SEARCH · Search NASA
Results for “MnO2”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Optimization of Hydrogels for non-spillable Zn|MnO2 rechargeable batteries allowing for 2nd electron MnO2 cycling.
Abstract not provided.
Use of Hydrogel Electrolyte in Zn-MnO2 Rechargeable Batteries: Characterization of Safety, Performance, and Cu2+ Ion Diffusion
Achieving commercially acceptable Zn-MnO2 rechargeable batteries depends on the reversibility of active zinc and manganese materials, and avoiding side reactions during the second electron reaction of MnO2. Typically, liquid electrolytes such as potassium hydroxide (KOH) are used for Zn-MnO2 rechargeable batteries. However, it is known that using liquid electrolytes causes the formation of electrochemically inactive materials, such as precipitation Mn3O4 or ZnMn2O4 resulting from the uncontrollable reaction of Mn3+ dissolved species with zincate ions. In this paper, hydrogel electrolytes are tested for MnO2 electrodes undergoing two-electron cycling. Improved cell safety is achieved because the hydrogel electrolyte is non-spillable, according to standards from the US Department of Transportation (DOT). The cycling of “half cells” with advanced-formulation MnO2 cathodes paired with commercial NiOOH electrodes is tested with hydrogel and a normal electrolyte, to detect changes to the zincate crossover and reaction from anode to cathode. These half cells achieved ≥700 cycles with 99% coulombic efficiency and 63% energy efficiency at C/3 rates based on the second electron capacity of MnO2. Other cycling tests with “full cells” of Zn anodes with the same MnO2 cathodes achieved ~300 cycles until reaching 50% capacity fade, a comparable performance to cells using liquid electrolyte. Electrodes dissected after cycling showed that the liquid electrolyte allowed Cu ions to migrate more than the hydrogel electrolyte. However, measurements of the Cu diffusion coefficient showed no difference between liquid and gel electrolytes; thus, it was hypothesized that the gel electrolytes reduced the occurrence of Cu short circuits by either (a) reducing electrode physical contact to the separator or (b) reducing electro-convective electrolyte transport that may be as important as diffusive transport.
Direct Conversion of MnO2 into Atomic Mn Sites for Oxygen Reduction
Development of platinum group metal (PGM)-free catalysts has been investigated to replace the platinum group metal catalyst in future inexpensive polymer electrolyte membrane (PEM) fuel cells. Usually, synthetic methods for these PGM-free catalysts involve introducing transition-metal salts or molecules. Herein, we demonstrate a facile synthetic method to prepare PGM-free Mn-N-C catalysts by directly converting manganese oxides into highly active MnN4 sites. Typically, MnO2 is used as a Mn source. Ammonium chloride and benzimidazole are introduced during high-temperature treatment to enhance catalytic activity and stability further. Ammonia generated from the decomposition of ammonium chloride can improve the intrinsic ORR activity of MnNx moieties through chemical or electronic effects by introducing additional nitrogen groups. The Mn-N-C catalyst exhibits promising ORR activity, achieving a half-wave potential of 0.83 V in 0.5 M H2SO4, outperforming most PGM-free ORR catalysts. The robust carbon structure resulting from organic-molecule treatment is also verified by electrochemical and physical characterization, thereby improving the catalyst's durability.
Oxidative Electrochemical Coupling Between Bi and Mn in Rechargeable Alkaline MnO2 Cathodes
Explore the source record for details and available documents.
Analysis of Battery Testing Protocols in the Transition from the Lab to the Field: A Test Case Using Advanced Zn-MnO2 Batteries in Off-Grid Solar Microgrids
Explore the source record for details and available documents.
Discharging Behavior of Hollandite α-MnO2 in a Hydrated Zinc-Ion Battery
Explore the source record for details and available documents.
