Search NASA⌕ Search

SEARCH · Search NASA

Results for “Moisture Barrier”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Evaluation of moisture barrier coatings on carbon-phenolic SRM nozzle materials

The carbon-phenolic composite ablative material used on the Solid Rocket Motor (SRM) nozzle is known to absorb moisture from the atmosphere. This could cause problems such as pocketing during firing. Several moisture barrier coatings were tested on the SRM nozzle material. Data are presented for six of the 12 coatings to be tested. The data were obtained from immersion of coated samples in an environmental chamber at 100 F and 100% relative humidity and by using a modified TGA (thermal gravimetric analysis) technique. The TGA technique involved allowing wet nitrogen (25 C, 80% relative humidity) to flow across a small sample at about 65 cu cm per minute while continually monitoring the weight increase. These preliminary results show Kel-F-800, a material supplied by 3M Corporation to be the better moisture barrier. A second task was to collect data on the relative absorption of water and kerosene into the carbon-phenolic SRM nozzle material. These data indicate that water absorbs into the nozzle material to a much greater extent than kerosene. Thus kerosene is the more likely solvent in which to make specific gravity measurements on the SRM nozzle material.

Mcnutt, Ronald C.↗
NASA NTRS2000

Evaluation of GE-167 Silicone Rubber (RTV) For Possible Service As A Moisture-Barrier For Certain Strain Gage Applications

The Langley Research Center uses strain gages in a wide variety of demanding test environments. Strain gage installations, depending on the testing scenario, may see high temperatures, cryogenic temperature, moisture accumulation, mechanical abuse, or any combination of these conditions. At Langley, there is often a need to provide protection for strain gages against moisture and mechanical abuse, especially when large-scale, harsh environment testing is to be encountered. This technical memorandum discusses the evaluation of a room temperature curing silicone rubber sealant manufactured by the General Electric Company for consideration as a moisture-barrier for certain strain gage installations.

Hare, David A.↗
NASA NTRS1990

Diamondlike carbon as a moisture barrier and antireflecting coating on optical materials

Diamondlike carbon (DLC) is amorphous, hard, semitransparent, and is under consideration for use as a coating material for infrared optics. DLC is also designated as a-C:H to indicate its amorphous nature as well as to indicate the presence of large (20 to 55 percent) amounts of hydrogen in the film. Two important questions arise with respect to use of DLC in infrared optics. Will the lack of grain boundaries help to keep moisture from penetrating the film. Secondly, application as an antireflection coating places restrictions on the allowed values of the index of refraction of the film relative to the particular substrate material being used. Will DLC have the correct index range. These two questions are addressed in this paper.

Woollam, John A.↗
NASA NTRS1998

Fire Resistant, Moisture Barrier Membrane

A waterproof and breathable, fire-resistant laminate is provided for use in tents, garments, shoes, and covers, especially in industrial, military and emergency situations. The laminate permits water vapor evaporation while simultaneously preventing liquid water penetration. Further, the laminate is fire-resistant and significantly reduces the danger of toxic compound production when exposed to flame or other high heat source. The laminate may be applied to a variety of substrates and is comprised of a silicone rubber and plurality of fire-resistant, inherently thermally-stable polyimide particles.

St.Clair, Terry L.↗
NASA NTRS2000

Fire Resistant, Moisture Barrier Membrane

A waterproof and breathable, fire-resistant laminate is provided for use in tents, garments, shoes, and covers, especially in industrial, military and emergency situations. The laminate permits water vapor evaporation while simultaneously preventing liquid water penetration. Further, the laminate is fire-resistant and significantly reduces the danger of toxic compound production when exposed to flame or other high heat source. The laminate may be applied to a variety of substrates and is comprised of a silicone rubber and plurality of fire-resistant, inherently thermally-stable polyimide particles.

St.Clair, Terry L.↗
NASA NTRS1973

A Non Rigid Reusable Surface Insulation Concept for the Space Shuttle Thermal Protection System

A reusable thermal protection system concept was developed for the space shuttle that utilizes a flexible, woven ceramic mat insulation beneath an aerodynamic skin and moisture barrier consisting of either a dense ceramic coating or a super alloy metallic foil. The resulting heat shield material has unique structural characteristics. The shear modulus of the woven mat is very low such that bending and membrane loads introduced into the underlying structural panel remain isolated from the surface skin.

