NPs. Platinum group metals (PGM) have classically been the focus of nano-catalysis; however, recent efforts have also applied non-PGM group metals with the goals of lower costs, and ideally, improved catalytic reactivity and durability. This is especially of interest with respect to Pd because of its current historically high cost. Investigations into these new materials have primarily focused on new/improved synthetic methods and catalytic compositions, but it is important to note that these approaches must also be economic and scalable to attain practical relevance. With this overarching goal in mind, this review summarizes notable recent findings with a focus on Pd-dilution and microwave heating in a chronological fashion.
Microwave-Assisted Heating for Gasification
Compared to traditional heating, microwave-assisted heating enhances catalyst activity, selectivity and stability. These features are essential in gasification to improve the process outcome while mitigating the generation undesirable by-products such as char. To study the effect of microwaves on fluidized bed reactors, the electromagnetics module of COMSOL and MFiX are coupled using file input/output wherein external calls are made to COMSOL from MFiX. The particle bed heating rates and temperature distributions are investigateed in the case of a monodisperse bed of magnetite particles subjected to single mode transverse electric and magnetic fields in reacting and non-reacting conditions. The effect of inlet gas velocity on the heating rate of particle is also explored in this work.
Microwave Heating-Induced Temperature Gradients in Liquid–Liquid Biphasic Systems
Microwaves (MWs) can enable the electrification and intensification of chemical manufacturing. They have been applied to various unit separations, such as drying, distillation, and extraction, entailing gas–liquid and solid–liquid systems. However, a limited quantitative understanding of MW-heated liquid–liquid biphasic systems related to extraction exists. This work measures the temporal and spatial temperature difference between an aqueous and an organic phase in batch and continuous microfluidic modes. We demonstrate permanent temperature differences between phases over 35 °C and spatiotemporal periodic and quasiperiodic oscillations modulated by the flow patterns. The temperature differences are primarily driven by the faster absorption rate of MW irradiation by the aqueous phase versus the slower heat transfer from the aqueous phase to the organic phase. These are amplified by low specific interfacial area and modifications of the electromagnetic field. We employ a multiphysics model to predict the temperature difference in a batch system. The model is in good agreement with the experiments. We demonstrate a strong effect of input power, dielectric properties of organic solvents, the volume of solvents, and the volume ratio between phases on the temperature difference. A simple analytical model describes the temperature difference and provides design principles. Furthermore, the combined approach offers new insights into the design and optimization of the MW-heated biphasic systems.
Direct Measurement of the Selective Microwave-Induced Heating of Agglomerates of Dipolar Molecules: The Origin of and Parameters Controlling a Microwave Specific Superheating Effect
Agglomerates of polar molecules in nonpolar solvents are selectively heated by microwave radiation. The magnitude of the selective heating was directly measured by using the temperature dependence of the intensities of the Stokes and anti-Stokes bands in the Raman spectra of p-nitroanisole (pNA) and mesitylene. Under dynamic heating conditions, a large apparent temperature difference (ΔT) of over 100 °C was observed between the polar pNA solute and the nonpolar mesitylene solvent. This represents the first direct measurement of the selective microwave heating process. The magnitude of the selective microwave heating was affected by the properties of the agglomerated pNA. As the concentration of the pNA increases, the magnitude of the selective heating of the pNA was observed to decrease. This is explained by the tendency of the pNA dipoles to orient in an antiparallel fashion in the aggregates as measured by the Kirkwood g value, which decreased with increasing concentration. This effect reduces the net dipole moment of the agglomerates, which decreases the microwave absorption. After the radiation was terminated, the effective temperature of the dipolar molecules returned slowly to that of the medium. The slow heat transfer was modeled successfully by treating the solutions as a biphasic solvent/solute system. Based on modeling and the fact that the agglomerate can be heated above the boiling temperature of the solvent, an insulating layer of solvent vapor is suggested to form around the heated agglomerate, slowing convective heat transfer out of the agglomerate. Furthermore, this is an effect unique to microwave heating.