Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mode-I fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

Fracture mechanics of shales under chemically reactive conditions

Fracture growth processes under subsurface conditions are known to be affected by fluid chemical environment. Chemical effects on fracture growth are likely to be relevant during host rock and organic matter diagenesis and catagenesis, hydraulic fracturing, in systems undergoing enhanced oil recovery, in geothermal systems, and in CO 2 sequestration reservoirs. To address the chemical effects on opening-mode fracture growth under a wide range in fluid chemical conditions and for different rock types we conducted double-torsion fracture mechanics tests to determine mode-I fracture toughness (KIC), subcritical index (SCI), and the stress-intensity factor vs fracture velocity (K-V) behavior. We tested sandstones, shales and, altered crystalline rocks. Samples were tested in aqueous conditions with variable salinity, solution pH, and at temperatures of up to 70 °C. Fracture growth in shales is highly sensitive to the environmental conditions, with a reduction of KIC of up to 47% from ambient air to water-saturated conditions. The primary interactions between shales and reactive solutions are clay-water and carbonate dissolution. For clay-rich Woodford and Mancos shales, solutions with higher salinity reduce subcritical fracture growth, while acidic conditions favor fracture growth in carbonate-rich Marcellus shale. Increasing the solution temperature promotes fracture growth. In sandstone, chemical effects on fracture parameters are most pronounced for clay- and carbonate-rich samples. Both KIC and SCI are lower in water than in air for nearly all sandstone lithologies tested. SCI is further reduced in chlorite-cemented Tuscaloosa Sandstone in acidic solutions. Mount Simon Sandstone is also sensitive to pH, most significantly in diagenetically bleached samples. Compositionally mature Aztec Sandstone is affected by water saturation, but shows little sensitivity to chemical environment. Silicified gabbro shows a slight reduction in KIC but a >60% reduction in SCI in aqueous environments compared to ambient conditions. The reduction in SCI is most pronounced in alkaline and saline solutions, suggesting silica dissolution and cation exchange at the fracture tip facilitate subcritical fracture growth. Limited reduction in KIC is attributed to low permeability. Overall, our results demonstrate that fracture properties depend strongly on water saturation, on fluid composition and pH, and on temperature, with an increase in temperature lowering fracture resistance.

58 GEOSCIENCES↗

Subcritical fracturing of shales under chemically reactive conditions

Growth of opening-mode fractures under chemically reactive subsurface conditions is potentially relevant for seal integrity in subsurface CO2 storage and hazardous waste disposal. Using double-torsion load relaxation tests we determine mode-I fracture toughness (KIC), subcritical index (SCI), and the stress-intensity factor vs fracture velocity (K-V) behavior of Marcellus, Woodford, and Mancos shales. Samples are tested under ambient air and aqueous conditions with variable NaCl and KCl concentrations, variable pH, and temperatures of up to 70°C. Under ambient air condition, KIC determined from double torsion tests is 1.3, 0.6, and 1.1 MPa∙m1/2 for Marcellus, Woodford, and Mancos shales, respectively. SCI under ambient air condition is between 55 and 90 for the shales tested. Tests in aqueous solutions show a significant drop of KIC compared to ambient air condition. For tests in deionized water, KIC reduction is 18.5% for Marcellus and 47.0% for Woodford. The presence of aqueous fluids also results in a reduction of the SCI up to 85% compared to ambient condition. K-V curves generally obey a power-law relation throughout the load-relaxation period. However, aqueous-based tests on samples result in K-V curves deviating from the power-law relation, with the SCI values gradually decreasing with time during the relaxation period. This non-power-law behavior is obvious in Woodford and Mancos, but negligible in Marcellus. We find that the shales interact with the aqueous solution both at the fracture tip and within the rock matrix during subcritical fracturing. For Marcellus shale, water mainly interacts with the fracture tip on both tests due to low matrix permeability and less reactive mineral composition. However, Woodford and Mancos react strongly with water causing significant sample degradation. The competition between degradation and fracture growth results in the time-dependent SCI: at lower fracture velocities, the tip interacts longer with the chemically altered area around the tip; at higher fracture velocities, the fracture propagates through the altered area before significant degradation. Our results display strong weakening effects of chemically reactive fluids on subcritical fracture properties with implications on subsurface storage seal performance.