Alexander, J. G.↗
NASA NTRS1974

Coating processes for increasing the moisture resistance of polyurethane baffle material

An investigation was conducted with the objective to improve the hydrolytic stability of reticulated polyurethane baffle material. This material is used in fuel tanks of aircraft and ground vehicles. The most commonly used foam of this type is hydrolytically unstable. Potential moisture barrier coatings which were evaluated include Parylene, epoxy-polysulfide, polyether based polyurethanes, polysulfides, polyolefin rubbers, and several other materials. Parylene coatings of at least 0.2 mil were found to provide the greatest improvement in hydrolytic stability.

Bilow, N.↗
NASA NTRS1975

Storage stability and improvement of intermediate moisture foods, phase 2

Methods for improvement of shelf-life stability of intermediate moisture foods are considered. It was found that vitamin C is the most limiting vitamin from a nutritional standpoint with its rate of destruction increasing with a sub w. Techniques for microbial challenge studies were developed. It was shown that organisms have a higher growth a sub w limit if the IMF is prepared by the adsorption process and long times are needed for challenge studies. Several alternative antimycotic systems were found. It was also found that the vegetative cells of pathogens have a maximum heat resistance in the IMF a sub w range. If glycols are in the formula, the IMF should have as high an a sub w as possible. The reverse is true if lipid oxidation occurs. In addition, to prevent rancidity, antioxidants and a low O2 atmosphere are necessary. The package also must be a good moisture barrier.

Labuza, T. P.↗
NASA NTRS1978

Evaluations of candidate encapsulation designs and materials for low-cost silicon photovoltaic arrays

Three encapsulation designs for silicon photovoltaic arrays based on cells with silk-screened Ag metallization have been evaluated: transparent polymeric coatings over cells laminated between two films or sheets of polymeric materials; cells adhesively bonded to a glass cover with a polymer pottant and a glass or other substrate component. Silicone and acrylic coatings were assessed, together with acrylic sheet, 0.635 mm fiberglass-reinforced polyester sheet, 0.102 mm polycarbonate/acrylic dual-layer film, 0.127 mm fluorocarbon film, soda-lime glass, borosilicate glass, low-iron glass, and several adhesives. The encapsulation materials were characterized by light transmittance measurements, determination of moisture barrier properties and bond strengths, and by the performance of cells before and after encapsulation. Silicon and acrylic coatings provided inadequate protection. Acrylic and fluorocarbon films displayed good weatherability and acceptable optical transmittance. Borosilicate, low-iron and soda-lime-float glasses were found to be acceptable candidate encapsulants for most environments.

Gaines, G. B.↗
NASA NTRS1999

Use of Several Thermal Analysis Techniques on a Hypalon Paint Coating for the Solid Rocket Booster (SRB) of the Space Shuttle

White Hypalon paint is brush-applied as a moisture barrier coating over cork surfaces on each of the two Space Shuttle SRBS. Fine cracks have been observed in the Hypalon coating three times historically on laboratory witness panels, but never on flight hardware. Recent samples of the cracked and standard ("good") Hypalon were removed from cork surfaces and were tested by Thermal Gravimetric Analysis (TGA), Thermomechanical (TMA) and Differential Scanning Calorimetry (DSC) thermal analysis techniques. The TGA data showed that at 700 C, where only paint pigment solids remain, the cracked material had about 9 weight percent more material remaining than the standard material, probably indicating incomplete mixing of the paint before it was brush-applied to produce the cracked material. Use of the TMA film tension method showed that the average static modulus vs. temperature was about 3 to 6 times higher for the cracked material than for the standard material, indicating a much higher stiffness for the cracked Hypalon. The TMA data also showed than an increased coating thickness for the cracked Hypalon was not a factor in the anomaly.

Wingard, Charles D.↗
NASA NTRS2000

Use of Several Thermal Analysis Techniques on a Hypalon Paint Coating for the Solid Rocket Booster (SRB) of the Space Shuttle

White Hypalon paint is brush-applied as a moisture barrier coating over cork surfaces on each of the two Space Shuttle SRBs. Fine cracks have been observed in the Hypalon coating three times historically on laboratory witness panels, but never on flight hardware. Samples of the cracked and standard ("good") Hypalon were removed from witness panel cork surfaces, and were tested in 1998 by Thermogravimetric Analysis (TGA), TMA and Differential Scanning Calorimetry (DSC) thermal analysis techniques. The TGA data showed that at 700C, where only paint pigment solids remain, the cracked material had about 9 weight percent more material remaining than the standard material, probably indicating incomplete mixing of the paint before it was brush-applied to produce the cracked material. Use of the TMA film/fiber technique showed that the average modulus (stiffness) vs. temperature was about 3 to 6 times higher for the cracked material than for the standard material. The TMA data also showed that an increase in coating thickness for the cracked Hypalon was not a factor in the anomaly.

