Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mode filter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Adaptive Control of Flexible Structures Using Residual Mode Filters

Flexible structures containing a large number of modes can benefit from adaptive control techniques which are well suited to applications that have unknown modeling parameters and poorly known operating conditions. In this paper, we focus on a direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend our adaptive control theory to accommodate troublesome modal subsystems of a plant that might inhibit the adaptive controller. In some cases the plant does not satisfy the requirements of Almost Strict Positive Realness. Instead, there maybe be a modal subsystem that inhibits this property. This section will present new results for our adaptive control theory. We will modify the adaptive controller with a Residual Mode Filter (RMF) to compensate for the troublesome modal subsystem, or the Q modes. Here we present the theory for adaptive controllers modified by RMFs, with attention to the issue of disturbances propagating through the Q modes. We apply the theoretical results to a flexible structure example to illustrate the behavior with and without the residual mode filter. We have proposed a modified adaptive controller with a residual mode filter. The RMF is used to accommodate troublesome modes in the system that might otherwise inhibit the adaptive controller, in particular the ASPR condition. This new theory accounts for leakage of the disturbance term into the Q modes. A simple three-mode example shows that the RMF can restore stability to an otherwise unstable adaptively controlled system. This is done without modifying the adaptive controller design.

Balas, Mark J.↗
DOE OSTI2023

A new efficient grain growth model using a random Gaussian-sampled mode filter

This paper presents the use of a Gaussian neighborhood mode filter for predicting grain growth in a manner similar to the solutions obtained by a Monte Carlo Potts model. This flexible grain growth model can quickly utilize modern, computationally optimized data science strategies on graphics processing units to simulate grain growth up to 100 times faster than the state-of-the-art, publicly available Monte Carlo Potts model. We show that, given the correct neighborhood, the mode filter can replicate normal grain growth in two or three dimensions. In addition, the paper briefly demonstrates the ability to model limited anisotropic in grain boundary energy and mobility. Anisotropic grain boundary energy is modeled by defining a weighted mode filter operation. Anisotropic grain boundary mobility is modeled by scaling and orienting the Gaussian neighborhood in a particular direction.

Anisotropy↗
NASA NTRS2012

Adaptive Control of Linear Modal Systems Using Residual Mode Filters and a Simple Disturbance Estimator

Flexible structures containing a large number of modes can benefit from adaptive control techniques which are well suited to applications that have unknown modeling parameters and poorly known operating conditions. In this paper, we focus on a direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend our adaptive control theory to accommodate troublesome modal subsystems of a plant that might inhibit the adaptive controller. In some cases the plant does not satisfy the requirements of Almost Strict Positive Realness. Instead, there maybe be a modal subsystem that inhibits this property. This section will present new results for our adaptive control theory. We will modify the adaptive controller with a Residual Mode Filter (RMF) to compensate for the troublesome modal subsystem, or the Q modes. Here we present the theory for adaptive controllers modified by RMFs, with attention to the issue of disturbances propagating through the Q modes. We apply the theoretical results to a flexible structure example to illustrate the behavior with and without the residual mode filter.

Balas, Mark↗
NASA NTRS2011

Adaptive Control Using Residual Mode Filters Applied to Wind Turbines

Many dynamic systems containing a large number of modes can benefit from adaptive control techniques, which are well suited to applications that have unknown parameters and poorly known operating conditions. In this paper, we focus on a model reference direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend this adaptive control theory to accommodate problematic modal subsystems of a plant that inhibit the adaptive controller by causing the open-loop plant to be non-minimum phase. We will augment the adaptive controller using a Residual Mode Filter (RMF) to compensate for problematic modal subsystems, thereby allowing the system to satisfy the requirements for the adaptive controller to have guaranteed convergence and bounded gains. We apply these theoretical results to design an adaptive collective pitch controller for a high-fidelity simulation of a utility-scale, variable-speed wind turbine that has minimum phase zeros.