58 GEOSCIENCES↗

Intergranular fracture in UO2: derivation of traction-separation law from atomistic simulations

In this study, the intergranular fracture behavior of UO2 was studied by molecular dynamics simulations using the Basak potential. In addition, the constitutive traction-separation law was derived from atomistic data using the cohesive-zone model. In the simulations a bicrystal model with the (100) symmetric tilt E5 grain boundaries was utilized. Uniaxial tension along the grain boundary normal was applied to simulate Mode-I fracture. The fracture was observed to propagate along the grain boundary by micro-pore nucleation and coalescence, giving an overall intergranular fracture behavior. Phase transformations from the Fluorite to the Rutile and Scrutinyite phases were identified at the propagating crack tips. These new phases are metastable and they transformed back to the Fluorite phase at the wake of crack tips as the local stress concentration was relieved by complete cracking. Such transient behavior observed at atomistic scale was found to substantially increase the energy release rate for fracture. Insertion of Xe gas into the initial notch showed minor effect on the overall fracture behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Intergranular fracture in UO{sub 2}: derivation of traction-separation law from atomistic simulations

In this study, the intergranular fracture behavior of UO{sub 2} was studied by molecular dynamics simulations using the Basak potential. In addition, the constitutive traction-separation law was derived from atomistic data using the cohesive-zone model. In the simulations a bicrystal model with the (100) symmetric tilt Σ5 grain boundaries was utilized. Uniaxial tension along the grain boundary normal was applied to simulate Mode-I fracture. The fracture was observed to propagate along the grain boundary by micro-pore nucleation and coalescence, giving an overall intergranular fracture behavior. Phase transformations from the Fluorite to the Rutile and Scrutinyite phases were identified at the propagating crack tips. These new phases are metastable and they transformed back to the Fluorite phase at the wake of crack tips as the local stress concentration was relieved by complete cracking. Such transient behavior observed at atomistic scale was found to substantially increase the energy release rate for fracture. Insertion of Xe gas into the initial notch showed minor effect on the overall fracture behavior. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hybrid fiber metal composite laminate interlaminar reinforcement through metal interlocks

Aircraft and automobile industries are continually seeking high-performance and lightweight solutions. Fiber-reinforced composites in conjunction with metals are being considered in the form of hybrid materials. There is a continuous need for improvement of interfacial bonding between composite layers and metal constituents. In this study, an innovative hybrid fiber interlocking metal hooks laminate (FIMHL) system was developed in which fiber-reinforced thermoset composite, and metal sheets are mechanically bonded together using out of plane hooks stamped in the metal. Process optimization was performed to gain the full benefit of the through-thickness reinforcement. Microstructural analysis showed improved interaction between the metal hooks and the fiber layers which reduced porosity and resin richness. This was reflected in mechanical properties, as tensile and flexural strength of FIMHL was enhanced by 38.5 and 18.8%, respectively, after process optimization. Furthermore, normalized weight fraction (76.4%) properties of FIMHL also confirmed that the increase in mechanical properties of optimized panel were not only due to increased reinforcement (glass fiber + aluminum) volume fraction but also because of improved metal hooks and fibers interaction. There was no significant effect on lap shear and fracture toughness, as they depend on bend back behavior of the hooks. A bilinear traction-separation model was used to characterize mode-I interlaminar fracture toughness properties, and 4.5% variation was recorded when modeling and experimental values were compared.

36 MATERIALS SCIENCE↗

Fracture toughness evaluation for Zr-4 clad tubing structure with pellet inserts

Applying fracture mechanics approach to spent nuclear fuel (SNF) system reliability investigation is warranted due to the inherent flaws and hydride structures existed in a SNF system after nuclear reactor operation. However, none of the existing fracture toughness data deal with fuel cladding specific geometry or spent fuel material conditions, such as cladding structure with the pellet-inserts and the associated pellet clad mechanical interactions induced mixed-mode damage mechanisms. Thus, the development of an intrinsic fracture mechanics approach that is suitable for SNF materials is needed. Due to thin wall and small dimension of clad tubing structure, the spiral notch torsion test (SNTT) method of small specimen approach was used to estimate the clad tubing structure fracture toughness. The estimated fracture toughness for Zr-4 cladding with alumina-pellet inserts are presented in this report. For SNTT samples with a short or medium crack length, between 5.4-mm and 8-mm, the estimate JIQ upon fracture initiation for the baseline Zr-4 cladding is at 50 kJ/m2 with 2-sigma uncertainty of 3.26 kJ/m2, and the associated KIQ is at 67.46 MPa√m. For SNTT samples with a long crack length, around 13-mm, the crack initialization is deviated from that of the Mode-I tensile fracture and appears to be a mixed-mode fracture of Mode I – tensile stress and Mode III – out of plane shear stress; the estimated JMQ is at 18.9 kJ/m2, the associated KMQ is at 41.4 MPa√m.