Non-destructive electrochemical diagnosis of failure mechanisms in aqueous zinc batteries
The early detection of secondary reactions that affect the life and performance of zinc manganese oxide batteries requires a shift from conventional time-consuming and often destructive procedures to rapid lifetime-predictive techniques. In this work, an electrochemical approach is employed to elucidate independent signatures for four common types of failure mechanisms in zinc manganese dioxide (Zn||MnO2) batteries—namely, the loss of zinc inventory, the loss of active material at the cathode, electrolyte depletion, and increased cell impedance. Our findings, specific to coin cell configurations, reveal that each induced failure mechanism can be distinctively modeled and identified based on responses from the rest voltage and columbic-efficiency data for prompt detection. For instance, electrolyte depletion response manifests a distinctive abrupt (>80 %) decrease in columbic efficiency (CE) and charge-rest voltage (Vc) while the discharge-rest voltage remained constant at ~1.3 V. Furthermore, electrolyte rejuvenation of the cell increased the CE to >95 % and restored Vc from ~0.3 to >1.7 V. Recovery experiments and reference performance tests demonstrated consistency between electrochemical descriptors and their associated failure mechanisms. Further, the outcomes of this work provide valuable insights and data models for some of the dominant failure mechanisms present in zinc manganese battery chemistries, which are beneficial to accelerated early-lifetime diagnosis and advancement of Zn batteries development.
Spatial and chemical heterogeneity in aqueous Zn/MnO 2 batteries: role of Zn and Mn containing complexes
Aqueous Zn/MnO 2 batteries are a promising, safe alternative for grid-scale energy storage, owing to their environmentally safe and low-cost nature. The dissolution–deposition reaction mechanism in a mild aqueous pH regime has recently gained significance due to its relevance in battery design. Comprehending both the specific locations and the way reaction progresses is crucial for efficient batteries. This study demonstrates that Zinc Hydroxy Sulfate (ZHS) formed during discharge primarily near the dissolved MnO2 particles. Acting as a host for charge reactants in subsequent cycles, the charge product morphology was visualized using operando X-ray fluorescence microscopy. After ∼400 hours of cycling, capacity fade was linked to the formation of a Zn–Mn core–shell phase which is attributed to an irreversible core phase in the electrode, visualized through three-dimensional chemical mapping. Altogether, this research underscores the importance of understanding local morphological evolution in designing electrodes and chemistries for advanced grid-scale energy storage technologies.
Microbial Reduction of Manganese Oxides From AMD Solids for the Biomining of Critical Minerals / Rare Earth Elements
Abandoned Coal-Mine Drainage (AMD) is a source of critical minerals (CMs) that can be biomined to increase domestic CM production for the growing tech industry while mitigating current AMD hazardous waste. Pennsylvania has ~11,000 abandoned mines, ~500 of which are currently being treated with passive remediation systems (PRS), designed to increase the pH and precipitate AMD waste onsite. Manganese (Mn) that precipitates from AMD waste can co-precipitate with CMs, and the Mn and CMs will accumulate on the PRS solids over the treatment period. This results in high Mn/CM solids that could produce a valuable leachate if resolubilized. Mn reduction and solubilization can occur through microbial driven geochemical changes such as the acidification of the environment, and it is expected that Mn resolubilization will lead to a co-resolubilization of the CMs. Investigation and stimulation of this microbial resolubilization could result in an affordable CM release process that does not require chemical additives into the environment. However the microbial mechanisms that contribute to Mn resolubilization are poorly understood. Here, we have isolated bacteria capable of resolubilizing Mn from AMD PRS. Five of the bacteria isolates have been identified as Bacillus spp. and two as Corynebacterium spp. that ferment glucose to reduce/solubilize Mn MnO2 by acidogenesis. The bacterial isolates are also capable of solubilizing Mn and CMs (Y, Zr, Sb, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu) from AMD PRS precipitated solids through their production of organic acids. Determining the microbial metabolism and genes involved in the resolubilization of manganese is crucial to optimize the biomining of CMs from AMD solid precipitants. This work addresses the growing need to develop novel CM recovery methods from domestic sources.
High waste loading glass formulation development for High-Mn HLW
One of the primary objectives of the work described herein was to develop and identify HLW glass compositions and glass forming additive blends that achieve high waste loadings and processing rates for high manganese HLW streams while maintaining acceptable glass properties. Another objective was to determine the effect of the form of manganese (MnO, MnO2, MnCO3) on feed processing properties, glass production rates, and product quality while vitrifying a high manganese HLW stream. This was accomplished through a combination of crucible-scale tests, vertical gradient furnace tests, and confirmation tests on a DM100 melter system.