Frost, Susan A.↗
NASA NTRS1989

Residual mode filters and adaptive control in large space structures

One of the most difficult problems in controlling large systems and structures is compensating for the destructive interaction which can occur between the reduced-order model (ROM) of the plant, which is used by the controller, and the unmodeled dynamics of the plant, often called the residual modes. The problem is more significant in the case of large space structures because their naturally light damping and high performance requirements lead to more frequent, destructive residual mode interaction (RMI). Using the design/compensation technique of residual mode filters (RMF's), effective compensation of RMI can be accomplished in a straightforward manner when using linear controllers. The use of RMF's has been shown to be effective for a variety of large structures, including a space-based laser and infinite dimensional systems. However, the dynamics of space structures is often uncertain and may even change over time due to on-orbit erosion from space debris and corrosive chemicals in the upper atmosphere. In this case, adaptive control can be extremely beneficial in meeting the performance requirements of the structure. Adaptive control for large structures is also based on ROM's and so destructive RMI may occur. Unfortunately, adaptive control is inherently nonlinear, and therefore the known results of RMF's cannot be applied. The purpose is to present the results of new research showing the effects of RMI when using adaptive control and the work which will hopefully lead to RMF compensation of this problem.

Davidson, Roger A.↗
NASA NTRSDate not supplied

Advancements in Burst-Mode Filtered Rayleigh Scattering for High-Speed Gas-Phase Multi-Parameter Measurements

Filtered Rayleigh scattering (FRS) can be used for velocity, density, temperature, and/or pressure measurements over a wide range of non-reacting flow conditions as well as more limited reacting flow conditions. However, the application of FRS to gas-phase measurements in large-scale test facilities can be limited due to low signal levels, strong background interferences, or the requirement for multiple cameras and/or molecular filters to spectrally resolve the signal. This work focuses on the spectral characteristics and wavelength-agility of burst-mode lasers for use in FRS systems. These advancements could improve measurement capability and data quality in applications with high levels of stray background scattering as well as where increased temporal resolution is desirable, such as high-speed flows.

filtered Rayleigh scattering↗
NASA NTRSDate not supplied

Demonstration of Frequency-Scanning Burst-mode Filtered Rayleigh Scattering for Multi-Parameter Gas-Phase Measurements

Filtered Rayleigh scattering (FRS) is a diagnostic technique used for measurements of macroscopic properties of a gas. The FRS signal is passed through a narrow bandwidth molecular filter, commonly gaseous iodine, to measure the broadening and Doppler-shift of the scattering light from the molecules of the gas flow. However, in single-frequency, intensity-based approaches, the effects of pressure, temperature, and velocity can be difficult to deconvolve. To overcome this challenge, frequency-scanning FRS has been used to quasi-spectrally resolve the signal. In this work, a frequency-scanned, burst-mode laser was used to perform scanning FRS in an underexpanded jet to measure temperature, pressure, and radial velocity at measurement rates up to 1 kHz which is ~100,000 times faster than prior implementations of scanning FRS.

filtered Rayleigh scattering↗
NASA NTRS1997

Direct and Inverse Techniques of Guided-Mode Resonance Filters Designs

Guided-mode resonances arise in single or multilayer waveguides where one or more homogeneous layers are replaced by diffraction gratings (Fig. 1.) The diffractive element enables an electromagnetic wave incident on a waveguide grating to be coupled to the waveguide modes supportable by the structure in the absence of the modulation (i.e. the difference between the high and low dielectric constants of the grating) at specific values of the wavelength and incident angle. The periodic modulation of the guide makes the structure leaky, preventing sustained propagation of modes in the waveguide and coupling the waves out into the substrate and cover. As the wavelength is varied around resonance a rapid variation in the intensities of the external propagating waves occurs. By selecting a grating period small enough to eliminate the higher-order propagating waves, an increase in the zero-order intensities up to 100% can result. The pronounced frequency selectivity of guided-mode resonances in dielectric waveguide gratings can be applied to design high-efficiency reflection and transmission filters [1-3].