36 MATERIALS SCIENCE↗

Fracture toughness evaluations for spent nuclear fuel dry storage canister welds and spent nuclear fuel clad-pellet structures

Integrity of spent nuclear fuel (SNF) interim storage canisters is very important to the safety of the back-end nuclear fuel cycle. Stress corrosion cracking (SCC) potential of interim storage canister has been considered as a high priority. Because no post-weld heat treatment was required for forming these canisters, the high tensile residual stress existed within these canister welds. This can change the fracture resistance capacity significantly as well as increase SCC potential. Due to relative thin shell thickness of a canister weldment, the spiral notch torsion test (SNTT) method was used to estimate the canister weldment fracture toughness. SNTT was developed to measure the intrinsic fracture toughness of structural materials using small specimens. The SNTT method has been applied to a wide variety of structural materials, such as low-alloy steels, stainless steel, aluminum alloy, ceramics, concrete, and composites. The SNTT system operates by applying pure torsion to cylindrical specimens with a notch line that spirals around the specimen at a 45° pitch. In order to carry out pure torsion load mode, biaxial tension/torsion tester was developed accordingly to perform SNTT protocol. Moreover, applying fracture mechanics approach to SNF system reliability investigation is warranted due to the inherent flaws and hydride structures existed in a SNF system after nuclear reactor operation. However, none of the existing fracture toughness data deal with fuel cladding specific geometry or spent fuel material conditions, such as cladding structure with the pellet-inserts and the associated pellet clad mechanical interactions induced mixed-mode damage mechanisms. Thus, the development of an intrinsic fracture mechanics approach that is suitable for SNF materials is needed. Furthermore, due to thin wall and small dimension of clad tubing structure, the SNTT method was used to estimate the clad tubing structure fracture toughness. Fracture testing were performed on the received stainless steel canister weldment, most SNTT weld samples fracture initiation sites are at heat-affected zone (HAZ) regions. The estimated fracture toughness J Q ’ for the baseline SS304 steel is at 283 kJ/m². The estimated JQ’ for the SS304/308 weld and baseline metals are 148 kJ/m 2 and 459 kJ/m 2 , respectively. Out of cell fracture testing for spent fuel structure were carried out on the surrogate rods made of Zr-4 clad and alumina inserts, the estimated fracture toughness values for baseline Zr-4 cladding with alumina-pellet inserts are: (1) For SNTT samples with a short or medium crack length, between 5.4-mm and 8-mm, the estimate J IQ upon fracture initiation for the baseline Zr-4 cladding is at 50 kJ/m 2 with 2-sigma uncertainty of 3.26 kJ/m 2 , and the associated K IQ is at 67.46 MPa$\sqrt{m}$; and (2) For SNTT samples with a long crack length, around 13-mm, the crack initialization is deviated from that of the Mode-I tensile fracture and appears to be a mixed-mode fracture of Mode I - tensile stress and Mode III - out of plane shear stress; the estimated J MQ is at 18.9 kJ/m 2 , the associated K MQ is at 41.4 MPa$\sqrt{m}$.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Significant slowdown of plasma-optimized surface energy deactivation by vacuum sealing for efficient adhesive bonding

This work proposes an approach to minimize surface energy deactivation of plasma-treated metal and carbon fiber-reinforced polymer (CFRP) surfaces by vacuum sealing. Plasma treatments enhance adhesive wettability on post-treated surfaces for adhesive joints, but the treated surfaces deactivate quickly in air. The surface energy of aluminum alloy AA6061 and carbon fiber-reinforced polymer-polyamide (CFRP-PA66) optimally treated by a blown air plasma instrument returns to the original surface energy within one hour. Vacuum sealing of AA6061 and CFRP-PA66 reduced the surface energy deactivation over 7 days by at least 230 times and 970 times compared to in air. Double Cantilever Beam (DCB) tests performed on adhesively-bonded AA6061/CFRP-PA66 joints showed that the total energy release and energy dissipation before failure of plasma-treated and vacuum-sealed materials was up to 60% more than plasma-treated materials without vacuum sealing and up to 125% more than non-plasma-treated materials.

42 ENGINEERING↗

Mixed-Mode and Mode-II Fatigue Crack Growth in Woven Composites

In this work, a woven carbon/epoxy composite was subjected to fatigue crack growth under mixed Mode-I/Mode-II loading to obtain crack growth behavior at different cyclic strain energies. Owing to the woven structure of the material, pure Mode-II fracture is usually a difficult proposition because of friction, interference, and interlock of woven tows in adjacent plies at an interlaminar crack. These limitations were overcome by the use of a novel form of mixed Mode-I/Mode-II specimen, which imposes sufficient crack surface opening (Mode-I) to alleviate ply-ply interactions, but not so much as to obscure the sliding (Mode-II) response. Finally, comparison with pure Mode-I fatigue crack growth data, in conjunction with a fracture interaction criterion, provided a means to extract the Mode-II behavior.