Ultrahigh-Loading Manganese-Based Electrodes for Aqueous Batteries via Polymorph Tuning
Manganese-based aqueous batteries utilizing Mn 2+ /MnO 2 redox reactions are promising choices for grid-scale energy storage due to their high theoretical specific capacity, high power capability, low-cost, and intrinsic safety with water-based electrolytes. However, the application of such systems is hindered by the insulating nature of deposited MnO 2 , resulting in low normalized areal loading (0.005–0.05 mAh cm -2 ) during the charge/discharge cycle. Here, in this work, the electrochemical performance of various MnO 2 polymorphs in Mn 2+ /MnO 2 redox reactions is investigated, and ε-MnO 2 with low conductivity is determined to be the primary electrochemically deposited phase in normal acidic aqueous electrolyte. It is found that increasing the temperature can change the deposited phase from ε-MnO 2 with low conductivity to γ-MnO 2 with two order of magnitude increase in conductivity. It is demonstrated that the highly conductive γ-MnO 2 can be effectively exploited for ultrahigh areal loading electrode, and a normalized areal loading of 33 mAh cm -2 is achieved. At a mild temperature of 50 °C, cells are cycled with an ultrahigh areal loading of 20 mAh cm -2 (1–2 orders of magnitude higher than previous studies) for over 200 cycles with only 13% capacity loss.
Rational optimization of substituted α–MnO 2 cathode for aqueous zinc–ion battery
Density functional theory (DFT) is utilized to explore the effects of increasing concentrations of vanadium (V) and chromium (Cr) substitution on the discharge of α-MnO 2 cathode in hydrated zinc-ion batteries (ZIBs). During H + -intercalation and Zn 2+ -intercalation, Cr-substitution proves to be more effective than V-substitution in promoting discharge behaviors. Transitioning from Mn 0.875 Cr 0.125 O 2 , Mn 0.75 Cr 0.25 O 2 to Mn 0.625 Cr 0.375 O 2 is found to consistently enhance the discharge voltage, along with improved tunnel structure retention and volume expansion suppression. In comparison, the promoting effect of increasing V-substitution is relatively small at initial discharge stages and leads to degradation at later stages, primarily due to an increased concentration of unstable Mn 2+ ion. The superior effect of Cr-substitution is attributed to the unique atomic and electronic structures of substituted Cr 4+ and reduced Cr 3+ ions during discharge. These ions serve as active electron acceptors to limit the formation of Mn 3+ and Mn 2+ ions, and as anchors to stabilize the α-MnO 2 framework and intercalated H + /Zn 2+ ions, respectively. Finally, our study highlights fine-tuning through substitution to enhance the performance of α-MnO 2 -based cathode materials in ZIBs.
A comprehensive study on two types of supercapacitor composite electrodes comprising MnO 2 and activated carbon nanofibers: Self-supporting membrane and ground powder
Manganese dioxide (MnO 2 )@carbon composites have been attractively considered as electrode materials for supercapacitors (SCs) due to synergistic effects. This work systematically investigated the structure of MnO 2 @carbon nanofiber (CNF) composite electrodes with the different forms of CNFs and the corresponding electrochemical performance of SCs. In brief, novel activated carbon nanofibers were first fabricated by electrospinning the hydroxyl-containing poly(amic acid) solution, and then the preferred CNF material was decorated by MnO 2 crystals in the form of self-supporting membrane and ground powders, respectively. Additionally, the synthesis parameters were investigated and optimized based on the electrochemical performance of SCs. The results reveal that the powdered composite electrode exhibits a higher specific surface area of 501 m 2 g –1 compared to the self-supporting membrane composite electrode under the same conditions, resulting in a promising specific capacity of 214.1 mAh g –1 (770.8 Fg –1 ) in 6M KOH solution at 0.5 A g –1 . In addition, the capacitance of the symmetrical SC device assembled by G-HMC-1:3–80 reaches 179.8 Fg –1 , coupled with an energy density of 24.86 Whkg –1 at 230 Wkg –1 power density. This work provides valuable hints for designing SC composite electrode materials with outstanding performance.