Tibuleac, Sorin↗
NASA NTRS1988

Single-Mode Projection Filters for Modal Parameter Identification for Flexible Structures

Single-mode projection filters are developed for eigensystem parameter identification from both analytical results and test data. Explicit formulations of these projection filters are derived using the orthogonal matrices of the controllability and observability matrices in the general sense. A global minimum optimization algorithm is applied to update the filter parameters by using the interval analysis method. The updated modal parameters represent the characteristics of the test data. For illustration of this new approach, a numerical simulation for the MAST beam structure is shown by using a one-dimensional global optimization algorithm to identify modal frequencies and damping. Another numerical simulation of a ten-mode structure is also presented by using a two-dimensional global optimization algorithm to illustrate the feasibility of the new method. The projection filters are practical for parallel processing implementation.

Huang, Jen-Kuang↗
NASA NTRS1988

Modal identification using single-mode projection filters and comparison with ERA and MLE results

The Single-Mode Projection Filter (SPF) is a newly developed algorithm for eigensystem parameter identification from both analytical results and test data. The SPF is formulated with a single mode only and practical for parallel processing implementation. Explicit formulations of SPF are derived for the multi-input multi-output (MIMO) system by using the orthogonal matrices of the controllability and observability matrices in the general sense. The modal parameters of SPF are initially obtained from an analytical model in modal space. The experimental data are then processed through SPF to update its modal parameters and to minimize a cost function defined by the norm of an error matrix. The updated modal parameters represent the characteristics of the test data. A two-dimensional global minimum optimization algorithm is developed and applied for the filter update by using the interval analysis method. The SPF is developed based on a single-mode subsystem and identifies only one modal frequency and one modal damping within a specified region. For an n-modes structure, n SPF can be implemented for parallel processing to reduce the computational burden. The SPF is applied to analyze the simulated data for the MAST beam structure. The estimated modal parameters are comparable to those from the Eigensystem Realization Algorithm (ERA) and repeated modal frequencies are identified. The modal analysis of the Spacecraft Control Laboratory Experiment (SCOLE) data is also performed by using the ERA and the Maximum Likelihood Estimate (MLE). The result shows that the first five modal frequencies are very close from ERA and MLE. However, there are slight disparities in the damping rates and the computational burdens are quite different among these two algorithms.

Huang, Jen-Kuang↗
NASA NTRS1989

Single-mode projection filters for modal parameter identification for flexible structures

Single-mode projection filters are developed for eigensystem parameter identification from both analytical results and test data. Explicit formulations of these projection filters are derived using the orthogonal matrices of the controllability and observability matrices in the general sense. A global minimum optimization algorithm is applied to update the filter parameters by using the interval analysis method. The updated modal parameters represent the characteristics of the test data. For illustration of this new approach, a numerical simulation for the MAST beam structure is shown by using a one-dimensional global optimization algorithm to identify modal frequencies and damping. The projection filters are practical for parallel processing implementation.

Huang, Jen-Kuang↗
NASA NTRS1987

Single-mode projection filters for identification and state estimation of flexible structures

Single-mode projection filters are developed for eigensystem parameter identification and state estimation from both analytical results and test data. Explicit formulations of these projection filters are derived using the pseudoinverse matrices of the controllabilty and observability matrices in the general sense. A global minimum optimization algorithm is developed to update the filter parameters by using the interval analysis method. Modal parameters can be identified and updated in the global sense within a specified region of parameters by passing the experimental data through the projection filters. For illustration of this new approach, a numerical example is shown by using a one-dimensional global optimization algorithm to estimate modal frequencies and damping.

Huang, Jen-Kuang↗
DOE OSTI2025

Optimizing structured surfaces for diffractive waveguides

We introduce universal diffractive waveguide designs that can match the performance of conventional dielectric waveguides and achieve various functionalities. Optimized using deep learning, diffractive waveguides can be cascaded to form any desired length and are comprised of transmissive diffractive surfaces that permit the propagation of desired modes with low loss and high mode purity. In addition to guiding the targeted modes through cascaded diffractive units, we also developed various waveguide components and introduced bent diffractive waveguides, rotating the direction of mode propagation, as well as spatial and spectral mode filtering and mode splitting diffractive waveguide designs, and mode-specific polarization control. This framework was experimentally validated in the terahertz spectrum to selectively pass certain spatial modes while rejecting others. Without the need for material dispersion engineering diffractive waveguides can be scaled to operate at different wavelengths, including visible and infrared spectrum, covering potential applications in, e.g., telecommunications, imaging, sensing and spectroscopy.