Wingard, Charles D.↗
NASA NTRS2000

Reliable, Low-Cost, Low-Weight, Non-Hermetic Coating for MCM Applications

Through an Air Force Research Laboratory sponsored STM program, reliable, low-cost, low-weight, non-hermetic coatings for multi-chip-module(MCK applications were developed. Using the combination of Sandia Laboratory ATC-01 test chips, AvanTeco's moisture sensor chips(MSC's), and silicon slices, we have shown that organic and organic/inorganic overcoatings are reliable and practical non-hermetic moisture and oxidation barriers. The use of the MSC and unpassivated ATC-01 test chips provided rapid test results and comparison of moisture barrier quality of the overcoatings. The organic coatings studied were Parylene and Cyclotene. The inorganic coatings were Al2O3 and SiO2. The choice of coating(s) is dependent on the environment that the device(s) will be exposed to. We have defined four(4) classes of environments: Class I(moderate temperature/moderate humidity). Class H(high temperature/moderate humidity). Class III(moderate temperature/high humidity). Class IV(high temperature/high humidity). By subjecting the components to adhesion, FTIR, temperature-humidity(TH), pressure cooker(PCT), and electrical tests, we have determined that it is possible to reduce failures 50-70% for organic/inorganic coated components compared to organic coated components. All materials and equipment used are readily available commercially or are standard in most semiconductor fabrication lines. It is estimated that production cost for the developed technology would range from $1-10/module, compared to $20-200 for hermetically sealed packages.

Jones, Eric W.↗
NASA NTRS1966

Impact and puncture resistant material protects parts from damage

Uniform sized, laminated panels protect delicate parts and equipment from damage during storage and transportation. The panels consist of sheets of steel foil bonded between sheets of elastic foam. They are lightweight, impact and puncture-resistant, and, when formed into an enclosure, provide a barrier against moisture and thermal shock.

Sheriff, D. D.↗
NASA NTRS1967

Double copper sheath multiconductor instrumentation cable is durable and easily installed in high thermal or nuclear radiation area

Multiconductor instrumentation cable in which the conducting wires are routed through two concentric copper tube sheaths, employing a compressed insulator between the conductors and between the inner and outer sheaths, is durable and easily installed in high thermal or nuclear radiation area. The double sheath is a barrier against moisture, abrasion, and vibration.

Mc Crae, A. W., Jr.↗
NASA NTRS1980

Photonitride passivating coating for IC's

Increased reliability and simplified fabrication result from postassembly preencapsulation passivation process. Photonitride reaction chamber receives silane, ammonia, and mercury from mixing manifold to form passivating coating on IC's. Photonitride layer is barrier to moisture and penetration by mobile ions, and helps to protect IC devices subjected to severe mechanical handling or circuit repair procedures. Process is compatible with variety of wire-bonded lead frame assemblies. Advantages over plasma and sputtering deposition processes are low deposition temperature and zero stray radiation and ion levels.

Hall, T. C.↗
NASA NTRS1991

Unique applications of fluoroepoxy materials

The following subject areas are covered: (1) fluoroepoxy and curing agents; (2) an excellent moisture vapor barrier coating; (3) as adhesives to bond Teflon without any surface treatment; (4) a new method to make thermosetting fluoropolymer foam; and (5) as a new antifoaming agent for epoxy material manufacturing and processing.

Lee, Sheng Yen↗
NASA NTRSDate not supplied

Polymeric Materials Application and Testing for Space Missions

The EM41 Non-metallics polymers team performs polymeric materials screening, characterization, development, qualification, verification and validation testing for flight hardware and in-space applications. They perform insight, testing and application of polymeric materials for launch vehicles and space environments. Personnel have a deep understanding of the technologies associated with cryogenic insulation, high temperature thermal protection materials, paints, primers, coatings, and adhesive materials. Numerous TPS material characterization tests can also be performed by the Lab. The team has both internal and partner test capabilities to subject polymeric materials to Aerospace and Space environments Material properties, response and performance are tested within environments from the launch pad, through the launch environment and into space. A primary role of the team is to select materials and organize test regimen then analyze test results. Test regiment are established to confirm the materials meet the performance requirements levied by customers within the environments that are expected for the mission.

Thermal↗