Calorimetry can detect the early onset of hydrolysis in hybrid supercapacitors with aqueous electrolytes
This study investigates the effect of cation species on the onset of electrolyte hydrolysis in hybrid supercapacitors with aqueous electrolytes using isothermal operando calorimetry. The cells consisted of a positive α-MnO 2 cryptomelane electrode and a negative activated carbon (AC) electrode with either 0.5 M K 2 SO 4 or 0.5 M Cs 2 SO 4 aqueous electrolytes. They were characterized using cyclic voltammetry and galvanostatic cycling. In addition, the instantaneous heat generation rate at each electrode was measured using a custom isothermal operando calorimeter. Heat generation associated with resistive losses (Joule heating) and reversible ion adsorption/desorption was clearly identified. For larger potential windows, an endothermic dip, attributed to the onset of hydrolysis, was observed at the positive α-MnO 2 electrode where K + and Cs + ions engaged in fast surface redox reactions. Interestingly, this endothermic dip appeared at 1.8 V and 2.0 V for K 2 SO 4 and Cs 2 SO 4 aqueous electrolytes, respectively. The difference in the stable operating potential window was attributed to thinner solvation shell around Cs + cation than for K + thus reducing the amount of water present near the electrodes as ions partially shed their solvation shells during adsorption. The early onset of hydrolysis could be observed by isothermal operando calorimetry before it could be observed with conventional electrochemical methods.
Mn(III)-mediated bisphenol a degradation: Mechanisms and products
Bisphenol A (BPA) is a high production volume chemical with potential estrogenic effects susceptible to abiotic degradation by MnO 2 . BPA transformation products and reaction mechanisms with MnO 2 have been investigated, but detailed process understanding of Mn(III)-mediated degradation has not been attained. Rapid consumption of BPA occurred in batch reaction vessels with 1 mM Mn(III) and 63.9 ± 0.7% of 1.76 ± 0.02 μmol BPA was degraded in 1 hour at circumneutral pH. BPA was consumed at 1.86 ± 0.09-fold higher rates in vessels with synthetic MnO 2 comprising approximately 13 mol% surface-associated Mn(III) versus surface-Mn(III)-free MnO 2 , and 10–35% of BPA transformation could be attributed to Mn(III) during the initial 10-min reaction phase. High-resolution tandem mass spectrometry (HRMS/MS) analysis detected eight transformation intermediates in reactions with Mn(III), and quantum calculations proposed 14 BPA degradation products, nine of which had not been observed during MnO 2 -mediated BPA degradation, suggesting mechanistic differences between Mn(III)- versus MnO 2 -mediated BPA degradation. Finally, the findings demonstrate that both Mn(III) and Mn(IV) can effectively degrade BPA and indicate that surface-associated Mn(III) increases the reactivity of synthetic MnO 2 , offering opportunities for engineering more reactive oxidized Mn species for BPA removal.
Robust Interfacial Effect in Multi-interface Environment through Hybrid Reconstruction Chemistry for Enhanced Energy Storage
Electrochemical-oxidation-driven reconstruction has emerged as an efficient approach for developing advanced materials, but the reconstructed microstructure still faces challenges including inferior conductivity, unsatisfying intrinsic activity, and active-species dissolution. In this report we present hybrid reconstruction chemistry that synergistically couples electrochemical oxidation with electrochemical polymerization (EOEP) to overcome these constraints. During the EOEP process, the metal hydroxides undergo rapid reconstruction and dynamically couple with polypyrrole (PPy), resulting in an interface-enriched microenvironment. We observe that the interaction between PPy and the reconstructed metal center (i.e., Mn > Ni, Co) is strongly correlated. Theoretical calculation results demonstrate that the strong interaction between Mn sites and PPy breaks the intrinsic limitation of MnO 2 , rendering MnO 2 with a metallic property for fast charge transfer and enhancing the ion-adsorption dynamics. Operando Raman measurement confirms the promise of EOEP-treated Mn(OH) 2 (E-MO/PPy) to stably work under a 1.2 V potential window. The tailored E-MO/PPy exhibits a high capacitance of 296 F g –1 at a large current density of 100 A g –1 . Here our strategy presents breakthroughs in upgrading the electrochemical reconstruction technique, which enables both activity and kinetics engineering of electrode materials for better performance in energy-related fields.