Applied optics↗
NASA NTRS1992

Two-mode elliptical-core weighted fiber sensors for vibration analysis

Two-mode, elliptical-core optical fibers are demonstrated in weighted, distributed and selective vibration-mode-filtering applications. We show how appropriate placement of optical fibers on a vibrating structure can lead to vibration mode filtering. Selective vibration-mode suppression on the order of 10 dB has been obtained using tapered two-mode, circular-core fibers with tapering functions that match the second derivatives of the modes of vibration to be enhanced. We also demonstrate the use of chirped, two-mode gratings in fibers as spatial modal sensors that are equivalents of shaped piezoelectric sensors.

Vengsarkar, Ashish M.↗
NASA NTRSDate not supplied

LIPA: Lunar Ice Perception Algorithm

Introduction: The highest concentration of Lu-nar water-ice stores exists within the Permanently Shadowed Regions (PSRs) of the Lunar South Pole [1-3]. As such, the ability to locate in situ water-ice stores in an accurate, systematic, and safe manner will prove vital for future Lunar activities which rely on hydrogen-based resources. Here we show how the strong absorptive properties of ice can be exploited so that surface ice located in PSRs can be easily differentiated from the surrounding frozen regolith. Testbeds which simulate an icy lunar landscape were created and then systematically imaged using a mid-wave infrared (MWIR) camera system. Testbeds were imaged under two filter modes (1) high-absorption (high-abs) mode: whereby imagery captured were confined to a single central wave-length (CWL) of 3.15 ± 0.03 μm and (2) low-absorption (low-abs) mode: whereby imagery cap-tured were confined to a single CWL of 3.80 ± 0.04 μm (Figure 1). High- and low-absorption modes are related to the absorptive properties of ice at each selected wavelength, respectively. Corresponding images from each filter mode were differenced (i.e., pixels were subtracted) to enhance contrast between ice-bearing and non-ice-bearing pixels, and then fed into a semantic segmen-tation model. The model was trained to detect and differentiate between water, ice, shadows, and lunar regolith. Results: Modeling results accurately discrimi-nated ice from other materials (such as frozen lunar regolith) and were used to visually resolve the spa-tial extent of surface ice. Further, outputs produced through semantic segmentation were used to estimate water-ice contents in collected imagery [(Pixels with Class = “Water Ice”)/(Sum of Pixels)*100]. Summary: These works prove promising for future in situ resource utilization (ISRU) missions which employ robotics in combination with infrared camera systems to advance science objectives (e.g., locate water-ice in frozen regolith) on the lunar sur-face. References: [1] Cannon K. M., Deutsch A. N., Head J. W., and Britt D. T. (2020) Geophysical Re-search Letters, 46, e2020GL088920. [2] Honniball C. I. et al. (2021) Nature Astronomy 5, no. 2, 121-127. [3] Li S. et al. (2018) Proceedings of the National Academy of Sciences, 115(36), 8907-8912.

A. Slabic↗
NASA NTRS2012

Disturbance Accommodating Adaptive Control with Application to Wind Turbines

Adaptive control techniques are well suited to applications that have unknown modeling parameters and poorly known operating conditions. Many physical systems experience external disturbances that are persistent or continually recurring. Flexible structures and systems with compliance between components often form a class of systems that fail to meet standard requirements for adaptive control. For these classes of systems, a residual mode filter can restore the ability of the adaptive controller to perform in a stable manner. New theory will be presented that enables adaptive control with accommodation of persistent disturbances using residual mode filters. After a short introduction to some of the control challenges of large utility-scale wind turbines, this theory will be applied to a high-fidelity simulation of a wind turbine.

Frost, Susan↗