36 MATERIALS SCIENCE↗

Edge cracks in nickel and aluminium single crystals: A molecular dynamics study

A molecular dynamics study of edge cracks in Ni and Al single crystals under mode-I loading conditions is presented. Simulations are performed using embedded-atom method potentials for Ni and Al at a temperature of 0.5 K. The results reveal that Ni and Al show different fracture mechanisms. Overall failure behavior of Ni is brittle, while fracture in Al proceeds through void nucleation and coalescence with a zig-zag pattern of crack growth. The qualitative nature of results is discussed in the context of vacancy-formation energies and surface energies of the two FCC metals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Attaining regularization length insensitivity in phase-field models of ductile failure

In this work, a cohesive phase-field model of ductile fracture in a finite-deformation setting is presented. The model is based on a free-energy function in which both elastic and plastic work contributions are coupled to damage. Using a strictly variational framework, the field evolution equations, damage kinetics, and flow rule are jointly derived from a scalar least-action principle. Particular emphasis is placed on the use of a rational function for the stress degradation that maintains a fixed effective strength with decreasing regularization length. The model is employed to examine crack growth in pure mode-I problems through the generation of crack growth resistance (J-R) curves. In contrast to alternative models, the current formulation gives rise to J-R curves that are insensitive to the regularization length. Numerical evidence suggests convergence of local fields with respect to diminishing regularization length as well.

42 ENGINEERING↗

Deformation fields near a steady fatigue crack with anisotropic plasticity

In this work, from finite element simulations based on an irreversible, hysteretic cohesive interface model, a steady fatigue crack can be realized if the crack extension exceeds about twice the plastic zone size, and both the crack increment per loading cycle and the crack bridging zone size are smaller than the plastic zone size. The corresponding deformation fields develop a plastic wake behind the crack tip and a compressive residual stress field ahead of the crack tip. In addition, the Hill’s plasticity model is used to study the role of plastic anisotropy on the retardation of fatigue crack growth and the elastic strain fields. It is found that for Mode-I cyclic loading, an enhanced yield stress in directions that are inclined from the crack plane will lead to slower crack growth rate, but this retardation is insignificant for typical degrees of plastic anisotropy. Furthermore, these results provide key inputs for future comparisons to neutron and synchrotron diffraction measurements that provide full-field lattice strain mapping near fracture and fatigue crack tips, especially in textured materials such as wrought or rolled Mg alloys.

36 MATERIALS SCIENCE↗

Modeling the influence of bubble pressure on grain boundary separation and fission gas release

Grain boundary (GB) separation as a mechanism for fission gas release (FGR), complementary to gas bubble interlinkage, has been experimentally observed in irradiated light water reactor fuel. However there has been limited effort to develop physics-based models incorporating this mechanism for the analysis of FGR. In this work, a computational study is carried out to investigate GB separation in UO2 fuel under the effect of gas bubble pressure and hydrostatic stress. A non-dimensional stress intensity factor formula is obtained through 2D axisymmetric analyses considering lenticular bubbles and Mode-I crack growth. The obtained functional form can be used in higher length-scale models to estimate the contribution of GB separation to FGR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dislocation and Structural Studies at Metal–Metallic Glass Interface at Low Temperature

In this paper, molecular dynamics (MD) simulation deformation studies on the Al (metal)–Cu{sub 50}Zr{sub 50} (metallic glass) model interface is carried out based on cohesive zone model. The interface is subjected to mode-I loading at a strain rate of 10{sup 9} s{sup −1} and temperature of 100 K. The dislocations reactions and evolution of dislocation densities during the deformation have been investigated. Atomic interactions between Al, Cu and Zr atoms are modeled using EAM (embedded atom method) potential, and a timestep of 0.002 ps is used for performing the MD simulations. A circular crack and rectangular notch are introduced at the interface to investigate the effect on the deformation behavior and fracture. Further, scale size effect is also investigated. The structural changes and evolution of dislocation density are also examined. It is found that the dominant deformation mechanism is by Shockley partial dislocation nucleation. Amorphization is observed in the Al regions close to the interface and occurs at a lower strain in the presence of a crack. The total dislocation density is found to be maximum after the first yield in both the perfect and defect interface models and is highest in the case of perfect interface with a density of 6.31 × 10{sup 17} m{sup −2}. In the perfect and circular crack defect interface models, it is observed that the fraction of Shockley partial dislocation density decreases, whereas that of strain rod dislocations increases with increase in strain.

36 MATERIALS SCIENCE↗